共查询到20条相似文献，搜索用时 46 毫秒
1.
F. Colangelo 《地震工程与结构动力学》2005,34(10):1219-1241
This paper presents pseudo‐dynamic test results on the in‐plane seismic behaviour of infilled frames. Thirteen single‐storey, single‐bay, half‐size‐scale, reinforced concrete‐frame specimens, most of which infilled with non‐structural masonry made of perforated bricks and cement mortar are tested. The infills are in contact with frames, without any connector; openings are not covered. The frames are different in their strength and details, reinforcement grade, and aspect ratio. Seismic input is the 1976 Tolmezzo (Friuli, Italy) ground acceleration, to which specimens are subjected two times: virgin and damaged by the previous test. The global seismic response of initially virgin infilled specimens considerably differs from that of bare specimens. This follows a dramatic change of properties: compared to a bare frame, the initial stiffness increases by one order of magnitude, and the peak strength more than doubles. The peak drift lessens; however, the displacement ductility demand does not. The energy demand is greater. Nevertheless, the influence of infill decreases as damage proceeds. Displacement time histories of damaged specimens are quite similar. At the local level, infill causes asymmetry and concentration of the frame deformation. Copyright © 2005 John Wiley & Sons, Ltd. 相似文献
2.
Unreinforced masonry (URM) infill panels are widely used as partitions in RC frames and typically considered as non‐structural elements in the design process. However, observations from recent major earthquakes have shown that under seismic excitation, the structural interaction between columns and infill walls can significantly alter the structural behaviour, thus causing catastrophic consequences. The purpose of this research was to propose and test an innovative low seismic damage detailing method, which isolates the infill panel from bounding columns with finite width vertical gaps during the infill panel construction phase and deploys steel wire connections in mortar layers anchored to columns. Taking into account the similitude requirements, a total of six one‐third scale, single‐storey single‐bay RC frames with different infill configurations and flexible connection details were carefully designed and tested on a shake‐table. Three real earthquake records were selected and scaled to ascending intensity levels and used as input signals. A series of thorough investigations including dynamic characteristics, hysteretic behaviour, failure mechanisms, out‐of‐plane vulnerabilities and the effect of different gap filling materials and load transfer mechanisms were rigorously studied. The experimental results indicate that the undesirable interaction between infill panels and bounding frame is significantly reduced using the proposed low seismic damage detailing concept. Direct shear failure of columns at an early stage is prevented, and structural redundancy at high levels of excitation can be provided. In general, the structural stability and integrity, and displacement ductility of infilled RC frames can remarkably be improved. Copyright © 2017 John Wiley & Sons, Ltd. 相似文献
3.
Observation of damage caused by the recent Abruzzo earthquake on April 6th 2009 showed how local interaction between infills and RC structures can lead to soft‐storey mechanisms and brittle collapses. Results of the present case study are based on observed damage caused by the earthquake in the zone of Pettino. Analytical model based on simulated design procedure was built up and time history analyses were employed to verify the causes of the structural collapse, as highlighted by observed damage. This failure mechanism was investigated taking into consideration all components of the ground motion. Nonlinear behavior of brick masonry infills was taken into account and two parametric hypotheses for infill mechanical properties were considered, given the uncertainties that typically characterize these nonstructural elements. Nonlinear modeling of infills was made by a three‐strut macro‐model aimed at considering both local and global interaction between RC frame and infills. Seismic input was characterized by the real signal registered during the mainshock near the case‐study structure. Different shear capacity models were considered in the assessment. Analytical results seem to confirm with good approximation the likely collapse scenario that damage observation highlighted; the lack of proper detailing in the columns made the local interaction between infills and RC columns and the strong vertical component of the ground motion to be the main causes of the brittle failure. Copyright © 2010 John Wiley & Sons, Ltd. 相似文献
4.
