共查询到20条相似文献，搜索用时 468 毫秒
1.
A cross-hole Electrical Resistivity Tomography (ERT) study was undertaken near the center of Thessaloniki in order to detect the depth of the existing city walls in the planned route of the new city underground train. This cross-hole setup was used for a study of measurements with various electrode arrays in real urban field conditions to evaluate the resolution of the models which is produced by each array and the reliability of the models which is produced by the newly published “MOST” technique. The pole–tripole array (C2–C1P1P2) produces high resolution models, even when only borehole electrodes are used. The bipole–bipole C1C2–P1P2 array, when used for cross-hole measurements only, produces higher resolution models compared to the C1P1–C2P2 array, even with a lower signal-to-noise ratio, which can result in extremely high RMS error, when noise, systematic or not, must be faced. The models of both arrays are greatly improved by the use of surface electrodes. The pole–bipole array (C1–P1P2) is proved to be less accurate in imaging and quite unstable to the noisy urban environment and to systematic errors. Furthermore, the Model Stacking (MOST) interpretation technique leads to better results with models of greater resolution and fewer artifacts compared even with the combined data inversion. Finally, the ERT cross-hole analysis has been reliable in detecting the city walls. 相似文献
2.
Two‐dimensional joint inversions of cross‐hole resistivity data and resolution analysis of combined arrays 
下载免费PDF全文
下载免费PDF全文 In this study, a new two‐dimensional inversion algorithm was developed for the inversion of cross‐hole direct current resistivity measurements. In the last decades, various array optimisation methods were suggested for resistivity tomography. However, researchers have still collected data by using classical electrode arrays in most cross‐hole applications. Therefore, we investigated the accuracy of both the individual and the joint inversion of the classical cross‐hole arrays by using both synthetic and field data with the developed algorithm. We showed that the joint inversion of bipole–bipole, pole–bipole, bipole–pole, and pole–tripole electrode arrays gives inverse solutions that are closer to the real model than the individual inversions of the electrode array datasets for the synthetic data inversion. The model resolution matrix of the suggested arrays was used to analyse the inversion results. This model resolution analysis also showed the advantage of the joint inversion of bipole–bipole, pole–bipole, bipole–pole, and pole–tripole arrays. We also used sensitivity sections from each of the arrays and their superpositions to explain why joint inversion gives better resolution than the any individual inversion result. 相似文献
3.
Out‐of‐plane effects in 2D borehole‐to‐surface resistivity tomography and applications in mineral exploration 下载免费PDF全文
下载免费PDF全文 In this paper, we discuss the effects of anomalous out‐of‐plane bodies in two‐dimensional (2D) borehole‐to‐surface electrical resistivity tomography with numerical resistivity modelling and synthetic inversion tests. The results of the two groups of synthetic resistivity model tests illustrate that anomalous bodies out of the plane of interest have an effect on two‐dimensional inversion and that the degree of influence of out‐of‐plane body on inverted images varies. The different influences are derived from two cases. One case is different resistivity models with the same electrode array, and the other case is the same resistivity model with different electrode arrays. Qualitative interpretation based on the inversion tests shows that we cannot find a reasonable electrode array to determine the best inverse solution and reveal the subsurface resistivity distribution for all types of geoelectrical models. Because of the three‐dimensional effect arising from neighbouring anomalous bodies, the qualitative interpretation of inverted images from the two‐dimensional inversion of electrical resistivity tomography data without prior information can be misleading. Two‐dimensional inversion with drilling data can decrease the three‐dimensional effect. We employed two‐ and three‐dimensional borehole‐to‐surface electrical resistivity tomography methods with a pole–pole array and a bipole–bipole array for mineral exploration at Abag Banner and Hexigten Banner in Inner Mongolia, China. Different inverse schemes were carried out for different cases. The subsurface resistivity distribution obtained from the two‐dimensional inversion of the field electrical resistivity tomography data with sufficient prior information, such as drilling data and other non‐electrical data, can better describe the actual geological situation. When there is not enough prior information to carry out constrained two‐dimensional inversion, the three‐dimensional electrical resistivity tomography survey is the better choice. 相似文献
4.
