共查询到20条相似文献，搜索用时 406 毫秒
1.
G.-G. Yea 《Marine Georesources & Geotechnology》2013,31(1):76-90
The behaviors of the marine sedimentary ground improved by sand compaction pile (SCP) method are analyzed. To do this, the results of upheaval characteristics of the sea floor, undrained shear strength, and horizontal consolidation coefficient (consolidation) are investigated. Due to SCP installation on ground, as thickness of a soft clay layer increases, upheaval height increases and upheaval angle decreases. Undrained shear strength of disturbed ground due to SCP construction decreases in early stage after completion of construction, but it shows a trend of recovering as months elapse. As the result of piezocone penetration dissipation tests, consolidation delay phenomenon by the disturbance due to SCP installation clearly is identified and its degree is dependent on the replacement area ratio of SCP and the location of ground. 相似文献
2.
In order to accurately design a sand compaction pile (SCP) with low replacement area ratio, it is important to understand the mechanical interaction between the sand pile and clay ground and its mechanism during consolidation process in composite ground. In this article, therefore, a series of numerical analyses on composite ground improved by SCP with low replacement area ratio were carried out. The applicability of numerical analyses, in which an elasto-viscoplastic consolidation finite element method was applied, were confirmed by comparing the results obtained from a series of laboratory model tests with the composite ground improved by SCP. Through the results of the numerical analyses, mechanical behavior of the sand pile and clay in composite ground during consolidation is elucidated, together with a stress sharing mechanism between sand pile and clay. 相似文献
3.
In order to accurately design a sand compaction pile (SCP) with low replacement area ratio, it is important to understand the mechanical interaction between the sand pile and clay ground and its mechanism during consolidation process in composite ground. In this article, therefore, a series of numerical analyses on composite ground improved by SCP with low replacement area ratio were carried out. The applicability of numerical analyses, in which an elasto-viscoplastic consolidation finite element method was applied, were confirmed by comparing the results obtained from a series of laboratory model tests with the composite ground improved by SCP. Through the results of the numerical analyses, mechanical behavior of the sand pile and clay in composite ground during consolidation is elucidated, together with a stress sharing mechanism between sand pile and clay. 相似文献
4.
The use of sand compaction pile or gravel compaction pile is nowadays a common approach for soft ground improvement. In this article, a recycled aggregate porous concrete pile has been developed by replacing natural aggregates with recycled aggregates to overcome issues related to bulging failure or reduced section geometries. Such issues may arise during installation and during the early stages of operation. In addition, the proposed approach utilizes recycled aggregates instead of natural materials. To investigate the applicability of the recycled aggregate porous concrete pile method as a ground improvement technique, a series of laboratory model consolidation tests was performed on soft clay soil reinforced with sand compaction pile, gravel compaction pile, and recycled aggregate porous concrete pile, respectively. The results indicated that the settlement reduction effect of recycled aggregate porous concrete pile was significantly higher than the sand compaction pile and gravel compaction pile methods. The stress sharing ratio from the experimental program showed good agreement with those calculated by elasticity theory. Comparative analyses of the recycled aggregate porous concrete pile versus sand compaction pile and gravel compaction pile approaches, under the same replacement area ratio and surcharge pressure, showed significantly improved consolidation time, settlement reduction, and stress sharing effect. 相似文献
5.
Je Sung Jeon 《Marine Georesources & Geotechnology》2016,34(1):33-41
A very soft ground constructed by dredging and hydraulic fill has characteristics such as high water content, high initial void ratio, and very little effective stress. Estimating, with thorough considerations about consolidation properties and the initial stress associated with each layer's distinctive stress history, is essential in order to predict a reasonable consolidation settlement of soft ground. By investigating a construction project for national industrial complexes at a coastal area in southern Korea that experienced reclamation and ground improvement adapting PVD, various laboratory tests to find consolidation properties were performed with undisturbed samples collected from the entire depth of the marine clay fill layer and original clay layer. Through the investigation, this report suggests relationships of heterogeneity of permeability in both vertical and horizontal directions, void ratio-effective stress, and void ratio-permeability. Considering the fact that the original clay layer was under the process of consolidation by load due to hydraulic fill from the top, estimating the appropriate initial stress of each layer is critical to predict the future process of consolidation settlement determined by time. In order to obtain the initial stresses of two layers with different stress histories related to consolidation, cone penetration and dissipation tests were conducted. 相似文献
6.
