共查询到20条相似文献，搜索用时 31 毫秒
1.
Shale reservoirs of the Middle and Upper Devonian Horn River Group provide an opportunity to study the influence of rock composition on permeability and pore throat size distribution in high maturity formations. Sedimentological, geochemical and petrophysical analyses reveal relationships between rock composition, pore throat size and matrix permeability.In our sample set, measured matrix permeability ranges between 1.69 and 42.81 nanodarcies and increases with increasing porosity. Total organic carbon (TOC) content positively correlates to permeability and exerts a stronger control on permeability than inorganic composition. A positive correlation between silica content and permeability, and abundant interparticle pores between quartz crystals, suggests that quartz may be another factor enhancing the permeability. Pore throat size distributions are strongly related to TOC content. In organic rich samples, the dominant pore throat size is less than 10 nm, whereas in organic lean samples, pore throat size distribution is dominantly greater than 20 nm. SEM images suggest that in organic rich samples, organic matter pores are the dominant pore type, whereas in quartz rich samples, the dominant type is interparticle pores between quartz grains. In clay rich and carbonate rich samples, the dominant pore type is intraparticle pores, which are fewer and smaller in size.High permeability shales are associated with specific depositional facies. Massive and pyritic mudstones, rich in TOC and quartz, have comparatively high permeability. Laminated mudstone, bioturbated mudstone and carbonate facies, which are relatively enriched in clay or carbonate, have fairly low permeability. 相似文献
2.
A combination of Broad-Ion-Beam (BIB) polishing and Scanning Electron Microscopy (SEM) has been used to study qualitatively and quantitatively the microstructure of Opalinus Clay in 2D. High quality 2D cross-sections (ca. 1 mm2), belonging to the Shaly and Sandy facies of Opalinus Clay, were investigated down to the nanometre scale. In addition Mercury Intrusion Porosimetry (MIP) and X-Ray powder Diffraction experiments have been used to extend characterization of the microstructure to the mm–cm scale on bulk volume sample material. Interestingly, both end-member samples of the Opalinus Clay show qualitatively similar mineralogy and pore characteristics as well as a comparable pore size distribution and pore morphology within the different mineral phases and mineral aggregates. Differences between the facies are mainly due to variations in mineral size and mineral amount present in the alternating layers of the different facies. Six different porous mineral phases have been identified and the pores have been subdivided into ten different pore types. Pores visible in the SEM images are most abundant in the clay matrix and these seem to follow a power law distribution with a power law exponent of ca. 2.25 independent of the sample location. Furthermore, all common mineral grains show characteristic porosity, pore shape and pore size distribution in 2D and are proposed to be considered as elementary building blocks for Opalinus Clay. Combined these homogeneous elementary building blocks make up the heterogeneous fabric of the different facies of Opalinus Clay. Based on extrapolation of the power law size distribution in the clay matrix below SEM resolution results in a porosity of 10–25% for clay rich layers (60–90% of clay matrix), whereas sand and carbonate layers show an extrapolated porosity of 6–14%. These extrapolated porosities are in agreement with water-loss and physical porosity measurements performed on bulk material of comparable samples. 相似文献
3.
X-ray computed tomography and serial block face scanning electron microscopy imaging techniques were used to produce 3D images with a resolution spanning three orders of magnitude from ∼7.7 μm to 7 nm for one typical Bowland Shale sample from Northern England, identified as the largest potential shale gas reservoir in the UK. These images were used to quantitatively assess the size, geometry and connectivity of pores and organic matter. The data revealed four types of porosity: intra-organic pores, organic interface pores, intra- and inter-mineral pores. Pore sizes are bimodal, with peaks at 0.2 μm and 0.04 μm corresponding to pores located at organic–mineral interfaces and within organic matter, respectively. These pore-size distributions were validated by nitrogen adsorption data. The multi-scale imaging of the four pore types shows that there is no connected visible porosity at these scales with equivalent diameter of 20 nm or larger in this sample. However, organic matter and clay minerals are connected and so the meso porosity (<20 nm) within these phases provides possible diffusion transport pathways for gas. This work confirms multi-scale 3D imaging as a powerful quantification method for shale reservoir characterisation allowing the representative volumes of pores, organic and mineral phases to be defined to model shale systems. The absence of connected porosity at scales greater than 20 nm indicates the likely importance of the organic matter network, and associated smaller-scale pores, in controlling hydrocarbon transport. . The application of these techniques to shale gas plays more widely should lead to a greater understanding of properties in the low permeability systems. 相似文献
4.
