共查询到19条相似文献，搜索用时 734 毫秒
1.
基于CLoE与Gudehus-Bauer亚塑性模型数值模拟了平面应变条件下Hostun砂的应变局部化现象。从侧向压力和初始缺陷两个方面对比研究了两种模型所预测应变局部化的产生及演化模式。结果表明：（1）两种模型均能反映Hostun砂刚度随着侧向压力提高而增大的现象。（2）相比Gudehus-Bauer亚塑性模型,CLoE亚塑性模型所得出的应变局部化形态与试验结果更加一致。（3）CLoE亚塑性模型能够反映随着荷载增加,砂的体积先膨胀后缩小的特点。（4）相比Gudehus-Bauer亚塑性模型,CLoE亚塑性模型所得到的应变-应力曲线能够更明显地反映应变局部化带中单元的软化现象。（5）CLoE亚塑性模型能够更好地模拟由初始缺陷导致的不均匀应变。总的来说,所得的数值结果表明,CLoE亚塑性模型能够较好地模拟侧向压力和初始缺陷对应变局部化的影响,在模拟应变局部化现象方面较Gudehus-Bauer更有优势。然而,现有CLoE亚塑性模型无法考虑孔隙比,也未包含颗粒材料内尺度变量,有待进一步完善。 相似文献
2.
3.
4.
高速铁路路基上的轨道以及附近区域的结构物承受低幅值、高循环振动荷载的反复作用。在此低幅值、高循环荷载作用下土体会产生不可恢复的应变累积,导致轨道及附近区域结构物发生附加沉降。当前,描述土体的循环变形特征的理论分为两类：一类是基于经典塑性理论的应力-应变滞回模型（例如边界面模型）,另一类是基于循环三轴试验经验规律的应变累积模型（例如Bochum累积模型）。为了能够预测土体在低幅值、高循环荷载作用下的应变累积行为,在前人对土体在低幅值、高循环荷载作用下大量试验研究的基础上,在经典弹塑性理论的框架下,提出一个土体在低幅值、高循环荷载作用下的应变累积模型。该模型通过用对数律来描述塑性体应变的累积规律,并以此作为应变累积的大小度量,然后通过修正Cam-clay模型的流动准则来描述应变累积的发展方向。最后,通过多组试验结果的模拟,表明所提出的应变累积模型能够较好地预测土体在低幅值、高循环荷载作用下的应变累积行为,具有广泛的应用前景。 相似文献
5.
紫坪铺面板坝堆石料颗粒破碎试验研究 总被引：2，自引：0，他引：2
采用大型三轴仪对紫坪铺面板坝堆石料进行了单调和循环荷载下的固结排水剪切试验,研究了不同孔隙比情况下颗粒破碎及剪胀的变化规律。试验表明：（1）单调和循环荷载条件下,堆石料颗粒破碎率与塑性功之间存在一致的双曲线关系;（2）峰值应力处剪胀率与颗粒破碎率在半对数坐标中呈近似线性关系;（3）峰值应力处主应力比与相应的剪胀率呈近似线性关系,且上述结果受初始孔隙比的影响不大。研究成果有助于进一步了解堆石料的颗粒破碎特点,对建立复杂应力条件下考虑颗粒破碎和状态相关性的弹塑性本构模型,分析紫坪铺面板堆石坝汶川地震破损机制是十分有益的。 相似文献
6.
为合理反映颗粒破碎对堆石料力学特性的影响,基于试验结果分析,得出了堆石料在压缩和剪切作用下的颗粒破碎特性规律。通过引入压缩破碎和剪切破碎的相关参数,借鉴已有本构模型的合理定义,吸收临界状态理论和边界面理论的优点,发展了考虑颗粒破碎和状态相关的堆石料静动力统一弹塑性本构模型,并阐述了模型参数的确定方法。该模型不仅能够反映堆石料在静力荷载作用下的低压剪胀、高压剪缩、应变软化和硬化等特性,还能够反映在循环荷载作用下应力-应变的滞回特性和残余变形的累积效应。最后为验证模型的合理性,分别对堆石料的静力三轴和循环三轴试验进行了数值模拟预测,结果表明：模型预测与试验数据吻合良好,所提出的本构模型能够合理地描述颗粒破碎对堆石料静动力变形特性的影响。 相似文献
7.
非饱和黏土的结构性能够显著影响其力学特性。基于非饱和土经典模型BBM（Barcelona basic model）和一种可描述循环塑性的硬化法则,引入体积破损率的作为标准土体结构破损的参数,建立了一个描述常吸力下非饱和结构性黏土静态及动态力学特性的弹塑性双面模型。模型在应力空间中包含与重塑非饱和土屈服面几何相似的结构性边界面和加载面,采用径向映射法则和可移动的记忆中心原理,通过结构性边界面和加载面在应力空间中的演化来反映循环加载过程中非饱和结构性黏土的循环塑性特征和结构损伤过程。通过与相关非饱和黏土控制吸力试验数据的比较,表明该模型能够较好地反映静态加载下非饱和结构性黏土的力学特性,而模型预测的循环荷载下的应力?应变特征也具有一定的合理性。 相似文献
8.
