共查询到20条相似文献，搜索用时 281 毫秒
1.
基于虚拟偏移距方法的各向异性转换波保幅叠前时间偏移 总被引：2，自引：1，他引：1
In this paper, we use the method of pseudo-offset migration （POM） to complete converted wave pre-stack time migration with amplitude-preservation in an anisotropic medium. The method maps the original traces into common conversion scatter point （CCSP） gathers directly by POM, which simplifies the conventional processing procedure for converted waves. The POM gather fold and SNR are high, which is favorable for velocity analysis and especially suitable for seismic data with low SNR. We used equivalent anisotropic theory to compute anisotropic parameters. Based on the scattering wave traveltime equation in a VTI medium, the POM pseudo-offset migration in anisotropic media was deduced. By amplitude-preserving POM gather mapping, velocity analysis, stack processing, and so on, the anisotropic migration results were acquired. The forward modeling computation and actual data processing demonstrate the validity of converted wave pre-stack time migration with amplitude-preservation using the anisotropic POM method. 相似文献
2.
Several parameters are needed to describe the converted-wave （C-wave） moveout in processing multi-component seismic data, because of asymmetric raypaths and anisotropy. As the number of parameters increases, the converted wave data processing and analysis becomes more complex. This paper develops a new moveout equation with two parameters for C-waves in vertical transverse isotropy （VTI） media. The two parameters are the C-wave stacking velocity （Vc2） and the squared velocity ratio （7v,i） between the horizontal P-wave velocity and C-wave stacking velocity. The new equation has fewer parameters, but retains the same applicability as previous ones. The applicability of the new equation and the accuracy of the parameter estimation are checked using model and real data. The form of the new equation is the same as that for layered isotropic media. The new equation can simplify the procedure for C-wave processing and parameter estimation in VTI media, and can be applied to real C-wave processing and interpretation. Accurate Vc2 and Yvti can be deduced from C-wave data alone using the double-scanning method, and the velocity ratio model is suitable for event matching between P- and C-wave data. 相似文献
3.
Focal depth is one of the most difficult seismic parameters to determine accurately in seismology. The focal depths estimated by various methods are uncertain to a considerable degree,which affects the understanding of the source process. The influence of various factors on focal depth is non-linear. The influence of epicentral distance,arrival time residual and velocity model (crust model) on focal depth is analyzed based on travel time formula of near earthquakes in this paper. When wave propagation velocity is constant, the error of focal depth increases with the increase of epicentral distance or the distance to station and the travel time residual. When the travel time residual is constant,the error of focal depth increases with the increase of the epicentral distance and the velocity of seismic wave. The study also shows that the location error perhaps becomes bigger for shallower earthquakes when the velocity is known and the travel time residual is constant. The horizontal error caused by location accuracy increases with the increase of the epicentral distance,the travel time residual and the velocity of seismic waves,thus the error of focal depth will increase with these factors. On the other hand,the errors of focal depth will lead to change of the origin time,therefore resultant outcomes will all change. 相似文献
4.
Active Source Seismic Identification and Automatic Picking of the P-wave First Arrival Using a Convolutional Neural Network 总被引：1，自引：1，他引：0
XU Zhen WANG Tao XU Shanhui WANG Baoshan FENG Xuping SHI Jing YANG Minghan 《中国地震研究》2019,33(2):288-304
In seismic data processing, picking of the P-wave first arrivals takes up plenty of time and labor, and its accuracy plays a key role in imaging seismic structures. Based on the convolution neural network (CNN), we propose a new method to pick up the P-wave first arrivals automatically. Emitted from MINI28 vibroseis in the Jingdezhen seismic experiment, the vertical component of seismic waveforms recorded by EPS 32-bit portable seismometers are used for manually picking up the first arrivals (a total of 7242). Based on these arrivals, we establish the training and testing sets, including 25,290 event samples and 710,616 noise samples (length of each sample:2s). After 3,000 steps of training, we obtain a convergent CNN model, which can automatically classify seismic events and noise samples with high accuracy (> 99%). With the trained CNN model, we scan continuous seismic records and take the maximum output (probability of a seismic event) as the P-wave first arrival time. Compared with STA/LTA (short time average/long time average), our method shows higher precision and stronger anti-noise ability, especially with the low SNR seismic data. This CNN method is of great significance for promoting the intellectualization of seismic data processing, improving the resolution of seismic imaging, and promoting the joint inversion of active and passive sources. 相似文献
5.
