共查询到20条相似文献，搜索用时 312 毫秒
1.
Hydraulic Characteristics of Rough Fractures in Linear Flow under Normal and Shear Load 总被引：19，自引：3，他引：19
Summary
A hydro-mechanical testing system, which is capable of measuring both the flow rates and the normal and shear displacement
of a rock fracture, was built to investigate the hydraulic behaviour of rough tension fractures. Laboratory hydraulic tests
in linear flow were conducted on rough rock fractures, artificially created using a splitter under various normal and shear
loading. Prior to the tests, aperture distributions were determined by measuring the topography of upper and lower fracture
surfaces using a laser profilometer. Experimental variograms of the initial aperture distributions were classified into four
groups of geostatistical model, though the overall experimental variograms could be well fitted to the exponential model.
The permeability of the rough rock fractures decayed exponentially with respect to the normal stress increase up to 5 MPa.
Hydraulic behaviours during monotonic shear loading were significantly affected by the dilation occurring until the shear
stress reached the peak strength. With the further dilation, the permeability of the rough fracture specimens increased more.
However, beyond shear displacement of about 7 to 8 mm, permeability gradually reached a maximum threshold value. The combined
effects of both asperity degradation and gouge production, which prohibited the subsequent enlargement of mean fracture aperture,
mainly caused this phenomenon. Permeability changes during cyclic shear loading showed somewhat irregular variations, especially
after the first shear loading cycle, due to the complex interaction from asperity degradations and production of gouge materials.
The relation between hydraulic and mechanical apertures was analyzed to investigate the valid range of mechanical apertures
to be applied to the cubic law.
Received June 12, 2001; accepted February 26, 2002 Published online September 2, 2002 相似文献
2.
Yingchun Li Zhengzhao Liang Chun'an Tang Danqi Li Chuangzhou Wu 《国际地质力学数值与分析法杂志》2019,43(17):2687-2703
We present an analytical model for the shear behaviour of rock joints with progressive degradation of two-order asperities including waviness and unevenness. Critical waviness and critical unevenness are used to respectively represent the mechanical involvements of waviness and unevenness during shear. The degradation process of two-order asperities are predicted by considering the stepwise relationship among dilation angle, sheared and unsheared asperity areas, and plastic tangential work. The dilation angle of each asperity decreases as plastic tangential work accumulates. The progressive degradation transiting from critical unevenness to critical waviness is realised through examining the dilation angle and the unsheared area of critical unevenness. The model's predictions are compared with the experimental data from direct shear tests on both regular- and irregular-shaped joints. Good agreement between analytical and experimental curves demonstrate the credence of the proposed model. Therefore, the model, after implemented in finite and discrete element codes, is practicable for the stability assessment of rock-engineering structures. 相似文献
3.
微震、工程爆破等低应力循环剪切荷载作用对节理岩体工程失稳破坏具有重要影响。为研究峰前循环剪切加卸载作用下岩石节理剪切力学特性,采用RDS-200型岩石节理剪切试验系统对人工劈裂黄砂岩节理进行了峰前循环剪切下的直剪试验。通过与未进行峰前循环剪切加卸载时岩石节理力学参数预测值对比,得到峰前循环剪切加卸载作用对峰前剪切刚度、峰值剪切强度、峰值剪切位移与残余剪切强度的影响。结果表明：（1）峰前循环剪切加卸载后,当法向应力为2 MPa时,岩石节理峰前剪切刚度增大,当法向应力为4～10 MPa时,岩石节理峰前剪切刚度在循环剪切应力幅值范围内增大,在超出循环剪切应力幅值时减小;（2）峰前循环剪切加卸载后,峰值剪切强度降低了10%～20%,降低百分比随法向应力增大整体呈对数函数增大;峰值剪切位移增加了2%～40%,增加百分比随法向应力增大整体呈对数函数减小;（3）峰前循环剪切加卸载后,岩石节理残余剪切强度无明显变化,峰值剪切强度与残余剪切强度差值减小,峰后剪切应力做功损失百分比降低。 相似文献
4.
