首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献,搜索用时 868 毫秒
1.
2.
Two ground penetrating radar (GPR) techniques were used to estimate the shallow soil water content at the field scale. The first technique is based on the ground wave velocity measured with a bistatic impulse radar connected to 450 MHz ground-coupled antennas. The second technique is based on inverse modeling of an off-ground monostatic TEM horn antenna in the 0.8–1.6 GHz frequency range. Data were collected on a 8 by 9 m partially irrigated intensive research plot and along four 148.5 m transects. Time domain reflectometry, capacitance sensors, and volumetric soil samples were used as reference measurements. The aim of the study was to test the applicability of the ground wave method and the off-ground inverse modeling approach at the field scale for a soil with a silt loam texture. The results for the ground wave technique were difficult to interpret due to the strong attenuation of the GPR signal, which is related to the silt loam texture at the test site. The root mean square error of the ground wave technique was 0.076 m3 m−3 when compared to the TDR measurements and 0.102 m3 m−3 when compared with the volumetric soil samples. The off-ground monostatic GPR measured less within-field soil water content variability than the reference measurements, resulting in a root mean square error of 0.053 m3 m−3 when compared with the TDR measurements and an error of 0.051 m3 m−3 when compared with the volumetric soil samples. The variability between the two GPR measurements was even larger with a RSME of 0.115 m3 m−3. In summary, both GPR methods did not provide adequate spatial information on soil water content variation at the field scale. The main reason for the deviating results of the ground wave method was the poor data quality due to high silt and clay content at the test site. Additional reasons were shallow reflections and the dry upper soil layer that cannot be detected by the ground wave method. In the case of off-ground GPR, the high sensitivity to the dry surface layer is the most likely reason for the observed deviations. The off-ground GPR results might be improved by using a different antenna that allows data acquisition in a lower frequency range.  相似文献   

3.
Ground penetrating radar (GPR) is currently within the scope of China's Chang-E 3 lunar mission, to study the shallow subsurface of the Moon. In this study, key factors that could affect a lunar GPR performance, such as frequency, range resolution, and antenna directivity, are discussed firstly. Geometrical optics and ray tracing techniques are used to model GPR echoes, considering the transmission, attenuation, reflection, geometrical spreading of radar waves, and the antenna directivity. The influence on A-scope GPR echoes and on the simulated radargrams for the Sinus Iridum region by surface and subsurface roughness, dielectric loss of the lunar regolith, radar frequency and bandwidth, and the distance between the transmit and receive antennas are discussed. Finally, potential scientific return about lunar subsurface properties from GPR echoes is also discussed. Simulation results suggest that subsurface structure from several to hundreds of meters can be studied from GPR echoes at P and VHF bands, and information about dielectric permittivity and thickness of subsurface layers can be estimated from GPR echoes in combination with regolith composition data.  相似文献   

4.
Previous studies of ground ice using moveout type ground-penetrating radar (GPR) surveys indicate that the dielectric permittivity can constrain the type of ground ice present in the subsurface. Due to the high-loss nature of the active layer over permafrost targets, however, the signal strength of GPR signals is often insufficient to resolve the basal boundary required for determining the dielectric permittivity of an underlying unit. We apply a non-conventional antenna orientation and post-processing method to determine the dielectric permittivity of the unit underlying the lowest resolvable boundary. We conduct moveout surveys using a 450 MHz GPR with collinear parallel oriented antennas on two adjacent ground ice formations in the region of Thomas Lee Inlet, Devon Island, Nunavut. We exploit the Brewster angle to calculate the approximate dielectric permittivity of ground ice formations below the active layer. The results agree within 1 dielectric unit with on-ice permittivity measurements made during a complementary study of the site.  相似文献   

5.
Ballast fouling is created by the breakdown of aggregates or outside contamination by coal dust from coal trains, or from soil intrusion beneath rail track. Due to ballast fouling, the conditions of rail track can be deteriorated considerably depending on the type of fouling material and the degree of fouling. So far there is no comprehensive guideline available to identify the critical degree of fouling for different types of fouling materials. This paper presents the identification of degree of fouling and types of fouling using non-destructive testing, namely seismic surface-wave and ground penetrating radar (GPR) survey. To understand this, a model rail track with different degree of fouling has been constructed in Civil engineering laboratory, University of Wollongong, Australia. Shear wave velocity obtained from seismic survey has been employed to identify the degree of fouling and types of fouling material. It is found that shear wave velocity of fouled ballast increases initially, reaches optimum fouling point (OFP), and decreases when the fouling increases. The degree of fouling corresponding after which the shear wave velocity of fouled ballast will be smaller than that of clean ballast is called the critical fouling point (CFP). Ground penetrating radar with four different ground coupled antennas (500 MHz, 800 MHz, 1.6 GHz and 2.3 GHz) was also used to identify the ballast fouling condition. It is found that the 800 MHz ground coupled antenna gives a better signal in assessing the ballast fouling condition. Seismic survey is relatively slow when compared to GPR survey however it gives quantifiable results. In contrast, GPR survey is faster and better in estimating the depth of fouling.  相似文献   