Cauchy priori distribution-based Bayesian AVO reflectivity inversion may lead to sparse estimates that are sensitive to large reflectivities. For the inversion, the computation of the covariance matrix and regularized terms requires prior estimation of model parameters, which makes the iterative inversion weakly nonlinear. At the same time, the relations among the model parameters are assumed linear. Furthermore, the reflectivities, the results of the inversion, or the elastic parameters with cumulative error recovered by integrating reflectivities are not well suited for detecting hydrocarbons and fuids. In contrast, in Bayesian linear AVO inversion, the elastic parameters can be directly extracted from prestack seismic data without linear assumptions for the model parameters. Considering the advantages of the abovementioned methods, the Bayesian AVO reflectivity inversion process is modified and Cauchy distribution is explored as a prior probability distribution and the time-variant covariance is also considered. Finally, we propose a new method for the weakly nonlinear AVO waveform inversion. Furthermore, the linear assumptions are abandoned and elastic parameters, such as P-wave velocity, S-wave velocity, and density, can be directly recovered from seismic data especially for interfaces with large reflectivities. Numerical analysis demonstrates that all the elastic parameters can be estimated from prestack seismic data even when the signal-to-noise ratio of the seismic data is low. 相似文献
6.
ShuaiJun Wang BaoJin Liu JianShi Zhang BaoFeng Liu YuLing Duan XiangHui Song XiaoGuo Deng CeJun Ma YiRan Zang 《中国科学:地球科学(英文版)》2015,58(12):2175-2187
Southwest Yunnan, located in the southern segment of the north-south seismic belt, is one of the regions with strong tectonic movement and seismic activity in China. Study on the characteristics of tectonic setting and deep geophysical field in the region is an important issue in basic science. In 2013, we conducted a 600-km-long Menghai-Gengma-Lushui profile of deep seismic wide-angle reflection/refraction and high-resolution seismic refraction in Southwest Yunnan. In this paper, we use 6 groups of clear intracrustal P-wave phases picked from the seismic record sections of 11 shots to build a velocity structure model of basement and 2D crustal P-wave of the region by using finite difference inversion and ray travel time forward fitting technology. The results show that, from south to north, the crust gradually thickens along the profile and its basement shows a significant lateral heterogeneity. In the vicinity of the Nanting River fault, the basement structure shows the character of alternate depressions and uplifts, and the shallowest basement is about 1.0 km. In the vicinity of Tengchong and Lancang, the basement is about 5.0 km deep. The velocity of the middle and lower crust in the region generally increases with the increasing of depth. At the block boundary and beneath the fault tectonic belt, the velocity contours show apparent irregularity and the P-wave velocity changes sharply. In this region, the Moho gradually deepens from south to north with relatively large lateral undulations. The shallowest point of the Moho is located near Menghai at a depth of about 32.0 km. The deepest point of the Moho is located near Tengchong at a depth of about 40.5 km. Between Gengma and Yongde, the Moho shows significantly fast uplifting and depressing with an amplitude of about 4.0 km. Beneath the Nanting River fault, Longling-Ruili fault, Dayingjiang fault and Tengchong volcano, the basement velocity structure, 2D crustal P-wave velocity structure, distribution of average profile velocity and intracrustal interface spreading also show significant changes from the basement to the top of the Moho, indicating that the crustal velocity and medium physical properties beneath the fault tectonic belt are apparently different from the crustal materials on its both sides, which suggests that these faults should be in a certain scale and may extend to the lower crust or the top of the upper mantle. The earthquakes in the region mainly occurred at a depth of 10–20 km, and the seismic activity is related to the intracrustal medium velocity difference and fault belt distribution. The results can serve as the important data of the crust-mantle structure for the analysis of the deep tectonic setting, earthquake precise positioning, seismogenic structure modeling of the seismic activities in Southwest Yunnan, as well as the important reference for the evaluation of seismic hazard and the planning of earthquake disaster mitigation of this region. 相似文献
7.
