共查询到20条相似文献，搜索用时 46 毫秒
1.
With oblique rifting, both extension perpendicular to the rift trend and shear parallel to the rift trend contribute to rift formation. The relative amounts of extension and shear depend on α, the acute angle between the rift trend and the relative displacement direction between opposite sides of the rift. Analytical and experimental (clay) models of combined extension and left-lateral shear suggest the fault patterns produced by oblique rifting. If α is less than 30°, conjugate sets of steeply dipping strike-slip faults form in rifts. Sinistral and dextral strike-slip faults trend subparallel and at large angles to the rift trend, respectively. If α is about 30°, strike-slip, oblique-slip and/or normal faults form in rifts. Faults with sinistral and dextral strike slip trend subparallel and at large angles to the rift trend, respectively. Normal faults strike about 30° counterclockwise from the rift trend. If α exceeds 30°, normal faults form in rifts. They have moderate dips and generally strike obliquely to the rift trend and to the relative displacement direction between opposite sides of the rift. If α equals 90°, the normal faults strike parallel to the rift trend and perpendicularly to the displacement direction.The modeling results apply to the Gulf of California and Gulf of Aden, two Tertiary continental rift systems produced by combined extension and shear. Our results explain the presence and trends of oblique-slip and strike-slip faults along the margins of the Gulf of California and the oblique trend (relative to the rift trend) of many normal faults along the margins of both the Gulf of California and the Gulf of Aden. 相似文献
2.
A. A. Peyve 《Geotectonics》2009,43(2):87-99
The accretion of oceanic crust under conditions of oblique spreading is considered. It is shown that deviation of the normal to the strike of mid-ocean ridge from the extension direction results in the formation of echeloned basins and ranges in the rift valley, which are separated by normal and strike-slip faults oriented at an angle to the axis of the mid-ocean ridge. The orientation of spreading ranges is determined by initial breakup and divergence of plates, whereas the within-rift structural elements are local and shallow-seated; they are formed only in the tectonically mobile rift zone. As a rule, the mid-ocean ridges with oblique spreading are not displaced along transform fracture zones, and stresses are relaxed in accommodation zones without rupture of continuity of within-rift structural elements. The structural elements related to oblique spreading can be formed in both rift and megafault zones. At the initial breakup and divergence of continental or oceanic plates with increased crust thickness, the appearance of an extension component along with shear in megafault zones gives rise to the formation of embryonic accretionary structural elements. As opening and extension increase, oblique spreading zones are formed. Various destructive and accretionary structural elements (nearly parallel extension troughs; basin and range systems oriented obliquely relative to the strike of the fault zone and the extension axis; rhomb-shaped extension basins, etc.) can coexist in different segments of the fault zone and replace one another over time. The Andrew Bain Megafault Zone in the South Atlantic started to develop as a strike-slip fault zone that separated the African and Antarctic plates. Under extension in the oceanic domain, this zone was transformed into a system of strike-slip faults divided by accretionary structures. It is suggested that the De Geer Megafault Zone in the North Atlantic, which separated Greenland and Eurasia at the initial stage of extension that followed strike-slip offset, evolved in the same way. 相似文献
3.
Metamorphic core complexes are usually thought to be associated with regional crustal extension and crustal thinning, where deep crustal material is exhumed along gently dipping normal shear zones oblique to the regional extension direction. We present a new mechanism whereby metamorphic core complexes can be exhumed along crustal‐scale strike‐slip fault systems that accommodated crustal shortening. The Qazaz metamorphic dome in Saudi Arabia was exhumed along a gently dipping jog in a crustal‐scale vertical strike‐slip fault zone that caused more than 25 km of exhumation of lower crustal rocks by 30 km of lateral motion. Subsequently, the complex was transected by a branch of the strike‐slip fault zone, and the segments were separated by another 30 km of lateral motion. Strike‐slip core complexes like the Qazaz Dome may be common and may have an important local effect on crustal strength. 相似文献
4.