I used theoretical forward models to show that a cavity embedded in a stratified sedimentary sequence can induce an equivalence problem in the ERT data inversion. Conductive top soil increases the misfit between the ground feature and the ERT model. The misfit depends on array and stratigraphy sequences. The latter induce an equivalence problem that manifests itself as wrong cavity depth positioning. The misfit is greater in the data acquired with Schlumberger array than with dipole–dipole.The ambiguity of ERT data inversion problems was tested in the detection of cavities linked to an 8th–6th century B.C. Sabine tomb, 3 m wide × 3 m long × 2 m high, excavated from a shaly gray volcanic ash (cinerite) layer covered by semi-lithoid tuff and top soil layers. In the real study I reduced the ambiguity in the inverse problem of ERT data using a priori information on geometry and resistivity of the cavity. The constrains were carried out from georadar data acquired with 80 and 200 MHz antenna. I demonstrate that this procedure has a practical application in cavity detection, and is a key to the reduction of the uncertainty inherent in the inversion process of ERT data. 相似文献
5.
综合地球物理技术在采空区的探测中发挥了重要作用.目前通常采用单方法反演、仅对不同方法反演结果进行对比解释的综合勘探方式,单方法反演的多解性严重降低了其探测精度.如何提高采空区的探测精度,对采空区进行有效探测一直被认为是地球物理技术面临的首要难题.为了提高地震与电法技术的探测精度,基于交叉梯度联合反演理论,设计了地震初至折射走时数据和高密度电法数据的联合反演算法流程,对采空区理论模型和野外实际数据进行了联合反演处理.结果发现通过两者的联合反演,不仅可以提高采空区电阻率反演模型的成像效果,而且能够获得地震单方法反演难以成像的采空区低速异常体,从而提高了地震与电法技术对采空区的探测精度.表明地震与电法探测数据联合反演是一种提高采空区探测精度的有效方法. 相似文献
6.
Marc Descloitres Olivier Ribolzi Yann Le Troquer Jean Pierre Thibaux 《Journal of Applied Geophysics》2008,64(3-4):83-98
Herbaceous vegetation in the Sahel grows almost exclusively on sandy soils which preferentially retain water through infiltration and storage. The hydrological functioning of these sandy soils during rain cycles is unknown. One way to tackle this issue is to spatialize variations in water content but these are difficult to measure in the vadose zone. We investigated the use of Electrical Resistivity Tomography (ERT) as a technique for spatializing resistivity in a non-destructive manner in order to improve our knowledge of relevant hydrological processes. To achieve this, two approaches were examined. First, we focused on a possible link between water tension (which is much easier to measure in the field by point measurements than water content), and resistivity (spatialized with ERT). Second, because ERT is affected by solution non-uniqueness and reconstruction smoothing, we improved the accuracy of ERT inversion by comparing calculated solutions with in-situ resistivity measurements. We studied a natural microdune during a controlled field experiment with artificial sprinkling which reproduced typical rainfall cycles. We recorded temperature, water tension and resistivity within the microdune and applied surface ERT before and after the 3 rainfall cycles. Soil samples were collected after the experiment to determine soil physical characteristics. An experimental relationship between water tension and water content was also investigated. Our results showed that the raw relationship between calculated ERT resistivity and water tension measurements in sand is highly scattered because of significant spatial variations in porosity. An improved correlation was achieved by using resistivity ratio and water tension differences. The slope of the relationship depends on the soil solution conductivity, as predicted by Archie's law when salted water was used for the rain simulation. We found that determining the variations in electrical resistivity is a sensitive method for spatializing the differences in water tension which are directly linked with infiltration and evaporation/drainage processes in the vadose zone. However, three factors complicate the use of this approach. Firstly, the relation between water tension and water content is generally non-linear and dependent on the water content range. This could limit the use of our site-specific relations for spatializing water content with ERT through tension. Secondly, to achieve the necessary optimization of ERT inversion, we used destructive resistivity measurements in the soil, which renders ERT less attractive. Thirdly, we found that the calculated resistivity is not always accurate because of the smoothing involved in surface ERT data inversion. We conclude that further developments are needed into ERT image reconstruction before water tension (and water content) can be spatialized in heterogeneous sandy soils with the accuracy needed to routinely study their hydrological functioning. 相似文献
7.
