首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献，搜索用时 399 毫秒
1.
Abstract Analogue flume experiments were conducted to investigate the transport and sedimentation behaviour of turbulent pyroclastic density currents. The experimental currents were scaled approximately to the natural environment in three ways: (1) they were fully turbulent; (2) they had a very wide range of particle sizes and associated Rouse numbers (the ratio of particle settling velocity to effective turbulent eddy velocity in the current); and (3) they contained particles of two different densities. Two sets of surge‐type experiments were conducted in a 5 m long, water‐filled lock‐exchange flume at five different volumetric particle concentrations from 0·6% to 23%. In one set (one‐component experiments), the currents contained just dense particles; in the other set (two‐component experiments), they contained both light and dense particles in equal volume proportions. In both sets of experiments, the population of each component had a log‐normal size distribution. In the two‐component experiments, the size range of the light particle population was selected in order to be in hydrodynamic equivalence with that of the dense particles. Dense particles were normally graded, both vertically and downstream, in the deposits from both sets of experiments. The mass loading (normalized to the initial mass of the suspension) and grain size of the dense component in the deposits decreased with distance from the reservoir and were insensitive to initial total particle concentration in the currents. On the other hand, in the two‐component experiments, the light particles were extremely sensitive to concentration. They were deposited in hydrodynamic equivalence with the dense particles from dilute currents, but were segregated efficiently at concentrations higher than a few per cent. With increasing particle concentration, the large, light particles were carried progressively further down the flume because of buoyancy effects. Deposits from the high‐concentration currents exhibited reverse vertical grading of the large, light particles. Efficient segregation of the light component was observed even if the bulk density of the current was less than that of the light particles. In both sets of experiments, marked inflexions in the rate of downstream decline in mass loading and maximum grain size of the dense component can be attributed to the presence of two different particle settling regimes in the flow: (1) particles with Rouse numbers >2·5, which did not respond to the turbulence and settled rapidly; and (2) particles with Rouse numbers <2·5, which followed the turbulent eddies and settled slowly. The results are applied to the transport and sedimentation dynamics of pyroclastic density currents that generate large, widespread ignimbrites. Field data fail to reveal significant departures from aerodynamic equivalence between pumice and lithic clasts in three such ignimbrites: the particulate loads of some large ignimbrites are transported principally in turbulent suspensions of low concentration. In some ignimbrites, the well‐developed inflexions in curves of maximum lithic (ML) size vs. distance can be attributed to the existence of distinct high and low Rouse number particle settling regimes that mark the transition from an overcharged state to one in which the residual particulate load is transported more effectively by turbulence.  相似文献   

2.
Dense gas-particle jets similar to collapsing eruption columns were generated by large-scale experiments. The column collapse resulted in a ground-hugging current forming stratified layers with bedding similar to natural pyroclastic density current deposits. At the impact of the collapsing column on the ground, a thick, massive bed was formed due to a high sedimentation rate that dumped turbulence due to high clast concentration. Down-current, flow expansion favoured turbulence and dilute gas-particle current that formed thin rippled layers deposited under traction. Experiments fed with fine ash (median size 0·066 mm) formed deposits without tractional structures, because fine particles, as other sedimentary fine material, is cohesive and exposes a limited surface to the shear stress. Experimental outcomes show that massive beds are formed where the sedimentation rate per unit width Srw exceeds the bedload transportation rate Qb by two orders of magnitude. A lower ratio generates traction at the base of the flow and formation of shear structures that increase in wavelength and height with a decreasing flux. This study presents a diagram that provides a useful addition for facies analysis of pyroclastic density currents, provided that deposits representing sustained sedimentation can be identified in the field. In the diagram a decrease in the Srw/Qb ratio corresponds to an increase in bedform size. Application of the diagram for hazard assessment purposes allows the reconstruction of the mass eruption rate of the Agnano–Monte Spina eruption at Campi Flegrei, which is the main variable defining the intensity of past eruptions, and of the Bingham rheology of the massive underflow of the Mercato pyroclastic density current at Vesuvius.  相似文献   

3.
Geological and volcanological studies were performed in the Herculaneum excavations, 7 km west of Vesuvius, Italy, to reconstruct the main features of the pyroclastic density currents and the temporal sequence of the ad 79 eruptive events that destroyed and buried the town. The identification of two distinctive marker beds allows correlation of these deposits with the better‐known sequences to the south of Vesuvius, along the dispersal axis of the Plinian fall deposit. Detailed observations from stratigraphic sections show that the pyroclastic density current deposits are characterized by several sedimentary facies, each recording different depositional and emplacement mechanisms. Facies analysis reveals both lateral and vertical variations from massive to stratified deposits, which can be related to the combined effects of flow dynamics and local irregularities of the substratum at centimetre or metre scales. These topographic irregularities enhanced turbulence and allowed rapid transition from non‐turbulent to turbulent transport within the flow. Fabric data from these deposits, both from roof tile orientations and anisotropy magnetic susceptibility (AMS) analyses carried out on some of the pyroclastic deposits, suggest that the pyroclastic density currents were strongly affected by the presence of buildings. These obstacles probably caused deflection and separation of flows into multiple lobes that moved in different directions.  相似文献   