Microplane damage model for jointed rock masses 总被引：1，自引：0，他引：1
The paper presents a new microplane constitutive model for the inelastic behavior of jointed rock masses that takes into account the mechanical behavior and geometric characteristics of cracks and joints. The basic idea is that the microplane modeling of rock masses under general triaxial loading, including compression, requires the isotropic rock matrix and the joints to be considered as two distinct phases coupled in parallel. A joint continuity factor is defined as a microplane damage variable to represent the stress‐carrying area fraction of the joint phase. Based on the assumption of parallel coupling between the rock joint and the rock matrix, the overall mechanical behavior of the rock is characterized by microplane constitutive laws for the rock matrix and for the rock joints, along with an evolution law for the microplane joint continuity factor. The inelastic response of the rock matrix and the rock joints is controlled on the microplane level by the stress–strain boundaries. Based on the arguments enunciated in developing the new microplane model M7 for concrete, the previously used volumetric–deviatoric splits of the elastic strains and of the tensile boundary are avoided. The boundaries are tensile normal, compressive normal, and shear. The numerical simulations demonstrate satisfactory fits of published triaxial test data on sandstone and on jointed plaster mortar, including quintessential features such as the strain softening and dilatancy under low confining pressure, as well as the brittle–ductile transition under higher confining pressure, and the decrease of jointed rock strength and Young's modulus with an increasing dip angle of the joint. Copyright © 2014 John Wiley & Sons, Ltd. 相似文献
5.
在法向荷载和切向荷载的作用下岩体节理的剪切应力由抗剪断效应、剪胀效应和摩擦效应所引起的三部分应力构成,但三个组成部分在节理的剪切过程中并不是同时发挥其最大作用。在详细分析边坡岩体节理工程地质特性的基础上,提出一种节理分量式剪切本构模型,主要特征为（1）体现了剪胀与剪切之间的耦合效应;（2）采用分量式表达,物理意义更明确;（3）每一分量采用简单函数,避免了总量式分段构造函数的不足。在节理分量式本构模型基础上,提出应用于岩质节理边坡的双安全系数的概念和求解原则,双安全系数能够较好地反映岩体节理剪切破坏直至残余强度的物理过程。最后,通过双安全系数算例明确了各个分量对于边坡稳定性的贡献。 相似文献
6.
含二阶起伏体的模拟岩体节理试样剪切特性试验研究 总被引：1，自引：0，他引：1
利用规则的小尺寸锯齿构造二阶起伏体,对不同二阶起伏体高度的人工节理进行常法向应力下的直剪试验,研究了节理剪切力学特性。对节理的剪切强度、变形特征进行了分析,并对破坏特征做出解释。试验结果表明：二阶起伏体对节理剪切力学特性有重要影响,含二阶起伏体节理的剪切力学特性与只含有一阶起伏体节理的剪切力学特性不同,只含一阶起伏体的节理剪应力只有一个峰值,含二阶起伏体的节理会出现波浪状的剪胀曲线和多峰值剪应力,且峰值剪应力随剪切位移增大依次出现并逐个减小;随着二阶起伏体高度增大,节理峰值剪切强度增大,节理依次出现磨损破坏、多次性剪断破坏、一次性剪断破坏。 相似文献
7.
裂隙岩体流固耦合问题是目前国内外研究热点之一,采用离散元软件UDEC对裂隙岩体发生节理剪胀的渗透性变化规律进行了模拟分析。基于现场调查的裂隙信息统计生成裂隙网络岩体模型。 通过固定垂直应力、不断增加应力比RS(RS=水平应力/垂直应力)使岩体出现剪胀,采用库伦滑移节理模式对岩体在剪胀过程中的渗透性变化情况进行模拟。结果发现:当应力比较小(RS3.1)时,节理水力隙宽、流速、渗透系数等参数都随着应力比的增加表现出明显的降低; 而当岩体出现剪胀现象之后(应力比大于3.1),发生剪切滑移和剪胀现象的节理控制着裂隙岩体的总体渗流行为,与不考虑节理剪胀的计算结果相比,岩体渗透能力出现了显著增长。这一结果表明,剪胀对裂隙岩体渗透性的影响是显著而不可忽视的。 相似文献
8.