Unreinforced Masonry(URM) is the most common partitioning material in framed buildings in India and many other countries.Although it is well-known that under lateral loading the behavior and modes of failure of the frame buildings change significantly due to infill-frame interaction,the general design practice is to treat infills as nonstructural elements and their stiffness,strength and interaction with the frame is often ignored,primarily because of difficulties in simulation and lack of modeling guidelines in design codes.The Indian Standard,like many other national codes,does not provide explicit insight into the anticipated performance and associated vulnerability of infilled frames.This paper presents an analytical study on the seismic performance and fragility analysis of Indian code-designed RC frame buildings with and without URM infills.Infills are modeled as diagonal struts as per ASCE 41 guidelines and various modes of failure are considered.HAZUS methodology along with nonlinear static analysis is used to compare the seismic vulnerability of bare and infilled frames.The comparative study suggests that URM infills result in a significant increase in the seismic vulnerability of RC frames and their effect needs to be properly incorporated in design codes. 相似文献
5.
砌体填充墙框架结构抗震性能研究现状与展望 总被引：8，自引：0，他引：8
针对砌体填充墙框架结构在地震作用下的受力特点,分析了填充墙钢筋混凝土框架结构产生震害的主要原因。结合国内外砌体填充墙框架结构理论和试验研究成果,围绕填充墙的刚度退化规律和不同性能水平的层间位移角,评述了填充墙框架结构的研究现状。最后,结合基于性能的抗震设计理论背景和禁用黏土实心砖提倡节能的政策背景,指出了今后应以实现基于性能的抗震设计为目标,针对新型砌体填充墙框架结构开展系统研究。 相似文献
6.
One of the main challenges in earthquake risk mitigation is the assessment of existing buildings not designed according to modern codes and the development of effective techniques to strengthen these structures. Particular attention should be given to RC frame structures with masonry infill panels, as demonstrated by their poor performance in recent earthquakes in Europe. Understanding the seismic behaviour of masonry‐infilled RC frames presents one of the most difficult problems in structural engineering. Analytical tools to evaluate infill–frame interaction and the failure mechanisms need to be further studied. This research intends to develop a simplified macro‐model that takes into account the out‐of‐plane behaviour of the infill panels and the corresponding in‐plane and out‐of‐plane interaction when subjected to seismic loadings. Finally, a vulnerability assessment of an RC building will be performed in order to evaluate the influence of the out‐of‐plane consideration in the building response. Copyright © 2015 John Wiley & Sons, Ltd. 相似文献
7.
Terry Y. P. Yuen Han-hui Zhang J. S. Kuang Qunxian Huang 《Bulletin of Earthquake Engineering》2018,16(9):4027-4052
Unreinforced masonry infill walls are widely used as non-structural partitions in RC frames. The effects of infills on the structural responses are often ignored in the design process since they are generally considered as expendable elements. However, recent studies have shown that not only shear damage can be inflicted to the columns braced by the infill walls, but also that the structural stability can be jeopardised by the fall-off of the infills. This paper presents the development of new detailing methods for the infill walls, which features slit panels, isolation gaps between the infills and columns, and anchorage of the infills. The proposed detailing methods were tested and verified experimentally using shake-table tests on five 1/3-scale infilled RC frame specimens with different combinations of the features stated above. The design and construction of the shake-table test specimens have taken into account the similitude requirements. The test results indicate that the proposed detailing method effectively reduced the undesirable interaction between column and infill walls. And the use of proper anchorage could prevent the fall off of infills from the bounding frame. Furthermore, the specimens with slit infill walls displayed better seismic performances, which could be attributed to the rocking behaviour of the sub-panels with increased aspect ratios. 相似文献
8.
