共查询到20条相似文献，搜索用时 15 毫秒
1.
The paper describes and evaluates an incremental plasticity constitutive model for unsaturated, anisotropic, nonexpansive soils (CMUA). It is based on the modified Cam-Clay (MCC) model for saturated soils and enhances it by introducing anisotropy (via rotation of the MCC yield surface) and an unsaturated compressibility framework describing a double dependence of compressibility on suction and on the degree of saturation of macroporosity. As the anisotropic and unsaturated features can be activated independently, the model is downwards compatible with the MCC model. The CMUA model can simulate effectively: the dependence of compressibility on the level of developed anisotropy, uniqueness of critical state independent of the initial anisotropy, an evolving compressibility during constant suction compression, and a maximum of collapse. The model uses Bishop's average skeleton stress as its first constitutive variable, favouring its numerical implementation in commercial numerical analysis codes (eg, finite element codes) and a unified treatment of saturated and unsaturated material states. 相似文献
2.
天然土体的初始各向异性通常可对其后继循环特性产生显著影响。现有考虑循环载荷作用的土体弹塑性模型,往往采用类似修正剑桥模型的椭圆形屈服面,已有研究表明,该椭圆形屈服面因其拉伸弹性区域偏大,针对天然K0固结状态的土体,其计算精度较差。基于新近提出的广义各向同性硬化准则,在边界面方程中引入初始各向异性张量,并采用空间滑动面破坏准则（SMP）的变换应力法,建立了能考虑饱和黏土初始各向异性的循环边界面塑性模型。分别针对等压和偏压固结的饱和黏土静、动三轴试验进行模拟,结果表明,该模型能合理反映土体的初始各向异性及其后继循环动力特性。 相似文献
3.
在岩土破损力学基础上,基于微观破损机制,提出了考虑各向异性的结构性砂土本构理论。采用Lade-Duncan强度准则考虑中主应力对抗剪强度的影响;采用考虑颗粒排列组构的各向异性状态变量A反映各向异性对土体强度和变形的影响;通过相似扩大重塑土的屈服面反映结构性对土性的影响;通过引入非相关联流动法则考虑各向异性和结构性对土体塑性变形的影响。同时,将基于微观力学机制的损伤演化规律引入结构性土的硬化规律;该硬化规律同时考虑了塑性体积应变和剪切应变对各向异性结构性土强度的影响。然后将该模型用于模拟室内三轴压缩试验,初步验证了该模型的合理性和适用性。 相似文献
4.
5.
The Hope Slide, which occurred on January 9, 1965, involved an estimated 47-Mm3 of meta-volcanics and intrusive rocks. Previous workers reported the presence of tectonic structures (faults and shear zones) along the failure surface at the Hope Slide. These tectonic features were investigated in detail to assess their effects on rock-mass quality and the related implications for slope stability. This paper integrates basic field and laboratory concepts from structural and engineering geology. Subdividing the failure area into structural domains allowed distinct discontinuity sets to be associated with specific tectonic structures. The Geological Strength Index (GSI) was used to estimate the rock-mass damage related to the tectonic structures. Low GSI values were seen to outline tectonic damage zones. Point-load tests were used to characterise the compressive strength of rocks adjacent to the tectonic structures. Strength anisotropy, tentatively attributed to damage caused by a large shear zone, was observed in greenstone samples. Seepage zones along the failure surface were observed preferentially along shallow discontinuities that dipped downslope and in rock masses of good quality (GSI > 40). An alternative morphology of the slope failure is proposed by distinguishing between the extent of the surficial damage due to the rock-slope failure and the zone of failed material (depletion zone). For the first time, a kinematic mechanism for the Hope Slide is proposed, based on a preliminary 3-dimensional block model. A pre-1965 DEM was produced from estimates of material lost and gained as reported by previous workers. The pre-1965 DEM revealed that the tectonic structures recognised during fieldwork bounded the material that failed in the 1965 event. 相似文献
6.
Hao Zhang 《Geomechanics and Geoengineering》2018,13(1):1-10
Natural soils such as clays exhibit a variety of features including anisotropy, destruction and overconsolidation. In this work, a constitutive model that is able to replicate those salient features of natural clays is presented. The model is based on the classical S-CLAY1 model, where the anisotropy of the soil is captured through the initial inclination and rotation of the yield surface. To account for overconsolidation, a parabolic Hvorslev envelope is adopted. The compression curve of the reconstituted soil is taken as the reference to describe the structural of the soil. Parameters of the proposed constitutive model all have clear physical meanings and can be conveniently determined from conventional triaixal tests. Numerical examples using the proposed model to simulate overconsolidated natural soils are presented and compared with existing experimental data, demonstrating the capability of the model. 相似文献
7.
