共查询到20条相似文献，搜索用时 46 毫秒
1.
船舶与海洋结构在服役期间会遭受电化学和微生物侵蚀等多种腐蚀环境影响,加筋板作为此类结构的主要受力构件,其表面易产生不规则形态的点蚀,引起构件的强度退化。利用ANSYS有限元软件构建加筋腹板遭受随机点蚀损伤的加筋板有限元模型,研究带板长宽比、带板长细比、加筋长细比和腐蚀体积损失率对加筋板极限强度的影响。研究结果表明,加筋遭受同等腐蚀体积损失率下,带板长宽比变化对极限强度退化的影响很小,但带板长细比和加筋长细比变化产生的影响明显;带板长细比越大,极限强度退化越严重,而加筋长细比越大,极限强度退化反而越小。针对文中研究的加筋板,当加筋长细比为 0.2时,腐蚀体积率为14%的随机点蚀导致结构极限强度退化程度达到约14.0%。因此,加筋的随机点蚀损伤会显著削弱加筋板结构的极限强度,其影响不可忽略。 相似文献
2.
针对构件外表面局部区域遭受随机点蚀损伤的圆管截面,考虑点蚀随机特性的影响,建立包含点蚀坑细节的精细有限元模型;在多种腐蚀强度下,研究局部腐蚀的点蚀区分布位置(沿轴向和周向分布位置变化)及其形状(点蚀区长度和宽度独立或联合变化)影响轴压极限强度退化的规律;并比较局部随机点蚀与局部均匀腐蚀引起构件极限强度退化的差异。研究结果表明,尽管局部随机点蚀与最大初始几何缺陷的耦合作用会使极限强度的退化趋于严重,但是总体而言点蚀区分布位置变化对圆管极限强度的退化没有显著的影响。此外,同等腐蚀体积和腐蚀面积下,相比于长窄式局部腐蚀,短宽式局部腐蚀会引起更严重的极限强度退化,在严重腐蚀情形下后者导致的强度退化会高出25.5%;相比于局部均匀腐蚀,局部随机点蚀会导致更剧烈的极限强度退化,其不利影响可高出20.7%。 相似文献
3.
Artificial neural networks and their application to assessment of ultimate strength of plates with pitting corrosion 总被引：1，自引：0，他引：1
The potential for the structural capability degrading effects of both corrosion and fatigue induced cracks are of profound importance and must be both fully understood and reflected in vessel's inspection and maintenance programme. Corrosion has been studied and quantified by many researchers, however its effect on structural integrity is still subject to uncertainty, particularly with regards to localized corrosion. The present study is focused on assessing the effects of localized pitting corrosion on the ultimate strength of unstiffened plates. Over 265 non-linear finite-element analyses of panels with various locations and sizes of pitting corrosion have been carried out. The results indicate that the length, breadth and depth of pit corrosion have weakening effects on the ultimate strength of the plates while plate slenderness has only marginal effect on strength reduction. Transverse location of pit corrosion is also an important factor determining the amount of strength reduction. When corrosion spreads transversely on both edges, it has the most deteriorating effect on strength. In addition, artificial neural network (ANN) method is applied to derive a formula to predict ultimate strength reduction of locally corroded plates. It is found out that the proposed formulae can accurately predict the ultimate strength of locally corroded plates under uniaxial in-plane compression. 相似文献
4.
5.
《中国海洋工程》2020,(4)
An investigation is conducted on the static ultimate limit state assessment of ship hull plates with elastically restrained edges subjected to axial compression. Both material and geometric non-linearities were considered in finite element(FE) analysis. The initial geometric imperfection of the plate was considered, while the residual stress introduced by welding was not considered. The ultimate strength of simply supported ship hull plates compared well with the existing empirical formula to validate the correctness of the applied boundary conditions, initial imperfection and mesh size. The extensive FE calculations on the ultimate strength of ship hull plates with elastically restrained edges are presented. Then a new simple empirical formula for plate ultimate strength is developed, which includes the effect of the rotational restraint stiffness, rotational restraint stiffness, and aspect ratios. By applying the new formula and FE method to ship hull plates in real ships, a good coincidence of the results between these two methods is obtained, which indicates that the new formula can accurately predict the ultimate strength of ship hull plates with elastically restrained edges. 相似文献
6.