本文提出了能提高异常体分辨能力,同时得到绝对电导率的地面磁电阻率数据三维反演方法.磁电阻率响应用准直流的低频磁场代替;数值模拟由频率域电场满足的Helmholtz方程出发,采用三维交错网格有限差分法;长直导线源作为发射源,其中源的计算包含在背景场中;结合地面磁电阻率数据各分量的特点,选择y分量进行反演研究;反演采用三维非线性共轭梯度反演技术,为了提高异常体的深度分辨能力,进行迭代重构反演;用印模法对初始模型进行重构,采用的是辅模型在浅部,元模型在深部的组合方式.从合成数据和实际数据的反演结果可以得到以下的认识:(1)由频率域麦克斯韦方程组出发,低频磁场数据反演可以直接得到电导率,而不是相对电导率之比;(2)采用印模法组合初始模型,进行迭代重构反演,可以提高地面磁电阻率数据反演对异常体的分辨能力,确定埋深位置,同时不会丧失对于浅部异常体的分辨能力;(3)在结合印模法的地面磁电阻率数据三维反演中,深部异常体的分辨能力受地表不均匀导电体影响较小;(4)确定印模深度可以采用上一次重构反演结束时的模型变化量,通过相邻两次重构反演结束时的模型变化量之差来确定迭代重构是否终止.因为静磁场与重力场在数学上的相似性,本文的反演方法可以被运用到重力场等位场的地面数据的反演中. 相似文献
8.
9.
This paper investigates the relative merits and effectiveness of cross‐hole resistivity tomography using different electrode configurations for four popular electrode arrays: pole–pole, pole–bipole, bipole–pole and bipole–bipole. By examination of two synthetic models (a dipping conductive strip and a dislocated fault), it is shown that besides the popular pole–pole array, some specified three‐ and four‐electrode configurations, such as pole–bipole AM–N, bipole–pole AM–B and bipole–bipole AM–BN with their multispacing cross‐hole profiling and scanning surveys, are useful for cross‐hole resistivity tomography. These configurations, compared with the pole–pole array, may reduce or eliminate the effect of remote electrodes (systematic error) and yield satisfactory images with 20% noise‐contaminated data. It is also shown that the configurations which have either both current electrodes or both potential electrodes in the same borehole, i.e. pole–bipole A–MN, bipole–pole AB–M and bipole–bipole AB–MN, have a singularity problem in data acquisition, namely low readings of the potential or potential difference in cross‐hole surveying, so that the data are easily obscured by background noise and yield images inferior to those from other configurations. 相似文献
10.
This paper describes a series of experiments that tested the ability of the electrical resistivity tomography (ERT) method to locate correctly wet and dry fractures in a meso-scale model. The goal was to develop a method of monitoring the flow of water through a fractured rock matrix. The model was a four by six array of limestone blocks equipped with 28 stainless steel electrodes. Dry fractures were created by placing pieces of vinyl between one or more blocks. Wet fractures were created by injecting tap water into a joint between blocks. In electrical terms, the dry fractures are resistive and the wet fractures are conductive. The quantities measured by the ERT system are current and voltage around the outside edge of the model. The raw ERT data were translated to resistivity values inside the model using a three-dimensional Occam's inversion routine. This routine was one of the key components of ERT being tested. The model presented several challenges. First, the resistivity of both the blocks and the joints was highly variable. Second, the resistive targets introduced extreme changes the software could not precisely quantify. Third, the abrupt changes inherent in a fracture system were contrary to the smoothly varying changes expected by the Occam's inversion routine. Fourth, the response of the conductive fractures was small compared to the background variability. In general, ERT was able to locate correctly resistive fractures. Problems occurred, however, when the resistive fracture was near the edges of the model or when multiple fractures were close together. In particular, ERT tended to position the fracture closer to the model center than its true location. Conductive fractures yielded much smaller responses than the resistive case. A difference-inversion method was able to correctly locate these targets. 相似文献
11.