Riccardo R. Milanesi Paolo Morandi Guido Magenes 《Bulletin of Earthquake Engineering》2018,16(9):4053-4080
Unreinforced masonry infills are widely used in many parts of the world and it is common practice for seismic design to use simplified methods that usually do not take into account the interaction between the infill and the structure. Starting from the 1950s, many researchers have investigated the lateral response of masonry infills focusing on several different topics. The scientific interest on masonry infills is continuously raising due to the unsatisfactory seismic response of the infilled frame structures observed during post-event inspections and to the difficulty to contrive a widely scientifically and practical recognized solution. Although some modern codes consider the presence of infills with some specifications to prevent damage in the masonry panels and global and local effects on the structure, an effective evaluation of these detrimental effects has not been achieved yet. Within this paper, a FEM simulation of in-plane pseudo-static cyclic tests on a RC frame specimen infilled with unreinforced Autoclaved Aerated Concrete (AAC) masonry infill has been performed in order to study accurately the influence and the interaction of the infill with the RC structure. The experimental results performed by Calvi and Bolognini (J Earthq Eng 5:153–185, 1999), and Penna and Calvi (Campagna sperimentale su telai in c.a. con tamponamenti in Gasbeton (AAC) con diverse soluzioni di rinforzo” (in Italian), 2006) on one-bay one-storey full scale specimens are taken as reference. Non-linear static analyses using a “meso-modelling” approach have been carried out. The masonry used in the model has been calibrated according to tests of mechanical characterization and to in-plane cyclic tests on load-bearing AAC masonry conducted by Costa et al. (J Earthq Eng 15:1–31, 2011). The analyses performed have allowed to investigate the local effects on the frame and, in particular, the changes in the moment and shear demands on the RC elements due to the presence of the AAC infill in comparison with the ones in the bare structure, and to estimate the thrust and the contact length activated by the infill on the frame. 相似文献
9.
Gianni Blasi Daniele Perrone Maria Antonietta Aiello 《Bulletin of Earthquake Engineering》2018,16(12):6105-6130
A wide number of experimental studies conducted in latest years pointed out the high influence of the mechanical properties of masonry units and mortar bed joints on lateral strength and stiffness of masonry panels. This feature significantly modifies the global response of infilled frames under seismic actions as well as the local interaction phenomena. Despite a wide investigation on the influence of the infills on global behaviour of reinforced concrete (RC) frames has already been provided, different features characterizing the seismic performances of buildings suggest the need of accurately evaluating local interaction phenomena as well as the influence of the panel on specific and relevant aspects, as the accelerations transferred to non-structural components. This study provides a parametrical analysis of the influence of shear strength and elastic modulus of masonry infills on the seismic behaviour of RC frames originally designed for gravity loads. Regular buildings with different height were analysed using the Incremental Dynamic Analysis in order to provide fragility curves, investigate on the collapse mechanisms and define the floor spectra depending on the properties of the infills. Results obtained pointed out the high influence of the considered parameters on the fragility of existing RC frames, often characterized by inadequate transversal reinforcement of columns, which may lead to brittle failure due to the interaction with the infills. Floor response spectra are also significantly affected by the influence of masonry infills both in terms of shape and maximum spectral accelerations. Lastly, on the basis of the observed failure mechanisms, a parameter defining the ductility of the frames depending on the properties of the infills was also provided (Capacity Design Factor). The correlation between the mechanical properties of the infills and this parameter suggests its reliability in the simplified vulnerability analysis of existing buildings as well as for the design of new buildings. 相似文献
10.