《Russian Geology and Geophysics》2007,48(7):598-609
New structural and tectonophysical data, combined with the published geophysical and seismological evidence, were used to map the Late Cenozoic fault pattern and crustal stress in the Barguzin rift. Faults striking in the NE direction are the most abundant elements of the rift structure. A special part in the Late Cenozoic patterns of faults and stresses belongs to an over 400 km long N-S lineament which shows up as a system of separate fault segments between 110° and 110°30′ E. The Late Cenozoic evolution of the rift has been controlled mainly by extension punctuated with local shear stresses derived from the regional extension stress and accommodated by strike slip, combined with the dominant normal motion, along NE or N-NE faults and/or along their cross faults. Extension was of a relatively stable NW-SE direction, almost rift-orthogonal. The obtained fault pattern and stress maps can be used for reference in mapping seismic hazard associated with ongoing faulting in an active and changeable stress field. 相似文献
5.
6.
In this paper we assess two competing tectonic models for the development of the Isa Superbasin (ca 1725–1590 Ma) in the Western Fold Belt of the Mt Isa terrane. In the ‘episodic rift‐sag’ tectonic model the basin architecture is envisaged as similar to that of a Basin and Range province characterised by widespread half‐graben development. According to this model, the Isa Superbasin evolved during three stages of the Mt Isa Rift Event. Stage I involved intracontinental extension, half‐graben development, the emergence of fault scarps and tilt‐blocks, and bimodal volcanism. Stage II involved episodic rifting and sag during intervening periods of tectonic quiescence. Stage III was dominated by thermal relaxation of the lithosphere with transient episodes of extension. Sedimentation was controlled by the development of arrays of half‐grabens bounded by intrabasinal transverse or transfer faults. The competing ‘strike‐slip’ model was developed for the Gun Supersequence stratigraphic interval of the Isa Superbasin (during stage II and the beginning of stage III). According to this model, sinistral movements along north‐northeast‐orientated strike‐slip faults took place, with oblique movements along northwest‐orientated faults. This resulted in the deposition of southeast‐thickening ramp sequences with local sub‐basin depocentres forming to the west and north of north‐northeast‐ and northwest‐trending faults, respectively. It is proposed that dilation zones focused magmatism (e.g. Sybella Granite) and transfer of strike‐slip movement resulted in transient uplift along the western margin of the Mt Gordon Arch. Our analysis supports the ‘episodic rift‐sag’ model. We find that the inferred architecture for the strike‐slip model correlates poorly with the observed structural elements. Interpretation is made difficult because there has been significant modification and reorientation of fault geometry during the Isan Orogeny and these effects need to be removed before any assertion as to the basin structure is made. Strike‐slip faulting does not explain the regional‐scale pattern of basin subsidence. The ‘episodic rift‐sag’ model explains the macroscopic geometry of the Isa Superbasin and is consistent with the detailed sedimentological analysis of basin facies architecture, and the structural history and geometry. 相似文献
7.
曲折边界斜向裂陷伸展的砂箱实验模拟 总被引：3，自引：0，他引：3
根据黄骅盆地边界几何特征简化所设计的３个砂箱实验模型表明,同一裂陷伸过程可以形成不同走向的正断层,基底菜边界方向的变化可以引起裂陷内部断层走向的变化,陷盆地断瞳向受基底展边界方向和裂陷伸展方向的共同影响,裂陷边界及其附近断层走向主要受基底伸展边界方向的影响,裂陷内部、离伸展边界较远部位的断层走向主要受展方向影响,凸菜曲折边界可以引起断层转向,而凹工折边界的复合方向构成对断层走向的控制,黄骅新生代盆 相似文献
8.