A 3D ERT study of solute transport in a large experimental tank 总被引：2，自引：0，他引：2
L. Slater A. Binley R. Versteeg G. Cassiani R. Birken S. Sandberg 《Journal of Applied Geophysics》2002,49(4)
A high resolution, cross-borehole, 3D electrical resistivity tomography (ERT) study of solute transport was conducted in a large experimental tank. ERT voxels comprising the time sequence of electrical images were converted into a 3D array of ERT estimated fluid conductivity breakthrough curves and compared with direct measurements of fluid conductivity breakthrough made in wells. The 3D ERT images of solute transport behaviour were also compared with predictions based on a 3D finite-element, coupled flow and transport model, accounting for gravity induced flow caused by concentration differences.The tank (dimensions 185×245×186 cm) was filled with medium sand, with a gravel channel and a fine sand layer installed. This heterogeneous system was designed to complicate solute transport behaviour relative to a homogeneous sand tank, and to thus provide a challenging but insightful analysis of the ability of 3D ERT to resolve transport phenomena. Four ERT arrays and 20 piezometers were installed during filling. A NaCl tracer (conductivity 1.34 S/m) was injected and intensively monitored with 3D ERT and direct sampling of fluid chemistry in piezometers.We converted the bulk conductivity estimate for 250 voxels in the ERT imaged volume into ERT estimated voxel fluid conductivity by assuming that matrix conduction in the tank is negligible. In general, the ERT voxel response is in reasonable agreement with the shape of fluid conductivity breakthrough observed in six wells in which direct measurements of fluid conductivity were made. However, discrepancies occur, particularly at early times, which we attribute to differences between the scale of the image voxels and the fluid conductivity measurement, measurement errors mapped into the electrical inversion and artificial image roughness resulting from the inversion.ERT images revealed the 3D tracer distribution at 15 times after tracer injection. The general pattern and timing of solute breakthrough observed with ERT agreed with that predicted from the flow/transport modelling. However, the ERT images indicate a vertical component of tracer transport and preferential flow paths in the medium sand. We attribute this to transient vertical gradients established during tracer injection, and heterogeneity caused by sorting of the sand resulting from the filling procedure. In this study, ERT provided a unique dataset of 250 voxel breakthrough curves in 1.04 m3. The use of 3D ERT to generate an array of densely sampled estimated fluid conductivity breakthrough curves is a potentially powerful tool for quantifying solute transport processes. 相似文献
12.
Nikos G. Papadopoulos Myeong-Jong Yi Jung-Ho Kim Panagiotis Tsourlos Gregory N. Tsokas 《Journal of Applied Geophysics》2010,70(3):192-205
Tumuli are artificially erected small hills that cover monumental tombs or graves. In this work, the surface three-dimensional (3D) Electrical Resistivity Tomography (ERT) method, composed of dense parallel two-dimensional (2D) tomographies, was used to investigate the properties of the tumuli filling material and to resolve buried archaeological structures inside the tumuli.The effectiveness of the method was investigated by numerical modeling and through 3D inversion of synthetic apparent resistivity data. A resistivity model that simulates the inhomogeneous tumulus material and the tombs that are buried inside the tumulus was assumed. The Dipole–Dipole (DD), Pole–Dipole (PD), Pole–Pole (PP), Gradient (GRAD), Midpoint-Potential-Referred (MPR) and Schlumberger Reciprocal (SCR) arrays, which are suitable for multichannel resistivity instruments, were tested. The tumulus topography (pyramid or capsized cup) was incorporated into the inversion procedure through a distorted finite element mesh. The inversion procedure was based on a smoothness constrained Gauss–Newton algorithm in which the Active Constraint Balancing (ACB) method was also applied in order to enhance the least-squares resolving power and stability.Synthetic modeling showed that the different tumulus layers and the horizontal contact of the artificial tumulus material with the natural background soil were reconstructed by all of the tested electrode arrays. Generally, PD and the GRAD arrays comprise the optimum choices to investigate the subsurface properties of a tumulus and locate buried tombs. The MPR model was inferior to the GRAD model, while the DD, PP and SCR models had the poorest resolution. It was also shown that the inversion models are practically independent from the survey direction and the topography shape of the tumulus.The real field data collected employing the PD array along a small tumulus from the archaeological site of Vergina in northern Greece enhanced the synthetic modeling results. The inversion model outlined a number of archaeological structures that exhibit a high possibility to correlate with graves. Overall, this work signifies that the surface 3D ERT method can provide a valuable tool in the non-destructive archaeological exploration of tumuli. 相似文献
13.
地球物理学中关于电磁波勘探研究通常采用的是地球半空间模型.然而,对于几十公里的有限长电缆源（长偶极源）,远距离电磁波场探测必须要考虑电离层的影响,它是一个全空间问题.关于包含电离层、空气层和地球介质（我们称“地-电离层”模式）的电磁波场特征的研究在国外较少,国内几乎是空白.本文采用全空间积分方程法首先对小尺度的可控源电磁波场特征进行了研究,由于此时电离层的影响可忽略,它应该和半空间成熟的CSAMT模拟结果一致,对比结果表明,二者是一致的,验证了全空间模拟方法的可靠性和有效性.随后进行了50 km长电缆电离层和空气层高度都为100 km的“地-电离层”模式大尺度电磁波场模拟,以探讨大尺度可控源电磁波场的特征.给定频率的“地-电离层”模式电磁场的衰减曲线表明长电缆远距离电磁波场由于受电离层的作用存在衰减逐渐变小的过渡场和衰减变小的波导场.为了探讨复杂介质“地-电离层”模式电磁波特征,对“地-电离层”模式的典型地盾和地台多层介质模型进行了数值模拟,得到了偶极源长度50 km、电流200A、收发距离远达1600 km和2500 km的合理的电磁场结果.最后,对一简单含油储层结构模型进行了长偶极、大功率、远距离电磁波场响应计算.储层横向不均匀复杂结构模拟的结果表明,考虑电离层和大气层的“地-电离层”模式大尺度深层复杂介质模拟时,电磁场对深部目标体仍有很好的异常响应. 相似文献
14.