An Elasto-Plastic Constitutive Model for Rock Joints Under Cyclic Loading and Constant Normal Stiffness Conditions 总被引：1，自引：1，他引：0
An elasto-plastic constitutive model is introduced for rock joints under cyclic loading, considering the additional shear resistance generated by the asperity damage in the first forward shear cycle and sliding mechanism for further shearing. A series of cyclic loading direct shear tests was conducted on artificial joints with triangular asperities and replicas of a real rock asperity surface under constant normal stiffness (CNS) conditions. The model was calibrated and then validated using selected data sets from the experimental results. Model simulations were found to be in good agreement with the rock joints behaviour under cyclic loading and CNS conditions both in stress prediction and dilation behaviour. In addition, dynamic stability analysis of an underground structure was carried out, using Universal Distinct Element Code and the proposed constitutive model. 相似文献
9.
循环剪切荷载作用下含二阶起伏体模拟岩石节理力学特性研究 总被引：1，自引：0，他引：1
利用人工材料浇注含二阶起伏体的模拟岩石节理试样,进行常法向荷载循环剪切试验,研究节理剪切力学特性在循环剪切过程中的劣化规律。试验结果表明：二阶起伏体对节理循环剪切力学特性有重要影响,剪切强度、剪切刚度、剪胀角随剪切循环次数增大而衰减,衰减趋势随着二阶起伏度的增大而加快;法向应力、二阶起伏度较大时,二阶起伏体对剪切力学特性的影响主要体现在第1轮剪切循环中,在随后的剪切循环中影响不明显;法向应力、二阶起伏度较小时,二阶起伏体的影响在前几轮循环剪切过程中均有较清晰的体现。基于Hertz接触力学理论,提出了节理面微凸体球面接触细观模型,揭示了节理循环剪切宏观试验现象的力学机制 相似文献
10.
A new experimental system composed of two devices is presented for studying the hydraulic conductivity of rock joints and other interfaces in relation with their mechanical loading. This system allows for investigations on the anisotropy of the hydraulic conductivity, as well as for its heterogeneity. The first device controls the injection of a fluid, regulated in pressure or discharge near the centre of the sample of rock joint, which produces a quasi‐radial flow within the joint. The output flow is measured in real time using a sectorized peripheral membrane for acquisition of data about the directionality or anisotropy of the flow. The second device allows for the measurement of the evolution of the morphology and of the void map of the rock joints during their mechanical loading (compression or shearing). It is a laser beam moved by an (x, y) frame. This frame is installed within the shear box at several stages of the loading, after temporarily moving one rock wall away from the other one, but without unmounting them from the shear box. After the presentation of the experimental system, and of its performances, we give some examples of test results of replicas of rock joints, loaded in compression and shearing. First, these results show that the change in global transmissivity of the samples is strongly correlated with the normal relative displacement of the rock walls. Several statistical analyses of the change in the void map, taking into account the damage of the asperities of the joint, are presented and compared with the results of the directional output flows. Today further studies involving a FEM as well as a finite volume modelling of the flow within the joints, based on the measured void map are in progress for a more precise comparison to the experimental results. Copyright © 2003 John Wiley & Sons, Ltd. 相似文献
11.
The dynamic shear behavior of rock joints is significant to both rock engineering and earthquake dynamics. With the discrete element method (DEM), the dynamic direct-shear tests on the rough rock joints with 3D (sinusoidal or random) surface morphologies are simulated and discussed. Evolution of the friction coefficient with the slip displacement shows that the 3D DEM joint model can accurately reproduce the initial strengthening, slip-weakening, and steady-sliding responses of real rock joints. Energy analyses show that the strengthening and weakening behavior of the rock joint are mainly attributed to the rapid accumulation and release of the elastic energy in the joint. Then, effects of the surface roughness and the normal stress on the friction coefficient and the micro shear deformation mechanisms, mainly volume change and asperity damage, of the rock joint are investigated. The results show that the peak friction coefficient increases logarithmically with the increasing surface roughness, but decreases exponentially with the increasing normal stress. In addition, the rougher rock joint exhibits both higher joint dilation and asperity degradation. However, high normal stress constrains the joint dilation, but promotes the degree of asperity degradation significantly. Lastly, the effects of the 3D surface morphology on the shear behavior of the rock joint are investigated with a directional roughness parameter. It is observed that the anisotropy of the surface roughness consequently results in the variation of the peak friction coefficient of the joint corresponding to different shearing directions as well as the micro shear deformation mechanisms, e.g., the extent of joint dilation. 相似文献
12.
