共查询到20条相似文献，搜索用时 31 毫秒
1.
灌浆土钉在边坡加固工程中有着广泛的应用。土钉在不同条件下的抗拔机制仍是进一步研究的课题。通过建立一个三维有限元模型,研究土钉在不同上覆压力和剪胀作用下的土钉抗拔行为。采用摩尔-库仑模型模拟花岗岩土,土与土钉界面采用“接触对”和库仑摩擦模型描述。模型可以模拟土钉发生较大抗拔位移下发生滑移破坏的过程。模型参数通过三轴试验结果进行校正。通过与大尺寸室内抗拔试验结果相比较,验证了模型的有效性。模型展现了土钉在钻孔后和抗拔过程中土钉周围的土压力的变化。最后通过参数分析,研究了上覆压力和剪胀对土钉抗拔力的影响。结果显示,当上覆压力较小时,剪胀角对抗拔应力的影响较小。随着上覆压力的增加,剪胀角对抗拔应力的影响变得更加明显。 相似文献
2.
This study proposed a new soil nail known as the compaction-grouted soil nail, and a physical model was established to investigate its pull-out behaviour with different grouting pressures. The study on scale effect of the physical model was performed subsequently via numerical modelling. Additionally, interface shear tests were performed using the same boundary conditions as the physical model test. The strength parameters obtained were used to estimate the pull-out resistance of a conventional soil nail. The merits of these two soil nail types were compared based on their pull-out resistances. The physical model test results showed that the pull-out resistance of the compaction-grouted soil nail increases with increasing grouting pressure. In addition, the pull-out resistance exhibits hardening behaviour without a yield point, indicating that the compaction-grouted soil nail enables soils to remain stable against a relatively large deformation before ultimate failure. Furthermore, a higher grouting pressure results in a higher rate of increase for pull-out resistance versus pull-out displacement, which improves the performance of the compaction-grouted soil nail in the stabilization of large deformation problems. A comparison of the two types of soil nails suggests that the new compaction-grouted soil nail is more sensitive to grouting pressure than the conventional soil nail in terms of pull-out resistance improvement. In other words, the performance (pull-out resistance) of the compaction-grouted soil nail can be markedly improved by increasing the grouting pressure without inducing any accidental or undesired cracking or soil displacement.
相似文献3.
Successful numerical simulation of geosynthetic-reinforced earth structures depends on selecting proper constitutive models for soils, geosynthetics and soil–geosynthetic interfaces. Many constitutive models are available for modelling soils and geosynthetics. However, constitutive models for soil–geosynthetic interfaces which can capture most of the important characteristics of interface response are not readily available. In this paper, an elasto-plastic constitutive model based on the disturbed state concept (DSC) for geosynthetic–soil interfaces has been presented. The proposed model is capable of capturing most of the important characteristics of interface response, such as dilation, hardening and softening. The behaviour of interfaces under the direct shear test has been predicted by the model. The present model has been implemented in the finite element procedure in association with the thin-layer element. Five pull-out tests with two different geogrids have been simulated numerically using FEM. For the calibration of the constitutive models used in FEM, the standard laboratory tests used are: (1) triaxial tests for the sand, (2) direct shear tests for the interfaces and (3) axial tension tests for the geogrids. The results of the finite element simulations of pull-out tests agree well with the test data. The proposed model can be used for the stress-deformation study of geosynthetic-reinforced embankments through numerical simulation. Copyright © 1999 John Wiley & Sons, Ltd. 相似文献
4.
土钉的抗拔强度是土钉支护结构设计需要用到的重要参数。抗拔强度的大小取决于拔出过程中作用于土钉表面的法向应力的大小。通过室内模型抗拔试验以及三维有限元分析,研究了钻孔灌注型土钉在钻孔、注浆及拔出过程中土钉杆周围土体中的应力变化情况。研究发现,对于钻孔灌注型土钉,孔周土体中的应力在钻孔结束时几乎全部释放掉;对于低压灌浆土钉,灌浆结束到浆体硬化的过程中土钉杆周围土体中的应力没有得到有效恢复;拔出过程中,由于土体的剪胀变形受到约束,土钉周围土体中的应力随着拔出位移的增加逐渐增加,从而导致抗拔应力的增加,说明土的剪胀性对钻孔灌注型土钉来说非常重要,对于低剪胀性土,需要通过增加灌浆压力等方法对钻孔过程中释放掉的应力进行补偿 相似文献
5.