In this work, we focus on assessing the group effect of localized corrosion on the ultimate strength of the marine structural plates and study the load-deformation behaviors of plates of various slenderness and uniaxial compression. Meanwhile, we investigate different corroded patterns from a single circular pit to 25 circular pits distributed over the plate and carry out hundreds of nonlinear finite element simulations by combining the number, depth, distribution of pits with imperfections and slenderness of plate. The distribution of multiple pits causes scattering of stress concentration on the plate, then the plastic section of plate changes with wider distribution of damage simultaneously. The ultimate strength arises when un-loading zone comprised of the yielding strips and holes extends across the plate. It can be concluded that the corroded condition defined as group effect of pits manipulates the deformation state and the loading capacity of plate at the ultimate strength mode that coincides with the proportion of effective loading area and section in the process of post-buckling. To validate the effect of pits group, we perform the numerical experiments of the post-buckling of steel plates containing pits in a row with different orientation. 相似文献
7.
提出一种随机分布点蚀损伤的模拟方法,模拟点蚀在构件表面的随机生长过程,并建立了随机态点蚀损伤圆管截面的有限元分析模型;设计了三个受不同腐蚀深度点蚀损伤的圆管构件,并开展轴压试验,利用试验结果校验有限元模型的计算精度;在多种腐蚀情形下(点蚀强度和腐蚀深度变化),研究点蚀分布模式变化引起的极限强度退化及其变异性;比较随机分布点蚀模型与传统腐蚀模型(规则分布点蚀和均匀腐蚀)在计算强度和结构失效行为方面的差异。研究结果表明,点蚀的随机分布模式会引起显著的极限强度变异,且蚀坑深度越大,强度变异越大,蚀坑分布造成的强度极差与强度均值相比达到5%;随机分布点蚀相比于传统腐蚀模型,除了引起更为严重的强度削减,还会改变结构的破坏模式。提出的随机点蚀损伤的模拟方法,可替代昂贵的构件试验,应用于评估点蚀损伤圆管截面的极限强度,增强评估结果的可靠性。 相似文献
8.
为了研究循环载荷作用下扶强材初始损伤对其极限强度的影响,进行了14组扶强材的循环加载试验和分析。构造了考虑材料累积损伤完整、断筋和大变形的扶强材单元极限承载力计算公式,提出了相应循环载荷作用下损伤扶强材单元的端缩曲线表达式和船体梁极限强度计算的简化逐步破坏法。编制了循环载荷作用下船体梁损伤极限强度计算程序,进行了船体梁极限强度计算,并与有限元结果进行对比。研究结果表明：改进的损伤扶强材模型可较为准确地描述扶强材材料损伤的完整、断筋和大变形的极限承载力退化情况,扶强材腹板断裂的损伤相较初始大变形及材料累积损伤形式承载力下降程度更明显;所提出的循环载荷作用下损伤船体梁极限强度计算的简化逐步迭代方法,能定量地计算扶强材在不同类型损伤下的极限承载力退化程度,具有较高精度,方便易行,可应用于工程设计。 相似文献
9.