Zhao Yonggui Jiang Hui Zhao Xiaopeng 《应用地球物理》2006,3(2):69-74
Typical existing methods of tunnel geological prediction include negative apparent velocity, horizontal seismic profile, and the Tunnel Seismic Prediction （TSP） method as this technology is under development at home and abroad. Considering simpler observational methods and data processing, it is hard to accurately determine the seismic velocity of the wall rock in the front of the tunnel face. Therefore, applying these defective methods may result in inaccurate geological inferences which will not provide sufficient evidence for classifying the wall rock characteristics. This paper proposes the Tunnel Seismic Tomography （TST） method using a spatial observation arrangement and migration and travel time inversion image processing to solve the problem of analyzing the velocity structure of wall rock in the front of the tunnel face and realize accurate imaging of the geological framework of the tunnel wall rock. This method is very appropriate for geological prediction under complex geological conditions. 相似文献
8.
XiangyangLi JianxinYuan 《应用地球物理》2005,2(1):i001-i002
We have developed new basic theories for calculating the conversion point and the travel time of the P-SV converted wave (C-wave) in anisotropic, inhomogeneous media. This enables the use of conventional procedures such as semblance analysis, Dix-type model building and Kirchhoff summation, to implement anisotropic processing, and makes anisotropic processing affordable. Here we present these new developments in two parts: basic theory and application to velocity analysis and parameter estimation. This part deals with the basic theory, including both conversion-point calculation and moveout analysis.Existing equations for calculating the PS-wave (C-wave) conversion point in layered media with vertical transverse isotropy (VTI) are strictly limited to offsets about half the reflector depth (an offset-depth ratio, x/z, of 0.5), and those for calculating the C-wave traveltimes are limited to offsets equal to the reflector depth (x/z=1.0). In contrast, the new equations for calculating the conversion-point extend into offsets about three-times the reflector depth (x/z=3.0), those for calculating the C-wave traveltimes extend into offsets twice the reflector depth (x/z=2.0). With the improved accuracy, the equations can help in C-wave data processing and parameter estimation in anisotropic, inhomogeneous media. 相似文献
9.
Seismic data with high signal-to-noise ratios （SNRs） are useful in reservoirexploration. To obtain high SNR seismic data, significant effort is required to achieve noiseattenuation in seismic data processing, which is costly in materials, and human and financialresources. We introduce a method for improving the SNR of seismic data. The SNR iscalculated by using the frequency domain method. Furthermore, we optimize and discussthe critical parameters and calculation procedure. We applied the proposed method on realdata and found that the SNR is high in the seismic marker and low in the fracture zone.Consequently, this can be used to extract detailed information about fracture zones that areinferred bv structural analysis but not observed in conventional seismic data. 相似文献
10.
We analyze the characteristics of different floating datums for static corrections and discuss the methods for determining them. The effect of different floating datum corrections was studied using theoretical model experiments, resulting in the conclusion that the velocity obtained after the floating datum correction with the minimum static correction errors depends on the velocity of the layer below the low velocity layer （LVL） lower boundary and is not related to topographic relief and LVL structure. For the real data processing case, wave equation numerical model experiments were conducted which resulted in a new method for calculating objective functions based on the waveform and modifications to the calculation equation for minimum static correction errors to make the method suitable for real data static correction processing using inhomogeneous velocity models with lower velocity boundary relief. Real data processing results demonstrate the method＇s superiority. 相似文献
11.
JiangWenbo HeZhanxiang LiuHong 《应用地球物理》2003,6(1):22-26
Addressed in this article is a new approach to investigating the near-surface structures through the use of the electromagnetic sounding. The advantages of the electro-magnetic sounding method and the problems of the nearssurface investigation and their solutions are described. Actual examples from the southwestern Takelamagan, western Qaidam and northern Xinjiang are taken to demonstrate the results and the capability of this approach in solving the nearsurface problems. It is also pointed out that the new approach could become both the basis for designing seismic acquisition parameters and determining the seismic shot locations,as well as supplying near-surface velocity models for seismic data processing so as to improve the quality of seismic sections. 相似文献
12.