4.
Flume experiments were performed to study the flow properties and depositional characteristics of high‐density turbidity currents that were depletive and quasi‐steady to waning for periods of several tens of seconds. Such currents may serve as an analogue for rapidly expanding flows at the mouth of submarine channels. The turbidity currents carried up to 35 vol.% of fine‐grained natural sand, very fine sand‐sized glass beads or coarse silt‐sized glass beads. Data analysis focused on: (1) depositional processes related to flow expansion; (2) geometry of sediment bodies generated by the depletive flows; (3) vertical and horizontal sequences of sedimentary structures within the sediment bodies; and (4) spatial trends in grain‐size distribution within the deposits. The experimental turbidity currents formed distinct fan‐shaped sediment bodies within a wide basin. Most fans consisted of a proximal channel‐levee system connected in the downstream direction to a lobe. This basic geometry was independent of flow density, flow velocity, flow volume and sediment type, in spite of the fact that the turbidity currents of relatively high density were different from those of relatively low density in that they exhibited two‐layer flow, with a low‐density turbulent layer moving on top of a dense layer with visibly suppressed large‐scale turbulence. Yet, the geometry of individual morphological elements appeared to relate closely to initial flow conditions and grain size of suspended sediment. Notably, the fans changed from circular to elongate, and lobe and levee thickness increased with increasing grain size and flow velocity. Erosion was confined to the proximal part of the leveed channel. Erosive capacity increased with increasing flow velocity, but appeared to be constant for turbidity currents of different grain size and similar density. Structureless sediment filled the channel during the waning stages of the turbidity currents laden with fine sand. The adjacent levee sands were laminated. The massive character of the channel fills is attributed to rapid settling of suspension load and associated suppression of tractional transport. Sediment bypassing prevailed in fan channels composed of very fine sand and coarse silt, because channel floors remained fully exposed until the end of the experiments. Lobe deposits, formed by the fine sand‐laden, high‐density turbidity currents, contained massive sand in the central part grading to plane parallel‐laminated sand towards the fringes. The depletive flows produced a radial decrease in mean grain size in the lobe deposits of all fans. Vertical trends in grain size comprised inverse‐to‐normal grading in the levees and in the thickest part of the lobes, and normal grading in the channel and fringes of the fine sandy fans. The inverse grading is attributed to a process involving headward‐directed transport of relatively fine‐grained and low‐concentrated fluid at the level of the velocity maximum of the turbidity current. The normal grading is inferred to denote the waning stage of turbidity‐current transport.  相似文献   

5.
火山碎屑密度流是一种危险的火山活动现象,也是一种重要的盆地物源供给方式,对其沉积机制的研究具有灾害预防和油气勘探的双重意义。松辽盆地东南隆起区九台营城煤矿地区白垩系营城组古火山机构保存良好,发育有典型的火山碎屑密度流沉积物。本文在精细刻画火山碎屑岩的岩石结构、沉积构造的基础上,运用薄片观察和沉积物粒度统计的方法,从物质来源、搬运机制和就位方式角度系统地分析了火山碎屑密度流的整个沉积过程,并结合国内外火山学、沉积学的研究进展探讨了不同浓度火山碎屑密度流的沉积机制。研究区内的火山碎屑密度流沉积物可以划分为五种微相:①块状熔结角砾凝灰岩微相;②无序含集块凝灰角砾岩微相;③逆粒序或双粒序角砾凝灰岩微相;④正粒序角砾凝灰岩微相;⑤韵律层理凝灰岩微相。第一种微相具有熔结结构,可能形成于高挥发分岩浆喷发柱的垮塌,火山碎屑密度流的就位温度较高;后四种微相具有正常火山碎屑岩结构,可能形成于火山口的侧向爆炸,火山碎屑密度流的就位温度中等。沉积块状熔结角砾凝灰岩微相的火山碎屑密度流具有黏性碎屑流的流体特征,沉积物整体冻结就位;沉积无序含集块凝灰角砾岩微相和逆粒序或双粒序角砾凝灰岩微相的火山碎屑密度流具有颗粒流的流体特征,沉积物整体冻结就位;沉积正粒序角砾凝灰岩微相和韵律层理凝灰岩微相的火山碎屑密度流具有湍流的流体特征,沉积物连续加积就位。火山碎屑密度流的颗粒浓度是一个连续变量,但流体性质可能会发生突变,稀释的火山碎屑密度流的沉积机制符合下部流动边界模型,稠密的火山碎屑密度流的沉积机制符合层流(碎屑流或颗粒流)模型。  相似文献   