Close relationships between deformation and volcanism are well documented in relatively late evolutionary stages of continental rifting, whereas these are poorly constrained in less mature rifting stages. To investigate the control of inherited structures on faulting and volcanism, we present a statistical analysis of volcanic features, faults and pre‐rift fabric in the Tanzania Divergence, where volcanic features occur extensively in in‐rift and off‐rift areas. Our results show that in mature rift sectors (Natron), magma uprising is mostly controlled by fractures/faults responding to the far‐field stress, whereas the distribution of volcanism during initial rifting (Eyasi) is controlled by inherited structures oblique to the regional extension direction. Off‐rift sectors show a marked control of pre‐rift structures on magma emplacement, which may not respond to the regional stress field. Thus, the use of off‐rift magmatic features as stress indicators should take into account the role of pre‐existing structures. 相似文献
9.
Large earthquakes in strike-slip regimes commonly rupture fault segments that are oblique to each other in both strike and dip. This was the case during the 1999 Izmit earthquake, which mainly ruptured E–W-striking right-lateral faults but also ruptured the N60°E-striking Karadere fault at the eastern end of the main rupture. It will also likely be so for any future large fault rupture in the adjacent Sea of Marmara. Our aim here is to characterize the effects of regional stress direction, stress triggering due to rupture, and mechanical slip interaction on the composite rupture process. We examine the failure tendency and slip mechanism on secondary faults that are oblique in strike and dip to a vertical strike-slip fault or “master” fault. For a regional stress field well-oriented for slip on a vertical right-lateral strike-slip fault, we determine that oblique normal faulting is most favored on dipping faults with two different strikes, both of which are oriented clockwise from the strike-slip fault. The orientation closer in strike to the master fault is predicted to slip with right-lateral oblique normal slip, the other one with left-lateral oblique normal slip. The most favored secondary fault orientations depend on the effective coefficient of friction on the faults and the ratio of the vertical stress to the maximum horizontal stress. If the regional stress instead causes left-lateral slip on the vertical master fault, the most favored secondary faults would be oriented counterclockwise from the master fault. For secondary faults striking ±30° oblique to the master fault, right-lateral slip on the master fault brings both these secondary fault orientations closer to the Coulomb condition for shear failure with oblique right-lateral slip. For a secondary fault striking 30° counterclockwise, the predicted stress change and the component of reverse slip both increase for shallower-angle dips of the secondary fault. For a secondary fault striking 30° clockwise, the predicted stress change decreases but the predicted component of normal slip increases for shallower-angle dips of the secondary fault. When both the vertical master fault and the dipping secondary fault are allowed to slip, mechanical interaction produces sharp gradients or discontinuities in slip across their intersection lines. This can effectively constrain rupture to limited portions of larger faults, depending on the locations of fault intersections. Across the fault intersection line, predicted rakes can vary by >40° and the sense of lateral slip can reverse. Application of these results provides a potential explanation for why only a limited portion of the Karadere fault ruptured during the Izmit earthquake. Our results also suggest that the geometries of fault intersection within the Sea of Marmara favor composite rupture of multiple oblique fault segments. 相似文献
10.