Until now more than 14 subway lines are in operation and some new lines are being built in the coastal city Shanghai. The longitudinal settlement of shield tunnel has significant effect on the safety of the subway operation. In this paper, the deformation of the shield tunnel and the surrounding soil were analyzed by the establishment of a three-dimensional model. The vertical displacements of four paths (Path 1 is on the ground; Path 2 is at the top of the tunnel; Path 3 is in the middle of the tunnel; Path 4 is at the bottom of the tunnel) are affected by the nature of the soil. The horizontal displacement is smaller than the vertical displacement and horizontal displacement of the clay is larger than that of the sand. The distribution of the pore pressure changes with soil properties around the tunnel. The pore pressure of the sand layer is larger than that of the clay layer at the same depth of underlying soil. 相似文献
7.
Gang Zheng Jingjin Liu M. S. Rahman Zaikun Tan 《Marine Georesources & Geotechnology》2017,35(5):631-642
This paper describes a full-scale test on a very soft clay ground around 70,000?m2, which is conducted in Huizhou of Guangdong Province, China, to present a new method of vacuum preloading method. A novel moisture separator was developed, which can automatically regulate the vacuum pressure variation by changing the volume of the gas inside it. A large quantity of water drained by the proposed moisture separators can be directly used as a surcharge loading, which would shorten the ground improvement time and save costs as well. Three levels of silt-prevention prefabricated vertical drains were used in the treating process to accelerate the consolidation. In addition, the vacuum preloading method also included an effective radial drainage device which would strengthen the dredged soft clay fill in a deep layer. In the in situ test, tens of piezometers and settlement plates were installed to measure the variations of excess pore water pressures and settlement of two stages of observation points at different positions in the ground. The results show that the largest average consolidation settlement was 314.1?cm and made a saving of more than 66% in power consumption compared with traditional method. It demonstrates that this adopted method is an efficient, cost-effective, and environmentally friendly method for improving sites with low bearing capacity and high compressibility soils. 相似文献
8.
Consolidation occurs in estuarine marine clays for coastal reclamation by dissipation of the excess pore pressure, which is induced by increasing the total overburden stress during conventional mechanical surcharging. The excess pore pressure can be decreased usually by the use of several construction methods such as sand drain and paper drain. Besides the drain methods, vacuum can also be used in the soil mass to consolidate the estuarine marine clays by decreasing the pore pressure as well as increasing the effective stress.The study on vacuum consolidation is devoted so far mainly for laboratory model tests or numerical analysis in Korea. Recently, an instrumentation system was applied to manage the vacuum-applied consolidation on a field, in which a sewage disposal plant was constructed. While vacuum was applied, the behaviors of estuarine marine clays such as the settlement, lateral deformation and pore water pressure have been investigated precisely. The behavior of estuarine marine clays during vacuum-applied consolidation shows some difference from the behavior of estuarine marine clays in the case of conventional preloading. A principal difference is that the lateral deformation corresponding to settlement is smaller than before vacuum application even though the surcharge height has been increased. 相似文献
9.
