共查询到20条相似文献，搜索用时 312 毫秒
2.
A three-dimensional discrete element model is used to investigate the effect of grain crushing on the tip resistance measured by cone penetration tests (CPT) in calibration chambers. To do that a discrete analogue of pumice sand, a very crushable microporous granular material, is created. The particles of the discrete model are endowed with size-dependent internal porosity and crushing resistance. A simplified Hertz–Mindlin elasto-frictional model is used for contact interaction. The model has 6 material parameters that are calibrated using one oedometer test and analogies with similar geomaterials. The calibration is validated reproducing other element tests. To fill a calibration chamber capable of containing a realistic sized CPT the discrete analogue is up-scaled by a factor of 25. CPT is then performed at two different densities and three different confinement pressures. Cone tip resistance in the crushable material is practically insensitive to initial density, as had been observed in previous physical experiments. The same CPT series is repeated but now particle crushing is disabled. The ratios of cone tip resistance between the two types of simulation are in good agreement with previous experimental comparisons of hard and crushable soils. Microscale exploration of the models indicates that crushing disrupts the buttressing effect of chamber walls on the cone. 相似文献
3.
压力作用下颗粒发生破碎是引起砂土力学特性变化的重要因素之一, 对于钙质砂这种易破碎的材料更是如此。为进一步弄清颗粒破碎对钙质砂的应力-应变强度影响, 本文对钙质砂进行三轴固结排水剪切试验得到应力-应变曲线, 并筛分得到三轴试验前后钙质砂颗分曲线。通过引入Hardin定义的颗粒相对破碎率Br, 分析了相对密度、围压与颗粒破碎的关系及颗粒破碎对钙质砂应力-应变和抗剪强度的影响。结果表明:随围压的增大颗粒破碎增量逐渐减小, 直到破碎达到一个上限值, 此时围压和相对密度对颗粒破碎影响很小; 颗粒间的滑动标志着应力达到极限状态, 而颗粒破碎会阻碍应力达到极限状态, 在本实验中, 低围压时颗粒破碎少, 颗粒相对运动形式为滑移, 使应力-应变曲线为软化型, 高围压下颗粒破碎严重, 颗粒破碎在剪切过程中始终发生, 使应力-应变曲线呈应变硬化型; 颗粒破碎使体变从剪胀逐渐发展到剪缩, 且破碎越严重剪缩越严重; 在低围压下钙质砂强度主要由剪胀和咬合提供, 高围压下颗粒破碎严重, 剪胀消失, 咬合减小, 使峰值摩擦角减小, 抗剪强度降低。 相似文献
4.
目前对钙质土压缩特性的研究主要集中在钙质细砂,而实际工程中广泛存在钙质粗粒料,因此对钙质粗粒料压缩特性开展研究具有重要意义。通过颗粒强度测定仪和全自动大型固结仪对钙质土进行了单颗粒破碎试验和一维压缩试验,研究了颗粒粒径和相对密度对钙质粗粒料的颗粒强度和压缩特性的影响。单颗粒试验结果表明,钙质砂单颗粒的特征应力随着颗粒相对密度的增大而增大;单颗粒的破碎强度具有明显的尺寸效应,可利用单颗粒的特征应力进行标准化,且服从Weibull分布。压缩试验结果表明,单一粒径试样破碎后的分形维数随颗粒粒径的增大而增大;试样的Hardin破碎率与塑性功的关系为幂函数关系;在本次试验条件下,单一粒径试样的屈服应力与单颗粒的特征应力存在近似线性关系。 相似文献
5.
In granular soils grain crushing reduces dilatancy and stress obliquity enhances crushability. These are well-supported specimen-scale experimental observations. In principle, those observations should reflect some peculiar micromechanism associated with crushing, but which is it? To answer that question the nature of crushing-induced particle-scale interactions is here investigated using an efficient DEM model of crushable soil. Microstructural measures such as the mechanical coordination number and fabric are examined while performing systematic stress probing on the triaxial plane. Numerical techniques such as parallel and the newly introduced sequential probing enable clear separation of the micromechanical mechanisms associated with crushing. Particle crushing is shown to reduce fabric anisotropy during incremental loading and to slow fabric change during continuous shearing. On the other hand, increased fabric anisotropy does take more particles closer to breakage. Shear-enhanced breakage appears then to be a natural consequence of shear-enhanced fabric anisotropy. The particle crushing model employed here makes crushing dependent only on particle and contact properties, without any pre-established influence of particle connectivity. That influence does not emerge, and it is shown how particle connectivity, per se, is not a good indicator of crushing likelihood. 相似文献
6.
