共查询到19条相似文献,搜索用时 125 毫秒
1.
2.
探究合成纤维系缆损伤对绷紧式系泊系统响应的影响,具有重要的工程意义。通过高强聚乙烯(HMPE)缆绳损伤动刚度实验,获得其动刚度随损伤的演变规律。在数值计算上,借鉴并合理简化了前人提出的动刚度经验公式,通过处理实验结果确定动刚度经验公式的参数并进行验证。在此基础上,以一座采用高强聚乙烯缆绳为主体系缆的FPSO为例,将所得动刚度经验公式导入系泊分析软件,结合水动力分析,计算得到在相同海洋环境中,系缆发生不同程度损伤时,各系缆张力和平台偏移响应的结果。通过处理、分析所得的计算结果,获得合成纤维缆绳损伤演变对绷紧式系泊系统响应的影响规律,并据此为系缆更换提供了建议。这些成果既有利于把握绷紧式系泊系统的非线性动力响应,也对安全、经济、合理地运用合成纤维系缆具有重要意义。 相似文献
3.
在频域和时域内研究对等分布式系泊和分组式系泊2种系泊模式对Spar平台运动性能的影响,并分析单根系泊缆破断失效后平台运动性能的变化。首先建立Spar平台的三维水动力模型,通过在平台柱体导缆孔处指定预张力、倾角和刚度来模拟系泊系统的影响;然后采用三维势流理论进行浮体水动力计算,获得Spar平台运动响应的传递函数等水动力参数;最后根据实际海况资料,在平台生存工况下,进行Spar平台在完好系泊和单根系泊缆破断失效状态下运动响应的短期预报,并在时域内进行耦合分析,研究平台运动响应和系泊缆张力变化情况。研究结果对Spar平台系泊系统设计和平台设计前期运动性能研究有参考意义。 相似文献
4.
5.
基于我国南海海域环境条件,对一座深水圆筒型钻井平台设计一套张紧式系泊定位系统,利用SESAM软件对平台运动响应和缆索张力进行分析计算,得到主要运动响应为纵荡、纵摇和垂荡。分别考虑0°和180°的环境载荷方向,对比得到0°方向的缆索张力更大,且6号和7号缆承受了主要的环境力。分析了平台运动的影响因素,认为缆索夹角设定为35°时较优,适度增大系泊缆初始长度和减小两端锚链长度可较为有效地降低系泊缆受力,系泊缆总根数保持12时(4根×3组)为最优方案。根据分析结果对初始系泊方案进行了优化,在风暴工况下系泊缆最大受力减小了约14.8%。钻井作业工况和一根系泊缆破断工况下,系泊缆受力和平台位移均能满足规范要求。 相似文献
6.
7.
深水浮式平台垂荡运动与水下柔性立管涡激振动的动力耦合 总被引:1,自引:0,他引:1
基于有限元数值模拟,进行了"平台垂荡-顶张力立管涡激振动"整体系统的动响应数值模拟。动响应模型考虑了立管尾迹流场的水动力与结构动力的耦合和垂荡引起的立管结构刚度的时变特性;分析了平台垂荡运动的频率、模态阶数等因素对水下顶张力立管涡激振动的影响。数值结果表明:与不考虑平台运动相比,立管的动响应位移会增大;立管响应幅值随着模态阶数的降低而增大;在响应过程中,尤其对于低阶模态,会出现响应的模态转换现象。鉴于在平台垂荡和涡激振动的共同作用下,立管的动响应会大于涡激振动、参数激励分别单独作用的响应,建议在立管实际工程设计中应该考虑平台运动和涡激振动耦合激励作用下的结构动响应。 相似文献
8.
9.
10.
针对设计的新型双浮筒+Savinious型(S型)桨叶浮式防波堤的结构形式,基于势波理论和结构耦合水动力分析理论,利用面元积分和Newmark-β时间步进格式进行计算,研究其在线性规则波作用下的消波性能、运动响应和系泊张力响应,验证该结构的合理性。数值计算结果表明,阻尼修正后的防波堤纵摇运动响应合理,在波高H=1.5 m、波浪周期T=3 s下其消浪性能较为理想,透射系数达到0.65,同时系泊线张力呈周期响应并满足最大破断力的条件。此外,还研究了浮筒相对间距S1/L,浮筒—桨叶相对间距S2/L以及Savinious型桨叶高径比d/h三个无量纲关键几何参数对防波堤透射系数Ct和系泊线时域张力响应的影响。计算结果表明,浮筒间距S1越接近波长,防波堤消波性能越好,但迎浪侧张力响应幅值越大;随着浮筒—桨叶相对间距S2/L由0趋近于1,其透射系数随之减小,但迎浪侧张力响应幅值基本保持不变;减小桨叶的高径比d/h可以提高防波堤消波性能的稳定性,但张力响应幅值随之增大。 相似文献
11.
采用集中质量法研究了绷紧式系泊系统中系缆由于松弛-张紧过程产生的冲击张力。建立系泊缆绳离散的集中质量模型,对其独立单元进行受力分析并建立了单元的运动方程。给定缆绳上端点简谐激励,通过Ansys中的Aqwa模块,分析了缆绳的运动响应;针对缆绳运动响应过程中的三种状态进行了模拟计算,探讨了冲击张力产生的条件;研究了缆绳初始预张力、上端点激励幅值和频率、拖曳力系数、弹性模量以及单位长度质量对动态张力的影响。研究结果表明:这些影响因素不仅会影响缆绳动态张力的大小,也会对缆绳中的冲击张力产生一定的影响。 相似文献
12.