天然岩土材料具有结构性和各向异性。在岩土破损力学的理论框架下,建立了初始应力各向异性结构性土的二元介质模型。岩土破损力学把结构性岩土材料抽象成由胶结强的胶结块（胶结元）和无胶结的软弱带（摩擦元）组成的二元结构体,变形过程中胶结块逐步破损并向软弱带转化。假定胶结块为横观各向同性的理想弹脆性体,胶结块破损后转化成的软弱带为可用邓肯-张模型描述的非线性弹性体。通过引入考虑各向异性影响的破损率和局部应变系数,建立了初始应力各向异性结构性土的二元介质本构模型,并给出了模型参数的确定方法。最后给出了模型的表现,且通过人工制备初始应力各向异性结构性土的三轴压缩试验结果验证了模型的适用性。计算结果表明,所提出的本构模型可以较好地模拟初始应力各向异性结构性土的应力-应变和体积变形特性。 相似文献
8.
This paper presents a micro-mechanical study on the characteristics of shear-induced anisotropy in granular media. Based on three-dimensional Discrete Element Method (DEM) simulations, the distinct features associated with the evolution of internal granular structure and different anisotropy sources during drained/undrained shearing of granular samples are carefully examined. The study finds that static liquefaction occurs when the geometrical anisotropy in a sample dominates the mechanical anisotropy in the overall shear strength, and the weak force network features an exceptionally high proportion of sliding contacts and develops certain degree of anisotropy. Phase transformation corresponds to a transitional, unstable state associated with a dramatic change in both coordination number and the proportion of sliding contacts in all contacts. The critical state in a granular material is always associated with a highly anisotropic fabric structure wherein both the critical void ratio and critical fabric anisotropy are uniquely related to the mean effective stress. The relations provide a more comprehensive definition for the critical state in granular media with proper reference to the critical fabric anisotropy. 相似文献
9.
The theory of hypoplasticity was developed initially for non-cohesive soils. However, sand and clay have many common properties;
therefore arose the idea to extend the hypoplastic model to clay. The proposed model is able to describe the behaviour of
cohesive soils with the incorporation of an appropriate structure tensor into the constitutive equation. This tensor is a
stress-like internal parameter, also called back stress. This enables us to describe the behaviour of cohesive soils with
the same material parameters for several states of consolidation and also to model barotropy and pycnotropy of sand. Numerical
simulations of element tests are performed in order to check the performance of this hypoplastic model. Experimental data
obtained with normally and overconsolidated clay and sand specimens with various densities are taken for comparison, and it
is shown that the model is capable of describing the material behaviour of clay and sand. The determination of the material
constants, the calibration method, is also presented in this paper. 相似文献
10.
This paper presents an advanced constitutive model for unsaturated soils, using Bishop’s effective stress (σ′) and the effective degree of saturation (Se) as two fundamental constitutive variables in the proposed constitutive model. A sub-loading surface and a unified hardening parameter (H) are introduced into the σ′–Se modelling framework to interpret the effects of initial density on coupled hydro-mechanical behaviour of compacted soils. Compared with existing models in the literature, the main advantage of the proposed model that it is capable of modelling hydro-mechanical behaviour of unsaturated soils compacted to different initial densities, such as the dependence of loading–collapse volume on initial void ratio and density effect on the shearing-induced saturation change. The proposed model requires 13 material parameters, all of which can be calibrated through conventional laboratory tests. Numerical studies are conducted to assess the performance of the model for a hypothetical soil under two typical hydro-mechanical loading scenarios. The proposed advanced unsaturated soil model is then validated against a number of experimental results for both isotropic and triaxial conditions reported in the literature. 相似文献
11.
Coal swelling/shrinkage during gas adsorption/desorption is a well-known phenomenon. For some coals the swelling/shrinkage shows strong anisotropy, with more swelling in the direction perpendicular to the bedding than that parallel to the bedding. Experimental measurements performed in this work on an Australian coal found strong anisotropic swelling behaviour in gases including nitrogen, methane and carbon dioxide, with swelling in the direction perpendicular to the bedding almost double that parallel to the bedding. It is proposed here that this anisotropy is caused by anisotropy in the coal's mechanical properties and matrix structure. The Pan and Connell coal swelling model, which applies an energy balance approach where the surface energy change caused by adsorption is equal to the elastic energy change of the coal solid, is further developed to describe the anisotropic swelling behaviour incorporating coal property and structure anisotropy. The developed anisotropic swelling model is able to accurately describe the experimental data mentioned above, with one set of parameters to describe the coal's properties and matrix structure and three gas adsorption isotherms. This developed model is also applied to describe anisotropic swelling measurements from the literature where the model was found to provide excellent agreement with the measurement. The anisotropic coal swelling model is also applied to an anisotropic permeability model to describe permeability behaviour for primary and enhanced coalbed methane recovery. It was found that the permeability calculation applying anisotropic coal swelling differs significantly to the permeability calculated using isotropic volumetric coal swelling strain. This demonstrates that for coals with strong anisotropic swelling, anisotropic swelling and permeability models should be applied to more accurately describe coal permeability behaviour for both primary and enhanced coalbed methane recovery processes. 相似文献
12.