6.
GPR (Ground Penetrating Radar) results are shown for perpendicular broadside and parallel broadside antenna orientations. Performance in detection and localization of concrete tubes and steel tanks is compared as a function of acquisition configuration. The comparison is done using 100 MHz and 200 MHz center frequency antennas. All tubes and tanks are buried at the geophysical test site of IAG/USP in São Paulo city, Brazil. The results show that the long steel pipe with a 38-mm diameter was well detected with the perpendicular broadside configuration. The concrete tubes were better detected with the parallel broadside configuration, clearly showing hyperbolic diffraction events from all targets up to 2-m depth. Steel tanks were detected with the two configurations. However, the parallel broadside configuration was generated to a much lesser extent an apparent hyperbolic reflection corresponding to constructive interference of diffraction hyperbolas of adjacent targets placed at the same depth. Vertical concrete tubes and steel tanks were better contained with parallel broadside antennas, where the apexes of the diffraction hyperbolas better corresponded to the horizontal location of the buried target disposition. The two configurations provide details about buried targets emphasizing how GPR multi-component configurations have the potential to improve the subsurface image quality as well as to discriminate different buried targets. It is judged that they hold some applicability in geotechnical and geoscientific studies.  相似文献   

7.
In the field of road construction and maintenance, the need for information on the thickness of very thin road layers is not satisfied by means of commercial pulse GPR, due to the inability of such devices to operate over ranges of several gigahertz. As a result, research has focused on the design of a step-frequency radar technique, able to work with very high-frequency synthetic pulses.An ultrawide band antenna, belonging to the family of Vivaldi antennas, has been developed for road applications. It has been created using stripline technology and yields a band width greater than one decade. During an initial step, this antenna was tested on various bituminous concrete samples with a network analyzer. Different parameters were studied, including band width, offset between antennas, and height and shape of the frequency-dependent pulse.A second step involved GPR dynamic measurements. A customized software program enabled recording data from the network analyzer. Several radar profiles were developed from selected road construction and maintenance test sites (e.g. the Circular Pavement Fatigue Test Track, composed of a number of known structures). Results show improved resolution when compared to a commercial impulse GPR system.  相似文献   

8.
In arctic streams, depth of thaw beneath the stream channel is likely a significant parameter controlling hyporheic zone hydrology and biogeochemical cycling. As part of an interdisciplinary study of this system, we conducted a field investigation to test the effectiveness of imaging substream permafrost using ground‐penetrating radar (GPR). We investigated three sites characterized by low‐energy water flow, organic material lining the streambeds, and water depths ranging from 0·2 to 2 m. We acquired data using a 200 MHz pulsed radar system with the antennas mounted in the bottom of a small rubber boat that was pulled across the stream while triggering the radar at a constant rate. We achieved excellent results at all three sites, with a clear continuous image of the permafrost boundary both peripheral to and beneath the stream. Our results demonstrate that GPR can be an effective tool for measuring substream thaw depth. Copyright © 2005 John Wiley & Sons, Ltd.  相似文献   

9.
Since target reflections directly depend on the emitted pulse characteristics, a key factor for carrying out a successful GPR survey is to know as much as possible about the transmission features of the antennas used. This information is very important in order to choose the right antennas and set the appropriate configuration parameters for a specific survey. With this in mind this paper deals with the development of a set of laboratory experiments on the resolution capabilities of three bowtie antennas at frequencies of 500, 800 and 1000 MHz. Results from these measurements give a first estimation of the resolution of the antennas under test, showing the advantage of performing experiments rather than relying only on theoretical assumptions. The results are also expressed in terms of the central wavelength for each antenna and compared with some theoretical estimations proposed in the specialized bibliography.  相似文献   

