共查询到20条相似文献，搜索用时 31 毫秒
1.
液氮温度极低（?195.8℃）,当与储层岩石接触时,能够改变岩石物性并对岩石结构产生损伤致裂,因此,可用于储层压裂改造。为了研究液氮压裂时低温对岩石力学性能的影响,分别对不同含水状态（干燥与饱和）的不同类型（大理岩、砂岩和花岗岩）岩石进行液氮冻结处理,并对冻结前、后岩样进行抗拉及单轴抗压强度对比测试。结果表明,经液氮冻结后,岩石的单轴抗压强度、抗拉强度和弹性模量都降低;岩石在干燥状态下,液氮冻结对大理石强度的影响大于对红砂岩的影响;岩石饱和水状态下,液氮冻结对红砂岩强度的影响大于对大理岩的影响;饱和水状态岩石经液氮冻结后,其应力-轴应变曲线在弹性变形阶段出现一个拐点;对于同种类型岩石,饱和水状态能加剧液氮冻结并对岩石损伤,岩石强度影响显著;对3种岩样微观结构进行了电镜扫描（以大理岩为例进行分析）,发现经液氮冻结后在矿物颗粒之间生成了微裂隙。研究结果可为进一步研究液氮压裂机制提供试验依据。 相似文献
2.
Y?lmaz Mahmuto?lu 《Engineering Geology》2006,82(3):137-144
It is well known rock masses contain several types of weakness planes varying from micro-fissure to fault in size. The fracture frequency, degree of saturation and time are the basic rock parameters affecting its behaviour. However, in most cases, it is practically difficult to test heavily fractured rock in laboratory environment. In this study, the effects of micro cracks, strain rate and water saturation on strength are discussed using a small-scale physical experiments. It is attempted to detach the grain boundaries of coarse-grained rock specimens of the Mu?la marble by thermal treatment that would serve as a small-scale physical simulation of fractures in rock masses and enable a discussion of the variations in time dependent mechanical behaviour. An experimental study was conducted on marble specimens induced thermally by micro-cracks in different frequencies. The thermal treatment periods being 24 h in inert atmospheric condition were varied for each test specimen except categories A and G. Effective porosity increased up to 2.4% after the last thermal cycle of category F. Then conventional compression tests with different strain rates were carried out using a servo-controlled testing machine on both dry and saturated specimens. It is concluded that both lowering strain rates and increasing porosity related with thermally induced micro cracks have important effects on strength and failure path. The progressive failure entirely occurs along the grain boundaries fissured by cyclical treatment and inter-granular deformation depends upon degree of thermal influence. The small-scaled laboratory model enabled to demonstrate that parameters such as joint frequency, time and saturation have a significant effect on mechanical behaviour of rock masses. 相似文献
3.
Hossein Rafiei Renani C. Derek Martin Evert Hoek 《Geotechnical and Geological Engineering》2016,34(1):297-312
The Christensen criterion, originally introduced in materials science, has a simple mathematical form and uniaxial tensile and compressive strength as the only parameters, making it an attractive candidate for rock engineering purposes. In this study, the applicability of the criterion to rock materials is examined. Explicit equations for application of the criterion under biaxial, triaxial compression, triaxial extension, and polyaxial states of stresses are derived. A comprehensive strength data set including the results of tests on synthetic rock, chert dyke, Carrara marble and Westerly granite is utilized to examine the accuracy of the Christensen criterion to the failure of rock material. The two surprising findings about the Christensen criterion are the zero values of tensile strength and the very low slopes of the failure envelope obtained from fitting analyses for chert dyke and Westerly granite. It is shown that the two problems are interrelated and the values of tensile strength tend to zero to produce higher slopes. It is then mathematically proven that the maximum initial slope of the Christensen failure envelope is limited to 4 in triaxial compression and 2.5 in triaxial extension which is considerably lower than the slope of experimental data. The accuracy of the Christensen criterion was found to be significantly lower than the well-established Hoek–Brown criterion. The circular π-plane representations and brittle-to-ductile transition limits from the Christensen criterion are also inconsistent with the observed behavior of rocks. 相似文献
4.