在最优含水率干侧压实的黏土一般具有明显的双孔结构,其集聚体间孔隙（又称宏观孔隙）和集聚体内孔隙（又称微观孔隙）对土体宏观水力和力学特性影响差异显著,同时,水-力耦合作用下两种孔隙的演化规律也存在明显不同。双孔结构非饱和土对应的孔径分布函数为双峰孔径分布形式,该分布函数可通过叠加宏观孔隙和微观孔隙的单峰孔径分布曲线得到,并通过平移量、缩放量和分散度3个演化参数对双孔结构土的孔隙演化规律进行描述。通过构建在力学及水力加、卸载过程中演化参数与孔隙比之间的关系,提出了适用于描述变吸力下非饱和压实土的微观结构演化模型。分别基于所开展的桂林红黏土压汞试验数据和文献中的米尼亚卢博瓦膨胀土试验数据,对所建立的微观结构演化模型进行参数标定,并通过模型预测结果与试验结果的对比,验证了所建立模型的适用性。 相似文献
13.
Clayey rocks are frequently chosen as a geological barrier material for underground repositories. The inherent anisotropic mechanical behavior and the evolution of mechanical behavior with water content are two crucial material properties for the safety analysis of these structures. The present paper focuses on numerical modeling of the inherent anisotropy and the effect of water content, as well as the interactions of these properties in partially saturated clayey rocks with preferably oriented bedding planes. A discrete thermodynamic approach is adopted for describing the inherent anisotropic mechanical behavior, and the anisotropy of the elastic parameters, plastic evolution and damage evolution are considered. Capillary pressure is introduced to describe the effect of the water content with the help of the effective stress concept, and a procedure for the identification of the model parameters is presented. Finally, the proposed model is applied to a study of triaxial compression tests of argillite with different orientations of the bedding planes and variable water content. In summary, the main features of the studied material are well reproduced by the model. 相似文献
14.
Advanced material constitutive models are used to describe complex soil behaviour. These models are often used in the solution of boundary value problems under general loading conditions. Users and developers of constitutive models need to methodically investigate the represented soil response under a wide range of loading conditions. This paper presents a systematic procedure for probing constitutive models. A general incremental strain probe, 6D hyperspherical strain probe (HSP), is introduced to examine rate‐independent model response under all possible strain loading conditions. Two special cases of HSP, the true triaxial strain probe (TTSP) and the plane‐strain strain probe (PSSP), are used to generate 3‐D objects that represent model stress response to probing. The TTSP, PSSP and general HSP procedures are demonstrated using elasto‐plastic models. The objects resulting from the probing procedure readily highlight important model characteristics including anisotropy, yielding, hardening, softening and failure. The PSSP procedure is applied to a Neural Network (NN) based constitutive model. It shows that this probing is especially useful in understanding NN constitutive models, which do not contain explicit functions for yield surface, hardening, or anisotropy. Copyright © 2004 John Wiley & Sons, Ltd. 相似文献
15.
16.
The Barcelona basic model (BBM) successfully explained many key features of unsaturated soils and received extensive acceptance. It is also one of the few elastoplastic constitutive models for unsaturated soils that have been implemented within finite element codes and applied to the analysis of real boundary value problems. The BBM was proposed in incremental forms according to theories of soil plasticity in which individual aspects of the isotropic virgin behavior are controlled by multiple parameters, whereas at the same time, a single parameter controls more than one aspect of soil behavior. Although a variety of methods have been recently developed for calibrating model parameters for elastoplastic soil models, at present, there are no well‐established, simple, and objective methods for selecting parameter values in the BBM from laboratory tests. This has been one of the major obstacles to the dissemination of this constitutive model beyond the research context. This article presents an optimization approach especially developed for simple and objective identification of material parameters in the BBM. This is achieved by combining a modified state surface approach, recently proposed to model the elastoplastic behavior of unsaturated soils under isotropic stress conditions, with the Newton or quasi‐Newton method to simultaneously determine the five parameters governing isotropic virgin behavior in the BBM. The comparison between results using the proposed method and an existing method for the same laboratory tests was discussed from which the simplicity and objectivity of the proposed method were evaluated. Copyright © 2012 John Wiley & Sons, Ltd. 相似文献
17.