This paper presents the results of an experimental study on the determination of damping characteristics of bare, masonry infilled, and carbon fiber reinforced polymer retrofitted infilled reinforced concrete (RC) frames. It is well known that the masonry infills are used as partitioning walls having significant effect on the damping characteristics of structures as well as contribution to the lateral stiffness and strength. The main portion of the input energy imparted to the structure during earthquakes is dissipated through hysteretic and damping energies. The equivalent damping definition is used to reflect various damping mechanisms globally. In this study, the equivalent damping ratio of carbon fiber reinforced polymer retrofitted infilled RC systems is quantified through a series of 1/3‐scaled, one‐bay, one‐story frames. Quasi‐static tests are carried out on eight specimens with two different loading patterns: one‐cycled and three‐cycled displacement histories and the pseudo‐dynamic tests performed on eight specimens for selected acceleration record scaled at three different PGA levels with two inertia mass conditions. The results of the experimental studies are evaluated in two phases: (i) equivalent damping is determined for experimentally obtained cycles from quasi‐static and pseudo‐dynamic tests; and (ii) an iterative procedure is developed on the basis of the energy balance formulation to determine the equivalent damping ratio. On the basis of the results of these evaluations, equivalent damping of levels of 5%, 12%, and 14% can be used for bare, infilled, and retrofitted infilled RC frames, respectively. Copyright © 2013 John Wiley & Sons, Ltd. 相似文献
11.
综述了用于提高填充墙钢筋混凝土(RC)框架结构抗震性能和改善结构损伤模式的几类加固措施,从工艺、加固效果和破坏形式3个角度进行了分析。在建筑结构设计过程中,填充墙通常被视为一种典型的脆性非均质非结构构件,忽视了填充墙与RC框架之间的相互作用。地震调查报告表明,在结构遭受地震作用时,填充墙通常先于钢筋混凝土框架发生破坏,未经合理设计的填充墙RC框架结构将在地震作用下产生严重不良后果。试验结果和数值模拟分析结果证明,砌块的强度越低、砂浆的强度越高,结构的承载能力和刚度退化越慢、耗能能力越好。文中根据目前已有的建筑材料改性试验结果,从改性机理出发,分析了一系列有利于提高结构抗震性能的新型材料,并对结构的设计方案进行了探讨。 相似文献
12.
A procedure for displacement‐based seismic design (DBD) of reinforced concrete buildings is described and applied to a 4‐storey test structure. The essential elements of the design procedure are: (a) proportioning of members for gravity loads; (b) estimation of peak inelastic member deformation demands in the so‐designed structure due to the design (‘life‐safety’) earthquake; (c) revision of reinforcement and final detailing of members to meet these inelastic deformation demands; (d) capacity design of members and joints in shear. Additional but non‐essential steps between (a) and (b) are: (i) proportioning of members for the ULS against lateral loads, such as wind or a serviceability (‘immediate occupancy’) earthquake; and (ii) capacity design of columns in flexure at joints. Inelastic deformation demands in step (b) are estimated from an elastic analysis using secant‐to‐yield member stiffnesses. Empirical expressions for the deformation capacity of RC elements are used for the final proportioning of elements to meet the inelastic deformation demands. The procedure is applied to one side of a 4‐storey test structure that includes a coupled wall and a two‐bay frame. The other side is designed and detailed according to Eurocode 8. Major differences result in the reinforcement of the two sides, with significant savings on the DBD‐side. Pre‐test calculations show no major difference in the seismic performance of the two sides of the test structure. Copyright © 2001 John Wiley & Sons, Ltd. 相似文献
13.
Procedures for calibration of linear models for damage limitation in design of masonry‐infilled RC frames 
下载免费PDF全文
下载免费PDF全文 Paolo Ricci Maria Teresa De Risi Gerardo Mario Verderame Gaetano Manfredi 《地震工程与结构动力学》2016,45(8):1315-1335
Recent earthquakes have confirmed the role played by infills in the seismic response of reinforced concrete buildings. The control and limitation of damage to such nonstructural elements is a key issue in performance‐based earthquake engineering. The present work is focused on modeling and analysis of damage to infill panels, and, in particular, it is aimed towards linear analysis procedures for assessing the damage limitation limit state of infilled reinforced concrete frames. First, code provisions on infill modeling and acceptance criteria at the damage limitation limit state are reviewed. Literature contributions on damage to unreinforced masonry infill panels and corresponding displacement capacity are reported and discussed. Two procedures are then proposed aiming at a twofold goal: (i) the determination of ‘equivalent’ interstory drift ratio limits for a bare frame model and (ii) the estimation of the stiffness of equivalent struts representing infill walls in a linear model. These two quantities are determined such that a linear model ensures a reliable estimation of seismic capacity at the damage limitation limit state, providing the same intensity level as that obtained from nonlinear analyses carried out on structural models with infills. Finally, the proposed procedures are applied to four‐story and eight‐story case study‐infilled frames, designed for seismic loads according to current technical codes. The results of these application examples are presented and discussed. Copyright © 2016 John Wiley & Sons, Ltd. 相似文献
14.