10.
Corrosion associated with reinforcing bars is the most significant contributor to bridge deficiencies. The corrosion is usually caused by moisture and chloride ion exposure. The reinforcing bars are attacked by corrosion and yield expansive corrosion products. These oxidation products occupy a larger volume than the original intact steel and internal expansive stresses lead to cracking and debonding. There are some conventional inspection methods for the detection of the reinforcing bar's corrosion but they can be invasive and destructive, often laborious, and lane closure is required and it is difficult or unreliable for any quantification of corrosion. For these reasons, bridge engineers always prefer more to use the ground penetrating radar (GPR) technique. In this work a novel numerical approach for three dimensional tracking and mapping of cracks in the bridge is proposed. The work starts from some interesting results based on the use of the 3D imaging technique in order to improve the potentiality of the GPR to detect voids, cracks or buried objects. The numerical approach has been tested on data acquired on a bridge by using a pulse GPR system specifically designed for bridge deck and pavement inspection. The equipment integrates two arrays of Ultra Wide Band ground coupled antennas, having a main working frequency of 2 GHz. The two arrays are using antennas arranged with a different polarization. The cracks, associated often to moisture increase and higher values of the dielectric constant, produce a not negligible increase of the signal amplitude. Following this, the algorithm, organized in preprocessing, processing and postprocessing stages, analyzes the signal by comparing the value of the amplitude all over the domain of the radar scan.  相似文献   

11.
机载探地雷达数值模拟及逆时偏移成像   总被引:4,自引:4,他引:0       下载免费PDF全文
机载探地雷达可以用于人类无法到达的危险地区、植被严重覆盖的地下目标体探测,然而由于机载探地雷达的特殊性,影响机载探地雷达探测效果的因素包括天线的极化方向、天线的飞行高度以及地表粗糙度等.为了研究这些影响因素与探测效果之间的关系,用三维时间域有限差分模拟电磁波的传播过程,以沙漠地区地下空洞掩体的机载探地雷达探测为实例,分别模拟了不同天线极化方向、天线高度及地表粗糙度情况下的机载探地雷达剖面,分析了各因素对机载探地雷达探测地下空洞目标体的影响.天线极化方向与目标体走向垂直更有利于地下目标体探测;天线距离地表越近,可以获得更高分辨率的雷达剖面;沙漠地表起伏越大,雷达剖面中的散射杂波能量越强,浅部地下目标体信号容易被掩盖.为了消除起伏地形造成的散射杂波,提出用逆时偏移成像技术对共炮集机载探地雷达数据进行偏移成像,成像结果优于基尔霍夫偏移成像结果.  相似文献   

12.
Shallow carbonates are of utmost importance as potential sources of groundwater in karstified semi-arid terrains. Ground-Penetrating Radar (GPR) is being increasingly used as a prominent mapping tool in such environments. However, its potential in exploring and identifying shallow water-saturated zones (WSZs) in carbonates is constrained by the geoelectrical properties of carbonate soils as a function of moisture content. We report results of a case study that includes laboratory geoelectrical characterization and their comparison to in situ GPR attenuation measurements performed on Cretaceous Edwards Formation rudist mounds in central Texas, which we hypothesize as analogs for water-bearing formations in semi-arid karstified carbonate terrains. Dielectric measurements on field-collected rock samples carried out in the laboratory under controlled conditions of moisture saturation suggest that real and imaginary parts of dielectric constants of rocks with higher porosity and/or permeability have steeper dependence on pore moisture content; they produce better dielectric contrasts but allow shallower penetration. Our analyses suggest that within carbonates, dielectric contrasts improve with decrease in sounding frequency and/or increase in moisture content; and the relationship between dielectric permittivity and moisture content may be represented by 3rd order polynomial equations. GPR surveys using a wide-band 400 MHz antenna reveal subsurface mound morphologies with heights of ~ 1–2 m and basal diameters of ~ 8–10 m resembling outcrop analogs. Each mound appears to be composed of smaller amalgamated lithounits that seem geoelectrically similar. Amplitudes decays of the backscattered radar signal correlate to moisture distribution. Measuring the differences in signal attenuation allows differentiation between saturated and non-saturated zones. Velocity analyses of GPR profiles enable estimation of moisture distribution in the vicinity of the mounds. Optimal delineation and production of high-resolution GPR data up to a depth of ~ 10 m were observed for a sounding frequency of ~ 250 MHz with moisture content of ~ 5% by weight. Below this moisture level, the dielectric contrast is insufficient to uniquely identify water-saturated zones from the surrounding geoelectrical context, and above it, the radar signal is substantially attenuated leading to a total inefficiency of the method.  相似文献   