Shale samples collected from seven wells in the southeastern Ordos Basin were tested to investigate quantitatively the pore structure and fractal characteristics of the Lower Permian Shanxi Shale, which was deposited in a marine-continental transitional (hereinafter referred to as the transitional) environment. Low-pressure nitrogen adsorption data show that the Shanxi Shale exhibits considerably much lower surface area (SA) and pore volume (PV) in the range of 0.6–1.3 m2/g and 0.25–0.9 ml/100 g, respectively. Type III kerogen abundant in the transitional Shanxi Shale were observed to be poorly developed in the organic pores in spite of being highly mature, which resulted in a small contribution of organic matter (OM) to the SA and PV. Instead, I/S (illite-smectite mixed clay) together with illite jointly contributed mostly to the SA and PV as a result of the large amount of inter-layer pores associated with them, which were evident in broad-ion-beam (BIB) imaging and statistical analysis. Additionally, the Shanxi Shale has fractal geometries of both pore surface and pore structure, with the pore surface fractal dimension (D1) ranging from 2.16 to 2.42 and the pore structure fractal dimension (D2) ranging from 2.49 to 2.68, respectively. The D1 values denote a pore surface irregularity increase with an increase in I/S and illite content attributed to their more irregular pore surface compared with other mineralogical compositions and OM. The fractal dimension D2 characterizing the pore structure complexity is closely related to the pore arrangement and connectivity, and I/S and illite decrease the D2 when their contents increase due to the incremental ordering degree and connectivity of I/S- or illite-hosted pores. Meanwhile, other shale constituents (including kaolinite, chlorite, and OM) that possess few pores can significantly increase the pore structure complexity by way of pore-blocking. 相似文献
5.
Studying complex pore structures is the key to understanding the mechanism of shale gas accumulation. FIB-SEM (focused ion beam-scanning electron microscope) is the mainstream and effective instrument for imaging nanopores in gas shales. Based on this technology, 2D and 3D characteristics of shale samples from Lower Silurian Longmaxi formation in southern Sichuan Basin were investigated. 2D experimental results show that the pores in shale are nanometer-sized, and the structure of those nanopores can be classified into three types: organic pores, inorganic pores and micro fractures. Among the three types, organic pores are dominantly developed in the OM (organic matter) with three patterns such as continuous distributed OM, OM between clay minerals and OM between pyrite particles, and the size of organic pores range from 5 nm to 200 nm.Inveresly, inorganic pores and micro fractures are less developed in the Longmaxi shales. 3D digital rocks were reconstructed and segmented by 600 continuous images by FIB cutting and SEM imaging simultaneously. The pore size distribution and porosity can be calculated by this 3D digital core, showing that its average value is 32 nm and porosity is 3.62%.The 3D digital porosity is higher than its helium porosity, which can be regarded as one important parameter for evaluation of shale gas reserves. The 2D and 3D characterized results suggest that the nanometer-sized pores in organic matter take up the fundamental storage space for the Longmaxi shale. These characteristics have contributed to the preservation of shale gas in this complex tectonic area. 相似文献
6.
Nanoporosity of a shale gas reservoir provides essential information on the gas accumulation space and controls the gas reserves. The characteristics of heterogeneous nanoporosity of four shale samples are analyzed by combining quantitative evaluation of minerals by scanning electronic microscopy (QEMSCAN), focused ion beam-scanning electron microscopy (FIB-SEM), and nano-CT. The representative elementary area (REA) is proposed by QEMSCAN to detect the imaging area that can represent the overall contents of minerals and organic matter. Combined with the statistics of pores in minerals and organic matter by FIB-SEM, the quantitative nanoporosity is obtained. The nano-CT is used to compare the total nanoporosity that was obtained by FIB-SEM. The results show that shale has distinct characteristics in nanoporosities due to the variation in organic matter and mineral content. The major pore sizes of the organic matter and clay minerals are smaller than 400 nanometers (nm), and the pore sizes of feldspar and pyrite are mainly 200–600 nm. The pore sizes for pores developed in quartz and carbonate minerals range from a few nanometers to 1000 nm. Furthermore, pores smaller than 400 nm mainly provide the total nanoporosity. The nanoporosities in the organic matter are approximately 17%–21%. Since the organic matter content (0.54%–6.98%) is low, the organic matter contributes approximately 5%–33% of the total nanoporosity in shale. Conversely, the nanoporosities in quartz and clay are generally lower than 3%. Since the mineral content (93.02%–99.46%) is obviously higher than the organic matter content, the minerals contribute approximately 67%–95% of the total nanoporosity in shale. 相似文献
7.