Hongyue Sun Gang Wu Xin Yan Dongfei Wang Zhenlei Wei 《Marine Georesources & Geotechnology》2018,36(8):940-949
Conventional drainage consolidation methods cause significant energy consumption and environmental issues. In this paper, a method combining siphon drainage and surcharge loading is proposed to drain water from soft soil with vertically installed prefabricated vertical drains (PVDs) and a siphon tube. To investigate the availability and effectiveness of this method, a laboratory physical modeling test was conducted to investigate the drainage and consolidation behavior. The laboratory modeling test results of this method were compared with the calculated results of the ideal sand-drained ground consolidation method to clarify the advantages and mechanism of this method. Comparison results show that the pore pressure and settlement in the proposed method developed faster than the calculation results of ideal sand-drained consolidation theory. About 10?m thickness of unsaturated zone can be formed by siphon drainage which produce a surcharge loading effect on the soil below the flow profile. Drainage is a very slow process in soft soil, and siphon drainage can work continually. Siphon drainage combined with surcharge loading is potentially a good alternative to drain water from soft clay economically and environmentally. 相似文献
10.
Nansha clay is an interactive marine and terrestrial deposited soft clay that is widely spread in Guangzhou, Pearl River Delta, China. To avoid excessive settlement after construction, there is a need for better quantifying the time-dependent deformation of the soft clay. This paper presents a preliminary study to predict the one-dimensional compression of Nansha clay using fractional derivatives. A fractional Merchant model was introduced to describe the time-dependent settlement, and analytical solutions were obtained in terms of the Mittag-Leffler function. The oedometer test results were presented to validate this model. Compared with classical rheological models, the fractional derivative-based model enabled close estimation of the one-dimensional compression with fewer parameters. The meaning of the order of fractional derivative and its relationship with the clay physical properties were explored. It shows that a smaller value of this order corresponded to a higher coefficient of consolidation and a lower coefficient of secondary consolidation. The amplitude of both the primary and secondary consolidation of clay may be estimated quantitatively by the order of fractional derivative. Taken together, these results may open up new avenues for theoretical and empirical modeling of rheological phenomena in clay using fractional derivatives. 相似文献
11.
12.
Considering the characteristics of seabed ground in coastal reclamation area, ultra soft clay improvement method by heavy tamping after rockfilling displacement was proposed combined with a case study. The improvement mechanisms of the method can primarily be attributed to rockfilling displacement (RD), dynamic compaction (DC), dynamic replacement (DR) and dynamic replacement and mixing (DRM). For the case study given in this article, heavy tamping construction program was proposed based on field pilot tests. Furthermore, the effectiveness of the proposed ground improvement method was verified through in situ plate load test, sand fill test and the analyses of observed settlement data. Thus, the method of heavy tamping after rockfilling displacement is applicable for the improvement of seabed ground in coastal reclamation area. It is proposed for similar projects that heavy tamping of fills may be performed by layers and correspondingly tamping energy increased to further enhance the improvement effect of DC, DR and DRM. In addition, delayed improvement effect or time effect of soil mass after heavy tamping is still an issue to be further studied. 相似文献
13.
Pengpeng Ni 《Marine Georesources & Geotechnology》2013,31(6):671-682
AbstractFor land reclamation using the conventional surcharge preloading method, a sand cap layer is often fully placed at the ground surface of ultra-soft compressible estuary or marine clays. A novel strategy of distributed sand caps is proposed to save cost associated with sand materials. At an early stage of consolidation, the drainage capacity of distributed sand caps is less than the drainage demand, whereas at a later stage, the capacity exceeds the demand. Hence, the overall drainage capacity of distributed sand caps is equivalent to the drainage demand. A numerical model is developed to study the effectiveness of the proposed technique, and calculations are compared against theoretical solutions. A parametric study is conducted to optimize design parameters. It has been found that distributed sand caps should be uniformly placed with a size of 3% of the total width and a spacing of 1 times the size, such that sand materials can be saved by up to 50% without compromising the consolidation efficiency (an increase of consolidation time by less than 5%). The use of distributed sand caps will be effective regardless of soil properties, including hydraulic conductivity, elastic modulus and Poisson’s ratio. 相似文献
14.