As a popular solution for mooring an FPSO (Floating Production, Storage and Offloading) permanently in shallow water, the soft yoke mooring system has been widely used in ocean oil production activities in the Bohai Bay of China. In order to simulate the interaction mechanism and conduct dynamic analysis of the soft yoke mooring system, a theoretical model with basic dynamic equations is established. A numerical iteration algorithm based on error estimation is developed to solve the equations and calculate the dynanfic response of the mooring system due to FPSO motions. Validation is conducted by wave basin experimentation. It is shown that the numerical simulation takes only a few iteration times and the final errors are small. Furthermore, the calculated results of both the static and dynamic responses agree well with those ones obtained by the model test. It indicates that the efficiency, the precision, the reliability and the validity of the developed numerical algorithm and program are rather good. It is proposed to develop a real-time monitoring system to further monitor the dynamic performance of the FPSO with a soft yoke mooring system under various real sea environments. 相似文献
13.
针对1 000 m水深作业的新型圆筒型浮式生产储卸油系统(FPSO),选择多点系泊FPSO和穿梭油轮串靠外输方案,分析串靠方案在中国南海的可行性。FPSO和穿梭油轮作业时两者之间相互影响的研究较为重要,通过ANSYS-AQWA建立水动力耦合分析模型,基于多浮体水动力学方法进行时域耦合仿真模拟。在FPSO作业海况下,分析了串靠外输时系泊锚链及系泊大缆的张力特性和两浮体的运动响应,对大缆的长度和刚度参数变化进行了分析。结果表明:串靠外输方案满足新型圆筒型FPSO的作业环境。随着系泊大缆长度增加,其张力最值逐渐减小,FPSO和穿梭油轮的最小间距逐渐增大。两浮体最小距离稳定在83 m左右。随着系泊大缆刚度增加,其张力最值增大,相比于大缆长度,大缆刚度对耦合系统的影响较弱。 相似文献
14.
15.
This paper presents a simulation model based on the finite element method. The method is used to analyze the motion response and mooring line tension of the flatfish cage system in waves. The cage system consists of top frames, netting, mooring lines, bottom frames, and floats. A series of scaled physical model tests in regular waves are conducted to verify the numerical model. The comparison results show that the simulated and the experimental results agree well under the wave conditions, and the maximum pitch of the bottom frame with two orientations is about 12o. The motion process of the whole cage system in the wave can be described with the computer visualized technology. Then, the mooring line tensions and the motion of the bottom frame with three kinds of weight are calculated under different wave conditions. According to the numerical results, the differences in mooring line tensions of flatfish cages with three weight modes are indistinct. The maximum pitch of the bottom frame decreases with the increase of the bottom weight. 相似文献
16.
17.
Mark A. Grosenbaugh 《Ocean Engineering》1996,23(1):7-25
An analytical model is proposed for predicting the dynamics of instrumented oceanographic surface moorings made up of a combination of wire rope and compliant synthetic rope. The model simplifies the problem by treating only the vertical motion of the buoy and the longitudinal motion of the mooring line and attached instruments. It is demonstrated using full-scale experimental data and numerical simulations, that the simplified model captures all of the important dynamic effects and gives accurate predictions of the dynamic tension at the top of the mooring line. The model shows that the total mass and damping of the instruments and wire rope that make up the stiff upper half of the mooring are the major sources of the dynamic tension. Damping of the instruments becomes a significant factor in larger sea states, especially near the peak frequency of the wave spectrum. Elastic stretching of the wire and synthetic rope make up approximately 10% of the total response. This is based on a coefficient of friction equal to 0.003 which fits the experimental data best. 相似文献
18.
在循环载荷作用下,合成纤维系缆的应力应变关系表现出明显的非线性特性,直接影响系泊缆绳的动力响应。如何针对其在循环载荷作用下的应力应变关系进行准确的定量描述是有关绷紧式系泊系统设计的关键问题。国内外研究者之前的研究不能反映缆绳的载荷历史、蠕变特性以及刚度变化过程,因此提出一个粘弹性粘塑性模型来描述合成纤维系缆的应力应变关系。本模型能够反映合成纤维缆绳的时间变化特性以及在整个加载—卸载过程中的刚度变化。此外,提出了明确的参数确定方法及步骤,基于简单的蠕变实验可以确定模型的各个参数。将两种载荷条件下聚酯缆绳的实验结果与模型结果进行对比,二者吻合较好,证明了模型的有效性和可靠性。本研究对于绷紧式系泊系统的研发和工程应用具有重要意义。 相似文献
19.
由于聚酯缆绳具备优异的力学性能,促使以其为主体系缆的绷紧式系泊系统得以广泛应用和发展。但聚酯系缆具有复杂的黏弹性和黏塑性,且由于在安装和使用过程中可能产生不同程度的损伤,使得聚酯系缆的动刚度特性发生演变,从而对系泊系统的动力响应产生直接影响。以一系泊于1 020 m水深的Spar平台为例,运用ABAQUS软件建立了由聚酯缆绳组成的系泊系统有限元模型,并利用ABAQUS子程序将损伤缆绳动刚度经验公式进行导入计算,以更好地反映系缆真实的动刚度变化。基于该有限元模型,计算了在相同水流、波浪工况下,不同损伤度、不同损伤系缆的系缆张力历程和平台的横荡、纵荡位移响应,分析了不同损伤度、不同损伤系缆对系缆张力及平台位移的影响。这些成果对把握绷紧式系泊系统在聚酯系缆有损伤情况下的非线性动力响应及其安全应用具有重要的参考价值。 相似文献