珊瑚砂是一种含钙极高的海洋生物成因材料,具有高棱角性、形状不规则、易破碎等特点。通过珊瑚砂的高压一维蠕变试验,研究颗粒破碎引起颗粒分布曲线和形状因子的演化规律。借助于高速动态图像的激光粒度粒形仪器,从统计学的角度分析试验前后颗粒形状随压力演化的关系,发现颗粒的形状因子,如长宽比、球形度和凹凸度等,随压力增加而逐渐增加。不同粒径的颗粒形状因子均向一个窄幅范围趋近,说明颗粒破碎具有无尺度性和自相似性的分形特性,分形维数随压力增加而逐渐增大,且趋近分形破碎极限。采用Hardin和Einav的方法计算相对破碎量,发现在两种计算方法下相对破碎量与压力呈幂函数关系,且幂指数相同。相对破碎量随时间增加的现象并不明显,说明在高压力下颗粒破碎主要为压缩破碎,且颗粒细化滑移填充孔隙引起的变形是造成蠕变的主要原因。 相似文献
7.
The paper provides an in-depth exploration of the role of particle crushing on particle kinematics and shear banding in sheared granular materials. As a two-dimensional approximation, a crushable granular material may be represented by an assembly of irregularly shaped polygons to include shape diversity of realistic granular materials. Particle assemblies are subjected to biaxial shearing under flexible boundary conditions. With increasing percentage of crushed particles, mesoscale deformation becomes increasingly unstable. Fragmented deformation patterns within the granular assemblies are unable to form stable and distinct shear bands. This is confirmed by the sparsity of large fluctuating velocities in highly crushable assemblies. Without generating distinct shear bands, deformation patterns and failure modes of a highly crushable assembly are similar to those of loose particle assemblies, which are regarded as diffuse deformation. High degrees of spatial association amongst the kinematical quantities confirm the key role that non-affine deformation and particle rotation play in the generation of shear bands. Therefore, particle kinematical quantities can be used to predict the onset and subsequent development of shear zones, which are generally marked by increased particle kinematic activity, such as intense particle rotation and high granular temperature. Our results indicate that shear band thickness increases, and its speed of development slows down, with increasing percentage of crushed particles. As particles crush, spatial force correlation becomes weaker, indicating a more diffuse nature of force transmission across particle contacts. 相似文献
8.
Empirical evidence has shown that particle breakage affects the mechanical behaviour of granular materials. The source of this mechanism takes place at the particle scale, and the main consequence on the macromechanical behaviour is increasing compressibility. Due to the inverse correlation between particle size and particle crushing strength, coarse rockfill materials are particularly vulnerable to mechanical degradation due to particle breakage. However, such coarse materials do not fit in standard laboratory devices, and the alternative of large sample testing is usually unavailable or too expensive. Alternatively, recent works have proposed multi-scale approaches using the discrete element method (DEM) to carry out numerical testing of coarse crushable materials, although few studies have focused on size effects. This article presents the application of a DEM bonded-cell model to study particle size-strength correlation on angular rock aggregates. Each particle is modelled by a cluster of perfectly rigid polyhedral cells with Mohr–Coulomb contact law. Constant cell density within particles implies that the presence of potential fragmentation planes increases with size. Therefore, particle strength decreases with size. A comprehensive sensitivity analysis was carried out through 1477 particle crushing simulations in a given particle size. Based on published experimental data on calcareous rock aggregates, part of the simulations were used for calibration, and 97 additional simulations of a coarser size fraction were performed for validation. The results show a good agreement with the empirical data in terms of size effect and data scatter through Weibull statistics. 相似文献
9.