Hangyu Dong Baohua Guo Yizhe Li Kai Si Long Wang 《Geotechnical and Geological Engineering》2017,35(3):1169-1183
The prime objective of this work is to provide a reference to predict the peak shear strength of rock fractures. The paper studied some shear properties of rock fractures and proposed an empirical formula for the peak shear strength of rock fractures based on 3D morphology parameters. The rock fractures were induced in cylindrical sandstone and marble specimens by means of indirect tension. A rock direct shear apparatus (RDS-200) was adopted to conduct direct shear tests on five groups of rock fractures under different levels of normal load. Before the direct shear test, 3D morphology parameters of rock fracture surfaces were obtained using a 3D optical scanner. By analyses of direct shear test data, the relationships between peak shear strength, peak shear displacement, peak dilatancy angle, residual friction coefficient and peak normal stress were found. According to the evolution trends of peak shear strength and peak dilatancy angle along with the normal stress, an empirical formula was proposed to predict the peak shear strength of rock fractures in both sliding and cutting failure modes considering the 3D morphology parameters of rock fracture surfaces. The empirical formula could be commonly used for different types (sandstone and marble) and grain sizes (powder-grained, fine-grained, medium-grained and coarse-grained) of rock fractures. 相似文献
5.
在露天矿边坡稳定性计算和评价过程中,边坡稳定性评价结果与岩体力学参数的选取密切相关。而在冻融循环条件下,岩石的物理力学参数随着冻融次数的变化而变化。首先通过室内模拟的方法对粗砂岩和细砂岩进行不同次数的冻融循环试验,然后进行一系列的单轴和三轴压缩试验,得到冻融循环条件下完整粗砂岩和细砂岩的物理力学参数;基于Hoek-Brown强度准则中的爆破扰动参数D,提出冻融循环劣化参数Df,利用修正的Hoek-Brown准则得到冻融循环条件下岩体力学参数,并分析了边坡岩体的破坏模式。结果表明:随着冻融循环次数的增加,粗砂岩和细砂岩的单轴抗压强度、弹性模量和黏聚力降低减小,内摩擦角变化较小;而岩体的单轴抗压强度、整体抗压强度、抗拉强度、变形模量、黏聚力和内摩擦角均减小,这说明岩体在冻融循环环境中是不断损伤的,质量逐渐变差;随着冻融循环次数不断增加,岩体的抗剪强度劣化在不断加速,边坡的破坏形式主要为剪切破坏。修正的岩体力学参数为露天矿边坡稳定性分析提供更为准确的数据。 相似文献
6.
岩石内部存在的裂隙、孔洞等天然损伤对岩石的力学性能和破坏过程有重要影响,依据细胞自动机理论结合CT无损识别技术实现了含天然裂隙岩石在劈裂条件下裂纹扩展和贯通全过程及其力学性能变化规律的研究。从裂隙砂岩的真实细观结构出发,构建了天然裂隙岩石的数值计算模型,运用CASRock数值计算软件完成了含不同裂隙倾角的砂岩劈裂破坏的数值试验,分析了裂隙倾角对砂岩的力学特性、裂纹扩展过程及能量演化的影响规律。研究表明:(1)天然裂隙砂岩的抗拉强度与裂隙倾角密切相关,随着裂隙倾角的增加,其抗拉强度呈现先减小后增加的趋势;(2)裂隙起裂于天然裂隙尖端,当裂隙倾角0°≤θ<48°时,岩样的破坏是由错开型裂纹引起,裂纹沿着与天然裂隙近垂直方向扩展;当裂隙倾角48°≤θ<94°时,岩样的破坏是由张开型裂纹引起,裂纹沿着与天然裂隙近平行方向扩展;(3)劈裂过程中裂纹尖端应力场存在拉应力区和压应力区,拉应力造成翼裂纹由天然裂隙尖端沿加载端方向萌生扩展,而压应力则引发次生裂纹沿天然裂隙方向扩展;(4)含天然裂隙砂岩劈裂破坏过程能量演化可划分为4个阶段,随裂隙倾角的增大,峰值点处的总能量密度、弹性能密度先缓慢减少再迅速增加,但对岩样耗散能影响不大。 相似文献
7.