A model test was conducted for a newly developed soil nail, the result of which was compared to that of a 3D finite element method (FEM) simulation. The shape angle (β) and friction coefficients (μ) contributed to the difference in pull-out force between the model test and the simulation. Further verifications were conducted, during which the pull-out mechanisms of the soil nail for different β and μ were analysed. It was found that both β and μ have a positive influence on the pull-out force; β only affects the increase rate, while μ influences the overall pull-out force level. Three components were found to govern the pull-out force, with the component applied to the expanded cement bulk surface accounting for approximately 80% of the total. This study proves that the optimal approach for increasing pull-out force is to enlarge the diameter of the cement bulk rather than extend the nail length. 相似文献
6.
Pressure-grouted soil nails have been increasingly used for stabilizing slopes. The pullout resistance of a soil nail is the main factor for reinforcing the slope stability. In this study, a two-dimensional axisymmetric finite element model is developed to simulate the pullout behavior of a pressure-grouted soil nail. This model is verified with field pullout tests result of a pressure-grouted soil nails by comparing with gravity-grouted soil nails. Based on the analysis, a three-dimensional finite element model is proposed for stability analysis of a slope reinforced with pressure-grouted soil nails using the shear strength reduction method. A series of numerical slope stability analyses for a slope composed of weathered soil are performed to investigate the effects of grouting pressure on the slope stability and the behavior of the soil nails. Special attention is given to the installation effect of a pressure-grouted soil nails. It is found from the result of this study that the pressure-grouted soil nails increase the safety factor by fifty percent in a slope by increasing the stiffness of the nailed slope system. Numerical analysis results confirm the fact that the pullout resistance of a soil nail is the main factor for stabilizing slopes rather than the shear resistance of the soil nail. 相似文献
7.
含水率对土工格栅加筋膨胀土结构的运行具有直接影响,而国内外对其作用机制少有研究。为此,采用填土尺寸为600 mm×600 mm×600 mm的大型叠环式剪切仪进行一系列拉拔试验,研究了含水率对土工格栅与膨胀土界面拉拔性状的影响。试验结果表明,含水率对拉拔力与土工格栅位移特征、界面应力变形特征、界面强度参数等具有显著影响。含水率较高,土工格栅发生刚体平动的时间较早,刚体平动时的单宽拉拔力更接近峰值,界面更偏于理想刚塑性特征;含水率较低,界面似黏聚力较大;而含水率对界面似摩擦角的影响不显著。 相似文献
8.
土工格栅与土界面作用特性试验研究 总被引：9，自引：4，他引：5
土工格栅与土的界面摩擦特性指标是加筋土工程设计的关键。通过分析土工格栅与土的界面摩擦作用和进行了直剪摩擦试验和拉拔摩擦试验,测试了两种试验条件的界面摩擦特性。在两种试验条件下,土工格栅加筋土复合体的抗剪强度均有界面摩擦角φsq和界面凝聚力csq,且土工格栅与土相对位移量的不同,其复合体的强度机理有区别。在拉拔摩擦试验中,剪应力峰值强度对应的剪切变形值高于直剪摩擦试验中剪应力峰值强度的剪切变形值5～10倍以上。两种试验均有其适用性,而土与土工格栅的相对位移较小时直剪摩擦试验较能反映实际;土与土工格栅相对位移较大时土与格栅双面均发生相对位移,拉拔摩擦试验更为合适。随法向应力的增大,直剪摩擦和拉拔摩擦试验的剪应力峰值以及剪应力峰值对应的位移均提高。直剪摩擦的剪切速度小,剪应力峰值强度高,且达到峰值强度的剪切位移大;增加剪切速度,剪应力峰值强度降低,且对应的位移也减少,其原因是界面上的孔隙水压力消散和筋材的应力松弛。应根据具体工程的需要选择直剪摩擦试验和拉拔摩擦试验确定设计参数。 相似文献
9.