Underground fractures play an important role in the storage and movement of hydrocarbon fluid. Fracture rock physics has been the useful bridge between fracture parameters and seismic response. In this paper, we aim to use seismic data to predict subsurface fractures based on rock physics. We begin with the construction of fracture rock physics model. Using the model, we may estimate P-wave velocity, S-wave velocity and fracture rock physics parameters. Then we derive a new approximate formula for the analysis of the relationship between fracture rock physics parameters and seismic response, and we also propose the method which uses seismic data to invert the elastic and rock physics parameters of fractured rock. We end with the method verification, which includes using well-logging data to confirm the reliability of fracture rock physics effective model and utilizing real seismic data to validate the applicability of the inversion method. Tests show that the fracture rock physics effective model may be used to estimate velocities and fracture rock physics parameters reliably, and the inversion method is resultful even when the seismic data is added with random noise. Real data test also indicates the inversion method can be applied into the estimation of the elastic and fracture weaknesses parameters in the target area. 相似文献
13.
14.
In this paper, according to the Fujian Seismic Network earthquake catalog records, the Tnow method and the Four Stations Continuous Location method （hereinafter called FSCL） put forward by Jin Xing are inspected by using P-wave arrival information of the first four stations of each seismic event. Results show that for earthquakes within the network, both methods can obtain similar location results and location deviations are small for the majority of the events. For earthquakes outside the network, the location deviation may be amplified as the epicentral distance increases, owing to the seismic station distribution which spread toward the side of the epicenter and the small opening angle between seismic stations used for locating and epicenter. For the FSCL method, the impacts of the wave velocity on the location results may be significant for earthquakes outside the network. Thus, selecting a velocity model which is similar to the actual structure of the wave velocity will contribute to improving location results of earthquakes. The FSCL method can locate more seismic events than the Tnow method. It concludes that the Tnow method makes use of mistake information from some non-triggering stations in earthquake catalog, and some P-wave arrivals are not included in the earthquake catalog due to discontinuous records or unclear records of the seismic phase, which induces incorrect location. 相似文献
15.
Understanding the effects of in situ fluid content and fracture parameters on seismic characteristics is important for the subsurface exploration and production of fractured porous rocks. The ratio of normal-to-shear fracture compliance is typically utilized as a fluid indicator to evaluate anisotropy and identify fluids filling the fractures, but it represents an underdetermined problem because this fluid indicator varies as a function of both fracture geometry and fluid content. On the bases of anisotropic Gassmann's equation and linear-slip model, we suggest an anisotropic poroelasticity model for fractured porous reservoirs. By combining a perturbed stiffness matrix and asymptotic ray theory, we then construct a direct relationship between the PP-wave reflection coefficients and characteristic parameters of fluids(P-and S-wave moduli) and fractures(fracture quasi-weaknesses), thereby decoupling the effects of fluid and fracture properties on seismic reflection characterization.By incorporating fracture quasi-weakness parameters, we propose a novel parameterization method for elastic impedance variation with offset and azimuth(EIVOA). By incorporating wide-azimuth observable seismic reflection data with regularization constraints, we utilize Bayesian seismic inversion to estimate the fluid content and fracture parameters of fractured porous rocks. Tests on synthetic and real data demonstrate that fluid and fracture properties can be reasonably estimated directly from azimuthal seismic data and the proposed approach provides a reliable method for fluid identification and fracture characterization in a gas-saturated fractured porous reservoir. 相似文献
16.
《中国科学D辑(英文版)》2008,(Z2)
Three-component seismic exploration through P-wave source and three-component geophone is an effective technique used in complicated reservoir exploration. In three-component seismic exploration data processing,one of the difficulties is static correction of converted wave. This paper analyzes propagation characteristics of non-converted and converted refracted waves,and discovers a favor-able condition for the formation of converted refracted wave,i.e. the velocity of overlaying medium S wave is much lower than that of underlying medium S wave. In addition,the paper proposes the static correction method of converted wave based on PPS converted refracted wave,and processes the real three-component seismic data with better results of static correction of converted wave. 相似文献
17.