Crushability is one of the important behaviors of granular materials particularly under high stress states, and affects both the deformability and strength of the materials that are in essence associated with state‐dependent dilatancy. In this presentation, first, a new critical state model is proposed to take into account the three different modes of compressive deformation of crushable granular materials, i.e. particle rearrangement, particle crushing and pseudo‐elastic deformation. Second, the governing equations for cavity expansion in crushable granulates are introduced, in which the state‐dependent dilatancy as well as the bounding surface plasticity model are used. Then, the procedure to obtain semi‐analytical solutions to cavity expansion in the material is described in detail, in which a commercial differential equation solver is employed. Finally, cavity expansion analyses are carried out on Toyoura sand, a well‐documented granular material, to demonstrate the effects of crushability and state‐dependent dilatancy. The study shows that particle crushing does occur at both high stress and critical states and affects the stress fields and the deformation behavior of the material surrounding the cavity in association with state‐dependent dilatancy. This leads to conclusion that particle crushing and state‐dependent dilatancy have to be taken into account when cavity expansion theory is used to interpret cone penetration tests and pressuremeter tests. Copyright © 2011 John Wiley & Sons, Ltd. 相似文献
10.
This article presents a fundamental study on the role of particle breakage on the shear behavior of granular soils using the three‐dimensional (3‐D) discrete element method. The effects of particle breakage on the stress ratio, volumetric strain, plastic deformation, and shear failure behavior of dense crushable specimens undergoing plane strain shearing conditions are thoroughly investigated through a variety of micromechanical analyses and mechanism demonstrations. The simulation of a granular specimen is based on the effective modeling of realistic fracture behavior of single soil particles, which is demonstrated by the qualitative agreement between the results from platen compression simulations and those from physical laboratory tests. The simulation results show that the major effects of particle breakage include the reduction of volumetric dilation and peak stress ratio and more importantly the plastic deformation mechanisms and the shear failure modes vary as a function of soil crushability. Consistent macro‐ and micromechanical evidence demonstrates that shear banding and massive volumetric contraction depict the two end failure modes of a dense specimen, which is dominated by particle rearrangement–induced dilation and particle crushing–induced compression, respectively, with a more general case being the combination and competition of the two failure modes in the medium range of soil crushability and confining stress. However, it is further shown that a highly crushable specimen will eventually develop a shear band at a large strain because of the continuous decay of particle breakage. Copyright © 2011 John Wiley & Sons, Ltd. 相似文献
11.
In order to simulate undrained conditions using the discrete element method, a constant sample volume is often assumed. There are well-recognised problems with these constant-volume triaxial simulations, particularly of dense samples, which inhibit quantitative comparison with laboratory experiments. In this paper, four possible explanations for these problems with conventional constant-volume simulations of ideal spherical particles are explored, each of which has a physical basis: particle crushing, the presence of highly compressible air within the sample, or the reduction in stiffness due to particle surface asperities or non-spherical particle shapes. These options are explored independently and in combination through implementation in the open-source LAMMPS code. In situations where a significant amount of particle crushing occurs, it is important to incorporate this in the simulations so that stresses are not over-estimated. There is experimental evidence that irregular particles have lower Young’s moduli than the Hertzian spheres often used in DEM. In the absence of particle crushing, the most effective method to achieve more realistic stress–strain responses is to reduce the particle shear modulus substantially. This approach has the added computational benefit of enabling an increase in the simulation time-step. 相似文献
12.
针对岛礁大型构筑物修建过程中由于高应力而导致作为地基材料的钙质砂发生破碎,进而引发地基沉降变形问题。本文采用高压固结仪对钙质砂开展了一系列终止压力为16 MPa的侧限压缩试验,研究了高应力水平下钙质砂的压缩破碎特性。同时基于显微图像采集和处理技术对钙质砂颗粒的形状参数(圆度和完整度)进行了定量化表征,研究了钙质砂的形状分布规律。最终分别探讨了级配特征(如平均粒径、不均匀系数)、形貌特征等因素对钙质砂压缩和破碎特性的影响。结果表明:随着平均粒径的增大,钙质砂颗粒的形状不规则程度逐渐增加,其棱角也越发育。随着竖向应力的增大,在e-logp平面内,不同粒径钙质砂的压缩曲线逐渐会聚并相交于一条直线,初始粒径对其压缩特性的影响逐渐减小以致消失。而不同级配钙质砂的压缩曲线也发生会聚,但未相交于一条直线。当试样的不均匀系数(C u)相近时,其压缩破碎量随着平均粒径(d 50)的增大而逐渐增加,当试样的d 50相近时,其压缩破碎量随着C u增大而逐渐减小。上述研究成果将对南海岛礁大型工程建设提供重要科学依据。 相似文献
13.