P. J. Lyon P. J. Boult R. R. Hillis K. Bierbrauer 《Australian Journal of Earth Sciences》2013,60(5):675-689
The Penola Trough is an intensely faulted northwest – southeast-trending half-graben structure. It is bound to the south by the major listric Hungerford/Kalangadoo Fault system. Several large prominent faults observed in the Penola Trough show offset of basement at depth. These basement-rooted faults have exerted significant controls on the geometry of smaller intra-rift faults throughout the entire structural history of the area. Faulting of the basement was initiated during the initial rift event of the Late Jurassic – Early Cretaceous. Faulting first propagated through a pre-existing basement fabric oblique to the north – south extension direction prevalent during this time. This resulted in the formation of the Hungerford/Kalangadoo and St George Faults with a northwest – southeast and north-northeast – south-southwest trend, respectively. A series of east – west-trending basement faults subsequently initiated perpendicular to the north – south extension direction as extensional strain increased in magnitude. Significant displacement along these basement-rooted faults throughout the initial rift event was associated with the formation of a complex set of intra-rift faults. These intra-rift faults exhibit a broadly east – west orientation consistent with the interpreted north – south extensional direction. However, this east – west orientation locally deviates to a more northwest – southeast direction near the oblique-trending St George Fault, attributed to stress perturbation effects. Many of the intra-rift faults die out prior to the end of the Early Cretaceous initial rift event while displacement on basement faults continued throughout. Faulting activity during the Late Cretaceous post-rift fault event was almost exclusively localised onto basement faults, despite a significant change in extension direction to northeast – southwest. A high-density, en échelon array of northwest – southeast-trending fault segments formed directly above the St George Fault and the large east – west-trending basement faults contemporaneously reactivated. Seismic variance data show that post-rift fault segments that are hard-linked to the St George Fault at depth have propagated through near-surface units. Non-basement-linked post-rift fault segments that lie away from the St George basement have not. This suggests that recent fault activity has continued to occur preferentially along basement faults up to relatively recent times, which has significant implications for fault seal integrity in the area. This is empirically validated by our structural analysis of fault-dependent hydrocarbon traps in the area, which shows that partially breached or breached hydrocarbon columns are associated with basement faults, whereas unbreached hydrocarbon columns are not. 相似文献
11.
《Geodinamica Acta》2001,14(1-3):197-212
The Karasu Rift (Antakya province, SE Turkey) has developed between east-dipping, NNE-striking faults of the Karasu fault zone, which define the western margin of the rift and west-dipping, N–S to N20°–30°E-striking faults of Dead Sea Transform fault zone (DST) in the central part and eastern margin of the rift. The strand of the Karasu fault zone that bounds the basin from west forms a linkage zone between the DST and the East Anatolian fault zone (EAFZ). The greater vertical offset on the western margin faults relative to the eastern ones indicates asymmetrical evolution of the rift as implied by the higher escarpments and accumulation of extensive, thick alluvial fans on the western margins of the rift. The thickness of the Quaternary sedimentary fill is more than 465 m, with clastic sediments intercalated with basaltic lavas. The Quaternary alkali basaltic volcanism accompanied fluvial to lacustrine sedimentation between 1.57 ± 0.08 and 0.05 ± 0.03 Ma. The faults are left-lateral oblique-slip faults as indicated by left-stepping faulting patterns, slip-lineation data and left-laterally offset lava flows and stream channels along the Karasu fault zone. At Hacılar village, an offset lava flow, dated to 0.08 ± 0.06 Ma, indicates a rate of left-lateral oblique slip of approximately 4.1 mm·year–1. Overall, the Karasu Rift is an asymmetrical transtensional basin, which has developed between seismically active splays of the left-lateral DST and the left-lateral oblique-slip Karasu fault zone during the neotectonic period. 相似文献
12.
Structure and evolution of an obliquely sheared continental margin: Rio Muni, West Africa 总被引：4，自引：0，他引：4
Oblique-shear margins are divergent continental terrains whose breakup and early drift evolution are characterized by significant obliquity in the plate divergence vector relative to the strike of the margin. We focus on the Rio Muni margin, equatorial West Africa, where the ca. 70-km-wide Ascension Fracture Zone (AFZ) exhibits oblique–slip faulting and synrift half-graben formation that accommodated oblique extension during the period leading up to and immediately following whole lithosphere failure and continental breakup (ca. 117 Ma). Oblique extension is recorded also by strike–slip and oblique–slip fault geometry within the AFZ, and buckling of Aptian synrift rocks in response to block rotation and local transpression. Rio Muni shares basic characteristics of both rifted and transform margins, the end members of a spectrum of continental margin kinematics. At transform margins, continental breakup and the onset of oceanic spreading (drifting) are separate episodes recorded by discrete breakup and drift unconformities. Oceanic opening will proceed immediately following breakup on a rifted margin, whereas transform and oblique-shear margins may experience several tens of millennia between breakup and drift. Noncoeval breakup and drift have important consequences for the fit of the equatorial South American and African margins because, in reconstructing the configuration of conjugate continental margins at the time of their breakup, it cannot be assumed that highly segmented margins like the South Atlantic will match each other at their ocean–continent boundaries (OCBs). Well known ‘misfits’ in reconstructions of South Atlantic continental margins may be accounted for by differential timing of breakup and drifting between oblique-shear margins and their adjacent rifted segments. 相似文献
13.
