共查询到19条相似文献，搜索用时 882 毫秒
1.
在进行裂隙岩体非饱和渗流研究中,选用合理的裂隙岩体毛管压力-饱和度关系曲线非常关键。基于裂隙岩体非饱和渗流特点,简述当前国内外非饱和裂隙岩体毛管压力-饱和度关系曲线模型的研究状况。总结出非饱和裂隙渗透具有毛细管流、薄膜流、优先流、裂隙-基质相互作用和沟槽流特点;分析了建立单裂隙岩体非饱和渗流毛管压力-饱和度关系曲线模型的主要方法,包括物模试验法、数值计算法和数学推导法,并归纳这些方法的计算结果;最后,结合渗流特点,对各种曲线模型结果进行比较,进一步分析得出：(1) 目前的曲线关系均建立在毛管理论基础之上,几乎没有反映渗流其他特点的关系曲线;(2) 运用数值计算法和数学推导建立曲线模型较为简便;(2) 在排水曲线初始时段,Brooks-Corey(BC)模型模拟得到的结果比van Genuchten(VG)模型要好些,而在末尾时段VG模型要好些。 相似文献
2.
3.
4.
《岩土力学》2017,(11):3332-3340
针对裂隙岩体的非饱和渗流问题,基于离散裂隙网络模型并结合非饱和Darcy定律、Richards方程、非饱和本构模型以及Signorini型饱和-非饱和互补溢出边界,提出了离散裂隙网络非饱和渗流问题的数学模型。采用有限单元法建立了裂隙网络非饱和渗流模型的数值求解格式和对应的迭代算法。通过与矩形坝稳定渗流、一维竖直裂隙非饱和入渗以及室内二维瞬态排水渗流的试验、数值及理论结果对比分析,验证了文中算法的有效性;根据流量等效原则,指出了裂隙网络模型应用于求解连续介质非饱和渗流问题的有效性。验证了该算法对于求解裂隙边坡降雨入渗问题的可靠性,揭示了降雨入渗过程裂隙网络流量分布的非均匀性及裂隙产状对降雨入渗流动具有重要的控制作用。 相似文献
5.
交叉裂隙作为裂隙网络的基本结构是控制场地尺度非饱和渗流特性的关键。随着流量的减小,交叉裂隙非饱和渗流将从连续、稳定的线状流转变为非连续、非稳定的滴状流,但目前对后者的研究还很少。在滴状流条件下,开展了交叉裂隙非饱和流动特性的理论和试验研究,发现了交叉裂隙滴状流存在毛细力驱动以及重力与毛细力联合驱动两种分流驱动模式。基于瞬态静力平衡方法,提出了一套液滴分流理论及计算模型,实现了动态分流过程的定量化描述与预测。结合模型预测与可视化试验,详细探究了两种模式下液滴的分流过程,阐明了动态分流行为受重力、毛细力、黏滞力共同控制的细观机制,并揭示了液滴长度、裂隙倾角、通道中液体的累积等因素对界面流速、分流体积比例的影响。研究成果为低流量、低饱和度条件下非饱和裂隙岩体渗流的预测与控制提供了理论及试验支撑。 相似文献
6.
仵彦卿 《水文地质工程地质》1997,(5)
岩体是由裂隙和其间的岩块组成。当岩块处于近乎隔水状态时，岩体中的渗流可看作为裂隙网络流。本文通过分析岩体裂隙网络渗流场、应力场以及它们之间的相互力学关系，提出了岩体渗流场与应力场耦合的裂隙网络模型及数值计算方法。 相似文献
7.
岩体水力学基础（五） 总被引：7，自引：0，他引：7
仵彦卿 《水文地质工程地质》1997,24(5):41-45
岩体是由裂隙和其间的岩块组成。当岩块御于近乎隔水状态时，岩体中的渗流可看作裂隙网络流。本文通过分析岩体裂隙网络渗流场、应力场以及它们之间的相互力学关系，提出了岩体渗流与应力场耦合的裂隙网络模型及数值计算方法。 相似文献
8.
裂隙岩体渗流概念模型研究 总被引：31，自引：4，他引：27
裂隙岩体中的渗流和传统的多孔介质渗流在机理上存在本质的差别,这种差别主要表现为裂隙岩体在各种尺度上存在的非均质性。模拟裂隙岩体渗流的主要困难在于描述这种非均质性。目前的概念模型,包括等效连续体模型、离散裂隙网络模型和混合模型使用了不同的技术来预测裂隙岩体中的渗流。这些模型基于不同的假设和概念框架,有着各自不同的优缺点。在实际应用时,应当根据研究域的具体特点和所要解决的问题的要求对其选择,此外,还讨论了单裂隙的概念模型。 相似文献
9.