Mineral types (detrital and authigenic) and organic-matter components of the Ordovician-Silurian Wufeng and Longmaxi Shale (siliceous, silty, argillaceous, and calcareous/dolomitic shales) in the Sichuan Basin, China are used as a case study to understand the control of grain assemblages and organic matter on pores systems, diagenetic pathway, and reservoir quality in fine-grained sedimentary rocks. This study has been achieved using a combination of petrographic, geochemical, and mercury intrusion methods. The results reveal that siliceous shale comprises an abundant amount of diagenetic quartz (40–60% by volume), and authigenic microcrystalline quartz aggregates inhibit compaction and preserve internal primary pores as rigid framework for oil filling during oil window. Although silty shale contains a large number of detrital silt-size grains (30–50% by volume), which is beneficial to preserve interparticle pores, the volumetric contribution of interparticle pores (mainly macropores) is small. Argillaceous shale with abundant extrabasinal clay minerals (>50% by volume) undergoes mechanical and chemical compactions during burial, leading to a near-absence of primary interparticle pores, while pores preserved between clay platelets are dominant with more than 10 nm in pore size. Pore-filling calcite and dolomite precipitated during early diagenesis inhibit later compaction in calcareous/dolomitic shale, but the cementation significantly reduces the primary interparticle pores. Pore-throat size distributions of dolomitic shale show a similar trend with silty shale. Besides argillaceous shale, all of the other lithofacies are dominated by OM pores, which contribute more micropores and mesopores and is positively related to TOC and quartz contents. The relationship between pore-throat size and pore volume shows that most pore volumes are provided by pore throats with diameters <50 nm, with a proportion in the order of siliceous (80.3%) > calcareous/dolomitic (78.4%) > silty (74.9%) > argillaceous (61.3%) shales. In addition, development degree and pore size of OM pores in different diagenetic pathway with the same OM type and maturity show an obvious difference. Therefore, we suggest that the development of OM pores should take OM occurrence into account, which is related to physical interaction between OM and inorganic minerals during burial diagenesis. Migrated OM in siliceous shale with its large connected networks is beneficial for forming more and larger pores during gas window. The result of the present work implies that the study of mineral types (detrital and authigenic) and organic matter-pores are better understanding the reservoir quality in fine-grained sedimentary rocks. 相似文献
8.
This contribution presents results from a laboratory study investigating the fluid (gas/water) transport properties in the matrix system of the Scandinavian Alum Shale. The maturity of the organic matter of the shale samples ranged between 0.5 and 2.4% vitrinite reflectance (VRr). Gas (He, Ar, CH4) and water flow properties were determined at effective stresses ranging between 5 and 30 MPa and a temperature of 45 °C. The effects of different controlling factors/parameters on the fluid conductivity including permeating fluid, moisture content, anisotropy, heterogeneity, effective stress, pore pressure, and load cycling were analyzed and discussed. Pore volume measurements by helium expansion were conducted under controlled “in situ” effective stress conditions on a limited number of plugs drilled parallel and perpendicular to bedding.For Alum Shale the intrinsic permeability coefficients measured parallel and perpendicular to bedding (6·10−22–8·10−18 m2) were within the range previously reported for other shales and mudstones. Permeability coefficients were strongly dependent on permeating fluid, moisture content, anisotropy, effective stress and other sample-to-sample variations. The intrinsic/absolute permeabilities measured with helium were consistently, higher (up to five times) than those measured with argon and methane. Permeability coefficients (He, CH4) measured on a dry sample were up to six times higher than those measured on an “as-received” sample, depending on effective stress. The effect of moisture on measured permeability coefficients became more significant as effective stress increased. Permeability coefficients (He, CH4) measured parallel to bedding were up to more than one order of magnitude higher than those measured perpendicular to bedding. Parallel to bedding, all samples showed a nonlinear reduction in permeability with increasing effective stress (5–30 MPa). The stress dependence of permeability could be well described by an exponential relationship. 相似文献
9.