This study aims at showing how far pre-existing crustal weaknesses left behind by Proterozoic mobile belts, that pass around cratonic Archean shields (Tanzania Craton to the southeast and Congo Craton to the northwest), control the geometry of the Albertine Rift. Focus is laid on the development of the Lake Albert and Lake Edward/George sub-segments and between them the greatly uplifted Rwenzori Mountains, a horst block located within the rift and whose highest peak rises to >5000 m above mean sea level. In particular we study how the southward propagating Lake Albert sub-segment to the north interacts with the northward propagating Lake Edward/George sub-segment south of it, and how this interaction produces the structures and geometry observed in this section of the western branch of the East African Rift, especially within and around the Rwenzori horst. We simulate behaviour of the upper crust by conducting sandbox analogue experiments in which pre-cut rubber strips of varying overstep/overlap connected to a basal sheet and oriented oblique and/or orthogonal to the extension vector, are placed below the sand-pack. The points of connection present velocity discontinuities to localise deformation, while the rubber strips represent ductile domain affected by older mobile belts. From fault geometry of developing rift segments in plan view and section cuts, we study kinematics resulting from a given set of boundary conditions, and results are compared with the natural scenario. Three different basal model-configurations are used to simulate two parallel rifts that propagate towards each other and interact. Wider overstep (model SbR3) produces an oblique transfer zone with deep grabens (max. 7.0 km) in the adjoining segments. Smaller overlap (model SbR4) ends in offset rift segments without oblique transfer faults to join the two, and produces moderately deep grabens (max. 4.6 km). When overlap doubles the overstep (model SbR5), rifts propagate sub-orthogonal to the extension direction and form shallow valleys (max. 2.9 km). Relative ratios of overlap/overstep between rift segments dictate the kind of transition zone that develops and whether or not a block (like the Rwenzoris) is captured and rotates; hence determining the end-member geometry. Rotation direction is controlled by pre-existing fabrics. Fault orientation, fault kinematics, and block rotation (once in play) reinforce each other; and depending on the local kinematics, different parts of a captured block may rotate with variable velocities but in the same general direction. Mechanical strength anisotropy of pre-structured crust only initially centres fault nucleation and propagation parallel to the grain of weakness of the basement, but at later stages of a protracted period of crustal extension, such boundaries are locally defied. 相似文献
14.
Structural studies of the Barmer Basin in Rajasthan, northwest India, demonstrate the important effect that pre-existing faults can have on the geometries of evolving fault systems at both the outcrop and basin-scale. Outcrop exposures on opposing rift margins reveal two distinct, non-coaxial extensional events. On the eastern rift margin northwest–southeast extension was accommodated on southwest- and west-striking faults that form a complex, zig-zag fault network. On the western rift margin northeast–southwest extension was accommodated on northwest-striking faults that form classical extensional geometries.Combining these outcrop studies with subsurface interpretations demonstrates that northwest–southeast extension preceded northeast–southwest extension. Structures active during the early, previously unrecognised extensional event were variably incorporated into the evolving fault systems during the second. In the study area, an inherited rift-oblique fault transferred extension from the rift margin to a mid-rift fault, rather than linking rift margin fault systems directly. The resultant rift margin accommodation structure has important implications for early sediment routing and depocentre evolution, as well as wider reaching implications for the evolution of the rift basin and West Indian Rift System. The discovery of early rifting in the Barmer Basin supports that extension along the West Indian Rift System was long-lived, multi-event, and likely resulted from far-field plate reorganisations. 相似文献
15.