裂隙岩体中的渗流规律与传统多孔介质渗流规律存在本质的区别,裂隙岩体渗流具有不均匀性、各向异性和非连续性等特点,如何更好地刻画裂隙水渗流的这种特点是当前裂隙水数值模拟的热点与难点。介绍了裂隙岩体地下水渗流特性,对目前裂隙水渗流模型及其优缺点进行比较、分析,同时对主流数值计算方法和数值模拟软件进行概括介绍。 相似文献
10.
基于COMSOL Multiphysics软件对非饱和裂隙土降雨入渗特性进行数值模拟研究。通过将裂隙和基质分别离散成有限单元,建立了能充分模拟土中裂隙流、基质流以及裂隙-基质流量交换的离散裂隙-孔隙介质模型。结合"空气单元"的概念,对裂隙土的上边界进行模拟。该方法不仅能描述降雨初期雨水沿裂隙优先入渗的现象,还能描述当降雨量大于裂隙土入渗量时雨水沿地表流走的现象。通过对地表以下2 m深度内低渗含裂隙土体进行模拟,分析了裂隙的几何特征、基质的水力特性、前期水分条件以及降雨强度对非饱和裂隙土降雨入渗过程的影响。结果表明,在非饱和裂隙土中,存在两个主要的渗流过程:一是水沿裂隙优先流动;二是水不断从裂隙吸入基质中,基质吸收水的作用抑制了裂隙中优势流的发展。与裂隙的几何特征相比,基质的水力特性对非饱和裂隙土渗流的影响较大。增大基质的饱和渗透系数可能使由裂隙流主导的渗流过程转变为由基质流主导的渗流过程,而基质的非饱和特性与裂隙土的初始含水率改变了土体的储水能力,从而加速或延缓了降雨入渗至某一深度的时间。降雨强度对土体入渗速率和入渗量均有影响,当超过裂隙土的入渗能力时,多余积水沿地表流走,断面入渗率随... 相似文献
11.
包气带水分入渗过程受多种因素的影响。定量研究层状非均质岩性结构和入渗速率对其影响,有助于解决根据不同条件选择单相流模型或水气二相流模型模拟包气带水分入渗过程的问题。结合填埋场等场地地层条件及污废水入渗特征,分别建立了“上细下粗”和“上粗下细”包气带层状非均质岩性结构水分入渗单相流和水气二相流模型,探讨不同层状非均质岩性结构条件下模型的适用性。在“上粗下细”岩性结构模型基础上,进一步探究入渗速率对水气两相运移结果的影响。基于论文模型研究表明:（1）在包气带岩性结构为“上细下粗”的条件下,气相的影响基本可以忽略,可直接采用单相流模型对包气带水分运移进行模拟;在“上粗下细”岩性结构和本次模型设定的底部压力保持不变及污废水泄漏前场地未接受降水入渗补给等条件下,当包气带上下层介质渗透率比值大于16倍时,气相会对水相运移产生明显影响,且下层介质渗透率越小、上下层介质渗透率比值越大,单相流与两相流的运移结果差别越大,需要采用水气二相流模型模拟包气带水分运移。（2）在包气带“上粗下细”岩性结构条件下,入渗速率越大,气相对水流入渗的阻滞作用越明显,此时包气带水分运移模拟应采用水气二相流模型。 相似文献
12.
13.
S. O. Grinevskii 《Moscow University Geology Bulletin》2011,66(3):189-201
This paper considers models of the transpiration root water uptake and principles for substantiating their parameters when
calculating unsaturated flow in the vadose zone and estimating infiltration groundwater recharge. The possible use of generalized
parameters for different landscape and soil conditions is substantiated based on analyzing the natural patterns of water balance
formation in the vadose zone and the sensitivity of transpiration models. Recommendations are given for selecting the models
of transpiration water uptake and substantiating their parameters, which enables one to minimize the errors in estimating
infiltration groundwater recharge. 相似文献
14.
Two numerical models, one for the vadose zone and the other for the aquifer system, are utilized to predict nitrate pollution
potential in groundwater. Transport by dispersion and convection of mobile species of nitrogen, ammonium ion exchange, first
order nitrogen transformations, and nitrogen plant uptake are included in the formulation for the vadose zone. Transport of
nitrate in the aquifer is assumed to be affected only by dispersion-convection phenomena. Justifications for one-dimensional
conceptualization of flow in the vadose zone and two-dimensional representation for the aquifer, under various field conditions,
are presented. To illustrate the concept, a simple hypothetical problem is solved. The approach presented here provides an
efficient means of long-term simulation of large-scale field problems. 相似文献
15.