This paper presents the shake‐table tests of a 2/3‐scale, three‐story, two‐bay, reinforced concrete frame infilled with unreinforced masonry walls. The specimen is representative of the construction practice in California in the 1920s. The reinforced concrete frame had nonductile reinforcement details and it was infilled with solid masonry walls in one bay and infill walls with window openings in the other bay. The structure was subjected to a sequence of dynamic tests including white‐noise base excitations and 14 scaled historical earthquake ground motion records of increasing intensity. The performance of the structure was satisfactory considering the seismic loads it was subjected to. The paper summarizes the design of the specimen and the major findings from the shake‐table tests, including the dynamic response, the load resistance, the evolution of damage, and the final failure mechanism. Copyright © 2011 John Wiley & Sons, Ltd. 相似文献
15.
Past earthquake experiences indicate that most buildings designed in accordance with modern seismic design codes could survive moderate‐to‐strong earthquakes; however, the financial loss due to repairing cost and the subsequent business interruption can be unacceptable. Designing building structures to meet desired performance targets has become a clear direction in future seismic design practice. As a matter of fact, the performance of buildings is affected by structural as well as non‐structural components, and involves numerous uncertainties. Therefore, appropriate probabilistic approach taking into account structural and non‐structural damages is required. This paper presents a fuzzy–random model for the performance reliability analysis of RC framed structures considering both structural and non‐structural damages. The limit state for each performance level is defined as an interval of inter‐storey drift ratios concerning, respectively, the non‐structural and structural damage with a membership function, while the relative importance of the two aspects is reflected through the use of an appropriate cost function. To illustrate the methodology, herein the non‐structural damage is represented by infill masonry walls. The probabilistic drift limits for RC components and masonry walls from the associated studies are employed to facilitate the demonstration of the proposed model in an example case study. The results are compared with those obtained using classical reliability model based on single‐threshold performance definition. The proposed model provides a good basis for incorporating different aspects into the performance assessment of a building system. Copyright © 2005 John Wiley & Sons, Ltd. 相似文献
16.
17.
Performance evaluation of retrofitting strategies for non-seismically designed RC buildings using steel braces 总被引：1，自引：1，他引：0
H. Varum F. Teixeira-Dias P. Marques A. V. Pinto A. Q. Bhatti 《Bulletin of Earthquake Engineering》2013,11(4):1129-1156
Recent major earthquakes around the world have evidenced that research in earthquake engineering must be directed to the vulnerability assessment of existing constructions lacking appropriate seismic resisting characteristics. Their retrofit or replacement should be made in order to reduce vulnerability, and consequent risk, to currently accepted levels. In this work, the efficiency of ductile steel eccentrically-braced systems in the seismic retrofitting of existing reinforced concrete (RC) buildings is studied. The retrofit technique studied consists in a bracing system with an energy dissipation device, designed to dissipate energy by shear deformation. The numerical model was calibrated with cyclic test results on a full-scale structure. The models used for the RC frame and masonry represent their real behavior and influence in the global structural response. The steel bracing system was modeled with strut rigid elements. The model for the energy dissipater device reproduces rigorously the behavior of the shear-link observed in the cyclic tests, namely in terms of shear, drift and energy dissipation. With the calibrated numerical model, a series of non-linear dynamic analyses were performed, for different earthquake input motions, intending to study: the influence of the retrofitting system in the response of bare and infilled structures; the influence of the location and strength of the retrofitting system. 相似文献
18.
