共查询到15条相似文献，搜索用时 171 毫秒
1.
土木工程结构鲁棒控制的发展 总被引：1，自引：0，他引：1
评述了结构控制的发展,指出发展结构鲁棒控制策略的重要性。重点评述了结构双重调谐质量阻尼器(DTMD)和多重双重调谐质量阻尼器(MDTMD)的控制策略,提出了需进一步发展主动双重调谐质量阻尼器(ADTMD)和主动多重双重调谐质量阻尼器(AMDTMD)控制策略、此外,评述了结构鲁棒控制的设计准则与高层建筑和大跨桥梁在风与地震作用下的统一自适应主动鲁棒控制策略。 相似文献
2.
李春祥 《地震工程与工程振动》2005,25(5):169-176
提出了双层多重调谐质量阻尼器（DMTMD）和多重双重调谐质量阻尼器（MDTMD）控制策略。利用定义的优化目标函数,评价了最易制作DMTMD和MDTMD模型的性能。数值结果表明,DMTMD和MDTMD比基于任意整数或基于奇数的多重调谐质量阻尼器（AI-MTMD和ON-MTMD）具有更好的有效性和鲁棒性。MDTMD和DMTMD具有近似相同的有效性,但MDTMD比DMTMD具有更好的鲁棒性。总的来说,MDTMD的冲程大于DMTMD的冲程;DMTMD中小质量块的冲程大于AI-MTMD和ON-MTMD的冲程。 相似文献
3.
结构双层多重调谐质量阻尼器(DMTMD)控制策略的鲁棒性评价 总被引：1，自引：0，他引：1
基于定义的二类优化目标函数,评价双层多重调谐质量阻尼器(DMTMD)控制策略对漂移频率系数(DFR)摄动的鲁棒性。数值研究表明,使用第二类优化准则设计的DMTMD、双重调谐质量阻尼器(DTMD)和多重调谐质量阻尼器(MTMD)比使用第一类优化准则设计的DMTMD、DTMD和MTMD具有更高的对DFR摄动的鲁棒性。而且,使用第二类优化准则设计的总数为4的DMTMD、DTMD和总数为11的MTMD具有近似相同的对DFR摄动的鲁棒性。 相似文献
4.
土木工程结构的双层多重调谐质量阻尼器控制策略 总被引：4，自引：0，他引：4
李春祥 《地震工程与工程振动》2005,25(1):113-119
为能得到用尽可能少的调谐质量阻尼器(TMD)组成有效性和鲁棒性高的多重调谐质量阻尼器控制系统，本文提出了一种适用于土木工程结构的新控制策略——双层多重调谐质量阻尼器(DMT—MD)。使用定义的优化目标函数，评价了双层多重调谐质量阻尼器(DMTMD)的控制性能。数值结果表明，双层多重调谐质量阻尼器(DMTMD)比多重凋谐质量阻尼器(MTMD)具有更好的有效性和对频率调谐的鲁棒性。DMTMD比双重调谐质量阻尼器(DTMD)具有更好的有效性，而DMTMD和DT—MD对频率调谐的鲁棒性近似相同。因此，双层多重调谐质量阻尼器是一种先进的结构控制策略。 相似文献
5.
基于Maxwell型阻尼器的多重调谐质量阻尼器性能评价 总被引：1，自引：0，他引：1
李春祥 《地震工程与工程振动》2004,24(2):141-144
研究了基于Maxwell型阻尼器的多重调谐质量阻尼器(MTD—MTMD)在控制结构地震反应方面的最优动力特性。利用建立的设置MTD-MTMD时结构的传递函数,定义了设置MTD—MTMD时结构的动力放大系数(DMF)。将MTD-MTMD的优化准则定义为结构最大动力放大系数的最小值的最小化(Min．Min．Max．DMF)。利用定义的优化准则,评价了Maxwell型阻尼器的松弛时间系数(RTC)对MTD—MTMD最优参数和有效性的影响。利用最大的MTD—MTMD动力放大系数(DMF),评价了RTC对MTD-MTMD冲程的影响。 相似文献
6.
使用Kanai-Tajimi地震动模型,建立了主动调谐质量阻尼器(ATMD)结构系统的传递函数。将ATMD最优参数的评价准则定义为：设置ATMD结构均方根位移(解析式)的最小值的最小化。将ATMD有效性的评价准则定义为：设置ATMD结构均方根位移的最小值的最小化与未设置ATMD结构的均方根位移之比。根据逃择的评价准则,评价了地震卓越频率系数(EDFR)对ATMD抗震控制性能的影响。同时也评价了EDFR对被动调谐质量阻尼器(PTMD)抗震控制性能的影响。 相似文献
7.
