共查询到17条相似文献，搜索用时 218 毫秒
1.
2.
3.
采用三维非线性有限单元法对牛牛混凝土面板堆石坝施工期和蓄水期的应力变形进行模拟计算,并结合沈珠江提出的指数型曲线流变模型,采用自行编制的有限元程序对大坝进行了三维流变分析,得到了坝体、面板在各个时期的应力和变形情况,以及堆石流变对坝体应力变形的影响;计算面板和周边缝位移时采用了三维子模型法,根据实际的坝体填筑、蓄水过程,对每一期面板浇筑之前的坝体上游面位移进行修正,并通过在面板与堆石体之间设置三维面-面摩擦接触单元,来有效模拟面板的应力、变形,为该坝的进一步优化设计提供了有益的建议。 相似文献
4.
隘口心墙堆石坝基岩岩溶发育,右岸分布有多个溶洞群,其中K6和K5的空腔体积均超过10万方.溶洞群不仅对右岸坝基防渗影响较大,而且由于K6溶洞位于右岸坝肩应力影响范围之内,对右岸坝肩压缩变形、坝体稳定性及心墙应力应变影响最为显著.本文采用了有限元法研究了K5溶洞处理前后坝体及基岩的渗流场特征,K6溶洞天然地基未换填、部分换填及完全换填三种工况下的的坝体及基岩的应力与变位.结果表明,由于K5溶洞离坝肩较远,对于K5溶洞对坝体应力应变影响较小,处理重点是做好防渗处理,而K6则对坝基变位和应力影响显著,需进行换填处理,从而显著减小右坝肩压缩变形,改善坝肩位移和应力分布协调性,同时消除沥青心墙右侧的拉应力区. 相似文献
5.
6.
为研究河谷地形对深厚覆盖层中防渗墙应力、变形的影响,以某沥青混凝土心墙堆石坝为工程背景,模拟了狭窄河谷和宽深河谷并分别建立有限元模型,坝体材料及覆盖层采用邓肯-张E-B模型,防渗墙与覆盖层、基岩之间的接触关系采用无厚度接触面模拟,进行三维非线性有限元计算,对比分析两种河谷情况下防渗墙的应力、变形情况。计算结果表明：狭窄河谷中,防渗墙沉降和水平向位移及防渗墙与覆盖层的不均匀变形均比宽深河谷小,其中不均匀变形最大减小了24.8%;宽深河谷中,防渗墙受河谷地形约束作用较弱,竖直向压应力较狭窄河谷更大,最大增加了40.3%;防渗墙的竖直向压应力最大值位置受中性点位置和河谷地形的共同影响,其中竖直向压应力最大值约30%来自墙顶坝体土压力,70%来自与覆盖层之间的负摩擦力。其研究结果可为不同地形条件下坝基防渗墙的设计提供参考。 相似文献
7.
采用三维有限元方法,研究了面板竖缝特性对面板堆石坝中面板应力变形的影响。基于类似子结构法概念,建立了精细模拟面板及其分缝特性的三维有限元分析方法。针对马来西亚巴贡面板堆石坝,计算了多种面板竖缝宽度和填料的方 案,得到坝体和面板的应力变形。计算结果表明,面板竖缝几何尺寸和填料特性对面板的挠度、顺坡向应力、水平向压应力和周边缝张合变形影响不大,而对面板的水平向拉应力和竖缝压缩量影响很大;面板竖缝填料变软和宽度增大均会导致面板的水平向压应力减小,而竖缝压缩量明显增大;采用软木作为填充材料较之填充硬木,可以大约降低一半的压应力;面板竖缝宽度及其填料特性对同期填筑的面板、特别是邻近的面板水平向压应力影响较大。 相似文献
8.
9.
结合实测资料和有限元方法分析建于深覆盖层地基上面板堆石坝的应力、变形特性。数值计算中采用邓肯-张E-B模型模拟覆盖层地基和坝体的应力、变形行为,同时采用无厚度接触面模拟面板和坝体以及防渗墙和地基之间的相互作用。整理和分析工程实测资料并与数值计算结果进行对比分析,重点分析坝体和防渗结构的力学行为以及面板堆石坝和地基之间的相互作用。比较分析表明,大坝最大沉降和压应力分别发生在坝体底部和覆盖层中,覆盖层对坝体及防渗结构的应力、变形特性具有显著影响,应力、变形实测值与数值计算结果吻合较好,说明数值计算结果的有效性。在此基础上,分析了覆盖层上面板堆石坝分期填筑和筑坝速度对坝体和防渗结构应力变形的影响。结果表明,分期填筑引起坝体较大不均匀沉降和复杂的应力状态,但一定程度上可以改善防渗墙的应力变形特性;较快的坝体填筑速度容易引起坝体较大的前期应力和后期沉降,不利坝体的施工和运行。 相似文献
10.
高混凝土面板堆石坝流变的三维有限元数值模拟 总被引：4，自引：0，他引：4
采用一种新的能模拟高围压条件的堆石料幂函数流变本构模型,对水布垭面板堆石坝进行了考虑堆石料流变特性的应力-应变仿真分析。结果表明,考虑堆石料流变特性后的坝体变形有明显的增加,坝体应力有所松弛。堆石体的流变特性使得面板的挠度有所增加,面板顺坡向和坝轴向拉应力极值有所增大。对于分期浇筑面板、分期蓄水的高混凝土面板堆石坝,选用合适的流变本构模型正确地模拟堆石体的流变特性,其结果可以为大坝填筑进度及面板分期浇筑时间的确定提供参考,对于正确地预测大坝的应力变形也具有重要意义。 相似文献
11.