Yong Lu 《地震工程与结构动力学》2002,31(1):79-97
The wall–frame systems have many known advantages, namely increase of the system's lateral strength and stiffness thereby allowing for a good tangential inter‐storey drift control, and the retention of a satisfactory energy dissipation capacity. However, rocking of the wall could occur as a result of uplifting wall base or concentrated plastic hinge deformations. Problems arising from this phenomenon have significant impact on the system behaviour and hence require extended study. This paper focuses on the wall‐rocking phenomenon due to the concentrated plastic hinge rotation at the wall base. To facilitate a comprehensive evaluation, a six‐storey three‐bay RC wall–frame structure is investigated with comparison to a bare ductile frame by means of earthquake simulation tests. The results revealed that, despite a superior performance over the ductile frame under low to moderate seismic actions, the wall–frame structure deteriorated more rapidly than the bare frame during advanced inelastic response. The increasingly significant rocking of the wall resulted in severe material damage at localized critical regions. Mitigating the wall rocking is seen to be a key to the further improvement of the system performance, and the extent to which this may be achieved by incorporating the three‐dimensional effects is explicitly illustrated by an analytical evaluation. Copyright © 2001 John Wiley & Sons, Ltd. 相似文献
19.
Prediction of inter-storey drifts for regular RC structures with masonry infills based on bare frame modelling 总被引：1，自引：1，他引：0
The traditional construction of masonry infills adjacent to RC structural elements is still widely adopted in European countries, including seismically active regions. Given the repeated field observations from damaging earthquakes, pointing to unacceptably high levels of masonry infill damage, the present study is motivated by the need to improve further the European seismic design approach for new RC structures with masonry infills, in order to exclude the poor seismic behaviour probably caused by deficiencies in the verification procedure. Since the in-plane damage to non-structural panels is commonly controlled through the limitation of inter-storey drifts, the possibility to introduce more effective verification criteria, accounting for structural properties, infill layouts and masonry properties is explored. Therefore, starting from the assumption that analyses and verifications in the design of buildings are commonly accomplished neglecting the presence of infills, results of extensive nonlinear numerical analyses for different building configurations are examined. As a result, a simplified procedure for the prediction of expected inter-storey drifts for infilled structures, based on the corresponding demands of bare configurations, in function of a simple parameter accounting for structural properties and the presence of infills, is introduced. Possible implications of the proposed approach aimed at the improvement of the current design provisions are discussed. 相似文献
20.
This paper proposes a new analytical model for masonry‐infilled R/C frames to evaluate the seismic performance considering R/C frame–infill interactions. The proposed analytical model replaces masonry infill with a diagonal compression strut, which represents distributed compression transferred between frame and infill interfaces. The equivalent strut width is presented as a function of the frame–infill contact length, which can be evaluated by static equilibriums related to compression balance and lateral displacement compatibility at the frame–infill interfaces. The proposed analytical model was verified through comparisons with experimental results obtained for several brick masonry‐infilled R/C frames representing a typical R/C building with nonstructural masonry infill in Indonesia. As a result, good agreements were observed between the experimental and analytical values of the lateral strength and ductility of the infilled frames. The seismic performances of two earthquake‐damaged R/C buildings with different damage conditions were evaluated considering infill effects by applying the proposed analytical model. Consequently, the nonstructural brick masonry infill significantly affected the seismic resistances of the buildings, which seemed to lead to differing levels of damage for each building. These results indicate that the proposed analytical model can be an effective tool for more precisely screening earthquake‐vulnerable existing R/C buildings in Indonesia. Copyright © 2016 The Authors. Earthquake Engineering & Structural Dynamics Published by John Wiley & Sons Ltd. 相似文献