13.
The structure and ice content of ice caves are poorly understood. Ground penetrating radar (GPR) can provide useful insights but has only rarely been applied to ice caves. This paper interprets GPR images (radargrams) in terms of internal structure, stratification, compaction, thickness and volume of the ice block in the Peña Castil ice cave (Central Massif of Picos de Europa, northern Spain), providing the endokarst geometry of the ice cave in GPR data reflections. Eight radargrams were obtained by applying a shielded ground‐coupled antenna with a nominal frequency of 400 MHz. Although the radargrams do not depict the ice–basal bedrock interface, they suggest that the ice block is at least 54 m deep and similarly thick. Some curved reflection signatures suggest a potential vertical displacement in the block of ice, and thus certain dynamics in the ice body. Other images show numerous interbedded clasts and thin sediment layers imaged as banded reflections. In this particular cave a direct visual inspection of the ice stratigraphy is a difficult task but GPR provides clear reflectivity patterns of some of its internal features, making GPR a suitable instrument for this and future studies to achieve a better and broader understanding of the internal behavior of ice caves.  相似文献   

14.
Dipole antennas for ground-penetrating radar (GPR) radiate and receive electromagnetic waves with a strong directional dependence. Thus, experiments to measure in situ antenna radiation as functions of direction and polarization are of practical interest. Three field experiments were performed. One experiment was over a layered fluvial/eolian sequence; the other two used controlled targets (buried pipes and a metal ball). The radiation patterns were sampled by incrementally varying the antenna orientations and separations while recording reflections from the known targets. The results show qualitative, but systematic, correspondence with approximate theoretical far-field radiation patterns. Slow variations of amplitude with antenna azimuth and dip indicate that antenna orientations within 20° in the standard TE and TM acquisition geometries are adequate for most field applications, but not if detailed amplitude analysis is to be performed. Variations in antenna orientation or height (particularly for heights less than one-quarter wavelength) above the free surface introduce corresponding biases or uncertainties into recorded amplitudes. The variance within any suite of measurements is, in part, a consequence of differences in ground impedance at each antenna location. The theoretically predicted sensitivity to antenna height is mediated by surface roughness at high frequencies. It is necessary to include, or compensate for, the antenna radiation pattern in analysis of field data amplitudes, in experiment design, and in selecting appropriate antennas for specific applications.  相似文献   

15.
A plant is stabilized by its root system. In congested urban cities such as Hong Kong, ground trenching is frequently seen due to the installation of utility lines along the roadside. Soil nailing, which involves soil coring in slopes, is a common solution to improve the slope stability. However, both activities inevitably pose a risk to the integrity of any root systems present, and thus reduce the root anchorage. To prevent or minimize such damage, a careful design of the excavation/drilling location is of prime importance. Ground penetrating radar (GPR) provides a non-destructive method for locating roots by examining the contrast between the dielectric properties of the roots and the surrounding soil. To examine the performance of GPR and promote its use in Hong Kong, a test bed was prepared using local materials to create a controlled environment in which to conduct a series of systematic tests evaluating the performance of a 900 MHz GPR. The reflected radargrams were subject to the influence of the following factors: size and depth of roots, horizontal distance between roots, and contrast between the root and soil water content. Correlations between root size and a number of waveform parameters were also explored. Limiting values for root size, root embedded depth, horizontal separation distance between roots, and water content contrast between root and soil were obtained. A significant correlation was found between the root diameter and time travel parameter T 2 (p<0.001, r=0.795). Because GPR root detection is highly site-specific, this study provides a local reference for GPR performance in the Hong Kong environment. The findings demonstrate that the 900 MHz GPR is applicable in Hong Kong for the detection of main roots.  相似文献   

