共查询到18条相似文献，搜索用时 296 毫秒
1.
2.
时序雷达干涉图中的永久散射体(PS)可看作“天然GPS点”, 以构成网络用于监测长期的地表形变. 本文提出采用邻接矩阵拓扑模型对基于Delaunay剖分算法生成的PS网络进行基线识别, 并采用时序相干最大化算法求解PS基线的线性形变速度增量和高程误差增量. 该数据模型和计算方法被应用于探测香港地区2006~2007年间的区域地表沉降. 实验研究采用由Envisat卫星ASAR传感器对该地区成像所获取的时序SAR影像作为数据源, 并联合该地区12个GPS连续运行参考站的观测数据予以大气修正和地面控制. 实验结果表明, 该模型和方法应用于地表形变测量是有效的和可靠的, PS网络方法探测地面沉降的精度约为±2.0 mm/a. 相似文献
3.
4.
时序InSAR技术是近些年发展起来的一种新的InSAR测量技术.其中PS-InSAR技术是通过分析高相干的永久散射体相位变化信息提取形变,受时间和空间基线的限制小,该方法需要假设形变特征为匀速,同时需要大量的SAR数据（25景）来估算大气效应贡献值;短基线技术（SBAS）可以降低几何去相干的影响,同时较短基线使DEM误差的敏感性大大降低,但该方法通过一定大小的窗体计算相干性,并据此来选择时间序列稳定点,窗体操作降低了被选像元的分辨率,但抑制了噪声相位的影响;干涉图叠加方法（interferogram stacking）是将多幅差分干涉图进行叠加,提高结果中形变信息对大气干扰的相对精度,可以获取大区域的连续形变场;CR-InSAR技术将人工角反射器作为观测对象,通过建立CR点上的形变模型,实现对重点目标如滑坡、水库和断层的形变监测. 相似文献
5.
基于单像对的常规D-InSAR技术在形变量较大的地震同震形变场探测中已取得成功应用,但由于其受时间、空间失相干和大气影响的严重制约,难以应用于长期缓慢微小地壳形变的观测研究中.近几年发展起来的PS-InSAR(Permanent scatterer InSAR)技术是对常规D-InSAR的创新性发展,它通过将干涉处理对象集中在SAR图象中散射特性稳定的高相干点集上(人工建筑物或巨石、山峰等自然地物),避开非相干象元可能带来的各种复杂问题,从而间接克服了相位失相关和大气延迟的局限性,极大地提高了干涉测量的精度和可靠性,使基于InSAR技术的mm级微小地壳形变的遥感观测得以实现. 相似文献
6.
形变观测中小数据集PSInSAR的误差分析与初步应用 总被引：1，自引：0，他引：1
PS InSAR技术在微小形变的监测中有着独特的优势, 但同时受到数据量的严重制约。 本文以形变速率稳定的怀来县城为实验区, 利用15景ASAR数据, 依据主影像选择和高程改正选取了三种略有差异的模型分别进行PS处理, 并对形变提取中的相位解缠、 基线改正和高程改正进行误差分析。 结果表明, 小数据集的相位解缠和高程改正在部分PS点上容易发生错误, 但形变估计整体上能够正确反映实际情况。 三个模型中MS(Multi-Reference Single Regression) 模型得出结果最为可靠。 小数据集解算的整体PS点质量不高, 可以在满足PS点密度要求的前提下, 降低相位标准偏差阈值以提高解算的可靠性。 相似文献
7.
本文提出了结合永久散射体和准永久散射体干涉测量技术的时间序列合成孔径雷达（SAR）影像几何信息提取方案,利用2003～2008年获取的40景SAR影像量测并分析了三峡大坝运行时的稳定性问题及其周边区域的形变规律.我们发现在数据获取期间,三峡大坝左段的时效沉降基本停止,大坝形变受水位的影响较大,季节性变化也有一定体现.该实验结果和已发表的该坝段形变监测结果十分吻合.在数据处理结果中我们还在大坝上游秭归县附近堤坝发现一处形变异常.研究结果表明了时间序列SAR影像信息提取技术在大坝稳定性监测及坝区形变参数获取中的应用潜力. 相似文献
8.
9.