《Journal of Applied Geophysics》2008,66(3-4):111-120
Muro Leccese (Lecce) contains one the most important Messapian archaeological sites in southern Italy.The archaeological interest of the site arises from the discovery of the remains of Messapian walls, tombs, roads, etc. (4th–2nd centuries BC) in the neighbourhood. The archaeological remains were found at about 0.3 m depth.At present the site belongs to the municipality, which intends to build a new sewer network through it. The risk of destroying potentially interesting ancient archaeological structures during the works prompted an archaeological survey of the area. The relatively large dimensions of the area (almost 10,000 m2), together with time and cost constraints, made it necessary to use geophysical investigations as a faster means to ascertain the presence of archaeological items. Since the most important targets were expected to be located at a soil depth of about 0.3 m, a ground-penetrating radar (GPR) survey was carried out in an area located near the archaeological excavations. Unfortunately the geological complexity did not allow an easy interpretation of the GPR data.Therefore a 3D electrical resistivity tomography (ERT) scan was conducted in order to resolve these interpretation problems.A three-way comparison of the results of the dense ERT measurements parallel to the x axis, the results of the measurements parallel to the y axis and the combined results was performed.Subsequently the synthetic model approach was used to provide a better characterization of the resistivity anomalies visible on the ERT field data.The 3D inversion results clearly illustrate the capability to resolve in view of quality 3D structures of archaeological interest. According to the presented data the inversion models along one direction (x or y) seems to be adequate in reconstructing the subsurface structures.Naturally field data produce good quality reconstructions of the archaeological features only if the x-line and y-line measurements are considered together. Despite the increased computational time required by the 3D acquisition and 3D inversion schemes, good quality results can be produced. 相似文献
15.
Albert Casas Pietro L. Cosentino Gianluca Fiandaca Mahjoub Himi Josep M. Macias Raffaele Martorana Andreu Muñoz Lluís Rivero Roger Sala Imma Teixell 《Surveys in Geophysics》2018,39(6):1107-1124
An integrated geophysical survey has been conducted at the Tarragona’s Cathedral (Catalonia, NE Spain) with the aim to confirm the potential occurrence of archaeological remains of the Roman Temple dedicated to the Emperor Augustus. Many hypotheses have been proposed about its possible location, the last ones regarding the inner part of the Cathedral, which is one of the most renowned temples of Spain (twelfth century) evolving from Romanesque to Gothic styles. A geophysical project including electrical resistivity tomography (ERT) and ground probing radar (GPR) was planned over 1 year considering the administrative and logistic difficulties of such a project inside a cathedral of religious veneration. Finally, both ERT and GPR have been conducted during a week of intensive overnight surveys that provided detailed information on subsurface existing structures. The ERT method has been applied using different techniques and arrays, ranging from standard Wenner–Schlumberger 2D sections to full 3D electrical imaging with the advanced Maximum Yield Grid array. Electrical resistivity data were recorded extensively, making available many thousands of apparent resistivity data to obtain a complete 3D image after a full inversion. In conclusion, some significant buried structures have been revealed providing conclusive information for archaeologists. GPR results provided additional information about shallowest structures. The geophysical results were clear enough to persuade religious authorities and archaeologists to conduct selected excavations in the most promising areas that confirmed the interpretation of geophysical data. In conclusion, the significant buried structures revealed by geophysical methods under the cathedral were confirmed by archaeological digging as the basement of the impressive Roman Temple that headed the Provincial Forum of Tarraco, seat of the Concilium of Hispania Citerior Province. 相似文献
16.