6.
ABSTRACT Mud‐rich sandstone beds in the Lower Cretaceous Britannia Formation, UK North Sea, were deposited by sediment flows transitional between debris flows and turbidity currents, termed slurry flows. Much of the mud in these flows was transported as sand‐ and silt‐sized grains that were approximately hydraulically equivalent to suspended quartz and feldspar. In the eastern Britannia Field, individual slurry beds are continuous over long distances, and abundant core makes it possible to document facies changes across the field. Most beds display regular areal grain‐size changes. In this study, fining trends, especially in the size of the largest grains, are used to estimate palaeoflow and palaeoslope directions. In the middle part of the Britannia Formation, stratigraphic zones 40 and 45, slurry flows moved from south‐west and south towards the north‐east and north. Most zone 45 beds lens out before reaching the northern edge of the field, apparently by wedging out against the northern basin slope. Zone 40 and 45 beds show downflow facies transitions from low‐mud‐content, dish‐structured and wispy‐laminated sandstone to high‐mud‐content banded units. In zone 50, at the top of the formation, flows moved from north to south or north‐west to south‐east, and their deposits show transitions from proximal mud‐rich banded and mixed slurried beds to more distal lower‐mud‐content banded and wispy‐laminated units. The contrasting facies trends in zones 40 and 45 and zone 50 may reflect differing grain‐size relationships between quartz and feldspar grains and mud particles in the depositing flows. In zones 40 and 45, quartz grains average 0·30–0·32 mm in diameter, ≈ 0·10 mm coarser than in zone 50. The medium‐grained quartz in zones 40 and 45 flows may have been slightly coarser than the associated mud grains, resulting in the preferential deposition of quartz in proximal areas and downslope enrichment of the flows in mud. In zone 50 flows, mud was probably slightly coarser than the associated fine‐grained quartz, resulting in early mud sedimentation and enrichment of the distal flows in fine‐grained quartz and feldspar. Mud particles in all flows may have had an effective grain size of ≈ 0·25 mm. Both mud content and suspended‐load fallout rate played key roles in the sedimentation of Britannia slurry flows and structuring of the resulting deposits. During deposition of zones 40 and 45, the area of the eastern Britannia Field in block 16/26 may have been a locally enclosed subbasin within which the depositing slurry flows were locally ponded. Slurry beds in the eastern Britannia Field are ‘lumpy’ sheet‐like bodies that show facies changes but little additional complexity. There is no thin‐bedded facies that might represent waning flows analogous to low‐density turbidity currents. The dominance of laminar, cohesion‐dominated shear layers during sedimentation prevented most bed erosion, and the deposystem lacked channel, levee and overbank facies that commonly make up turbidity current‐dominated systems. Britannia slurry flows, although turbulent and capable of size‐fractionating even fine‐grained sediments, left sand bodies with geometries and facies more like those deposited by poorly differentiated laminar debris flows.  相似文献   

7.
Particle-laden turbulent flows, called dilute pyroclastic density currents, can be generated during explosive volcanic eruptions. They are the most hazardous events of interaction with buildings and human environments in volcanic areas. A qualitative comparison with the dusty turbulent shear currents generated after the Twin Towers collapse on September 11, 2001 shows that turbulent, multiphase flow-building interaction causes flow separation and recirculation around the buildings. This simple idea could be applied to dilute pyroclastic density currents, and improved in future by adhoc numerical simulations of flow-building interaction.  相似文献   

8.
Turbidity currents are turbulent, sediment‐laden gravity currents which can be generated in relatively shallow shelf settings and travel downslope before spreading out across deep‐water abyssal plains. Because of the natural stratification of the oceans and/or fresh water river inputs to the source area, the interstitial fluid within which the particles are suspended will often be less dense than the deep‐water ambient fluid. Consequently, a turbidity current may initially be denser than the ambient sea water and propagate as a ground‐hugging flow, but later reverse in buoyancy as its bulk density decreases through sedimentation to become lower than that of the ambient sea water. When this occurs, all or part of the turbidity current lofts to form a buoyant sediment‐laden cloud from which further deposition occurs. Deposition from such lofting turbidity currents, containing a mixture of fine and coarse sediment suspended in light interstitial fluid, is explored through analogue laboratory experiments complemented by theoretical analysis using a ‘box and cloud’ model. Particular attention is paid to the overall deposit geometry and to the distributions of fine and coarse material within the deposit. A range of beds can be deposited by bimodal lofting turbidity currents. Lofting may encourage the formation of tabular beds with a rapid pinch‐out rather than the gradually tapering beds more typical of waning turbidity currents. Lofting may also decouple the fates of the finer and coarser sediment: depending on the initial flow composition, the coarse fraction can be deposited prior to or during buoyancy reversal, while the fine fraction can be swept upwards and away by the lofting cloud. An important feature of the results is the non‐uniqueness of the deposit architecture: different initial current compositions can generate deposits with very similar bed profiles and grading characteristics, highlighting the difficulty of reconstructing the nature of the parent flow from field data. It is proposed that deposit emplacement by lofting turbidity currents is common in the geological record and may explain a range of features observed in deep‐water massive sands, thinly bedded turbidite sequences and linked debrites, depending on the parent flow and its subsequent development. For example, a lofting flow may lead to a well sorted, largely ungraded or weakly graded bed if the fines are transported away by the cloud. However, a poorly sorted, largely ungraded region may form if, during buoyancy reversal, high local concentrations and associated hindered settling effects develop at the base of the cloud.  相似文献   