李春祥 《地震工程与工程振动》2005,25(4):155-161
提出了适用于控制大跨桥梁风致振动的杠杆式主动多重调谐质量阻尼器（LT-AMTMD）控制策略.利用建立的LT-AMTMD结构系统的动力放大系数,评价了LT-AMTMD的性能.数值结果表明,驱动器置于质量块处的LT-AMTMD比驱动器置于其它位置的LT-AMTMD更加有效.驱动器置于质量块处的LT-AMTMD可以根据实际需要,通过改变支撑位置来调节弹簧的静伸长,而且保持其性能不变（包括冲程）.数值结果还表明,驱动器置于质量块处的LT-AMTMD可以明显地提高LT-MTMD的性能,而且比单个杠杆式主动调谐质量阻尼器（LT-ATMD）更加有效. 相似文献
8.
高柔结构在强风或地震等环境荷载作用下，往往会产生较大的变形和位移。采用调谐液体阻尼器对结构进行控制时，需要选择合适的水箱尺寸和水深，以期获得最好的减振效果。以往的调谐液体阻尼器参数优化往往基于等效线性模型或在小幅值激励下有较好精度的非线性浅水波动模型。采用了一种具有非线性阻尼和非线性刚度的等效调谐质量阻尼器模型对影响调谐液体阻尼器减振效率的主要参数进行了优化，该模型不再受小幅值激励的限制。优化结果表明，激励幅值对TLD的最优参数和减振效果有明显影响，同时水箱长度对TLD减振效果也有明显影响，这是基于线性模型TLD优化不能得到的结论。 相似文献
9.
以一座矮塔斜拉桥为研究对象,分析碰撞调谐质量阻尼器对于该结构的抑震效果。首先介绍了新型碰撞调谐质量阻尼器（Pounding Tuned Mass Damper,PTMD）的减震机理及基于接触单元的非线性碰撞力模型;之后,通过ANSYS软件中的APDL语言实现了PTMD减震系统的时域分析方法,并通过三条实际地震记录验证了PTMD的抑震效果。数值分析结果表明:（1）传统调谐质量阻尼器（tuned mass damper,TMD）及新型PTMD对于矮塔斜拉桥的位移、加速度及塔身弯矩响应均有较好的抑制效果;（2）PTMD相比传统TMD多了一种碰撞耗能模式,其减震效果略高于传统TMD。 相似文献
10.
本文研究了土-结构动力相互作用对采取不同控制措施的结构控制效果的影响。文中首先建立了主动调谐质量阻尼器(ATMD)、半主动磁流变阻尼器(MR)和被动多重调谐质量阻尼器(MTMD)等三种结构控制措施在时域中的控制算法和控制律，然后基于子结构法，采用间接边界元方法，通过傅里叶变换，推导了分别安装三种结构控制措施的受控结构在频域中的运动方程，数值仿真分析了某36层高层建筑的地震反应及其控制效果。结果表明，当采用ATMD或MTMD控制时，考虑土-结构动力相互作用后结构地震反应有所减小；当采用MR控制时，考虑土-结构动力相互作用后结构地震反应有很大程度的减小。由此看来，在设计软土地基上高层结构的结构控制措施时，不考虑土-结构动力相互作用对结构控制效果的影响是偏于安全的。 相似文献
11.
Design parameters for single- and multiple-tuned liquid column dampers for reducing the response of structures to seismic excitations are presented. A deterministic analysis is carried out using 72 earthquake ground motion records to determine the tuning ratio, tube width to liquid length ratio, and head loss coefficient corresponding to a given mass ratio for single-tuned liquid column dampers. A similar analysis is performed to determine the central tuning ratio, tuning bandwidth, and grouping of dampers for multiple-tuned liquid column dampers. The study indicates that by properly selecting the design parameters, single- and multiple-tuned liquid column dampers can reduce the response of structures to seismic excitation by up to 45 per cent. Design examples using single- and multiple-tuned liquid column dampers in a bridge and a ten-storey building are presented to illustrate how the parameters are selected and to demonstrate the performance of the devices under different ground excitations. The response of several structures with tuned liquid column dampers is compared with that using tuned mass dampers where it is shown that both devices result in comparable reductions in the response. © 1998 John Wiley & Sons, Ltd. This paper was produced under the auspices of the U.S. Government and it is therefore not subject to copyright in the U.S. 相似文献
12.