The Lower Silurian Longmaxi Shale in the southeastern Upper Yangtze Region, which has been the main target for shale gas exploration and production in China, is black marine organic-rich shale and rich in graptolites. Graptolites, usually only periderms preserved in shales, are important organic component of the Longmaxi Shale. However, the pore structure of graptolite periderms and its contribution to gas storage has not yet been studied before. A combination of optical microscopy for identification and “mark” of graptolite and scanning electron microscope (SEM) for pore observations were conducted for the Longamxi Shale samples. Results show that pores are anisotropic developed in the Longmaxi graptolite periderms and greatly associated with their fine structure. Micrometer-sized fractures and spindle-shaped pores between cortical fibrils in the cortical bandage are greatly developed at section parallel to the bedding, while they are rare at section perpendicular to the bedding. Besides, numerous sapropel detritus rich in nanometer-sized pores are discretely distributed in the shale. Though graptolite periderms are low porosity from SEM image analysis, microfractures and elongated pores along the graptolite periderm wall may still make the graptolite an interconnected system. Together with the discrete porous sapropel detritus in shale, these graptolite-derived Organic Matter (OM) may form an interconnected organic pore system in the shale. The difference of pore development observed in graptolite periderms and sapropel detritus also give us new insight for the organic pore heterogeneity study. The OM composition, their fine structure and orientation in the rock may be important factors controlling OM pore development. The combination of identifying OM type under optical microscopy and pores observation under SEM for may be an effective method to study the OM pore development especially in shale that contain more OM. 相似文献
10.
Although extensive studies have been conducted on unconventional mudstone (shales) reservoirs in recent years, little work has been performed on unconventional tight organic matter-rich, fine-grained carbonate reservoirs. The Shulu Sag is located in the southwestern corner of the Jizhong Depression in the Bohai Bay Basin and filled with 400–1000 m of Eocene lacustrine organic matter-rich carbonates. The study of the organic matter-rich calcilutite in the Shulu Sag will provide a good opportunity to improve our knowledge of unconventional tight oil in North China. The dominant minerals of calcilutite rocks in the Shulu Sag are carbonates (including calcite and dolomite), with an average of 61.5 wt.%. The carbonate particles are predominantly in the clay to silt size range. Three lithofacies were identified: laminated calcilutite, massive calcilutite, and calcisiltite–calcilutite. The calcilutite rocks (including all the three lithofacies) in the third unit of the Shahejie Formation in the Eocene (Es3) have total organic carbon (TOC) values ranging from 0.12 to 7.97 wt.%, with an average of 1.66 wt.%. Most of the analyzed samples have good, very good or excellent hydrocarbon potential. The organic matter in the Shulu samples is predominantly of Type I to Type II kerogen, with minor amounts of Type III kerogen. The temperature of maximum yield of pyrolysate (Tmax) values range from 424 to 452 °C (with an average of 444 °C) indicating most of samples are thermally mature with respect to oil generation. The calcilutite samples have the free hydrocarbons (S1) values from 0.03 to 2.32 mg HC/g rock, with an average of 0.5 mg HC/g rock, the hydrocarbons cracked from kerogen (S2) yield values in the range of 0.08–57.08 mg HC/g rock, with an average of 9.06 mg HC/g rock, and hydrogen index (HI) values in the range of 55–749 mg HC/g TOC, with an average of 464 mg HC/g TOC. The organic-rich calcilutite of the Shulu Sag has very good source rock generative potential and have obtained thermal maturity levels equivalent to the oil window. The pores in the Shulu calcilutite are of various types and sizes and were divided into three types: (1) pores within organic matter, (2) interparticle pores between detrital or authigenic particles, and (3) intraparticle pores within detrital grains or crystals. Fractures in the Shulu calcilutite are parallel to bedding, high angle, and vertical, having a significant effect on hydrocarbon migration and production. The organic matter and dolomite contents are the main factors that control calcilutite reservoir quality in the Shulu Sag. 相似文献
11.
Currently, the Upper Ordovician Wufeng (O3w) and Lower Silurian Longmaxi (S1l) Formations in southeast Sichuan Basin have been regarded as one of the most important target plays of shale gas in China. In this work, using a combination of low-pressure gas adsorption (N2 and CO2), mercury injection porosimetry (MIP) and high-pressure CH4 adsorption, we investigate the pore characteristics and methane sorption capacity of the over-mature shales, and discuss the main controlling factors for methane sorption capacity and distribution of methane gas in pore spaces.Low pressure CO2 gas adsorption shows that micropore volumes are characterized by three volumetric maxima (at about 0.35, 0.5 and 0.85 nm). The reversed S-shaped N2 adsorption isotherms are type Ⅱ with hysteresis being noticeable in all the samples. The shapes of hysteresis loop are similar to the H3 type, indicating the pores are slit- or plate-like. Mesopore size distributions are unimodal and pores with diameters of 2–16 nm account for the majority of mesopore volume, which is generally consistent with MIP results. The methane sorption capacities of O3w-S1l shales are in a range of 1.63–3.66 m3/t at 30 °C and 10 MPa. Methane sorption capacity increase with the TOC content, surface area and micropore volume, suggesting organic matter might provide abundant adsorption site and enhance the strong methane sorption capacity. Samples with higher quartz content and lower clay content have larger sorption capacity. Our data confirmed that the effects of temperature and pressure on methane sorption capacity of shale formation are opposite to some extent, suggesting that, during the burial or uplift stage, the gas sorption capacity of hydrocarbon reservoirs can be expressed as a function of burial depth. Based on the adsorption energy theory, when the pore diameter is larger than 2 nm, much methane molecular will be adsorbed in pores space with distance to pore wall less than 2 nm; while free gas is mainly stored in the pore space with distance to pore wall larger than 2 nm. Distributions of adsorption space decrease with the increasing pore size, while free gas volume increase gradually, assuming the pore are cylindrical or sphere. Particularly, when the pore size is larger than 30 nm, the content of adsorbed gas space volume is very low and its contribution to the all gas content is negligible. 相似文献
12.