岩石受热后的强度,变形破坏特性的微观研究 总被引：1，自引：0，他引：1
本文对砂岩、灰岩、大理岩在不同温度条件下的单轴抗压强度进行了实验研究,并对岩石在各种温度下结构变化进行了镜下分析,探讨了岩石受热后的破裂机理,定性定量地分析了岩石裂纹随温度变化而发展的规律。研究和分析结果表明:在热应力和外应力的作用下,随着温度增加,砂岩单轴抗压强度有增加的趋势,而灰岩、大理石的强度则有所降低。温度对这几种岩石的变形和破坏特性也有很大影响。 相似文献
8.
岩石各向异性实验研究及对工程勘探的影响 总被引：1，自引：0，他引：1
以不同的砂岩和大理岩为标本,对岩石的各向异性在应力应变关系、波速、动静杨氏模量、动静泊松比、抗压强度等方面的各向异性问题进行了测试和研究。通过实验得到岩石标本在平行层理和垂直层理方向上述物理性质存在着的差异情况和变化规律,分析和探讨了岩层的各向异性对工程勘探工作带来的影响情况。指出地壳介质的岩体各向异性对地球物理勘探来说是不能忽视的,尤其是各向异性会导致横波分裂,影响横波勘探的精度,但同时也有助于了解岩体中裂纹结构的信息,做出工程事故的准确预报。 相似文献
9.
水与温度变化是工程岩石物理力学性能劣化的典型风化因素。对不同含水状态及经受不同次数冻融循环损伤后的红砂岩岩样进行了单轴压缩、劈裂拉伸及变角剪切试验。结果表明,红砂岩抗压强度、弹性模量、劈拉强度、黏聚力及内摩擦角等主要力学指标随含水率和冻融循环次数的增大均有不同程度的降低,但降低规律有所不同。水对岩石有明显的软化作用,冻融循环累积损伤显著。利用微观电镜扫描分析了不同含水率及冻融损伤后岩样微观结构的变化规律,认为吸水及冻融循环过程中水对红砂岩的软化表现为溶蚀作用与介质作用,温度变化的作用表现在热变形不协调和相变作用。提出了冻融循环作用下红砂岩力学特性衰减模型,并据此分析了各力学指标的衰减速率和半衰期。该研究结果对涉水岩石工程及寒区岩石工程具有一定的意义。 相似文献
10.
岩溶化裂隙岩体是普遍发育于自然界中具有初始损伤的岩体。为了研究岩溶化裂隙岩体损伤破坏特征,本文以贵州某地赋存的溶蚀岩体为研究对象,运用损伤力学理论构建岩溶化裂隙岩体在单轴压缩条件下的损伤演化模型,并建立岩溶化裂隙岩体损伤演化方程。采用颗粒流数值软件进行单轴压缩数值试验,进一步研究岩溶化裂隙岩体试件在单轴压缩条件下的损伤演化特征,分析岩溶化裂隙岩体的微观损伤特征。结果表明:岩溶化裂隙岩体的初始损伤主要包括溶蚀损伤和裂隙损伤。岩溶化裂隙岩体的初始损伤随着溶蚀率的增加而增加,最终增加速率趋于平缓;岩溶化裂隙岩体的损伤演化曲线均呈“S”型变化,先缓慢增加,再迅速增加,最后缓慢增加至损伤值1;岩溶化裂隙岩体存在异构特征,导致破坏裂隙起源于具有初始损伤的溶蚀孔洞和裂隙处,随后裂隙经历萌发、扩张和剪切作用、数量和长度增加以及裂隙贯通4个阶段后发生宏观破坏。 相似文献
11.