9.
The Lower Cretaceous Britannia Formation (North Sea) includes an assemblage of sandstone beds interpreted here to be the deposits of turbidity currents, debris flows and a spectrum of intermediate flow types termed slurry flows. The term ‘slurry flow’ is used here to refer to watery flows transitional between turbidity currents, in which particles are supported primarily by flow turbulence, and debris flows, in which particles are supported by flow strength. Thick, clean, dish‐structured sandstones and associated thin‐bedded sandstones showing Bouma Tb–e divisions were deposited by high‐ and low‐density turbidity currents respectively. Debris flow deposits are marked by deformed, intraformational mudstone and sandstone masses suspended within a sand‐rich mudstone matrix. Most Britannia slurry‐flow deposits contain 10–35% detrital mud matrix and are grain supported. Individual beds vary in thickness from a few centimetres to over 30 m. Seven sedimentary structure division types are recognized in slurry‐flow beds: (M1) current structured and massive divisions; (M2) banded units; (M3) wispy laminated sandstone; (M4) dish‐structured divisions; (M5) fine‐grained, microbanded to flat‐laminated units; (M6) foundered and mixed layers that were originally laminated to microbanded; and (M7) vertically water‐escape structured divisions. Water‐escape structures are abundant in slurry‐flow deposits, including a variety of vertical to subvertical pipe‐ and sheet‐like fluid‐escape conduits, dish structures and load structures. Structuring of Britannia slurry‐flow beds suggests that most flows began deposition as turbidity currents: fully turbulent flows characterized by turbulent grain suspension and, commonly, bed‐load transport and deposition (M1). Mud was apparently transported largely as hydrodynamically silt‐ to sand‐sized grains. As the flows waned, both mud and mineral grains settled, increasing near‐bed grain concentration and flow density. Low‐density mud grains settling into the denser near‐bed layers were trapped because of their reduced settling velocities, whereas denser quartz and feldspar continued settling to the bed. The result of this kinetic sieving was an increasing mud content and particle concentration in the near‐bed layers. Disaggregation of mud grains in the near‐bed zone as a result of intense shear and abrasion against rigid mineral grains caused a rapid increase in effective clay surface area and, hence, near‐bed cohesion, shear resistance and viscosity. Eventually, turbulence was suppressed in a layer immediately adjacent to the bed, which was transformed into a cohesion‐dominated viscous sublayer. The banding and lamination in M2 are thought to reflect the formation, evolution and deposition of such cohesion‐dominated sublayers. More rapid fallout from suspension in less muddy flows resulted in the development of thin, short‐lived viscous sublayers to form wispy laminated divisions (M3) and, in the least muddy flows with the highest suspended‐load fallout rates, direct suspension sedimentation formed dish‐structured M4 divisions. Markov chain analysis indicates that these divisions are stacked to form a range of bed types: (I) dish‐structured beds; (II) dish‐structured and wispy laminated beds; (III) banded, wispy laminated and/or dish‐structured beds; (IV) predominantly banded beds; and (V) thickly banded and mixed slurried beds. These different bed types form mainly in response to the varying mud contents of the depositing flows and the influence of mud on suspended‐load fallout rates. The Britannia sandstones provide a remarkable and perhaps unique window on the mechanics of sediment‐gravity flows transitional between turbidity currents and debris flows and the textures and structuring of their deposits.  相似文献   

10.
Pyroclastic currents are catastrophic flows of gas and particles triggered by explosive volcanic eruptions. For much of their dynamics, they behave as particulate density currents and share similarities with turbidity currents. Pyroclastic currents occasionally deposit dune bedforms with peculiar lamination patterns, from what is thought to represent the dilute low concentration and fluid‐turbulence supported end member of the pyroclastic currents. This article presents a high resolution dataset of sediment plates (lacquer peels) with several closely spaced lateral profiles representing sections through single pyroclastic bedforms from the August 2006 eruption of Tungurahua (Ecuador). Most of the sedimentary features contain backset bedding and preferential stoss‐face deposition. From the ripple scale (a few centimetres) to the largest dune bedform scale (several metres in length), similar patterns of erosive‐based backset beds are evidenced. Recurrent trains of sub‐vertical truncations on the stoss side of structures reshape and steepen the bedforms. In contrast, sporadic coarse‐grained lenses and lensoidal layers flatten bedforms by filling troughs. The coarsest (clasts up to 10 cm), least sorted and massive structures still exhibit lineation patterns that follow the general backset bedding trend. The stratal architecture exhibits strong lateral variations within tens of centimetres, with very local truncations both in flow‐perpendicular and flow‐parallel directions. This study infers that the sedimentary patterns of bedforms result from four formation mechanisms: (i) differential draping; (ii) slope‐influenced saltation; (iii) truncative bursts; and (iv) granular‐based events. Whereas most of the literature makes a straightforward link between backset bedding and Froude‐supercritical flows, this interpretation is reconsidered here. Indeed, features that would be diagnostic of subcritical dunes, antidunes and ‘chute and pools’ can be found on the same horizon and in a single bedform, only laterally separated by short distances (tens of centimetres). These data stress the influence of the pulsating and highly turbulent nature of the currents and the possible role of coherent flow structures such as Görtler vortices. Backset bedding is interpreted here as a consequence of a very high sedimentation environment of weak and waning currents that interact with the pre‐existing morphology. Quantification of near‐bed flow velocities is made via comparison with wind tunnel experiments. It is estimated that shear velocities of ca 0·30 m.s?1 (equivalent to pure wind velocity of 6 to 8 m.s?1 at 10 cm above the bed) could emplace the constructive bedsets, whereas the truncative phases would result from bursts with impacting wind velocities of at least 30 to 40 m.s?1.  相似文献   