珊瑚单颗粒破碎特性与珊瑚砂高压缩性、剪缩性及良好蠕变性等宏观力学行为密切相关。珊瑚颗粒的应变率效应对于不同形式荷载作用下珊瑚砂强度与变形特性研究具有重要意义。对约300颗珊瑚颗粒进行0.1～50 mm/min位移速率下的单颗粒破碎试验,探讨加载应变速率对颗粒破碎强度、破碎模式、破碎能量及破碎分形的影响。结果表明,珊瑚颗粒破碎强度服从Weibull分布规律,且特征破碎强度随应变率的提高非线性增大;随着加载速率的增大,颗粒主劈裂破坏往往先于棱角的局部碎裂和表面研磨,相应的荷载?位移曲线呈现出由峰前“多峰”向峰后“多峰”现象转变;珊瑚颗粒破碎能量密度和破碎分形维数同样具有明显的应变率效应,且均与对数应变率呈线性正相关关系,表征能量耗散和破碎程度均随加载应变率的增大而增大。 相似文献
14.
颗粒破碎对颗粒材料宏观力学行为有重要影响。 结合Hardin的破碎经验公式,将表征破碎程度的破碎参量与Cosserat连续体的内部长度参数相关联,形成一个基于Cosserat连续体且能考虑颗粒破碎的弹塑性模型。数值算例主要考察了颗粒破碎对颗粒材料承载能力、塑性应变及局部化行为的影响,数值结果表明,颗粒破碎主要发生在剪切带内,颗粒破碎使得剪切带明显变窄且剪切带内外等效塑性应变梯度明显增大。 相似文献
15.
基于二维离散单元法,对沉桩过程中钙质砂颗粒破碎情况进行了模拟。采用簇粒来模拟易破碎的钙质砂颗粒,并用形状与变形特性相同的聚粒单元来模拟不可破碎颗粒,对这两种单元特性进行对比,分析不同桩型的沉桩过程、桩周土体的力学响应、沉桩过程中钙质砂的颗粒破碎现象。结果表明：破碎颗粒将引起桩侧土体级配的重新调整,与桩体接触好于不可破碎土体;桩处于颗粒破碎的钙质砂中,其沉桩速度较快,对地基土扰动小于未发生颗粒破碎的情况;对于不同桩型、不同土层,桩体压入过程中,桩周土体应力场分布具有相似性;靠近桩端附近,土中水平应力和竖向应力急剧增大,形成应力核;同等条件下发生颗粒破碎的钙质砂地基土中,桩端应力峰值高于不可破碎土体。 相似文献
16.
通过6种典型堆石块体的形状近似,分别采用两种接触本构模型建立了多块体形状堆石体离散元数值模型,研究堆石体在碾压荷载作用下的颗粒破碎过程,建立颗粒破碎的量化计算方法,分析碾压前、后堆石级配曲线的变化,讨论接触本构模型和颗粒形状对块体破碎的影响。模拟结果显示,碾压荷载下堆石颗粒以张拉破碎为主,随着碾压遍数的增加,局部开始出现剪切破碎;提出的颗粒破碎量化计算方法,在大粒径范围对粒径变化幅度预测偏大,但级配曲线整体趋势与实测结果比较吻合;相比较于接触连接模型,平行连接模型与现场碾压试验结果更接近。6种块体形状的数值结果显示,随着形状系数的增加,在其他条件不变的情况下颗粒破碎率逐渐降低,其中类长方形块体在碾压荷载作用下颗粒破碎最明显。相比较于纯圆颗粒或者单一非圆颗粒,采用的6种颗粒形状建立的堆石体振动碾压离散元模型,更接近现场实际情况。 相似文献
17.