流变变形对高面板堆石坝面板脱空的影响分析 总被引：8，自引：3，他引：5
面板堆石坝尤其是高面板堆石坝的运行实践表明,堆石的流变现象比较显著。采用基于直接约束算法的接触力学分析方法模拟了混凝土面板和堆石体之间的接触关系。考虑堆石体的流变特性,并结合天生桥一级面板堆石坝的现场观测结 果,对高面板堆石坝中的面板脱空问题进行了有限元计算分析,研究了坝体流变变形对面板脱空和垫层亏坡问题的影响。 相似文献
12.
13.
Three‐dimensional numerical analysis of concrete‐faced rockfill dam using dual‐mortar finite element method with mixed tangential contact constraints 
下载免费PDF全文
下载免费PDF全文 Concrete‐faced rockfill dam (CFRD) is a popular alternative to traditional dam types in the last two decades. The modelling of CFRD involves complex multi‐body contact and strong geometry and material nonlinearities. We present a numerical approach for the modelling of CFRDs in this paper. Based on the dual‐mortar finite element method, the presented approach considers different parts of rockfill and all concrete slabs as independent deformable continuum. The multi‐body contacts are modelled using Lagrange multipliers with a weak form segment‐to‐segment contact strategy. To alleviate instability induced by strong geometry nonlinearity in the slab–slab contact, we propose a mixed type of constraints for the tangential contact. A general transformation scheme is introduced to simplify the implementation of contact constraints. Three‐dimensional analysis of Tianshengqiao‐1 CFRD is performed. The nonlinear and time‐dependent deformation of the rockfill is considered. We study the influence of the rockfill deformation on the reliability of the concrete face. Three major concerns of the face, that is, the axial compression, the slab–slab separation and the face‐rockfill separation, are discussed in detail. The numerical results are compared with data from in‐situ observation. Copyright © 2016 John Wiley & Sons, Ltd. 相似文献
14.
贴坡型混凝土面板堆石坝三维非线性分析 总被引：2，自引：0，他引：2
利用堆石坝对地形条件适应性强的优势,将混凝土面板堆石坝设计建于条形山脊上,依天然坡面分别贴岩坡填筑堆石料,使原山体成为坝体一部分而形成的混凝土面板堆石坝,称之为贴坡型混凝土面板堆石坝。利用目前应用较为广泛的邓肯E-B模型,基于ABAQUS提供的2次开发用户子程序,对某贴坡型混凝土面板堆石坝施工填筑期和水库蓄水运行期的应力与变形进行模拟分析。计算结果表明,受地形和岩坡开挖形态的影响,贴坡型混凝土面板堆石坝的坝体变形规律与常规混凝土面板堆石坝有较大的不同,坝体沉降、水平位移以及面板的变形都较小;阶梯状的建基面凸角处有明显的应力集中,相应部位的应力水平较高。计算成果可为优化设计提供合理的建议和有效的措施。 相似文献
15.
With the long-term operation of the project, the material parameters of concrete-facing sand–gravel dam will change, which brings great difficulty to the scientific and effective stress and deformation analysis. Combining with the measured displacement data, the finite element analysis model of the concrete-facing sand–gravel dam of Heiquan reservoir was established, and the modulus of elasticity and internal friction angle of the dam body were inverted by the measured displacement of the dam, then the simulation analysis of the filling construction process and the reservoir storage process of dam was carried out, and the stress and deformation values of the dam during the construction period and the impoundment period were calculated. The results showed that the parameters obtained from the inversion are smaller than the original parameters, but there is little difference between them. The displacement calculated by finite element inversion was close to the measured displacement value, the overall displacement and stress distribution of the dam body and panel were in line with the general law, and the calculated displacement and stress values were at the normal level. This study provides a reference for parameter inversion and stress and deformation analysis of concrete slab dam through monitoring data analysis.
相似文献16.
心墙堆石坝的湿化变形已经为人们认识和重视,面板堆石坝由于上游有混凝土面板挡水,其湿化变形很少引起重视,但由湿化变形比较明显的堆石料填筑的坝体,在降雨过程中往往产生较大湿化变形,影响混凝土面板的工作性状。本文研究提出了大气降水引起堆石体达到一定饱和度情况下湿化变形的计算方法。进行了滩坑水电站混凝土面板堆石坝堆石料湿化变形试验,采用弹塑性平面有限单元法,分析研究了堆石料浸水湿化对坝体应力变形以及混凝土面板应力变形性状的影响。 相似文献
17.
Numerical evaluation of soft inter‐slab joint in concrete‐faced rockfill dam with dual mortar finite element method 下载免费PDF全文
下载免费PDF全文 Recently constructed concrete‐faced rockfill dams (CFRDs) often use soft inter‐slab joints to prevent axial compression‐induced extrusion damage in the concrete face. Due to the complexity of the multibody contact and the lack of information on the actual behavior of soft joints, it is highly challenging to numerically assess the effect of soft joints in CFRDs. In this paper, we present a numerical approach for the three‐dimensional modeling of CFRDs with hard and soft joints. A dual mortar finite element method with Lagrange multiplier is developed to treat the multibody contact in hard joints with impenetrability condition. The soft joint slab‐filler‐slab contact system is modeled using an equivalent contact interface approach, where the soft contact constraints are imposed using a perturbed Lagrange formulation. Through a series of laboratory tests, the mechanical behavior of soft joint is investigated. An extrusion model for the soft joint is presented and implemented in the dual mortar finite element method. The proposed numerical method is applied to the three‐dimensional analysis of Tianshengqiao‐1 CFRD. Despite the complex multibody contact and strong material and geometry nonlinearities in the CFRD, the proposed method is stable and capable of capturing salient characteristics of the CFRD. Numerical results show that in Tianshengqiao‐1, the employment of soft joints can effectively reduce the axial compression stress, thus greatly alleviating the risk of extrusion damage in the concrete face. 相似文献