The behavior of single piles subjected to negative skin friction in soft soil was conducted by analyzing the results from full-scale long-term field measurements and three-dimensional (3D) numerical analyses. A skin friction coefficient (α and β coefficients) of the instrumented piles is back-calculated at different degrees of consolidation (U) of soft marine clay. Back-calculated β-values ranged from 0.15 to 0.35 for clay, and from 0.30 to 0.55 for sand, respectively. In addition, back-calculated α-values ranged from 0.1 to 0.3 for coated pile, and from 0.2 to 0.8 for uncoated pile when undrained shear strength of the soft clay was about 30–60 kPa, respectively. Moreover, this study describes behavior of a pile based on full-coupled 3D finite element (FE) analysis. The appropriate parametric studies needed for verifying the pile-soil interaction with consolidation are presented in this paper. Compared to the results from the measurements, it is shown that the computed results are capable of predicting the pile-soil behavior under consolidation. The major parameters that influence the pile behavior are discussed for different soil-pile conditions. 相似文献
15.
Quantitative laboratory studies on the structural behavior of natural intact marine clays require a large number of identical natural samples leading to an expensive and challenging task. This study proposes a simple method to reconstruct an artificial structured marine clay as the state of its natural intact clay at both macro and micro levels. For this purpose, the Shanghai marine clay is selected and mixed with low cement contents (1–6%). The clay-cement slurry is mixed in a container with the ice-covered sides at a low temperature about 0 ± 2 °C to postpone the hydration reactions until consolidation began. The purpose of adding cement is to generate the inter-particle bonding and structure in reconstituted samples. Initially, the reconstituted samples are consolidated under the in situ stress of 98 kPa and then under the pre-consolidation pressure of 50 kPa. Mechanical characteristics such as compression index, yield stress, unconfined compression strength, shear strength ratio, and the stress paths from triaxial tests are compared with natural intact clay accordingly. Scanning electron microscope and mercury intrusion porosimetry analyses are also performed to analyze the microstructure of clays for comparison. Furthermore, the proposed method is also examined by using natural intact marine clays of different locations and characteristics. 相似文献
16.
The results of one-dimensional compression tests conducted on undisturbed specimens of Jiangsu soft marine clay is presented. Because of its high in situ void ratios and natural water content, Jiangsu soft marine clay displays high values of both the virgin compression index, Cc, and the secondary compression coefficient, Cα. The laboratory data indicates that the value of the ratio Cα/Cc for Jiangsu soft marine clay is constant. However, neither Cα nor Cc are constant: they both depend upon the natural water content (or void ratio) and thus are also dependent on the deformation (or compression) of Jiangsu soft marine clay. Settlement analyses show that the secondary settlement of Jiangsu soft marine clay is a significant component of the field settlement. The concept of a constant value for Cα/Cc is used to predict the secondary settlement of a surcharged embankment founded upon Jiangsu soft marine clay. The predictions are in agreement with the limited post-construction field measurements of the embankment settlement. 相似文献
17.
1 .IntroductionTheZhapuPortissituatedonthenorthbankoftheHangzhouBay ,nearZhapuTowninPinghuCity ,Zhejiangprovince .Asthefirststepofconstruction ,reclamationwasaccomplishedinthehinter landoftheharbor.Theborderdikeofafulllengthof 1 2 71mislocatedinthetidalregionoftheHangzhouBay .ThepreliminarydesignofthisprojectwascompletedinJune 1 986 ,anditsconstructionbeganinJuly 1 986 ,andwascompletedinMarch 1 991 .TheseadikewasbuiltontheQ4marinedepositofsaturatedsoftclaywithathicknessofabout2 7mandgeo… 相似文献
18.