针对取自我国南部某海域的钙质砂样本,做了以下两方面工作：一是通过电子显微镜获取了钙质砂颗粒的几何投影图像,利用图像处理技术对图形进行黑白二值化处理,获取单元颗粒形状轮廓边界,使用圆度和粗糙度2个参数对钙质砂的颗粒形状进行定义和量化。二是通过不同围压下的三轴固结排水剪切试验及试验前后的颗分测量对比,研究了颗粒破碎对钙质砂的变形、强度、能量耗散等特性的影响。研究表明,大粒径钙质砂（粒径大于2.0 mm）和小粒径钙质砂（粒径小于0.5 mm）形态比较接近圆形、颗粒表面相对光滑;相比而言,中间粒径（粒径介于0.5～2.0 mm之间）钙质砂形状较不规则,表面棱角较多。钙质砂在三轴排水剪切过程中发生颗粒破碎,试样向着级配均匀的方向发展。随着初始围压的增大,颗粒破碎程度加大,土样整体剪胀趋势减小,而破碎引起的能量耗散增加。而在高围压（初始围压为600 kPa）剪切过程中,仅考虑摩擦耗散,以及同时考虑摩擦、体积耗散两种情况下,计算得到的最大颗粒破碎耗散分别可达土样总输入塑性功的25%和18%。 相似文献
18.
It is well known that the compressibility of crushable granular materials increases with the moisture content,due to the decrease of particle strength in a humid environment.An existing approach to take into account the effect of grain breakage in constitutive modeling consists in linking the evolution of the grain size distribution to the plastic work.But how the material humidity can affect this relationship is not clear,and experimental evidence is quite scarce.Based on compression tests on dry and saturated crushable sand recently reported by the present authors,a new non-linear relationship is proposed between the amount of particle breakage and the plastic work.The expression contains two parameters:(1)a material constant dependent on the grain characteristics and(2)a constant depending on the wetting condition(in this study,dry or saturated).A key finding is that the relationship does not depend on the stress path and,for a given wetting condition,only one set of parameters is necessary to reproduce the results of isotropic,oedometric,and triaxial compression tests.The relationship has been introduced into an elastoplastic constitutive model based on the critical state concept with a double yield surface for plastic sliding and compression.The breakage ratio is introduced into the expression of the elastic stiffness,the critical state line and the hardening compression pressure.Incremental stress-strain computations with the model allow the plastic work to be calculated and,therefore,the evolution of particle crushing can be predicted through the proposed non-linear relationship and reintroduced into the constitutive equations.Accurate predictions of the experimental results in terms of both stress-strain relationships and breakage ratio were obtained. 相似文献
19.
Calcareous sand is a typical problematic marine sediment because of its angular and porous particles. The effects of internal pores on the mechanical properties of calcareous sand particles have rarely been investigated. In this paper, the apparent morphology and internal structure of calcareous sand particles are determined by scanning electron microscopy and computed tomography tests, finding that the superficial pores connect inside and outside of the particles, forming a well-developed network of cavities and an internal porosity of up to 40%. The effects of particle morphology and internal porosity on the mechanical responses of particle were investigated by conducting photo-related compression test and 3D numerical simulations. Two failure modes are observed for the porous calcareous sand, i.e., compressive failure indicates that the particle skeleton is continually compressed and fragmented into small detritus without obvious splitting, and tensile failure indicates that the particles are broken into several fragments when the axial force clearly peaks. Calcareous sand particles with a high internal porosity or with small and dense pores often exhibit compressive failure, and vice versa. The particle strength is considerably reduced by increasing the internal porosity, but affected by pore size in nonlinear correlation. The crushing stress–strain points can be well fitted by an exponential curve, which is supplied for discussion. 相似文献
20.
Breakage of particles will have greatly influence on mechanical behavior of granular material(GM)under external loads,such as ballast,rockfill and sand.The discrete element method(DEM)is one of the most popular methods for simulating GM as each particle is represented on its own.To study breakage mechanism of particle breakage,a cohesive contact mode is developed based on the GPU accelerated DEM code-Blaze-DEM.A database of the 3D geometry model of rock blocks is established based on the 3D scanning method.And an agglomerate describing the rock block with a series of non-overlapping spherical particles is used to build the DEM numerical model of a railway ballast sample,which is used to the DEM oedometric test to study the particles’breakage characteristics of the sample under external load.Furthermore,to obtain the meso-mechanical parameters used in DEM,a black-analysis method is used based on the laboratory tests of the rock sample.Based on the DEM numerical tests,the particle breakage process and mechanisms of the railway ballast are studied.All results show that the developed code can better used for large scale simulation of the particle breakage analysis of granular material. 相似文献
|