The microstructure of black siliceous shale from the lower Cambrian Niutitang Formation, Sichuan Basin in China was investigated by the combination of field emission scanning electron microscope (FE-SEM) and argon ion beam milling. The nanometer-to micrometer-scale pore systems of shales are an important control on gas storage and fluid migration. In this paper, the organic porosity in shale samples within oil and gas window has been investigated, and the formation mechanism and diagenetic evolution of nanopores have been researched.FE-SEM reveals five pore types that are classified as follows: organic nanopores, pores in clay minerals, nanopores of framework minerals, intragranular pores in microfossils, and microfractures. Numerous organic nanopores are observed in shales in the gas window, whereas microfractures can be seen within the organic matter of shales in the oil window. Microfractures in oil window shales could be attributed to pressure buildup in the organic matter when incompressible liquid hydrocarbon are generated, and the orientation of microfractures is probably parallel to the bedding and strength anisotropy of the formation. Pores in clay minerals are always associated with the framework of clay flakes, and develop around rigid mineral grains because the pressure shadows of mineral grains protect pores from collapse, and the increasing of silt content would lead to an increase in pressure shadows and improve porosity. Nanopores of rock framework are probably related to dissolution by acidic fluids from hydrocarbon generation, and the dissolution-related pores promote permeability of shales. Porosity in the low-TOC, low-thermal-maturity shales contrast greatly with those of high-TOC, high-thermal-maturity shales. While the high-TOC shales contain abundant organic microporosity, the inorganic pores can contribute a lot to the porosity of the low-TOC shales. 相似文献
13.
Low and high resolution petrographic studies have been combined with mineralogical, TOC, RockEval and porosity data to investigate controls on the evolution of porosity in stratigraphically equivalent immature, oil-window and gas-window samples from the Lower Toarcian Posidonia Shale formation. A series of 26 samples from three boreholes (Wickensen, Harderode and Haddessen) in the Hils syncline was investigated. The main primary components of the shales are microfossiferous calcite (30–50%), clay minerals (20–30%) and Type II organic matter (TOC = 7–15%, HI = 630–720 mg/gC in immature samples). Characteristic sub-centimetric light and dark lamination reflects rapid changes in the relative supply of these components. Total porosities decrease from 10 to 14% at Ro = 0.5% to 3–5% at Ro = 0.9% and then increase to 9–12% at Ro = 1.45%. These maturity-related porosity changes can be explained by (a) the primary composition of the shales, (b) carbonate diagenesis, (c) compaction and (d) the maturation, micro-migration, local trapping and gasification of heterogeneous organic phases. Calcite undergoes dissolution and reprecipitation reactions throughout the maturation sequence. Pores quantifiable in SEM (>ca. 50 nm) account for 14–25% of total porosity. At Ro = 0.5%, SEM-visible macropores1 are associated mainly with biogenic calcite. At this maturity, clays and organic matter are not visibly porous but nevertheless hold most of the shale porosity. Porosity loss into the oil window reflects (a) compaction, (b) carbonate cementation and (c) perhaps the swelling of kerogen by retained oil. In addition, porosity is occluded by a range of bituminous phases, especially in microfossil macropores and microfractures. In the gas window, mineral-hosted porosity is still the primary form of macroporosity, most commonly observed at the organic-inorganic interface. Increasing porosity into the gas window also coincides with the formation of isolated, spongy and complex meso- and macropores within organic particles, related to thermal cracking and gas generation. This intraorganic porosity is highly heterogeneous: point-counted macroporosity of individual organic particles ranges from 0 to 40%, with 65% of organic particles containing no macropores. We suggest that this reflects the physicochemical heterogeneity of the organic phases plus the variable mechanical protection afforded by the mineral matrix to allow macroporosity to be retained. The development of organic macroporosity cannot alone account for the porosity increase observed from oil to gas window; major contributions also come from the increased volume of organic micro- and meso-porosity, and perhaps by kerogen shrinkage. 相似文献
14.