Dongseop Lee Sangwoo Park Timothy D. Stark Younguk Kim 《Marine Georesources & Geotechnology》2013,31(4):348-359
Use of Terzaghi's one-dimensional consolidation theory is not suitable for consolidation of highly deformable soft clays such as dredged soils. To model this condition, it is necessary to consider non-linear finite strain consolidation behavior, i.e., changes in compressibility and permeability with increasing stress. A one-dimensional non-linear finite strain numerical model, Primary Consolidation, Secondary Compression, and Desiccation of Dredged Fill (PSDDF), has been used to predict the stress-dependent settlement of fine-grained dredged materials. In this paper, two case studies of using PSDDF are discussed to illustrate the applicability and accuracy of PSDDF. The first case study involves PSDDF simulations of laboratory-phased placement of a marine clay dredged from Busan, Korea. PSDDF results are in good agreement with the corresponding results of the laboratory large strain consolidation tests. The other involves estimating the service life of the Craney Island Dredged Material Management Area near Norfolk, Virginia, in the United States. The excellent agreement between measured and calculated values shows that PSDDF is a reliable tool for predicting settlement of dredged material. 相似文献
19.
Zhang Dingwen Liu Songyu Han Wenjun Du Guangyin 《Marine Georesources & Geotechnology》2013,31(4):332-347
A remarkable combined dry jet mixing (DJM) and prefabricated vertical drains (PVDs) method was used to enhance the performance for soft ground improvement. In the combined method, PVDs are first installed and then DJM columns are installed between the PVDs at larger spacing. This combined method improves the effectiveness of the ground improvement and creates a more economical solution. This paper presents a case study of the combined method for marine clay improvement in Lianyugang of China. The excess pore water pressure in soils created by the installation of DJM columns with and without PVDs was monitored and compared. In situ standard penetration tests were conducted in the DJM columns and before-and-after piezocone penetration tests were performed in soils surrounding the columns. Long-term settlement monitoring under embankment loading was carried out for the ground improved by combined method and DJM method alone. The field tests, settlement monitoring and economic benefit analysis results demonstrated that the DJM-PVD method is technologically sound and cost-effective as compared with the conventional DJM method. 相似文献
20.
Chun-Ming Lin Yan-Li Li Hong-Chun Zhuo George W. Shurr Jennie L. Ridgley Zhi-Ping Zhang Tao Xue 《Marine and Petroleum Geology》2010,27(4):909-922
Late Quaternary shallow biogenic gas reservoirs have been discovered and exploited in the Qiantang River (QR) estuary area, eastern China. The fall of global sea level during the Last Glacial Maximum resulted in the formation of the QR incised valley. From bottom to top, the incised valley successions can be grouped into four sedimentary facies: river channel facies, floodplain–estuarine facies, estuarine-shallow marine facies, and estuarine sand bar facies.All commercial biogenic gas pools occur in floodplain–estuarine sand bodies of the QR incised valley and its branches. The deeply incised valleys provided favorable conditions for the generation and accumulation of shallow biogenic gas.The clay beds that serve as the direct cap beds of the gas pools are mostly restricted within the QR incised valley, with burial depths ranging from 30 to 80 m, remnant thicknesses of 10–30 m, and porosities of 42.2–62.6%. In contrast, the mud beds cover the whole incised valley and occur as indirect cap beds, with burial depths varying from 5 to 35 m, thicknesses of 10–20 m, and porosities of 50.6–53.9%. The pore-water pressures of clay and mud beds are higher than that of sand bodies, and the difference can be as much as 0.48 MPa. The pore-water pressures of clay or mud beds can exceed the total pore-water pressure and gas pressure of underlying sand reservoirs. Shallow biogenic gas can be completely sealed by the clay and mud beds, which have higher pore-water pressure. The direct cap beds have better sealing ability than the indirect cap beds.Generally, the pore-water pressure dissipation time of clay and mud beds is conspicuously longer than that of sand beds. This indicates that the clay and mud beds have worse permeability and better sealing ability than the sand beds. However, once the gas enters the sand lenses, the pore-water pressure cannot release efficiently. 相似文献