10.
Soil nailing has been widely used as a reinforcing technique to retain excavations and stabilise slopes. Proper assessment of the interaction between the nails and the surrounding soil is central to safe and economical design of the composite reinforced soil structure. In this note, a new interface model, denoted as “embedded bond-slip model”, is proposed to model the soil–nail interaction numerically in a simplified manner. Combining the key features of the embedded element technique and the conventional interface element method, the proposed plane–strain interface model has the advantages that no special considerations have to be given to the arrangement of the finite element mesh for the soil nails, and that possible tangential slippage along the interface can be modelled. The formulation also allows pore water flow across the soil nails to be incorporated into the analysis. The proposed model has been implemented into a finite element code and verified by simple element tests under different uni-direction loading conditions. Using the proposed interface model, back analyses of a field test involving a soil-nailed cut slope subjected to a rise in groundwater table have been conducted. This note presents the details of the embedded bond-slip model and the numerical results which demonstrate that the proposed model is capable of simulating soil–nail interaction conveniently and realistically. 相似文献
11.
Soil nails have been widely used to stabilize slopes and earth retaining structures in many countries and regions, especially, in Hong Kong. The analysis of the interaction between a soil nail and the surrounding soil is of great interests to both design engineers and researchers. In this paper, authors present a simple mathematical model for the interaction analysis of a soil nail and the surrounding soil considering a few key factors which are soil dilation, bending of the soil nail, vertical pressure, and non-linear subgrade reaction stiffness. The lateral subgrade reaction between the soil and the soil nail is assumed to obey a hyperbolic relation. Reported test data in the literature are used to verify the present model. The contributions of the soil-nail bending on the pull-out resistance are evaluated in two case studies. 相似文献
12.
《Geomechanics and Geoengineering》2013,8(4):259-273
An important design parameter in cement-grouted soil nailed structures is the shear strength at the interface between the grouted nail and the surrounding soil. Both field and laboratory pull-out tests are normally used to investigate this interface shear strength. However, these tests have some limitations. In this study, direct shear box tests are adopted to investigate the interface shear strength behaviour between a completely decomposed granite (CDG) soil and a cement grout plate. Tests were carried out in a large direct shear test apparatus over a range of constant normal stress, soil moisture content, and soil–cement grout interface surface waviness. The laboratory test procedures are briefly described and the main test results are presented, followed by a discussion of the shear behaviour of the soil–cement grout interface. The interface shear behaviour is compared with the shear strength behaviour of the same soil tested under comparable conditions. It is shown that the shear stress–displacement behaviour of the soil–cement grout interface is similar to that of the soil alone. The test results indicate that the interface shear strength of the CDG and cement grout material depends on the normal stress level, the soil moisture content, and the interface surface waviness. 相似文献
13.
Ye Xinyu Wang Shanyong Wang Qiong Sloan Scott William Sheng Daichao 《Acta Geotechnica》2019,14(4):1101-1111
A series of large-scale model tests was conducted on compaction-grouted soil nails to study the influence of the degree of saturation on the soil response to compaction grouting and pull-out. The experimental results show that the initial degree of saturation of the soil strongly influences the grout injectability, thus the formed diameter of grout bulb. Subsequently, the diameter of the grout bulb alters the pull-out force, with larger grout bulbs generating higher pull-out forces and exhibiting greater hardening behaviour. Interestingly, the initial pull-out forces are the same for the same grouting pressure, regardless of the initial degree of saturation and the subsequently grout bulb. In addition, some of the main factors influencing the pressure grouting and pull-out of the soil nail, as the initial degree of saturation varies, are as follows. First, the variations in the soil pressure and density with the initial degree of saturation are similar to that of the volume of grout injected, and the compression of the soil induced by pressure grouting exhibits a similar evolution with the initial degree of saturation at different locations. Second, the initial degree of saturation of the soil sample plays a dominant role in the change in suction during pressure grouting and pull-out of soil nail. Third, the horizontal soil pressure derived from the pull-out of soil nail propagates closely in the soil sample of lower initial degree of saturation. The vertical soil pressure induced by the vertical soil dilation and squeezing effect varies in accidence with the initial degree of saturation and the grout bulb.