9.
本研究旨在对黏土中的桶式基础进行从完整的有限元分析到简化的宏单元的建模。首先通过有限元方法分析了在不同单调组合荷载作用下的黏土中吸力桶基础。为保证模拟结果的可靠性,采用了硬化土模型（HS）对正常固结黏土地基进行模拟。通过对比离心试验验证了使用HS模型的有限元分析的有效性,并通过径向位移试验进一步延伸到V-H-M（竖向力-水平力-弯矩）空间的破坏模式研究,并在此基础上,提出了的V-H-M空间三维破坏包络面公式。接着,应用此三维破坏包络面公式,采用亚塑性框架提出了黏土中桶式基础的宏单元设计模型。通过与试验结果的比较,验证了宏单元模型在模拟单调和循环荷载条件下桶式基础的强度与变形响应的有效性。所提的宏单元模型对于海洋岩土工程设计实践将很有帮助。 相似文献
10.
基于临界状态土力学框架,建立了一个适用于往返循环荷载作用的砂土边界面本构模型。采用无纯弹性域假设,认为受到反向荷载的瞬时土体就产生塑性变形,砂土的弹性区域退化为一个点。屈服面为倒子弹头型,由于砂土孔隙比与压力之间不存在惟一对应的关系,使得屈服面大小无法与体积应变直接耦合,故采用塑性偏应变而不是剑桥模型那种塑性体应变作为硬化参数。流动法则采用加入状态参数的修正的Rowe应力剪胀关系,体现了依赖状态的剪胀思想。屈服面大小的比值 反映了塑性模量的演化,并推导了 的表达式。只用1套参数,该模型就能合理地模拟砂土在不同密度和固结压力下循环荷载的应力-应变关系曲线。 相似文献
11.
David Ma&#x;ín Claudio Tamagnini Gioacchino Viggiani Daniele Costanzo 《国际地质力学数值与分析法杂志》2006,30(13):1303-1336
In this paper, the performance of different advanced constitutive models for soils is evaluated with respect to the experimentally observed behaviour of a soft reconstituted clay subject to a wide range of loading directions, see (presented in the companion paper). The models considered include a three‐surface kinematic hardening elastoplastic model; the CLoE hypoplastic model; a recently proposed K‐hypoplastic model for clays, and an enhanced version of the same model incorporating the concept of intergranular strain. A clear qualitative picture of the relative performance of the different models as a function of the loading direction is obtained by means of the incremental strain response envelopes. The definition of suitable error measures allows to obtain further quantitative information in this respect. For the particular initial conditions and loading programme considered in this study, the kinematic hardening and the enhanced K‐hypoplastic models appear to provide the best performance overall. Copyright © 2006 John Wiley & Sons, Ltd. 相似文献
12.
A sample of soil is subjected to multidimensional cyclic loading when two or three principal components of the stress or strain tensor are simultaneously controlled to perform a repetitive path. These paths are very useful to evaluate the performance of models simulating cyclic loading. In this article, an extension of an existing constitutive model is proposed to capture the behavior of the soil under this type of loading. The reference model is based on the intergranular strain anisotropy concept and therefore incorporates an elastic locus in terms of a strain amplitude. In order to evaluate the model performance, a modified triaxial apparatus able to perform multidimensional cyclic loading has been used to conduct some experiments with a fine sand. Simulations of the extended model with multidimensional loading paths are carefully analyzed. Considering that many cycles are simulated (\(N>30\)), some additional simulations have been performed to quantify and analyze the artificial accumulation generated by the (hypo-)elastic component of the model. At the end, a simple boundary value problem with a cyclic loading as boundary condition is simulated to analyze the model response. 相似文献
13.
This paper is devoted to a parametric study of a plane Mohr–Coulomb CLoE model. As CLoE models are designed with a consistency condition, it is possible to define a normality condition and to study its consequences. The positiveness of the second order work which implies the uniqueness of the solution of a small strain boundary value problem is studied firstly. Then the localization criterion is also studied. It is proved that normality has consequences similar to those for classical elasto plastic models. However if induced anisotropy is introduced in the hypoplastic CLoE model, some conclusions are no longer true. Finally plane strain experimental data are used to identify the parameters of the model. Copyright © 2002 John Wiley & Sons, Ltd. 相似文献
14.