It is well known that soil is inherently anisotropic and its mechanical behavior is significantly influenced by its fabric anisotropy. Hypoplasticity is increasingly being accepted in the constitutive modeling for soils, in which many salient features, such as nonlinear stress-strain relations, dilatancy, and critical state failure, can be described by a single tensorial equation. However, within the framework of hypoplasticity, modeling fabric anisotropy remains challenging, as the fabric and its evolution are often vaguely assumed without a sound basis. This paper presents a hypoplastic constitutive model for granular soils based on the newly developed anisotropic critical state theory, in which the conditions of fabric anisotropy are concurrently satisfied along with the traditional conditions at the critical state. A deviatoric fabric tensor is introduced into the Gudehus-Bauer hypoplastic model, and a scalar-valued anisotropic state variable signifying the interplay between the fabric and the stress state is used to characterize its impact on the dilatancy and strength of the soils. In addition, fabric evolution during shearing can explicitly be addressed. Modifications have also been undertaken to improve the performance of the undrained response of the model. The anisotropic hypoplastic model can simulate experimental tests for sand under various combinations of principle stress direction, intermediate principal stress (or mode of shearing), soil densities, and confining pressures, and the associated drastic effect of different principal stress orientations in reference to the material axes of anisotropy can be well captured. 相似文献
18.
Experimental evidence shows that a gap-graded soil or a widely-graded granular material may have a bimodal soil–water characteristic curve (SWCC) and a bimodal permeability function. A bimodal SWCC or a bimodal permeability function originates from a dual-porosity structure. To date, the prediction of bimodal SWCCs for gap-graded soils is still a difficult task. In this paper, a bimodal SWCC model is proposed to describe the drying process of granular soils considering a dual-porosity structure. The new SWCC model shows powerful capability in fitting the SWCCs for soils varying from gravel to silt. Regression analysis is conducted to establish empirical relations between the model parameters and the indexes of soil grain-size distribution (GSD). Based on these relations, the new model predicts well both the bimodal SWCCs for gap-graded soils and the unimodal SWCCs for well-graded soils and uniform soils. A bimodal permeability function is also proposed and linked to the new SWCC model. In the absence of experimental SWCCs and permeability functions, the new model can be used to obtain preliminary SWCCs and permeability functions for granular soils. It should be mentioned that the prediction of the SWCC from the GSD is still empirical and does not address the cyclic wetting/drying process. Measurement of the SWCC should be performed wherever an accurate SWCC is required. 相似文献
19.
在描述重塑土的统一硬化模型（UH模型）基础上,以动态地移动正常固结线（MNCL）代替静态的正常固结线（NCL）作为参考线来确定参考应力,将土的结构性衰减体现在MNCL的演化中,从而把UH模型扩展为可考虑土结构性的结构性土UH模型。结构性土UH模型可以合理地并连续光滑地描述结构性土的等向压缩规律、应变硬化、应变软化、剪切体积收缩、剪切体积膨胀、不排水剪切减压软化以及结构性和密度耦合影响等力学特性。相比于UH模型,结构性土UH模型新增3个参数,分别用于描述结构性的程度、衰减速度、以及塑性流动规律。通过3种天然土的试验结果与模型预测对比验证了结构性土UH 模型的合理性。 相似文献
20.
In order to simulate the soil response during principal stress rotation, anisotropic unified hardening (UH) model is developed within the framework of elastoplastic theory. Without introducing any additional mechanism to display the role of stress rotation specifically, this model achieves the simulation by considering the material anisotropy. The effect of inherent anisotropy is reflected using the anisotropic transformed stress method, but a new formula for the stress mapping is adopted to keep the mean stress unchanged. Analysis indicates that from the view of the transformed stress tensor, the anisotropic soil is subjected to loading during pure rotation of principal stress axes, so that plastic strains can be calculated. To represent the induced anisotropy, a fabric evolution law is proposed based on laboratory and numerical test results. At the critical state, the fabric tensor reaches a stable value determined by the stress state, while the critical state line is unique in the plane of void ratio versus mean stress. The anisotropic UH model has concise formulation and explicit elastoplastic flexibility matrix and can provide reasonable predictions for the deformation of anisotropic soils when principal stresses rotate. 相似文献