点蚀损伤下桩基式平台腿柱轴压极限承载力研究 总被引：2，自引：0，他引：2
采用圆柱体点蚀损伤模型,建立含细观尺度点蚀损伤的桩基式平台腿柱多尺度精细化数值模型,研究壁厚损伤度、点蚀损伤强度以及点蚀体积损伤强度影响平台腿柱轴压极限承载力的规律。研究结果表明,壁厚损伤度及点蚀损伤强度明显削弱平台腿柱的极限强度,且随点蚀损伤强度增大壁厚损伤度的影响加剧;点蚀体积损伤强度由于综合考虑了壁厚损伤度和点蚀损伤强度的耦合因素,相比于独立考虑后两者,其更能合理地描述点蚀损伤对平台腿柱极限强度的影响,故点蚀体积损伤强度体现了点蚀损伤的关键特征。本方法不仅适用于研究点蚀损伤构件的极限承载力,其所提出的点蚀损伤模型的构建方法,可拓展于研究受点蚀损伤的整体平台结构的极限承载力,且确定点蚀体积损伤强度为描述点蚀损伤特征的关键参数后,有望将其用于修正点蚀损伤平台腿柱的承载力设计公式。 相似文献
10.
Based on the elastic-plastic, large-deformation finite element method, burst capacity of steel pipeline with longitudinal corrosion defect subjected to internal pressure is studied. The appropriate stress-based criterion is used to predict the failure pressure of finite element model of corroded pipeline under internal pressure. By considering the pipe steel grades and geometries of corrosion defects, a series of finite element analyses is conducted. The effects of corrosion depth, length and width on burst capacity are also discussed. A specific failure pressure solution for the assessment of corrosion defects in moderate-to-high strength pipeline is proposed on the base of numerical results. The failure pressures predicted by the proposed method are in better agreement with the experimental results than the results by the other methods. 相似文献
11.
The present paper is Part I of a series of three papers prepared by the authors on the methods useful for ultimate limit state assessment of marine structures, that have been developed in the literature during the last few decades. It is considered that such methods are now mature enough to enter day-by-day design and strength assessment practice. The aims of the three papers are to conduct some benchmark studies of such methods on ultimate limit state assessment of (unstiffened) plates, stiffened panels, and hull girders of ships and ship-shaped offshore structures, using some candidate methods such as ANSYS nonlinear finite element analysis (FEA), DNV PULS, ALPS/ULSAP, ALPS/HULL, and IACS common structural rules (CSR) methods. As an illustrative example, an AFRAMAX-class hypothetical double hull oil tanker structure designed by CSR method is studied. In the present paper (Part I), the ultimate limit state assessment of unstiffened plates under combined biaxial compression and lateral pressure loads is emphasized using ANSYS, DNV PULS, and ALPS/ULSAP methods, and their resulting computations are compared. Part II will deal with methods for the ultimate limit state assessment of stiffened panels under combined biaxial compression and lateral pressure using ANSYS, DNV PULS, and ALPS/ULSAP methods, and Part III will treat methods for the progressive collapse analysis of the hull structure using ANSYS, ALPS/HULL, and IACS CSR methods. 相似文献
12.
With the support of big data and GPU acceleration training, the artificial intelligence technology with deep learning as its core is developing rapidly and has been widely used in many fields. At the same time, feature extraction operations are required by the current image-based corrosion damage detection method in the field of ships, with little effect but consuming the large amount of manpower and financial resources. Therefore, a new method for hull structural plate corrosion damage detection and recognition based on artificial intelligence using convolutional neural network is proposed. The convolutional neural network (CNN) model is trained through a large number of classified corrosion damage images to obtain a classifier model. Then the classifier model is used with overlap-scanning sliding window algorithm to recognize and position the location of corrosion damage. Finally, the damage detection pattern for hull structural plate corrosion damage as well as other types of superficial structural damage using convolutional neural network is proposed, which can accelerate the application of artificial intelligence technology into the field of naval architecture & ocean engineering. 相似文献
13.
主要探讨了半潜钻井平台浮体结构由于受到海洋环境腐蚀作用后的时变极限强度问题。首先,总结各种关于腐蚀损伤的平均厚度缩减模型,选择较能反映实际腐蚀过程的数学模型来估量浮体的钢板厚度缩减。在此基础上进行一系列极限强度计算,根据计算结果给出浮体极限强度预报公式。最后研究不同纵向构件板厚折减对极限强度的影响,发现浮体角隅板的单位体积影响率最高,而占结构比例大的构件厚度折减也将使得强度大大削弱,这两类纵向构件需要予以重点腐蚀保护。 相似文献
14.