11.
The complexity of flow and wide variety of depositional processes operating in subaqueous density flows, combined with post‐depositional consolidation and soft‐sediment deformation, often make it difficult to interpret the characteristics of the original flow from the sedimentary record. This has led to considerable confusion of nomenclature in the literature. This paper attempts to clarify this situation by presenting a simple classification of sedimentary density flows, based on physical flow properties and grain‐support mechanisms, and briefly discusses the likely characteristics of the deposited sediments. Cohesive flows are commonly referred to as debris flows and mud flows and defined on the basis of sediment characteristics. The boundary between cohesive and non‐cohesive density flows (frictional flows) is poorly constrained, but dimensionless numbers may be of use to define flow thresholds. Frictional flows include a continuous series from sediment slides to turbidity currents. Subdivision of these flows is made on the basis of the dominant particle‐support mechanisms, which include matrix strength (in cohesive flows), buoyancy, pore pressure, grain‐to‐grain interaction (causing dispersive pressure), Reynolds stresses (turbulence) and bed support (particles moved on the stationary bed). The dominant particle‐support mechanism depends upon flow conditions, particle concentration, grain‐size distribution and particle type. In hyperconcentrated density flows, very high sediment concentrations (>25 volume%) make particle interactions of major importance. The difference between hyperconcentrated density flows and cohesive flows is that the former are friction dominated. With decreasing sediment concentration, vertical particle sorting can result from differential settling, and flows in which this can occur are termed concentrated density flows. The boundary between hyperconcentrated and concentrated density flows is defined by a change in particle behaviour, such that denser or larger grains are no longer fully supported by grain interaction, thus allowing coarse‐grain tail (or dense‐grain tail) normal grading. The concentration at which this change occurs depends on particle size, sorting, composition and relative density, so that a single threshold concentration cannot be defined. Concentrated density flows may be highly erosive and subsequently deposit complete or incomplete Lowe and Bouma sequences. Conversely, hydroplaning at the base of debris flows, and possibly also in some hyperconcentrated flows, may reduce the fluid drag, thus allowing high flow velocities while preventing large‐scale erosion. Flows with concentrations <9% by volume are true turbidity flows (sensu 4 ), in which fluid turbulence is the main particle‐support mechanism. Turbidity flows and concentrated density flows can be subdivided on the basis of flow duration into instantaneous surges, longer duration surge‐like flows and quasi‐steady currents. Flow duration is shown to control the nature of the resulting deposits. Surge‐like turbidity currents tend to produce classical Bouma sequences, whose nature at any one site depends on factors such as flow size, sediment type and proximity to source. In contrast, quasi‐steady turbidity currents, generated by hyperpycnal river effluent, can deposit coarsening‐up units capped by fining‐up units (because of waxing and waning conditions respectively) and may also include thick units of uniform character (resulting from prolonged periods of near‐steady conditions). Any flow type may progressively change character along the transport path, with transformation primarily resulting from reductions in sediment concentration through progressive entrainment of surrounding fluid and/or sediment deposition. The rate of fluid entrainment, and consequently flow transformation, is dependent on factors including slope gradient, lateral confinement, bed roughness, flow thickness and water depth. Flows with high and low sediment concentrations may co‐exist in one transport event because of downflow transformations, flow stratification or shear layer development of the mixing interface with the overlying water (mixing cloud formation). Deposits of an individual flow event at one site may therefore form from a succession of different flow types, and this introduces considerable complexity into classifying the flow event or component flow types from the deposits.  相似文献   

12.
The behaviour of subaerial particle-laden gravity currents (e.g. pyroclastic flows, lahars, debris flows, sediment-bearing floods and jökulhlaups) flowing into the sea has been simulated with analogue experiments. Flows of either saline solution, simple suspensions of silicon carbide (SiC) in water or complex suspensions of SiC and plastic particles in methanol were released down a slope into a tank of water. The excess momentum between subaerial and subaqueous flow is dissipated by a surface wave. At relatively low density contrasts between the tank water and the saline or simple suspensions, the flow mixture enters the water and forms a turbulent cloud involving extensive entrainment of water. The cloud then collapses gravitationally to form an underwater gravity current, which progresses along the tank floor. At higher density contrasts, the subaerial flow develops directly into a subaqueous flow. The flow slows and thickens in response to the reduced density contrast, which is driving motion, and then continues in the typical gravity current manner. Complex suspensions become dense flows along the tank floor or buoyant flows along the water surface, if the mixtures are sufficiently denser or lighter than water respectively. Flows of initially intermediate density are strongly influenced by the internal stratification of the subaerial flow. Material from the particulate-depleted upper sections of the subaerial flow becomes a buoyant gravity current along the water surface, whereas material from the particulate-enriched lower sections forms a dense flow along the tank floor. Sedimentation from the dense flow results in a reduction in bulk density until the mixture attains buoyancy, lifts off and becomes a secondary buoyant flow along the water surface. Jökulhlaups, lahars and debris flows are typically much denser than seawater and, thus, will usually form dense flows along the seabed. After sufficient sedimentation, the freshwater particulate mixture can lift off to form a buoyant flow at the sea surface, leading to a decoupling of the fine and coarse particles. Flood waters with low particulate concentrations (<2%) may form buoyant flows immediately upon entering the ocean. Subaerial pyroclastic flows develop a pronounced internal stratification during subaerial run-out and, thus, a flow-splitting behaviour is probable, which agrees with evidence for sea surface and underwater flows from historic eruptions of Krakatau and Mont Pelée. A pyroclastic flow with a bulk density closer to that of sea water may form a turbulent cloud, resulting in the deposition of much of the pyroclasts close to the shore. Dense subaqueous pyroclastic flows will eventually lift off and form secondary buoyant flows, either before or after the transformation to a water-supported nature.  相似文献   