Fracturing and Failure Behavior of Carrara Marble in Quasistatic and Dynamic Brazilian Disc Tests 总被引：1，自引：0，他引：1
Louis Ngai Yuen Wong Chunjiang Zou Yi Cheng 《Rock Mechanics and Rock Engineering》2014,47(4):1117-1133
The tensile strength and fracturing behavior of Carrara marble subjected to the dynamic Brazilian disc test using the split Hopkinson pressure bar technique are determined and compared with those obtained by the conventional quasistatic Brazilian disc test. Detailed observation of the cracking processes is aided by high-speed video footage captured at a frame rate of 100,000 frames per second. The dynamic increase factor is computed, revealing a strong strain rate dependence of the Carrara marble when subjected to strain rates above 1 s?1. Similar to the quasistatic loading tests, conspicuous white zones/patches commonly appear prior to the initiation of visible cracks in the dynamic loading tests. Identification of the white patch initiation and evolution is aided by image comparison software. Comparing the cracking and failure processes under quasistatic and dynamic loading, some distinct differences in the white patch geometry and initiation load are observed. In addition, the extent of the compressive failure zones around the contact points between the loading platens and specimens is found to increase with the strain rate. 相似文献
12.
以花岗斑岩和灰岩两种岩性岩石为代表,实验研究了冻融作用下,岩石的致密程度、孔隙率等物理指标对岩石物理力学性质的影响. 通过不同次数的冻融循环实验,对花岗斑岩和灰岩2种典型岩石样本的质量、单轴抗压强度、抗拉强度、冻融系数、风化程度的变化规律进行对比分析,并绘出了冻融次数与试样的抗压强度、抗拉强度、冻融系数的拟合关系曲线. 在一定限定条件下,将实验结果应用于西藏玉龙铜矿花岗斑岩、灰岩边坡的具体实例中,采用强度折减法计算出了矿山边坡冻融风化前、后的安全系数,对比分析了花岗斑岩、灰岩边坡受冻融风化的影响程度,为矿山的设计和施工提供了参考. 相似文献
13.
为了探究川藏交通廊道沿线典型岩石冻融循环条件下的劣化规律,选取昌都-林芝段的花岗岩、片麻岩和砂岩为试验对象,开展冻融循环条件下岩石加卸荷试验,结果表明:（1）随着冻融循环次数的增加,岩石抗压强度损失率达30%,粘聚力降幅达18.4%,内摩擦角降幅达10.5%,弹性模量逐渐下降,泊松比逐渐增加;（2）三轴压缩试验中,岩样的变形模量呈现与抗压强度类似的劣化趋势,但是变形模量的劣化幅度比抗压强度劣化幅度大;冻融循环作用下岩石抗压强度越大劣化程度越低,对砂岩的劣化最明显,片麻岩次之,花岗岩最小;（3）与三轴压缩试验相比,在卸围压试验中,冻融循环作用对岩石的卸荷量同样有劣化作用,卸荷程度较小时岩石劣化并不明显,随着卸荷量的逐渐增加,卸荷量大于80%时,岩石的变形模量呈指数型下降,泊松比呈指数型增加;（4）随着冻融循环次数的增加,三轴压缩试验中由拉张和剪切破坏造成的裂纹数量增多;卸围压试验中岩石以拉张破坏为主;岩石微裂纹数量增加的同时,不平整度增加,矿物颗粒之间的胶结状态变差;（5）综合试验结果分析,冻融作用对岩石劣化作用最强的为砂岩,其次是片麻岩,最弱为花岗岩. 相似文献
14.