不同充填度岩石分形节理抗剪强度的数值模拟 总被引：1，自引：0，他引：1
在对岩石节理进行分形模拟的基础上,建立了岩石分形充填节理直剪试验数值分析模型,采用数值模拟方法,研究了充填度与岩石分形充填节理抗剪强度之间的关系。结果表明,随着充填度的增大,分形节理抗剪强度总体上呈非线性减小。当充填度小于1时,随着充填度的增大,分形节理抗剪强度迅速减小,节理抗剪强度受节理表面形态、充填物力学性质以及壁岩力学性质的共同影响;当充填度大于1时,节理抗剪强度主要受充填物力学性质的控制,强度参数接近于节理充填物的强度参数。 相似文献
13.
节理在固定法向压力刚度（CNS）条件下的剪切过程比较复杂,剪切中由于剪胀的存在使得法向压力增大,而法向压力的增加又限制了剪胀的发生。根据CNS剪切过程中某一瞬时状态下法向压应力大小,以节理在该法向压应力下法向剪胀位移与剪切位移的关系为基础,建立一个楔形物理模型。通过循环迭代求得CNS剪切过程中每一步的法向压应力值,进而得到整个过程的剪切应力值。通过该模型,讨论了节理各参数对CNS剪切过程的影响,结果表明,其剪切应力值受法向压应力刚度与节理法向变形参数共同协调控制（包括单轴压缩变形及剪胀角的磨损）,节理在剪切过程中越不易发生压缩变形,其剪切应力值越大。 相似文献
14.
节理岩体几何结构非常复杂,研究其渗流特性对于指导含水岩层稳定性分析具有重要价值。应用离散裂隙网络模型DFN方法,基于VC++6.0软件平台,建立了平面渗流分析方法,分析了节理岩体不同几何分布情况下的渗透率张量特征,通过定义渗流定向性系数对岩体渗流的定向性特征进行了定量分析。结果表明：单组节理岩体渗流具有明显的各向异性特征,渗流定向性随着节理角度变化显著;节理随着节理贯通性增加,节理渗透率呈现对数增加趋势;两组节理情况下,各向异性特征随着节理组间夹角变化;两组节理岩体渗流特征研究中,正交分布下,岩体仍存在各向异性,但渗流定向性系数较低;当节理倾角服从正态分布时,随着节理倾角标准差增大,渗透率增加;两组节理夹角不同时,节理渗透主方向倾角随着夹角增大而相应增大,基本沿两组节理夹角方向的角平分线方向。 相似文献
15.
相同形貌结构面重复性剪切试验和各向异性剪切试验一直是岩体结构面剪切力学特性试验研究中的难点,而该问题对于工程岩体的开挖力学响应和稳定性分析、评价与控制至关重要,问题的关键在于同一种岩石的结构面形貌的再现。为此,基于3D扫描和3D雕刻技术,重复制备了3种不同粗糙度的大理岩结构面试样,开展了不同法向应力下相同形貌结构面的各向异性剪切试验。试验结果发现：（1）同一法向应力、不同剪切方向下,相同形貌结构面的剪切强度、剪胀和剪切破坏特征均呈现明显各向异性;（2）结构面粗糙度各向异性很大程度上决定了剪切强度的各向异性,两者具有较好的正相关性;（3）随着法向应力的升高,结构面剪切特征的各向异性有逐渐弱化的趋势。同时,研究还充分表明,3D雕刻技术是系统开展结构面剪切力学特征各向异性研究的可靠手段,可在将来研究中发挥更为重要的作用。 相似文献
16.
17.