相似文献14.
This paper investigates the pull-out behaviour (particularly the bearing resistance) of a steel grid reinforcement embedded in silty sand using laboratory tests and numerical analyses. It is demonstrated that the various common analytical equations for calculating the bearing component of pull-out resistance give a wide range of calculated values, up to about 200% disparity. The disparity will increase further if the issue of whether to use the peak or critical state friction angle is brought in. Furthermore, these equations suggest that the bearing resistance factor, Nq, is only a function of soil friction angle which is not consistent with some design guidelines. In this investigation, a series of large scale laboratory pull-out tests under different test pressures were conducted. The test results unambiguously confirmed that the Nq factor is a function of test pressure. A modified equation for calculating Nq is also proposed. To have more in-depth understanding of the pull-out behaviour, the tests were modelled numerically. The input parameters for the numerical analysis were obtained from laboratory triaxial tests. The analysis results were compared with the experimental results. Good agreement between experimental and numerical results was achieved if the strain-softening behaviour from peak strength to critical state condition was captured by the soil model used. 相似文献
15.
Drained triaxial tests are conducted on natural and reinforced sand under various stress paths. Direct shear tests and pull-out tests are conducted on soil–reinforcement interface and on reinforcement, respectively. The effects of two types of reinforcement, viz, woven and non-woven geotextile and number of layers of reinforcement are investigated. Hierarchical single surface model is used to depict the behaviour of natural and reinforced soil by treating the soil as a single composite material and by considering soil, reinforcement and interface as independent elements. It is shown that the material parameters are very much affected by the type and the number of layers of reinforcement. The hierarchical model provides satisfactory prediction for both natural and reinforced soil. Copyright © 1999 John Wiley & Sons, Ltd. 相似文献
16.
This paper describes a modified elasto‐plasticity damage model to capture monotonic and cyclic behavior of the interface between a geotextile and gravelly soil. New damage variable and shear strength criterion are introduced on the basis of test observations. The formulations of the modified model are obtained by extending those of the original interface model. The model parameters with physical meaning are easily determined from a group of cyclic shear tests and a confining compression test. The model predictions are compared with the results of a series of direct shear tests and large‐scale pullout tests. The comparison results demonstrate that the model accurately describes the monotonic and cyclic stress–strain relationship of the interface between a geotextile and gravelly soil while capturing new characteristics: (1) the strength that is nonlinearly dependent on the normal stress; (2) significant shear strain‐softening; (3) the comprehensive volumetric strain response with dependency on the shear direction; and (4) the evolution of behavior associated with the changes in the physical state that includes the geotextile damage. This model is used in a finite element analysis of pullout tests, indicating that the tensile modulus of a geotextile has a significant effect on the response of the geotextile–gravel system. Copyright © 2009 John Wiley & Sons, Ltd. 相似文献
17.