For numerical studies of geotechnical structures under earthquake loading, aiming to examine a possible failure due to liquefaction, using a sophisticated constitutive model for the soil is indispensable. Such model must adequately describe the material response to a cyclic loading under constant volume (undrained) conditions, amongst others the relaxation of effective stress (pore pressure accumulation) or the effective stress loops repeatedly passed through after a sufficiently large number of cycles (cyclic mobility, stress attractors). The soil behaviour under undrained cyclic loading is manifold, depending on the initial conditions (e.g. density, fabric, effective mean pressure, stress ratio) and the load characteristics (e.g. amplitude of the cycles, application of stress or strain cycles). In order to develop, calibrate and verify a constitutive model with focus to undrained cyclic loading, the data from high-quality laboratory tests comprising a variety of initial conditions and load characteristics are necessary. It is the purpose of these two companion papers to provide such database collected for a fine sand. Part II concentrates on the undrained triaxial tests with strain cycles, where a large range of strain amplitudes has been studied. Furthermore, oedometric and isotropic compression tests as well as drained triaxial tests with un- and reloading cycles are discussed. A combined monotonic and cyclic loading has been also studied in undrained triaxial tests. All test data presented herein will be available from the homepage of the first author. As an example of the examination of an existing constitutive model, the experimental data are compared to element test simulations using hypoplasticity with intergranular strain. 相似文献
15.
The present paper introduces a comprehensive model that is capable of describing the behaviour, under cyclic loading, of the granular materials used in railway tracks and road pavement. Its main thrust is the introduction of the “Chicago” law in a continuum approach to account for the ratcheting effects. It also emphasizes rate-dependency as a dissipative mechanism that acts independently or jointly with the ratcheting effect as well as the non-associated plasticity. The numerical procedure is based on the return mapping algorithm, where Newton’s method is used to calculate the nonlinear consistency parameter of the flow rule and to obtain a consistent tangent modulus. The model was applied to specific numerical examples including multi-axial and cyclic loading conditions. 相似文献
16.
As is well known, granular soils under cyclic loading dissipate a large amount of energy and accumulate large irreversible strains. Usually, with time, this second effect reduces and the accumulation rate decreases with the number of cycles until obtaining a sort of ideal stationary cyclic state at which ratcheting disappears. In this paper, only this ideal state is taken into consideration and simulated by means of a multi‐mechanism constitutive model for plastic adaptation. For this purpose, the concept of cycle is discussed, many different categories of cyclic stress/strain paths are considered and some theoretical issues concerning both the flow and the strain‐hardening rules are tackled. Even though the paper focuses on soil behaviour, the conclusions can be extended to all materials exhibiting ratcheting due to volumetric behaviour.Copyright © 2013 John Wiley & Sons, Ltd. 相似文献
17.
This paper presents a constitutive model for describing the stress-strain response of sands under cyclic loading. The model, formulated using the critical state theory within the bounding surface plasticity framework, is an upgraded version of an existing model developed for monotonic behaviour of cohesionless sands. With modification of the hardening law, plastic volumetric strain increment and unloading plastic modulus, the original model was modified to simulate cyclic loading. The proposed model was validated against triaxial cyclic loading tests for Fuji River sand, Toyoura sand and Nigata sand. Comparison between the measured and predicted results suggests that the proposed modified model can capture the main features of cohesionless sands under drained and undrained cyclic loading. 相似文献
18.
ISA model: A constitutive model for soils with yield surface in the intergranular strain space 
下载免费PDF全文
下载免费PDF全文 In this article, a new constitutive model for soils is proposed. It is formulated by means of plasticity, but in contrast to the precedent works, it presents a yield function describing a surface within the intergranular strain space. This latter is a state variable providing information of the recent strain history. An expression for the plastic strain rate has been proposed to guarantee the stress rate continuity. Under the application of medium or large strain amplitudes, the constitutive equation becomes independent of the intergranular strain and delivers a mathematical structure similar to some Karlsruhe hypoplastic models. Some simulations of monotonic and cyclic triaxial test are provided to evaluate and analyze the model performance. Copyright © 2015 John Wiley & Sons, Ltd. 相似文献
19.
A modification to the nonlinear Pastor–Zienkiewicz–Chan (PZC) constitutive model without any change in the number of model parameters is introduced in order to simulate stiffness degradation of dense sands at dynamic loading. The PZC model is based on generalized plasticity and was verified by good prediction of liquefaction and undrained behavior of saturated sand. The PZC is a robust model that can predict drained dynamic behavior of sands, especially stiffness increase in loose sand at reloading of dynamic loading. Yet, this model does not show stiffness degradation of dense sand at reloading. The modification is made through modifying the stress memory factor, H DM, which is multiplied by the plastic modulus, H L. This modification does not influence reloading behavior of loose sand. The modified PZC model is verified via results of drained cyclic tests. Two cyclic triaxial tests on loose and dense specimens, along with two cyclic plane strain tests on dense sand are utilized for validation. The model simulation shows that the modified PZC model is able to predict the stiffness degradation of dense sand at reloading well. 相似文献