The failure of a ship hull girder is governed by buckling and plastic collapse of the deck, bottom and side shell steel stiffened plates. The stiffened steel plating in ships is generally subjected to both in-plane and out-of-plane loading and is more important to understand the characteristics of these panels under buckling. Tests are reported on the collapse load of stiffened plates with and without cutout and with reinforced cutout under uniaxial compression. A generalized computer program for the semi-analytical solutions proposed by various investigators based on strut approach and orthotropic plate approach, and a finite element analysis program based on orthotropic plate approach are developed. The panels are also analysed using the finite element analysis software ANSYS. An approximate method based on strut approach is proposed to calculate the collapse load of stiffened plates with cutouts and initial imperfections. The reduction in strength of the panels due to the presence of square cutout, rectangular cutout and increase in strength due to reinforcement around rectangular cutout are calculated based on the test results. Comparisons are made between the test results and predictions based on semi-analytical solutions and finite element analyses, and the uncertainty parameters calculated are discussed. Based on this study it is concluded that the cutout can be reinforced with a maximum increase in strength up to 19% for plate initiated failures. 相似文献
15.
Sang-Rai Cho Joonmo Choung Chang-Min Oh Kang-Su Lee Jung-Yeob Kim 《Ocean Engineering》2010,37(8-9):770-776
CSRs (Common Structural Rules for bulker and tanker), which came into effect in 2006, invoke the concept of the ultimate strength of hull girders. While numerous studies associated with the ultimate capacities regarding global hull girders and stiffened panels have been carried out, there are few application cases of the ultimate strengths for deck machineries and their supporting structures. In the present study, nonlinear finite element analyses have been performed to obtain ultimate capacities for a size 450 DIN type bollard including hull foundation structures for which elastic strength assessments based on allowable stress analyses were jointly carried out by a Mooring Fitting SWL Standardization Committee consisting of four major Korean shipbuilders (DSME, HHI, HHIC, and SHI) in 2003. The plastic hardening property is identified from a comparison of the results of ultimate strength simulations and a bollard tension tests performed by the committee. It is assumed that the ultimate load is the corresponding load point when the deformation slope of the bollard column reaches the critical slip angle. It is concluded that the reinforcements appear to be effective with respect to the allowable stress criterion, but are not substantially effective from the point of view of ultimate capacities. In other words, structural reinforcements based on allowable stress analyses may noticeably increase production costs, but do not remarkably raise the ultimate capacities. 相似文献
16.
The present paper is Part II of a series of three papers on methods useful for the ultimate limit state assessment of ships and ship-shaped offshore structures. In contrast to Part I [Paik et al., 2007a. Methods for ultimate limit state assessment of ships and ship-shaped offshore structures: Part I unstiffened plates, Ocean Engineering, doi:10.1016/j.oceaneng.2007.08.004] that deals with unstiffened plates, the present paper (Part II) is focused on methods for the ultimate limit state assessment of stiffened plate structures under combined biaxial compression and lateral pressure actions. The object structure is the bottom part of an AFRAMAX-class hypothetical double-hull oil tanker structure designed by IACS common structural rules (CSR) method, that is the same ship studied in Part I. Three candidate methods, namely ANSYS nonlinear finite element method, DNV PULS method, and ALPS/ULSAP method, are employed for the present study. The results and insights developed from the present study are summarized in terms of ultimate strength characteristics of bottom-stiffened plate structures. 相似文献
17.