13.
The origin of massive sands in turbidite successions has commonly been attributed to the rapid dumping of sand due to flow unsteadiness in collapsing, single surge-type, high-density turbidity currents. The general applicability of this model is questioned here, and we propose that rapid deposition of massive sands also occurs due to non-uniformity in prolonged, quasi-steady high-density turbidity currents. We attempt to eliminate ambiguity in the use of the terms ‘deceleration’and ‘unsteadiness’with respect to non-uniform sediment gravity flows, and stress that, as with any particulate current, unsteadiness is not a prerequisite of sediment deposition. We propose a mechanism of gradual aggradation of sand beneath a sustained steady or quasi-steady current, and upward-migration of a depositional flow boundary that is dominated by grain hyperconcentration and hindered settling. Formation of tractional structures is prevented by the absence of a sharp rheological interface between the lowest parts of the flow and the just-formed dewatering deposit. Deposition continues as long as the downward grain flux to the depositional flow boundary is balanced by grain supply from above or from upcurrent. Massive sand deposited in this way is not, strictly, a result of ‘direct suspension sedimentation’in that it is characterized by grain interactions, hindered settling, shear and, possibly, by interlocking of grains. The thickness of the resulting massive sand bears no relation to the thickness of the parental current, and the vertical variation within the deposit may reveal little about the vertical structure of the current, even during deposition. Thin, normally graded tops or mud drapes represent the eventual waning of sustained currents.  相似文献   

14.
Subaqueous sediment density flows: Depositional processes and deposit types   总被引：7，自引：0，他引：7  
Submarine sediment density flows are one of the most important processes for moving sediment across our planet, yet they are extremely difficult to monitor directly. The speed of long run‐out submarine density flows has been measured directly in just five locations worldwide and their sediment concentration has never been measured directly. The only record of most density flows is their sediment deposit. This article summarizes the processes by which density flows deposit sediment and proposes a new single classification for the resulting types of deposit. Colloidal properties of fine cohesive mud ensure that mud deposition is complex, and large volumes of mud can sometimes pond or drain‐back for long distances into basinal lows. Deposition of ungraded mud (TE‐3) most probably finally results from en masse consolidation in relatively thin and dense flows, although initial size sorting of mud indicates earlier stages of dilute and expanded flow. Graded mud (TE‐2) and finely laminated mud (TE‐1) most probably result from floc settling at lower mud concentrations. Grain‐size breaks beneath mud intervals are commonplace, and record bypass of intermediate grain sizes due to colloidal mud behaviour. Planar‐laminated (TD) and ripple cross‐laminated (TC) non‐cohesive silt or fine sand is deposited by dilute flow, and the external deposit shape is consistent with previous models of spatial decelerating (dissipative) dilute flow. A grain‐size break beneath the ripple cross‐laminated (TC) interval is common, and records a period of sediment reworking (sometimes into dunes) or bypass. Finely planar‐laminated sand can be deposited by low‐amplitude bed waves in dilute flow (TB‐1), but it is most likely to be deposited mainly by high‐concentration near‐bed layers beneath high‐density flows (TB‐2). More widely spaced planar lamination (TB‐3) occurs beneath massive clean sand (TA), and is also formed by high‐density turbidity currents. High‐density turbidite deposits (TA, TB‐2 and TB‐3) have a tabular shape consistent with hindered settling, and are typically overlain by a more extensive drape of low‐density turbidite (TD and TC,). This core and drape shape suggests that events sometimes comprise two distinct flow components. Massive clean sand is less commonly deposited en masse by liquefied debris flow (DCS), in which case the clean sand is ungraded or has a patchy grain‐size texture. Clean‐sand debrites can extend for several tens of kilometres before pinching out abruptly. Up‐current transitions suggest that clean‐sand debris flows sometimes form via transformation from high‐density turbidity currents. Cohesive debris flows can deposit three types of ungraded muddy sand that may contain clasts. Thick cohesive debrites tend to occur in more proximal settings and extend from an initial slope failure. Thinner and highly mobile low‐strength cohesive debris flows produce extensive deposits restricted to distal areas. These low‐strength debris flows may contain clasts and travel long distances (DM‐2), or result from more local flow transformation due to turbulence damping by cohesive mud (DM‐1). Mapping of individual flow deposits (beds) emphasizes how a single event can contain several flow types, with transformations between flow types. Flow transformation may be from dilute to dense flow, as well as from dense to dilute flow. Flow state, deposit type and flow transformation are strongly dependent on the volume fraction of cohesive fine mud within a flow. Recent field observations show significant deviations from previous widely cited models, and many hypotheses linking flow type to deposit type are poorly tested. There is much still to learn about these remarkable flows.  相似文献   