渤海湾盆地是一个在早白垩世被动裂陷盆地基础上发育起来的新生代主动裂陷盆地, 走滑作用贯穿始终, 特别是在兰聊-盐山断层以东, 使这个裂陷盆地具有鲜明的走滑特征。伸展和走滑作用此消彼长, 伸展构造和走滑构造相互叠加、转换, 垂向上相互叠置、交切, 并由此导致变换带的产生。晚中生代以来太平洋板块向欧亚板块俯冲的方向和速度变化、后撤以及板片窗效应、中始新世印欧板块碰撞导致的地幔上涌是控制盆地形成的深部背景, 郯庐断裂带早白垩世强烈的左行走滑、古新世-早始新世弱的左行走滑以及中始新世后的右行走滑活动也深刻地控制和影响着盆地的发育, 盆地内晚中生代-新生代的伸展和走滑构造的演化则是其浅部响应, 并由此控制着岩浆活动以及油气生成、运聚和分布的时空迁移。 相似文献
16.
The evolution of east coast of India sis discussed within the ambit of clearly identifiable four major tectonic stages which
had a profound effect in shaping the tectonic grain of the east coast basins. The evolutionary process began with rift related
crustal extension between India and Sri Lanka as a consequence of Africa-Antarctica rifting and development of Natal Basin.
An arm of this rift led to initial extension in the Cauvery Basin and failed. Later, the India-West Australia rift propagated
further in southwesterly direction initiating Mahanadi and Krishna-Godavari Basins. This extension was an oblique one with
Nayudupeta high acting as pivot. The oblique extension followed by asymmetric seafloor spreading developed transpression along
India-Sri Lanka and Antarctica junction, resulting in a NNW-SSE trending transcurrent fault along which Antarctica moved southward.
Subsequently, entire east coast evolved through a more or less uniform post rift stage. 相似文献
17.
The interaction modalities of transfer zones connecting rift segments may be influenced by several factors. Amongst these, the location and architecture of transfer zones in narrow rifts has been repeatedly associated with the presence of inherited basement anisotropies. Sand-box models were made to investigate how the orientation, geometry and kinematics of transfer zones depend upon pre-existing basement anisotropies. Analogue models reproduced offset rift segments linked by transfer zones bordered by arcuate normal faults. Strike-slip faults are present inside the transfer zone, provided that angle α (between the extension direction and the axis of the transfer zone) is less than 50°. Narrower transfer zones, striking oblique to the extension direction, occur for angle φ (between the direction perpendicular to the extension direction and the direction of the basement anisotropy) less than 90°; wider transfer zones, subparallel to the extensional direction, occur for φ > 90°. Increasing the overstep induces narrower transfer zones striking subparallel to the extension direction. Similar geometrical and kinematical patterns have been found at transfer zones in narrow rifts. The comparison between experimental and natural data shows how the geometry, kinematics and orientation of natural transfer zones depends upon the trend of inherited anisotropies: transfer zones along inherited basement structures set at lower angles to the extension direction, and display lower aspect ratios, than transfer zones where inherited anisotropies are absent. 相似文献
18.