Jeom Kee Paik 《Ocean Engineering》2009,36(3-4):266-276
The main objective of the present paper is to numerically examine the residual ultimate strength characteristics of steel plates with longitudinal cracks under axial compressive actions. The present paper is a sequel to the author's previous paper [Paik, J.K., 2008. Residual ultimate strength of steel plates with longitudinal cracks under axial compression—Experiments. Ocean Engineering 35, 1775–1783]. In contrast to the previous paper, the present paper deals with nonlinear finite element method investigations. Because the test programme is usually limited to a few test models in number for many reasons, the application of nonlinear finite element methods is often more beneficial to handle a more variety of parameters of influence. In the present paper, the insights developed from a series of ANSYS nonlinear finite element method computations are documented, where the effects of the crack orientation, the crack location, the crack size, the plate thickness, and the plate aspect ratio on the residual ultimate strength of steel plates with longitudinal cracks under axial compression are discussed. The insights developed from the present work will be useful for cracking damage-tolerant design of steel-plated structures and also for health monitoring or condition assessment of aging steel-plated structures with cracking damages. 相似文献
18.
In jacket-type offshore structures, corrosion damage affects the structural performance under compressive loading, which is created by the working and design loads of the main system. In this study, the effects of corrosion damage on the compressive structural behavior and strength of steel tubular members were investigated. Artificial corrosion damage was applied to the tubular specimens via mechanical processing and hand drilling to replicate the inclined nature of jacket-type offshore structures. The damage was applied to either half or all of the circumference of the specimens. The compressive failure modes of the artificially corroded tubular members were affected by the corrosion conditions. The compressive strengths were also affected by the level of corrosion. From the results of this study, the residual compressive strengths of corroded tubular steel members can be estimated based on the condition of the damaged sectional areas. 相似文献
19.
钢筋锈蚀是严重威胁结构安全的耐久性问题,基于压磁效应,研究均匀锈蚀和坑蚀两种锈蚀钢筋的应力状态与压磁场变化的关系。首先,采用通电加速锈蚀方法进行钢筋均匀锈蚀和点蚀试验;然后,通过轴向拉伸静载试验和疲劳加载试验,分析锈蚀钢筋的压磁信号特征。试验结果显示,磁感强度与钢筋应力状态之间具有较好的对应关系,屈服阶段不同锈蚀率下的钢筋磁感强度曲线有较明显区别,疲劳荷载作用下锈蚀钢筋的法向残余磁感强度和磁滞回环面积均呈现疲劳三阶段变化规律,可进一步运用于钢筋应力状态的检测中。 相似文献
20.
Corrosion of offshore platforms is inevitable. In an ocean corrosion environment, the strength of a platform is weakened greatly. When simultaneously subjected to earthquakes or other extreme loads, the ultimate bearing capacity of the corroded platform is dramatically reduced, resulting in compounded damage from both corrosion and earthquake. Thus, the influence of corrosion cannot be neglected in the seismic performance investigation of platforms. The commonly used corrosion model in platform design is uniform corrosion, and the corrosion rate rule for any parts or zones in a platform is the same. In real cases, however, there are significant differences between the corrosion characteristics in different parts of a platform. Based on theoretical aspects and measured data, a zonal time-variant corrosion model of a platform is developed for a seismic collapse performance investigation. The pushover and incremental dynamic analysis (IDA) methods are adopted here to calculate the collapse margin ratio (CMR), there serve strength ratio (RSR) and ductility coefficient (μ) that are frequently used for the safety reserve evaluation of a platform. The failure reason and collapse probability of platforms considering different service periods are compared. The most prominent feature of the proposed time-variant zonal corrosion model is to capture potential switch of weak location and resulting failure path of corroded jacket offshore platforms although the proposed model needs further calibration by more reliable in-field measured data. As expected, corrosion can definitely cause a reduction in earthquake resistance of a jacket offshore platform, as well as ultimate deformability. The coupled effect between the time-variant vibration properties of the platform and the spectral characteristics of selected motions, the collapse-level spectral acceleration (SA) does not always decrease with increasing corrosion degree. The curves corresponding to normalized CMR and RSR agree very well with each other in the early corrosion development stage and service period beyond 30 years. Some distinct differences can be found during the two stages, with the greatest difference up to 10% for the example platform. 相似文献