The geochemical and petrographic characteristics of saline lacustrine shales from the Qianjiang Formation, Jianghan Basin were investigated by organic geochemical analysis, X-ray diffraction (XRD), scanning electron microscopy (SEM) and low pressure nitrogen adsorption analysis. The results indicate that: the saline lacustrine shales of Eq3 member with high oil content are characterized by type I and type II oil-prone kerogen, variable TOC contents (1.0–10.0 wt%) and an early-maturity stage (Ro ranges between 0.41 and 0.76%). The mineral compositions of Eq3 saline shale show strong heterogeneity: brittle intervals with high contents of quartz and carbonate are frequently alternated with ductile intervals with high glauberite and clay contents. This combination might be beneficial for oil accumulation, but may cause significant challenges for the hydraulic stimulation strategy and long-term production of shale oil. The interparticle pores and intraparticle pores dominate the pore system of Eq3 shale, and organic matter hosted pores are absent. Widely distributed fractures, especially tectonic fractures, might play a key role in hydrocarbon migration and accumulation. The pore network is contributed to by both large size inorganic pores and abundant micro-factures, leading to a relatively high porosity (2.8–30.6%) and permeability (0.045–6.27 md) within the saline shale reservoir, which could enhance the flow ability and storage capacity of oil. The oil content (S1 × 100/TOC, mg HC/g TOC and S1, mg HC/g rock) and brittleness data demonstrate that the Eq33x section has both great potential for being a producible oil resource and hydraulic fracturing. Considering the hydrocarbon generation efficiency and properties of oil, the mature shale of Eq3 in the subsidence center of the Qianjiang Depression would be the most favorable zone for shale oil exploitation. 相似文献
15.
Understanding the pore structure characteristics of tight gas sandstones is the primary purpose of reservoir evaluation and efforts to characterize tight gas transport and storage mechanisms and their controls. Due to the various pore types and multi-scale pore sizes in tight reservoirs, it is essential to combine several techniques to characterize pore structure. Scanning electron microscopy (SEM), nitrogen gas adsorption (N2GA), mercury intrusion porosimetry (MIP) and nuclear magnetic resonance (NMR) were conducted on tight sandstones from the Lower Cretaceous Shahezi Formation in the northern Songliao Basin to investigate pore structure characteristics systematically (e.g., type and size distribution of pores) and to establish how significant porosity and permeability are for different pore types. The studied tight sandstones are composed of intergranular pores, dissolution pores and intercrystalline pores. The integration of N2GA and NMR can be used as an efficient method to uncover full pore size distribution (PSD) of tight sandstones, with pore sizes ranging from 2 nm to dozens of microns. The full PSDs indicate that the pore sizes of tight sandstones are primarily distributed within 1.0 μm. With an increase in porosity and permeability, pores with larger sizes contribute more to porosity. Intercrystalline pores and intergranular/dissolution pores can be clearly distinguished on the basis of mercury intrusion and surface fractal. The relative contribution of intercrystalline pores to porosity ranges from 58.43% to 91.74% with an average of 79.74%. The intercrystalline pores are the primary contributor to pore space, whereas intergranular/dissolution pores make a considerably greater contribution to permeability. A specific quantity of intergranular/dissolution pores is the key to producing high porosity and permeability in tight sandstone reservoirs. The new two permeability estimation models show an applicable estimation of permeability with R2 values of 0.955 and 0.962 for models using Dmax (pore diameter corresponding to displacement pressure) and Df (pore diameter at inflection point), respectively. These results indicate that both Dmax and Df are key factors in determining permeability. 相似文献
16.