The common-reflection-surface (CRS) stacking is a new seismic imaging method, which only depends on seismic three parameters and near-surface velocity instead of macro-velocity model. According to optimized three parameters obtained by CRS stacking, we derived an analytical relationship between three parameters and migration velocity field, and put forward CRS gather migration velocity modeling method, which realize velocity estimation by optimizing three parameters in CRS gather. The test of a sag model proved that this method is more effective and adaptable for velocity modeling of a complex geological body, and the accuracy of velocity analysis depends on the precision of optimized three parameters. 相似文献
18.
In order to image the 3-D velocity structure of its shallow crust in Kunming region,China,finite-difference seis-mic tomography is used to invert the seismic data selected carefully from six-shot data. The result lays a founda-tion for the discussion of the relationship between the obtained velocity structure and the hidden faults,and for the illumination of the depth extents of main active faults surrounding Kunming city. Puduhe-Xishan fault lies on the western margin of the Kunming basin and is just situated on the west edge of the low velocity anomaly zone found at all depth levels. This indicates that this fault is a borderline fault of the Kunming basin. It can be concluded that the fault dips eastwards with a steep angle and its depth extent is large. Puji-Hanjiacun fault and Heilong-tan-Guandu fault play a role in controlling the low velocity anomaly zone in middle basin. The depth extents of the two faults are comparatively small,without traversing the interface of basin floor. 相似文献
19.
Natural gas origins of large and medium-scale gas fields in China sedimentary basins 总被引：2，自引：0，他引：2
The integrated study of the geological and seismic reflection data from the drilling area of CCSD has discovered that the density and the P-wave velocity of orthogneiss are almost the same as that of the paragneiss in the area; but the orthogneiss and the paragneiss hold different reflection attributes. The strong seismic reflector packes coinciding spatially with the paragneiss suites have implied that the paragneiss buried in the metamorphic crust itself can cause bone-like seismic reflector sets. The P-wave velocity of paragneiss shows little apparent difference with that of the orthogneiss; but its transverse wave velocity is lower, with the Vp/Vs ratios being high. The paragneiss has partially inherited the layering structures and textures of the protolithe of sedimentary rocks, hence shows strong heterogeneity and anisotropy, that is why the paragneiss are able to produce the bone-like reflectors in the upper crust. The low transverse wave velocity of paragneiss often means weak shear resistance, which will further cause cracks or fractures in the rock, consequentially increase its porosity and permeability during tectonic movements, and form the paragneiss reservoirs of low-permeability zones for gases uplifted from the deeper crust. Because the paragneiss in the crustal metamorphic basement can cause the seismic reflectors, seismic reflection sections are able to provide information about the paragneiss under certain prerequisites. 相似文献
20.
Crustal velocity structure of the Shaowu-Nanping-Pingtan transect through Fujian from deep seismic sounding-tectonic implications 总被引：3，自引：0，他引：3
The Shaowu-Nanping-Pingtan deep seismic sounding profile is located in northern Fujian Province. High-quality seismic sounding data were acquired by five large explosive blasts received by 133 digital seismic instruments along the profile. Based on seismic facies analysis and travel-time picking on shot record sections, a model of the velocity structure of upper crust was developed by finite-difference tomography of the first breaks; the 2-D P-wave velocity structure and tectonic characteristics of the crust were interpreted further by fitting of waveforms and seismic travel times. The results show that the top of the crystalline basement is buried at depths of 2.0–4.0 km, with the deepest buried up to 4.0 km within the Fuzhou Basin. The Moho interface was found to be deeper in the west and shallower in the east(i.e., 30.0 km near the coast, increasing to 33.0 km northwestward). The lower crust on the east side of the Zhenghe-Haifeng Fault Zone has a smoothly varying gradient structure, whereas on the west side it has two distinct layers with a boundary between those layers at a depth of 23 km. Seismic velocities on the west side are generally lower than on the east side; a low velocity layer is observed with a lowest speed of 6.25 km/s at a depth of 22 km on the west side, which may consist of partially molten material. The Zhenghe-Haifeng Fault is a deep crustal fault, and should be a channel for deep material upwelling; it has a direct relationship with multiple stages of continental tectonic movements in Southern China and with multiple magmatic events that started in the Proterozoic and ended in the of late Tertiary in Fujian. 相似文献