16.
The amplitude spectrum of ground penetrating radar (GPR) reflection data acquired with a particular antenna set is normally concentrated over a spectral bandwidth of a single octave, limiting the resolving power of the GPR wavelet. Where variously-sized GPR targets are located at numerous depths in the ground, it is often necessary to acquire several profiles of GPR data using antennas of different nominal frequencies. The most complete understanding of the subsurface is obtained when those frequency-limited radargrams are jointly interpreted, since each frequency yields a particular response to subsurface reflectivity. The application of deconvolution to GPR data could improve image quality, but is often hindered by limited spectral bandwidth.We present multiple-frequency compositing as a means of combining data from several frequency-limited datasets and improving the spectral bandwidth of the GPR profile. A multiple-frequency composite is built by summing together a number of spatially-coincident radargrams, each acquired with antennae of different centre frequency. The goal of the compositing process is therefore to produce a composite radargram with balanced contributions from frequency-limited radargrams and obtain a composite wavelet that has properties approximating a delta function (i.e. short in duration and having a broad, uniform spectral bandwidth).A synthetic investigation of the compositing process was performed using Berlage wavelets as proxies for GPR source pulses. This investigation suggests that a balanced, broad bandwidth, effective source pulse is obtained by a compositing process that equalises the spectral maxima of frequency-limited wavelets prior to summation into the composite. The compositing of real GPR data was examined using a set of 225, 450 and 900 MHz GPR common offset profiles acquired at a site on the Waterloo Moraine in Ontario, Canada. The most successful compositing strategy involved derivation of scaling factors from a time-variant least squares analysis of the amplitude spectra of each frequency-limited dataset. Contributions to the composite from each nominal acquisition frequency are clear, and the trace averaged amplitude spectrum of the corresponding composite is broadened uniformly over a bandwidth approaching two-octaves. Improvements to wavelet resolution are clear when a composite radargram is treated with a spiking deconvolution algorithm. Such improvement suggests that multiple-frequency compositing is a useful imaging tool, and a promising foundation for improving deconvolution of GPR data.  相似文献   

17.
全极化探地雷达正演模拟   总被引:4,自引:1,他引:3       下载免费PDF全文
全极化探地雷达不但能获取当前探地雷达使用的共极化信息,而且能使用交叉极化信息,进而更好地分析目标属性.本文在时域有限差分法的基础上,构建了全极化探地雷达的正演模拟方法,通过水平正交双方向同时接收获取全极化信息.标准目标体金属板和角反射器的正演模拟与实验室物理模型测试一致的共极化和交叉极化响应信息,证实了该正演模拟方法的...  相似文献   

18.
以SIR-3000单通道地质雷达的400MHz,900MHz天线为研究手段,说明地质雷达在探测同一目的区的应用效果。  相似文献   

19.
Twelve ground penetrating radar (GPR) experiments were conducted on the modern, wave-influenced William River delta, on the Southern shore of Lake Athabasca in northern Saskatchewan, Canada. The delta is a well-sorted, quartzoserich, clean, sand-dominated, water-saturated geomorphic feature which provided an ideal site to test GPR. Penetration depths, resolution and continuity of reflections were compared for different antennae frequencies (25, 50, 100, 200 MHz) and transmitter powers (pulser voltage: 400 V, 1000 V). The data show significant variations in vertical resolution from 0.15 m to 0.76 m (200-25 MHz), depth of penetration from 14 m-28 m (200-25 MHz), and continuity of reflections. Increasing the transmitter power from 400 V to 1000 V increases the depth of penetration by 5 to 14% and improves the continuity of reflections with little effect on the resolution.  相似文献   

20.
Reduction of reflections from above surface objects in GPR data   总被引:2,自引:0,他引:2  
During a ground-penetrating radar (GPR) survey, special attention must be paid to objects located above the earth's surface. Due to the low-loss character of electromagnetic propagation in air and high velocity, above-surface reflections or diffractions can overwhelm subsurface events, making the interpretation a difficult task. The relative sensitivity of reflections and diffractions originating from above-surface objects is a function of the antenna radiation characteristics, the lateral and vertical dimensions of the objects and their position with respect to the antennas. The largest amplitude reflections and diffractions are expected when the polarization of the electric field is parallel to the long-axis of the object. Near the surface in the E-plane, the electric field is vertically polarized and has a larger amplitude than the horizontally polarized electric field in the H-plane. Numerical modeling of reflections from three above surface objects (a vertical plane and elongated horizontal and vertical objects) demonstrate that the largest amplitude difference occurs when an elongated vertical object is present in the E- or H-plane. The calculated reflection from the elongated vertical object present in the E-plane was 21 times larger than when it was present in the H-plane. In 60-m long field data sets, reflections from interfering trees present in the E-plane were at several positions >15 times larger and on average 6 times larger than when the trees were present in the H-plane. These large amplitude differences indicate that appropriate orientation of the antennas can be used to minimize the effects of above-surface reflections and diffractions.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号