用相似材料制作含预制裂隙岩体无锚和加锚试样,以锚杆与裂隙呈45°、90°打入锚杆制作3组试样,进行60次冻融循环,对冻融过程中裂隙进行应变监测并对冻融循环60次后的试样进行单轴压缩试验,探讨冻融循环作用下不同角度的锚杆支护对裂隙岩体的裂隙扩展规律、锚固效应及破坏模式的影响。研究结果表明:裂隙岩体在经历30次冻融循环之前,两种支护方式对裂隙的控制效果相当,随着冻融循环的进行,锚杆支护角度会对作用于锚杆的摩阻力产生一定影响,锚杆与裂隙夹角越大,作用于裂隙的摩阻力越大;天然状况下一个冻融循环周期内裂隙的应变大致经历了冷缩→冻胀→冻胀稳定→融缩→回弹→稳定6个阶段,两种支护工况均未出现明显的融缩阶段和回弹阶段,且90°支护工况效果比45°支护工况效果更加明显;对裂隙岩体采用水泥浆进行压力灌浆,由于水泥浆的保护作用可以对整个锚固系统起到一定的修复作用;锚杆增强了裂隙岩体抵制裂隙扩展的能力,降低了裂隙岩体劈裂破坏的突然性,且破坏模式由张拉破坏转换为张剪复合破坏。 相似文献
15.
Overcoming two inherent limitations presented by the standard bonded-particle model (BPM), the flat-jointed model still lacks extensive application. This study hereby conducts a comprehensive investigation on the application of the flat-jointed model in rock mechanics study. First, after a careful examination on the mechanical behavior of the flat-joint contact, a systematic calibration has been conducted to build numerical models matching the mechanical properties of Carrara marble. Second, the validated model is used to simulate the fracturing behavior of marble specimens containing a single or en-echelon flaws. Finally, the appearance of particle flow code (PFC) models has been compared with the results obtained from optical observation in order to establish a possible correlation between PFC models and real marble regarding microcracking behavior. Discussions suggest that to remove the particle size effect, the model resolution (ratio of sample dimension to the average particle diameter) should be larger than 30 in the flat-jointed model and 150 in the BPM, respectively. Results from the above investigations suggest that the flat-jointed model is capable of matching both the mechanical properties and fracturing behavior of Carrara marble. The numerical model is more reliable to predict the fracturing path at the instant of initiation than at failure. Development of initial fractures is not only controlled by the magnitude of tension force but also influenced by the extent of distribution of tension force. The appearance and components of a fracture in flat-jointed models probably reveal not only its property (tensile or shear) but also the corresponding microcracking behavior of real rocks. 相似文献
16.
为研究锦屏某边坡岩体在开挖卸荷条件下的岩体宏观力学参数,对该区砂岩进行室内卸荷试验研究,结果表明：相对于加载试验,卸荷过程中岩样的强度及变形参数发生了劣化,低、高围压下岩石变形及破裂形式也有所不同。为此,在对SMR及CSMR修正的基础上,提出了考虑开挖方式、边坡形态及卸荷损伤的边坡卸荷岩体的评价体系USMR法。基于USMR法对研究区边坡开挖岩体宏观参数（变形模量Em、岩体抗压强度 、岩体抗拉强度 、岩体抗剪强度参数cm和 ）进行了动态分析,并分别考虑了不同围压 及卸荷损伤De条件下岩体参数的劣化规律。分析表明：开挖卸荷过程中岩体宏观参数发生了不同程度的劣化,拉应力区、低应力区和高应力区岩体参数的劣化规律有所不同,拉应力区及低应力区岩体力学参数对开挖卸荷更加敏感。研究结果对边坡开挖卸荷岩体的稳定性分析与评价具有一定指导意义。 相似文献
17.