We propose a Bayesian fusion approach to integrate multiple geophysical datasets with different coverage and sensitivity. The fusion strategy is based on the capability of various geophysical methods to provide enough resolution to identify either subsurface material parameters or subsurface structure, or both. We focus on electrical resistivity as the target material parameter and electrical resistivity tomography (ERT), electromagnetic induction (EMI), and ground penetrating radar (GPR) as the set of geophysical methods. However, extending the approach to different sets of geophysical parameters and methods is straightforward. Different geophysical datasets are entered into a trans-dimensional Markov chain Monte Carlo (McMC) search-based joint inversion algorithm. The trans-dimensional property of the McMC algorithm allows dynamic parameterisation of the model space, which in turn helps to avoid bias of the post-inversion results towards a particular model. Given that we are attempting to develop an approach that has practical potential, we discretize the subsurface into an array of one-dimensional earth-models. Accordingly, the ERT data that are collected by using two-dimensional acquisition geometry are re-casted to a set of equivalent vertical electric soundings. Different data are inverted either individually or jointly to estimate one-dimensional subsurface models at discrete locations. We use Shannon's information measure to quantify the information obtained from the inversion of different combinations of geophysical datasets. Information from multiple methods is brought together via introducing joint likelihood function and/or constraining the prior information. A Bayesian maximum entropy approach is used for spatial fusion of spatially dispersed estimated one-dimensional models and mapping of the target parameter. We illustrate the approach with a synthetic dataset and then apply it to a field dataset. We show that the proposed fusion strategy is successful not only in enhancing the subsurface information but also as a survey design tool to identify the appropriate combination of the geophysical tools and show whether application of an individual method for further investigation of a specific site is beneficial. 相似文献
17.
Geotechnical projects usually rely on traditional sounding and drilling investigations. Drilling only provides point information and the geology needs to be interpolated between these points. Near surface geophysical methods can provide information to fill those gaps. Norwegian case studies are presented to illustrate how two-dimensional electrical resistivity tomography (ERT) can be used to accurately map the extent of quick clay deposits. Quick clay may be described as highly sensitive marine clay that changes from a relatively stiff condition to a liquid mass when disturbed. Quick clay slides present a geo-hazard and therefore layers of sensitive clay need to be mapped in detail. They are usually characterized by higher resistivity than non-sensitive clay and ERT is therefore a suitable approach to identify their occurrence. However, our experience shows that ERT cannot resolve this small resistivity contrast near large anomalies such as a bedrock interface. For this reason, a constrained inversion of ERT data was applied to delineate quick clay extent both vertically and laterally. As compared to the conventional unconstrained inversions, the constrained inversion models exhibit sharper resistivity contrasts and their resistivity values agree better with in situ measurements. 相似文献
18.
为了对比天然源面波勘探不同台阵布局的探测效果, 筛选出探测成果可靠、 效率高和便于野外施工的天然源面波勘探台阵阵形, 在天水市黄土覆盖区的同一场地分别用4种常见的阵形进行数据采集试验, 并对各种阵形数据使用空间自相关法或扩展空间自相关法提取相应的频散曲线, 通过反演得到了试验点地下的浅层速度结构模型. 分析对比试验结果表明: 4种台阵提取的频散曲线数值很相近; 频散谱能量集中度较高的是嵌套式等边三角形和圆形台阵, L形和直线形台阵相对分散; L形台阵低频段(4—8 Hz)比直线形台阵差, 其高频段(8—40 Hz)比直线形台阵好. 针对直线形台阵在高频段信噪比较低的情况, 在确保探测成果可靠性的前提下, 为了提高探测效率, 提出了在同一直线形台阵开展天然源与人工源面波联合勘探的数据采集方法. 实验结果证实, 这种联合勘探方法不仅可弥补直线形台阵高频段的不足, 确保探测精度和结果的可靠性, 而且还能实现“高低”频兼顾, 即“深浅”兼顾. 相似文献
19.
JAN HELGESEN 《Geophysical Prospecting》1991,39(3):313-336
Three methods for least-squares inversion of receiver array-filtered seismic data are investigated: (1) point receiver inversion where array effects are neglected; (2) preprocessing of the data with an inverse array filter, followed by point receiver inversion; (3) array inversion, where the array effects are included in the forward modelling. The methods are tested on synthetic data generated using the acoustic wave equation and a horizontally stratified earth model. It is assumed that the group length and the group interval are identical. For arrays that are shorter than the minimum wavelength of the emitted wavefield, and when the data are appropriately muted, point receiver inversion (first method) gives satisfactory results. For longer arrays, array inversion (third method) should be used. The failure of the inverse array filter (second method) is due to aliasing problems in the data. 相似文献