15.
Small-scale pyroclastic density currents (PDCs) associated with the AD 472 (Pollena) eruption of Somma-Vesuvius, Italy, were generated by both magmatic and phreatomagmatic explosive fragmentation. The resulting deposits were emplaced under flow boundary conditions dominated by varying combinations of grain interaction, fluid escape and traction processes. Stratigraphic and lithofacies analysis of these PDCs offers a new perspective on the en masse versus progressive aggradation debate for PDC deposition. In particular, the analyses indicate that PDCs were density stratified with a basal underflow dominated by grain interactions. The underflows comprised trains of self-organized granular pulses of variable thickness and magnitude, depending on the overall particle concentration and fluid turbulence. A change in gradient between the upper and lower slopes of the volcano promoted deposition and the different pulses aggraded sequentially (stepwise). In this model each pulse stops en masse and the whole deposit aggrades progressively. Particle concentration, density, mean velocity, and flow height were assessed for the studied PDCs using differaent methods for massive and stratified deposits. The calculated mobility of the flows was 0·2 to 0·3, in the expected range for small-scale PDCs.  相似文献   

16.
Emplacement of small‐volume (<0·1 km3) pyroclastic flows is significantly influenced by topography. The Arico ignimbrite on Tenerife (Canary Islands) is a characteristic small‐volume pyroclastic flow deposit emplaced on high relief topography. The pyroclastic flow flowed down pre‐existing valleys on the southern slopes of the island. In proximal areas deep (up to 100 m) valleys acted as efficient conduits for the pyroclastic flow, which was mostly channelled; in this particular area the ignimbrite corresponds to a homogeneous, moderately welded deposit, consisting of flattened pumices in an abundant ashy matrix with a relatively low lithic fragment content. In intermediate zones significant changes occur in the steepness of the slope and, although still channelled, here the pyroclastic flow was influenced by hydraulic jumps. In this area, two different units can be clearly distinguished in the ignimbrite: the lower unit is composed of a lithic‐rich ground‐layer deposit that formed at the turbulent, highly concentrated head of the flow; the upper unit consists of a well welded pumice‐rich deposit that occasionally reveals a basal layer formed by shearing with the lower part. This division into two units is maintained as far as distal areas near the present‐day coastline, where the slope is very gentle or null and the ignimbrite is not channelled. The ground layer is not found in distal areas. The ignimbrite here only consists of the upper unit, which is occasionally repeated due to a surging process provoked by the lower flow speed, as the pyroclastic flow spread out of the channelled zone. A theoretical model on how topography controlled the deposition of the Arico ignimbrite is derived by interpreting the observed lithological and sedimentological variations in terms of changes in topography and bedrock morphology. This new model is of general applicability and will help to explain other deposits of similar characteristics.  相似文献   

17.
本文将颗粒驱动重力流实验流体与自然界低密度火山碎屑流进行标度化研究,探讨低密度火山碎屑流的流动行为。通过在矩形流体交换水箱中放置占水箱宽度1/4、1/2、3/4比例的侧向遮挡障碍物,调查了颗粒驱动重力流实验流体在遇到侧向遮挡前后的运动模式、流体前锋速度减速特征和颗粒堆积分布特征。实验结果显示出不同比例的部分遮挡对低密度火山碎屑流影响的复杂性。实验表明,1/4比例的部分遮挡能够提高低密度火山碎屑流在通过之后的流速,并增加通过遮挡的颗粒堆积总量,能够解释日本云仙岳火山1991年6月3日喷发形成的碎屑流流动特征。在侧向遮挡比例为1/2时,~100T的时间内流体前锋减速,并在~100T之后加速（T为无量纲时间）;通过遮挡的堆积物总量明显减少。通过3/4比例的侧向遮挡之后,颗粒实验流体前锋持续减速,颗粒堆积总量减少。  相似文献   