The pore size classification (micropore <2 nm, mesopore 2–50 nm and macropore >50 nm) of IUPAC (1972) has been commonly used in chemical products and shale gas reservoirs; however, it may be insufficient for shale oil reservoirs. To establish a suitable pore size classification for shale oil reservoirs, the open pore systems of 142 Chinese shales (from Jianghan basin) were studied using mercury intrusion capillary pressure analyses. A quantitative evaluation method for I-micropores (0–25 nm in diameter), II-micropores (25–100 nm), mesopores (100–1000 nm) and macropores (>1000 nm) within shales was established from mercury intrusion curves. This method was verified using fractal geometry theory and argon-ion milling scanning electron microscopy images. Based on the combination of pore size distribution with permeability and average pore radius, six types (I-VI) shale open pore systems were analyzed. Moreover, six types open pore systems were graded as good, medium and poor reservoirs. The controlling factors of pore systems were also investigated according to shale compositions and scanning electron microscopy images. The results show that good reservoirs are composed of shales with type I, II and III pore systems characterized by dominant mesopores (mean 68.12 vol %), a few macropores (mean 7.20 vol %), large porosity (mean 16.83%), an average permeability of 0.823 mD and an average pore radius (ra) of 88 nm. Type IV pore system shales are medium reservoirs, which have a low oil reservoir potential due to the developed II-micropores (mean 57.67 vol %) and a few of mesopores (mean 20.19 vol %). Poor reservoirs (composed of type V and VI pore systems) are inadequate reservoirs for shale oil due to the high percentage of I-micropores (mean 69.16 vol %), which is unfavorable for the flow of oil in shale. Pore size is controlled by shale compositions (including minerals and organic matter), and arrangement and morphology of mineral particles, resulting in the developments of shale pore systems. High content of siliceous mineral and dolomite with regular morphology are advantage for the development of macro- and mesopores, while high content of clay minerals results in a high content of micropores. 相似文献
17.
The trace and rare earth elements (REE) analyses were conducted on samples collected from a 30 m core of the Marcellus Shale obtained from Greene County, southwestern Pennsylvania. Our results suggest that organic matter enrichment trends in the Marcellus Shale can be directly linked with the Acadian Orogeny. The Acadian Orogeny has been recognized as a main sediment source for the Marcellus Shale. Synthesis of tectonic history and recent ash bed geochronology, reveals that deposition of the organic carbon-rich (OR) zone (characterized by TOC >4%; located between 2393 m and 2406.5 m core depth) in the studied Marcellus Shale core was coincident with tectonically active and magmatic quiescent period of the Acadian orogeny (ca. 395–380 Ma). This time period also corresponds to the highest rate of mountain building in the Acadian Orogeny. The light rare earth (LREE) and selected trace elemental (e.g., Ta, Cs) composition of the OR zone sediments is similar to that of the bulk continental crust, supporting the lack of magmatic activity in the source area (i.e. Acadian Orogeny). In contrast, subsequent deposition of the organic carbon-poor (OP) sediments (characterized by TOC <4%; located between 2376 m and 2393 m core depth) in the upper Marcellus Shale occurred synchronously with a magmatic active phase (ca. 380–370 Ma) during the Acadian orogeny. The OP zone sediments have LREE and trace elemental composition similar to the average of the upper continental crust, suggesting intrusion of granodiorite rocks during a magmatic active period of Acadian Orogeny. The temporal and geochemical correlation between the Acadian orogenesis and the Marcellus deposition provide evidence for the role of tectonism in the enrichment of organic matter in the Marcellus Shale. 相似文献
18.
Ever since a breakthrough of marine shales in China, lacustrine shales have been attracting by the policy makers and scientists. Organic-rich shales of the Middle Jurassic strata are widely distributed in the Yuqia Coalfield of northern Qaidam Basin. In this paper, a total of 42 shale samples with a burial depth ranging from 475.5 m to 658.5 m were collected from the Shimengou Formation in the YQ-1 shale gas borehole of the study area, including 16 samples from the Lower Member and 26 samples from the Upper Member. Geochemistry, reservoir characteristics and hydrocarbon generation potential of the lacustrine shales in YQ-1 well were preliminarily investigated using the experiments of vitrinite reflectance measurement, maceral identification, mineralogical composition, carbon stable isotope, low-temperature nitrogen adsorption, methane isothermal adsorption and rock eval pyrolysis. The results show that the Shimengou shales have rich organic carbon (averaged 3.83%), which belong to a low thermal maturity stage with a mean vitrinite reflectance (Ro) of 0.49% and an average pyrolytic temperature of the generated maximum remaining hydrocarbon (Tmax) of 432.8 °C. Relative to marine shales, the lacustrine shales show low brittleness index (averaged 34.9) but high clay contents (averaged 55.1%), high total porosities (averaged 13.71%) and great Langmuir volumes (averaged 4.73 cm−3 g). Unlike the marine and marine-transitional shales, the quartz contents and brittleness index (BI) values of the lacustrine shales first decrease then increase with the rising TOC contents. The kerogens from the Upper Member shales are dominant by the oil-prone types, whereas the kerogens from the Lower Member shales by the gas-prone types. The sedimentary environment of the shales influences the TOC contents, thus has a close connection with the hydrocarbon potential, mineralogical composition, kerogen types and pore structure. Additionally, in terms of the hydrocarbon generation potential, the Upper Member shales are regarded as very good and excellent rocks whereas the Lower Member shales mainly as poor and fair rocks. In overall, the shales in the top of the Upper Member can be explored for shale oil due to the higher free hydrocarbon amount (S1), whereas the shales in the Lower Member and the Upper Member, with the depths greater than 1000 m, can be suggested to explore shale gas. 相似文献
19.