AbstractThe Karasu Rift (Antakya province, SE Turkey) has developed between east-dipping, NNE-striking faults of the Karasu fault zone, which define the western margin of the rift and westdipping, N-S to N20°-30°E-striking faults of Dead Sea Transform fault zone (DST) in the central part and eastern margin of the rift. The strand of the Karasu fault zone that bounds the basin from west forms a linkage zone between the DST and the East Anatolian fault zone (EAFZ). The greater vertical offset on the western margin faults relative to the eastern ones indicates asymmetrical evolution of the rift as implied by the higher escarpments and accumulation of extensive, thick alluvial fans on the western margins of the rift. The thickness of the Quaternary sedimentary fill is more than 465 m, with clastic sediments intercalated with basaltic lavas. The Quaternary alkali basaltic volcanism accompanied fluvial to lacustrine sedimentation between 1.57 ± 0.08 and 0.05 ± 0.03 Ma. The faults are left-lateral oblique-slip faults as indicated by left-stepping faulting patterns, slip-lineation data and left-laterally offset lava flows and stream channels along the Karasu fault zone. At Hacilar village, an offset lava flow, dated to 0.08 ± 0.06 Ma, indicates a rate of leftlateral oblique slip of approximately 4.1 mm?year?1. Overall, the Karasu Rift is an asymmetrical transtensional basin, which has developed between seismically active splays of the left-lateral DST and the left-lateral oblique-slip Karasu fault zone during the neotectonic period. © 2001 Éditions scientifiques et médicales Elsevier SAS 相似文献
19.
斜向逆冲作用在自然界普遍存在,研究斜向逆冲断层相关褶皱的构造几何学特征,识别断层相关褶皱是否存在斜向逆冲有重要意义。文章采用Trishear 4.5、Gocad以及Trishear3D软件构建一系列不同滑移量的断层转折褶皱和断层传播褶皱的二维正演剖面,通过连接一系列不同排列方式的二维剖面建立了三种不同逆冲滑移方向的断层转折褶皱和断层传播褶皱的假三维模型,通过不同假三维模型的比较分析来探讨斜向逆冲断层相关褶皱的构造几何学特征。研究发现,斜向逆冲断层相关褶皱区别于正向逆冲断层相关褶皱的特征主要有两点：① 正向逆冲断层相关褶皱层面等高线图上的最高点与后翼等高线中点的连线以及水平切面上的核心点与后翼中点的连线方向均与断层走向垂直,而斜向逆冲断层相关褶皱的最高点以及核心点与后翼中点的连线方向均与断层走向斜交,并且最高点与后翼等高线中点的连线方向或者核心点与后翼中点的连线方向均与逆冲滑移方向一致;② 在褶皱平行断层走向纵剖面上,正向逆冲断层相关褶皱各个层面最高点的连线是直立的,而斜向逆冲断层相关褶皱各个层面最高点的连线发生倾斜。通过这两个特征可以判别褶皱是否存在斜向逆冲以及逆冲的方向。将模型分析结果运用到四川盆地西南部三维地震勘探资料所覆盖的邛西背斜和大兴西背斜的实例中。研究结果表明,两个背斜均存在右旋斜向逆冲,逆冲方向与各自断层走向的夹角均为70°左右,邛西背斜和大兴西背斜的逆冲方向分别是NE79°和NE77°左右,这与龙门山南段晚上新世以来的主应力方向以及反演的汶川地震最大主应力方向一致。 相似文献
20.
Florencia Bechis Laura Giambiagi Víctor García Silvia Lanés Ernesto Cristallini Maisa Tunik 《Journal of Structural Geology》2010,32(7):886-899
The Atuel depocenter of the Neuquén basin originated as an Upper Triassic to Lower Jurassic rift system, later inverted during the Andean contractional deformation. In order to study the extensional architecture and the kinematic evolution of this depocenter, we collected a large amount of field and sub-surface data, consisting of slip data from outcrop-scale normal faults, thickness and facies distribution within the synrift deposits, and structural data from angular and progressive unconformities. The Atuel depocenter has a NNW trend, showing a bimodal distribution of NNW and WNW major faults (first and second order faults). On the other hand, from kinematic indicators measured on outcrop-scale faults (third and fourth order faults), we found a mean NE internal extension direction, which is oblique to the general trend of the sub-basin. Taking these particular characteristics into account, we interpreted the Atuel depocenter as an oblique rift system. We evaluated two mechanisms in order to explain the development of this transtensional system: 1) reactivation of upper-crustal NNW-oriented Paleozoic shear zones, and 2) oblique stretching of a previous NNW-oriented lithospheric weakness zone. 相似文献