为了更全面地分析筋土界面相互作用特性,改制了一台可视加筋土界面特性宏细观分析的试验仪器,可开展不同土工合成材料与填料的直剪和拉拔试验;该仪器改进了试验箱的尺寸,可方便两种试验的对比分析,增加了图像摄录系统,可进行试验过程的细观分析。使用新研制仪器分别进行了土工合成材料（土工格栅和土工布）加筋尾矿砂的直剪和拉拔试验,试验结果表明:两种试验条件下,土工格栅与尾矿的界面参数（似黏聚力和似摩擦角）及似摩擦系数均比土工布与尾矿的界面参数和似摩擦系数大;直剪试验下筋材网孔的有无对筋-尾矿界面参数均有较大影响,拉拔试验下筋材网孔有无对筋-尾矿界面参数似黏聚力的影响较为显著,对似摩擦角的影响较小。随着宏观变量法向应力的增加,细观参数孔隙率减小,平均接触数增加,反映在宏观上的现象就是填料颗粒被压密,筋材需要克服的阻力增大。该试验仪器能够较好地分析筋土界面宏细观特性,获得关键技术指标以用于加筋结构的设计。 相似文献
18.
基于锚固体轴对称受力特征开发了一种土层锚固界面试验装置,结合二维数字散斑相关方法,获得随着荷载加大锚固体周边土体的位移场及应变场变化规律。试验结果表明,锚固体的位移带动周边土体变形主要出现在靠近锚固体的一小薄层范围内,其变形具有范围稳定、连续、线性和剪胀等特征。采用与Coulomb屈服条件相关联的流动法则建立锚固体界面层的本构关系,并推导出了锚固体在拉拔荷载条件下的轴力和剪应力分布的表达式。分析结果表明,锚固体上的剪应力分布的均匀程度与土层密实度密切相关,土层的密实度越低,其抗力系数、内摩擦角越小,则锚固体上的剪应力分布越均匀,而抗力系数和内摩擦角较大的土层,其剪应力分布特征与岩石锚固体的理论及实测成果相似。 相似文献
19.
Seismic response analysis of geosynthetic reinforced soil segmental retaining walls by finite element method 总被引：3，自引：0，他引：3
The paper presents the results of a finite element analysis of the dynamic response of a geosynthetic reinforced soil retaining wall that is constructed with dry-stacked modular concrete blocks as the facia system. In the finite element model, the cyclic shear behavior of the backfill soil is described by a hyperbolic stress-strain relationship with Masing hysteretic unload-reload behavior. The reinforcement material is modelled using a similar hysteretic model which takes into account the measured response of cyclic load-extension tests performed on unconfined geogrid specimens in the laboratory. Interface shear between wall components is simulated using slip elements. The results of finite element analyses giving the seismic response of a typical geogrid reinforced segmental retaining wall subjected to prescribed acceleration records are presented. The results of analyses highlight the influence of dynamic loading on: (1) wall displacement; (2) cumulative interface shear force and displacement between facing units; (3) tensile forces developed in the reinforcement and; (4) acceleration response over the height of the wall. A number of implications to the design of these structures are identified based on the results of these simulations. 相似文献
20.
A plane–strain numerical model has been developed to mimic a nailed loose fill slope under surcharge loading. The model has been used to back-analyse a field test that was conducted to examine the behaviour of soil nails in loose fill slopes under surcharge loading. Incremental elasto-plastic analyses coupled with pore water diffusion have been performed to study the internal deformation, water content redistribution in the soil, and the performance of the soil nails during and after the application of surcharge loading. The model parameters describing the mechanical and hydraulic properties of the nailed slope were obtained from field or laboratory tests. Different modelling techniques and boundary conditions for mimicking soil–nail interaction in loose fill material have been examined. Comparisons between numerical predictions and field measurements demonstrate that a new interfacial model, denoted as the embedded bond–slip interface model, is more suitable for mimicking the interfacial behaviour. Despite the simplicity of the numerical model, the predicted responses are in close agreement with the field test results, in particular the mobilisation and distribution of nail forces in response to surcharge loading. Both the numerical and the field test results suggest that soil nails are capable of increasing the overall stability of a loose fill slope for the loading conditions considered in this study. The increase in confining stress along the soil nails near the surcharge area is central to the overall stabilising mechanism. On the contrary, the nail forces mobilised near the nail heads are much smaller, indicating that the beneficial effect of having a structural grillage system at the slope face is limited for the range of surcharge pressures considered in this study. 相似文献