The paper takes the Upper Carboniferous Taiyuan shale in eastern uplift of Liaohe depression as an example to qualitatively and quantitatively characterize the transitional (coal-associated coastal swamp) shale reservoir. Focused Ion Beam Scanning Electron Microscope (FIB-SEM), nano-CT, helium pycnometry, high-pressure mercury intrusion and low-pressure gas (N2 & CO2) adsorption for eight shale samples were taken to investigate the pore structures. Four types of pores, i.e., organic matter (OM) pores, interparticle (InterP) pores, intraparticle (IntraP) pores and micro-fractures are identified in the shale reservoir. Among them, intraP pores and micro-fractures are the major pore types. Slit-shaped pores are the major shape in the pore system, and the connectivity of the pore-throat system is interpreted to be moderate, which is subordinate to marine shale. The porosity from three dimension (3D) reconstruction of SEM images is lower than the porosity of helium pycnometry, while the porosity trend of the above two methods is the same. Combination of mercury intrusion and gas absorption reveals that nanometer-scale pores provide the main storage space, accounting for 87.16% of the pore volume and 99.85% of the surface area. Micropores contribute 34.74% of the total pore volume and 74.92% of the total pore surface area; and mesopores account for 48.27% of the total pore volume and 24.93% of the total pore surface area; and macropores contribute 16.99% of the total pore volume and 0.15% of the total pore surface area. Pores with a diameter of less than 10 nm contribute the most to the pore volume and the surface area, accounting for 70.29% and 97.70%, respectively. Based on single factor analysis, clay minerals are positively related to the volume and surface area of micropores, mesopores and macropores, which finally control the free gas in pores and adsorbed gas content on surface area. Unlike marine shale, TOC contributes little to the development of micropores. Brittle minerals inhibit pore development of Taiyuan shale, which proves the influence of clay minerals in the pore system. 相似文献
20.
Much attention have been recently paid to the upper Ordovician Wufeng shale (O3w) and lower Silurian Longmaxi shale (S1l) in the Jiaoshiba area of Sichuan Basin, which is now the largest producing shale gas field in China. Field emission scanning electron microscopy (FE-SEM), low pressure gas (N2 and CO2) adsorption, helium pycnometry, X-ray diffraction and geochemical analyses were performed to investigate the pore structure and fractal dimension of the pores in O3w-S1l shale formation in the Jiaoshiba area. FE-SEM images show that organic matter (OM) pores are dominant in the organic-rich samples and these pores are often irregular, bubble-like, elliptical and faveolate in shape, while in organic-poor samples, limited and isolated interparticle (interP), intraparticle (intraP) and OM pores are observed. Reversed S-shaped isotherms obtained from nitrogen adsorption are type Ⅱ, and hysteresis loops indicate that the shape of micropore in the samples is slit-or plate-like. BET surface areas and total pore volume vary from 12.2 to 27.1 m2/g and from 1.8 × 10−2 to 2.9 × 10−2 cm3/g, with an average of 19.5 m2/g and 2.3 × 10−2 cm3/g, respectively. Adsorption volume from both N2 and CO2 adsorption increases with respect to TOC contents. Porosities obtained from helium porosimetry are comparable with these from gas (CO2 and N2) adsorption in O3w-S1l shale. However, porosity determined by quantitative FE-SEM analysis is much smaller, which is mainly related to limited resolution and the small areas of investigation.Based on the Frenkel-Halsey-Hill (FHH) model of low-pressure N2 adsorption, fractal dimensions of the pores varied from 2.737 to 2.823. Relationships between pore structure parameters and TOC content, mineral composition and fractal dimension reveal that the fractal dimension is mainly associated with micropores. Samples with higher TOC content, higher quartz content and lower clay content tend to contain more heterogeneous micropores, resulting in higher fractal dimensions and more complicated pore structure in shales. Therefore, fractal dimension is an effective parameter to reflect the complexity of pore structure and the degree of micropore development in O3w-S1l shale. 相似文献