岩体结构面力学行为的尺寸效应研究 总被引：1，自引：0，他引：1
尺寸效应是岩体结构面力学行为的重要特征。本文列举了结构面力学行为中普遍存在的尺寸效应现象,并由实测统计资料的分析,论证了结构面力学行为的尺寸效应具有分形结构。通过结构面力学行为尺寸效应的机理研究,建立了结构面力学行为尺寸效应分维数和结构面粗糙度系数尺寸效应分维数之间的相关关系,从而简化了结构面力学行为尺寸效应规律的表述,为客观评价岩体结构面力学参数提供最为有效的手段。 相似文献
18.
基于三维扫描与打印的岩体自然结构面试样制作方法与剪切试验验证 总被引：1，自引：0，他引：1
无法大量制作表面形态完全一致的含自然结构面的剪切试样一直是困扰岩石结构面力学试验深入研究的难题之一。借助最新发展的3D打印和表面快速扫描技术,提出了岩石自然结构面试样制作新方法。该方法采用三维扫描仪获得岩石自然结构面表面形态的高精度点云数据,然后通过逆向工程软件重构自然结构面的表面形态和含自然结构面的虚拟剪切模型,进而通过3D打印技术制作含自然结构面的PLA（绿色环保材料聚乳酸）塑材模具,最后借助PLA结构面模具在制样盒内通过相似材料浇筑成型出剪切试样,从而实现批量制作结构面形貌完全一致的相似材料结构面剪切试样,满足多种组合试样方案下岩石自然结构面的深入分析。采用这一方法针对3种岩石自然结构面进行了批量制作和剪切试验测试表明：（1）浇筑制作成试样的结构面表面高程与原始结构面高程之间的误差分析显示,岩石自然结构面可以高精度地复制到剪切试样中;（2）相同剪切试验条件下多个剪切试样的剪切位移-剪切力曲线的重合度非常高,表明制作的结构面剪切样的一致性好且试验结果离散性小;（3）通过剪切结构面试样在剪切前后的表面形态扫描分析发现,相同试验条件下自然结构面的剪切破坏形态具有非均匀性。 相似文献
19.
This paper presents a review of recent developments made by the authors into the modelling of rock joints in direct shear. Careful observation of laboratory direct shear testing on concrete/rock joints containing two-dimensional roughness has allowed theoretical models of behaviour to be developed. The processes modelled include asperity sliding, asperity shearing, post-peak behaviour, asperity deformation and distribution of stresses on the joint interface. Model predictions compare extremely well with laboratory test results. These models were then applied to direct shear tests on rock/rock joints, and although behaviour in general was well predicted, the strength of rock/rock joints was over-predicted. Direct shear tests have also been carried out on samples containing both two- and three-dimensional roughness to test the accuracy of the two-dimensional approximation to roughness adopted in the theoretical models. 相似文献
20.
Strength and dilatancy of jointed rocks with granular fill 总被引：1，自引：1，他引：0
Ashutosh Trivedi 《Acta Geotechnica》2010,5(1):15-31
It is well recognised that the strength of rock masses depends upon the strain history, extent of discontinuities, orientation
of plane of weakness, condition of joints, fill material in closely packed joints and extent of confinement. Several solutions
are available for strength of jointed rock mass with a set of discontinuities. There is a great multiplicity in the proposed
relationships for the strength of jointed rocks. In the present study, the author conceives the effect of increasing stresses
to induce permanent strains. This permanent strain appears as micro crack, macro crack and fracture. A fully developed network
of permanent deformations forms joint. The joint may contain deposits of hydraulic and hydrothermal origin commonly known
as gouge. The joint factor numerically captures varied engineering possibilities of joints in a rock mass. The joints grow
as an effect of loading. The growth of the joints is progressive in nature. It increases the joint factor, which modifies
the failure stresses. The dilatancy explains the progressive failure of granular media. Hence, a mutual relationship conjoins
effectively the strength of jointed rock and a dilatancy-dependent parameter known as relative dilatancy. This study provides
a simple and integral solution for strength of jointed rocks, interpreted in relation to the commonly used soil, and rock
parameters, used for a realistic design of structure on rock masses. It has scope for prediction of an equivalent strength
for tri-axial and plane strain conditions for unconfined and confined rock masses using a simple technique. 相似文献