风化是云冈石窟目前所面临的严重的地质病害之一,温度和水分的变化是造成石窟岩体风化的重要原因,尤其是在循环冻融条件下岩体更易风化,因此,利用室内试验研究循环冻融条件下云冈石窟砂岩的物理力学性质,对于石窟岩体的稳定性评价和保护具有重要的意义。将取自云冈石窟的砂岩岩样分为饱水组、干燥组和对比组3组,通过对饱水组和干燥组岩样进行35次循环冻融试验,模拟云冈石窟砂岩的风化过程。在冻融循环开始前以及每5次冻融循环结束后,量测岩样的质量、体积,并利用超声检测分析仪对各岩样进行超声纵波测试;利用INSTRON－1346岩石伺服试验机对上述3组砂岩岩样进行单轴压缩试验,并对试验后的岩样进行SEM微观结构分析。通过试验研究,得到不同含水状态下云冈石窟砂岩岩样的冻融破坏特征以及不同循环冻融次数后岩样体积、质量、超声波纵波波速、砂岩的单轴应力-应变全过程曲线、抗压强度、抗冻系数以及微观结构的变化,分析归纳出循环冻融条件下云冈石窟砂岩的主要物理力学特性。 相似文献
18.
由于降雨、季节引起地下水位升降等原因,地壳中岩体常处于干湿循环状态。为研究干湿循环对岩石动态力学性能的影响,以安徽恒源煤矿北风井-259 m处砂岩为研究对象,采用?50 mm变截面分离式霍普金森压杆试验装置,对长径比为0.5的煤矿砂岩试件经干湿循环作用后实施单轴冲击压缩试验,获得了砂岩动态单轴压缩应力-应变曲线。研究发现,由于自由水的Stefan效应,干湿循环1次对砂岩具有增强作用,单轴动态抗压强度最高;其后,随着干湿循环次数的增加,砂岩受水侵蚀物理弱化作用,砂岩动态单轴抗压强度呈乘幂关系降低,砂岩试件的冲击破碎块度逐渐变小。试验结果表明,干湿循环12次时砂岩动态抗压强度比干湿循环1次降低约24%,表现出较强的劣化效应。 相似文献
19.
为研究裂隙岩体结构效应对其等效力学参数的影响,引入基于离散元的合成岩体技术,通过可控的改变三维岩体结构网络中的结构参数,制作相应的合成岩体试件,开展计算机模拟试验研究。结果表明：随岩体中裂隙体积密度增大,裂隙的变形参数和强度参数随裂隙密度增加而减少,其中等效弹性模量对结构面密度变化最为敏感;随岩体中裂隙倾角增加,岩体等效弹性模量随之单调增加,且等效弹性模量的离散程度（标准差）随倾角增加而减小,而各强度参数指标则先减少而后增加,形成一个U形变化规律;岩体等效力学参数均随结构面尺寸增加而减小,同时等效力学参数的离散程度（标准差）随结构面直径增加而增加,其中单轴抗压强度指标变化最为敏感;岩体等效力学参数对裂隙尺寸和产状的离散程度不敏感。该研究结论可为其他结构效应研究提供一种新思路。 相似文献
20.
The durability is a measure of the rock’s ability to resist degradation during its working life. Rock durability is greatly related to the mineralogical composition of rocks, rock texture (crystal interlocking, crystal shape and size), and the nature of fluids that are in contact with rock. Marbles have been among the most important building materials since ancient times. The main aim of this study is to evaluate the durability of Al Masjid Al-Haram marble and Ordinary white marble “Carrara” (M1 and M2) and develop some correlations among the physical and mechanical properties such as P-wave velocity, slake durability index, dry uniaxial compressive strength (UCSDry), abrasion resistance, point load index, impact strength index, Brazilian tensile strength, and Shore hardness. After testing and the evaluation of the test results, strong statistical correlations were found between P-wave velocity and other rock properties. Statistical correlations between the UCSDry other tests were also carried out. The coefficients of regressions (R2) range from 0.6177 to 0.997. The study shows that the UCSDry values of M1 and M2 have positive relationship with P wave velocities. Concluding remark is that the rocks tested in the study have good durability characteristics and can be reliably used for construction projects. On the other hand, the derived empirical equations can be used for the estimation purposes for similar rock types. 相似文献