Active multiple tuned mass dampers （referred to as AMTMD）, which consist of several active tuned mass dampers （ATMDs） with identical stiffness and damping coefficients but varying mass and control force, have recently been proposed to suppress undesirable oscillations of structures under ground acceleration. It has been shown that the AMTMD can remarkably improve the performance of multiple tuned mass dampers （MTMDs） and is also more effective in reducing structure oscillation than single ATMDs. Notwithstanding this, good performance of AMTMD （including a single ATMD illustrated from frequency-domain analysis） may not necessarily translate into a good seismic reduction behavior in the time-domain. To investigate these phenomena, a three-story steel structure model controlled by AMTMD with three ATMDs was implemented in SIMULINK and subjected to several historical earthquakes. Likewise, the structure under consideration was assumed to have uncertainty of stiffness, such as 4-15% of its initial stiffness, in the numerical simulations. The optimum design parameters of the AMTMD were obtained in the frequency-domain by implementing the minimization of the minimum values of the maximum dynamic magnification factors （DMF） of general structures with AMTMD. For comparison purposes, response analysis of the same structure with a single ATMD was also performed. The numerical analysis and comparison show that the AMTMD generally renders better effectiveness when compared with a single ATMD for structures subjected to historical earthquakes. In particular, the AMTMD can improve the effectiveness of a single ATMD for a structure with an uncertainty of stiffness of 4-15% of its initial stiffness. 相似文献
13.
Tuned mass dampers for response control of torsional buildings 总被引：1，自引：0，他引：1
This paper presents an approach for optimum design of tuned mass dampers for response control of torsional building systems subjected to bi‐directional seismic inputs. Four dampers with fourteen distinct design parameters, installed in pairs along two orthogonal directions, are optimally designed. A genetic algorithm is used to search for the optimum parameter values for the four dampers. This approach is quite versatile as it can be used with different design criteria and definitions of seismic inputs. It usually provides a globally optimum solution. Several optimal design criteria, expressed in terms of performance functions that depend on the structural response, are used. Several sets of numerical results for a torsional system excited by random and response spectrum models of seismic inputs are presented to show the effectiveness of the optimum designs in reducing the system response. Copyright © 2002 John Wiley & Sons, Ltd. 相似文献
14.
非对称结构扭转振动多重调谐质量阻尼器(MTMD)控制的最优位置 总被引：1，自引：1，他引：1
研究了非对称结构扭转振动多重调谐质量阻尼器(MTMD)控制的最优位置。本文采用的MTMD具有相同的刚度、阻尼，但质量不同。基于导出的设置MTMD时非对称结构扭转角位移传递函数，建立了扭转角位移动力放大系数解析式。MTMD最优参数的评价准则定义为：非对称结构最大扭转角位移动力放大系数的最小值的最小化。MTMD的有效性评价准则定义为：非对称结构最大扭转角位移动力放大系数的最小值的最小化与未设置MTMD时非对称结构最大扭转角位移动力放大系数的比值。基于定义的评价准则，研究了非对称结构的标准化偏心系数(NER)和扭转对侧向频率比(TTFR)对不同位置MTMD最优参数和有效性的影响。 相似文献
15.
Julio C. Miranda 《地震工程与结构动力学》2005,34(7):847-865
This paper presents an energy‐based theoretical model for a two degree‐of‐freedom mechanical system. After a general formulation in Appendix A, the model is specialized to study tuned mass dampers as a means to substantially increase modal damping in order to induce a consequential decrease of the seismic response of the structures thus provided. Although approximate since it neglects coupling due to damping, it is shown that the model yields a first‐order approximation to the exact frequencies, providing values of optimum damping that closely match exact results proposed by others. In view of this, it is proposed that the model be applied through an iterative numerical procedure that identifies the pertinent optimum parameters. It is also shown that for certain particular benchmark cases the model provides closed‐form equations for the parameters defining the dynamic states related to these special conditions. Despite its approximate nature the model presented in this paper is rational, and due to its explicit consideration of energy balance and overall simplicity, it provides a convenient platform for the study of tuned mass dampers, as well as for other methods of structural passive control. Copyright © 2005 John Wiley & Sons, Ltd. 相似文献