受气候变化和人类活动等因素的综合影响,地下水超采和含水层水量亏空已成为备受关注的全球性问题。为了弥补含水层水量亏空和促进地下水资源涵养,已探索出多种人为干预地下水补给的措施,其中通过河道开展地下水人工补给由于具有明显优势而受到重视。已有实践表明,受渗漏补给潜力和包气带调蓄能力等的限制,并不是所有河流或河段都适宜开展地下水人工补给工作。目前缺乏为大家广泛接受的适宜性评估方法。本研究以永定河生态补水为契机,以北京平原段河道和下伏含水层为研究区开展了案例研究,并用实测数据对研究结果进行了检验。应用指标体系法建立的适宜性评估模型（LMBGITSC模型）包括河床土地利用类型、河床介质类型、河床宽度、河床地形坡度、包气带介质类型、包气带厚度、包气带给水度、包气带水平渗透性等8个指标。案例研究结果表明,沿河流流向,通过河道渗漏补给地下水的适宜性由好变差（防渗河段除外）。该规律主要受渗漏补给潜力和包气带调蓄能力控制,因此适宜性也呈现出“阶梯式”演变规律。检验结果表明所建的评估方法适用性较好。该方法具有可移植性,因此也可为其他同类地区提供参考。 相似文献
16.
Fractures are both rough and irregular but can be expressed by a simple model concept of two smooth parallel plates and the associated cubic law governing discharge through saturated fractures. However, in natural conditions and in the intermediate vadose zone, these assumptions are likely violated. This paper presents a qualitative experimental study investigating the cubic law under variable saturation in initially dry free-draining discrete fractures. The study comprised flow visualisation experiments conducted on transparent replicas of smooth parallel plates with inlet conditions of constant pressure and differing flow rates over both vertical and horizontal inclination. Flow conditions were altered to investigate the influence of intermittent and continuous influx scenarios. Findings from this research proved, for instance, that saturated laminar flow is not likely achieved, especially in nonhorizontal fractures. In vertical fractures, preferential flow occupies the minority of cross-sectional area despite the water supply. Movement of water through the fractured vadose zone therefore becomes a matter of the continuity principle, whereby water should theoretically be transported downward at significantly higher flow rates given the very low degree of water saturation. Current techniques that aim to quantify discrete fracture flow, notably at partial saturation, are questionable. Inspired by the results of this study, it is therefore hypothetically improbable to achieve saturation in vertical fractures under free-draining wetting conditions. It does become possible under extremely excessive water inflows or when not free-draining; however, the converse is not true, as a wet vertical fracture can be drained. 相似文献
17.
M. O. Schwartz 《Environmental Geology》2006,50(2):237-249
The UNSAT-H, HELP3 and MACRO4.3 computer codes, which have been developed for simulating the water balance of the unsaturated zone of soils and unconsolidated sediments, are also capable simulating water flow in low-porosity media such as fractured rock. The codes can be used to model the ability of rocks and overlying soils in the vadose zone to protect the groundwater in the uppermost aquifer. The net infiltration rates simulated by the different codes are compared against recharge determined by the chloride-balance method in Namibia. The dual-permeability code MACRO4.3 was found to produce more realistic estimates of net infiltration than the UNSAT-H and HELP3 codes, which are based on a single-permeability or effective-continuum method. The net infiltration rate together with the water storage in the unsaturated zone and the groundwater depth are used to calculate the residence time of pore water in the unsaturated zone. This parameter determines the intrinsic vulnerability of the aquifer. 相似文献
18.
A continuous/discontinuous Galerkin framework for modeling coupled subsurface and surface water flow
Clint Dawson 《Computational Geosciences》2008,12(4):451-472
We consider conjunctive surface-subsurface flow modeling, where surface water flow is described by the shallow water equations
and ground water flow by Richards’ equation for the vadose zone. Coupling between the models is based on the continuity of
flux and water pressure. Numerical approximation of the coupled model using the framework of discontinuous Galerkin (DG) methods
is formulated. In the subsurface, the local discontinuous Galerkin (LDG) method is used to approximate ground water velocity
and hydraulic head; a DG method is also used to approximate surface water velocity and elevation. This approach allows for
a weak coupling of the models and the use of different approximating spaces and/or meshes within each regime. A simplified
LDG method based on continuous approximations to water head is also described. Numerical results that investigate physical
and numerical aspects of surface–subsurface flow modeling are presented.
This work was supported by National Science Foundation grant DMS-0411413. 相似文献
19.
Hydrochemical data for meteoric waters of the uplifted carbonate platform of northern Guam show that, contrary to recent models of lowstand diagenesis, phreatic dissolution is active beneath a 60–180 m thick vadose zone. Overland flow during high intensity rainfall events is focussed into surface detention ponds, which drain very rapidly via the epikarst and vertical fissures to the freshwater lens. We estimate that these waters contribute 13% of dissolved calcium in samples from pumping wells but may also deliver aggressive and/or organic-rich waters to the lens. Fast-flow vadose waters mix with lens-top waters to form fresher cap that discharges rapidly coastwards via cavernous porosity. Slower vadose percolation, sampled as cave drips, equilibrates with bedrock within the upper 30 m of the vadose zone, accounting for some 46% of dissolved calcium in the lens waters. The remaining 41% calcium is generated by net dissolution within the lens. 相似文献