18.
A process-based, forward computer model of turbidity current flow and sedimentation, termed the TCFS model, has been developed to trace the downslope evolution of individual turbidity flows. Details of the model itself have been presented in a preceding paper. We here outline a series of tests of the TGFS model. The sensitivity tests of the TCFS model to general geological controls reveal the quantitative relationship between these controls and the behaviour of turbidity flows and the geometry and textural features of the resulting turbidites. Experimental turbidity currents on relatively steep slopes accelerate more rapidly and reach higher velocities than those on gentle slopes. Flows with larger initial volumes have higher initial velocities, travel further downslope, and form beds of greater thickness and downslope extent than smaller flows. Experimental high-concentration flows with suspended-sediment concentrations of 25% accelerate more rapidly and reach higher downslope velocities than dilute flows with 5% suspended sediment. The higher velocities and enhanced hindered-settling effects of the high-concentration flows lead to much greater transport distances and reduced vertical and lateral sediment size grading in the resulting turbidites. Beds formed by experimental high-concentration flows are massive or show coarse-tail grading whereas beds formed by low-concentration flows show distribution-grading. Experimental flows fed by coarse sediment sources tend to deposit the bulk of their suspended sediment loads on the proximal slope, resulting in more rapid flow deceleration and sedimentation than flows fed by silt-rich, fine-grained sediment sources. Turbidites formed by coarse-sediment flows tend to have a wedge-shaped geometry, with low downslope extent and high surface relief, whereas turbidites formed by fine-sediment flows tend to have a tabular geometry, with greater downslope extent and lower surface relief. A specific geological test of the TCFS model is based on studies of modern turbidity currents in Bute Inlet, British Columbia, Canada. With the input initial and boundary conditions estimated from Bute Inlet, the model predicts the downslope velocity evolution of turbidity currents comparable to those of modern and ancient turbidity flows measured in Bute Inlet. Model-calculated vertical and downslope grain-size properties of turbidites are similar to those exhibited by surface and cored Bute Inlet turbidites. Model flows tend to decelerate more rapidly than some stronger turbidity currents in the Bute Inlet system, and model beds tend to decrease in grain-size downslope more rapidly than observed bottom sediments. This is probably because the TCFS model flows lacked clay, which is abundant in Bute Inlet; they do not fully simulate turbulent mixing of suspended sediments; and they better represent the unsteady, depositional stage of turbidity-currents than the preceding stage of more-or-less steady-flow conditions. These tests demonstrate that the TCFS model provides a semi-quantitative method to study the growth patterns of submarine turbidite systems. It can serve as a predictive tool for analysing the facies architecture of ancient turbidite systems through simulating multi-depositional events by improving its erosion function, and the compatibility between its numerical components.  相似文献   

19.
Ignimbrite flow units commonly show reverse grading of large pumice clasts and normal grading of large lithic clasts. Ignimbrites show coarse-tail grading, in which particles beneath a critical diameter, ranging from 64 to 2 mm, are ungraded. Above this size the larger the clast diameter the more pronounced the segregation. The grading is consistent with the theoretical settling rates of particles in a dispersion with a high particle concentration. Ignimbrite flow units show a reversely graded, fine grained basal layer which is attributed to the action of boundary forces during flow. Ignimbrites are commonly associated with cross-stratified pyroclastic surge deposits and fine ash fall deposits formed in the same eruption. The fine ash fall deposit is depleted in crystals and is thought to be the deposit of the fine turbulent cloud observed making up the upper parts of nuées ardentes. Pyroclastic flows are postulated to be dense, poorly expanded partly fluidized debris flows. Only its fine grained components can be fluidized by gas. Pyroclastic flows are believed to behave as a dispersion of larger clasts in a medium of fluidized fines, which acts as a lubricant similar to water in mud-flows. Poor sorting in ignimbrites is attributed to high particle concentrations not turbulence. Many pyroclastic flows may be laminar in their movement with apparent viscosities, deduced from the lateral grading of large lithic clasts, in the range 101?103 poise.  相似文献   

20.
The Cretaceous Kusandong Tuff, Korea, is a thin (1–5 m thick) but laterally extensive (~ 200 km) silicic ignimbrite emplaced in a fluviolacustrine basin adjacent to a continental volcanic arc. The tuff has been used as an excellent key bed because of its great lateral continuity and unique lithology, characterized by the virtual absence of juvenile clasts and an abundance of quartz and feldspar crystals (up to 55–73 vol.%). The tuff is mostly massive and ungraded and locally shows crude internal layering, basal inverse grading and near-top normal grading of crystals, either erosional or non-erosional lower surfaces, and flat-lying to imbricated grain fabrics. Fragile intraformational clasts of mudstone and tuff are also included. These features provide only ambiguous information on the properties of the responsible pyroclastic density currents: i.e. whether they were dense and laminar or dilute and turbulent. The overall lateral continuity and sheet-like geometry of the tuff suggests, however, that the transport system of the currents was highly expanded, dilute, and turbulent. A plug-flow or slab-flow model cannot explain the origin of crude internal layering, imbricated grain fabrics, and the high crystal content, which is most likely the result of vigorous sorting processes within a dilute and turbulent current. Features indicative of deposition from a dense and laminar transporting medium are locally present, suggesting that a dense and laminar depositional system could develop locally at the base of the dilute and turbulent transport system. The virtual absence of juvenile clasts in the tuff is interpreted to be due to rapid ascent, sudden decompression, and full fragmentation of silicic magma into fine glass shards and crystals. Scarcity of basement-derived accidental components together with the absence of pumiceous fallout deposits beneath the tuff is interpreted to be due to shallow-level fragmentation of magma followed by immediate generation of pyroclastic density currents from shallow-level blasts at the onset of eruption. The eruption occurred through multiple vent sites in a short period of time, producing a seemingly single but actually composite ignimbrite unit. Such an eruption was probably possible because of a regional tectonic event within the basin or in its vicinity. It is proposed that a composite ignimbrite with the characteristics of the Kusandong Tuff can be an exemplary product of syntectonic volcanism that can provide an insight into the interpretation of structural and stratigraphic evolution of a sedimentary basin.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号