永久散射体雷达干涉(PSI)技术及其应用于区域地表形变监测已成为雷达遥感领域的研究热点之一.使用单一卫星平台所获取的单侧视SAR影像时间序列进行PSI分析,仅能获取沿雷达视线(LOS)方向的一维地表位移信息.本文提出了基于多平台永久散射体雷达干涉提取三维地表形变速度场的模型与算法,其基本策略是:首先针对每一卫星平台的SAR影像时间序列进行PSI分析,并计算各地面目标沿LOS向的位移速度值,然后联合各平台所对应的LOS向位移速度值进行建模,并基于最小二乘方法解算各地面目标的三维位移速度分量.实验选取天津市西北部作为测试区,使用2007—2010年所获取的39幅TerraSAR-X影像、23幅ENVISAT ASAR影像和16幅ALOS PALSAR影像进行分析,经联合解算得到了该测试区域的垂直位移速度场以及南北向和东西向水平位移速度分量.与地面水准和已有GPS观测结果对比分析表明:多平台PSI的垂直位移速度场精度可达毫米级,而其水平位移速度分量与已有GPS结果基本一致.多平台PSI分析无需引入任何外部形变参考信息,便可以实现形变场的偏差校准和三维形变场的恢复. 相似文献
10.
对于易发生地表形变的区域,传统DEM模型如SRTM,逐渐失去其时效特性,不能准确的描述地质特征,亟待更新重建.本文基于合成孔径雷达干涉测量(InSAR)采用SAR影像复数据相位信息提取地面三维信息的新技术,介绍了合成孔径雷达干涉测量数字高程模型建立的原理和方法.在此基础上,选取研究区,获取了Envisat ASAR SLC雷达影像数据,采用InSAR算法对研究区的数字高程模型进行了重建.并在研究区的形变区内外分别选取控制点,对重建DEM和SRTM进行比较分析.结果表明:对于易发生形变的特殊区域,传统DEM因失去其时效性,无法准确的描述地形特征;合成孔径雷达干涉测量可以作为此类地区DEM定期重建的有效手段.最后对重建的DEM实现三维可视化,提高了读图效率和成图质量. 相似文献
11.
12.
Mariarosaria Manzo Yuri Fialko Francesco Casu Antonio Pepe Riccardo Lanari 《Pure and Applied Geophysics》2012,169(8):1463-1482
We investigate the capabilities and limitations of the Differential Interferometric Synthetic Aperture Radar (DInSAR) techniques, in particular of the Small BAseline Subset (SBAS) approach, to measure surface deformation in active seismogenetic areas. The DInSAR analysis of low-amplitude, long-wavelength deformation, such as that due to interseismic strain accumulation, is limited by intrinsic trade-offs between deformation signals and orbital uncertainties of SAR platforms in their contributions to the interferometric phases, the latter being typically well approximated by phase ramps. Such trade-offs can be substantially reduced by employing auxiliary measurements of the long-wavelength velocity field. We use continuous Global Positioning System (GPS) measurements from a properly distributed set of stations to perform a pre-filtering operation of the available DInSAR interferograms. In particular, the GPS measurements are used to estimate the secular velocity signal, approximated by a spatial ramp within the azimuth-range radar imaging plane; the phase ramps derived from the GPS data are then subtracted from the available set of DInSAR interferograms. This pre-filtering step allows us to compensate for the major component of the long-wavelength range change that, within the SBAS procedure, might be wrongly interpreted and filtered out as orbital phase ramps. With this correction, the final results are obtained by simply adding the pre-filtered long-wavelength deformation signal to the SBAS retrieved time series. The proposed approach has been applied to a set of ERS-1/2 SAR data acquired during the 1992–2006 time interval over a 200?×?200?km area around the Coachella Valley section of the San Andreas Fault in Southern California, USA. We present results of the comparison between the SBAS and the Line Of Sight (LOS)—projected GPS time series of the USGC/PBO network, as well as the mean LOS velocity fields derived using SBAS, GPS and stacking techniques. Our analysis demonstrates the effectiveness of the presented approach and provides a quantitative assessment of the accuracy of DInSAR measurements of interseismic deformation in a tectonically active area. 相似文献
13.
Fabio Canova Cristiano Tolomei Stefano Salvi Giovanni Toscani Silvio Seno 《地球表面变化过程与地形》2012,37(3):273-286
The paper presents the results of a multi‐temporal, differential interferometric synthetic aperture radar (DInSAR) analysis aiming to identify active surface deformation phenomena in south‐eastern Sicily. The study area has been chosen because of its strong seismicity, high concentration of industrial and agricultural activities, and high density of people living in the coastal area. Furthermore, the morphology, lithology and climatic features of this sector of the Hyblean foreland are suitable for an interferometric analysis, providing a high coherence over the area. The Small BAseline Subset (SBAS) multitemporal DInSAR technique was used to calculate mean ground velocity maps and displacement time series from a large data set of European Remote Sensing Satellites (ERS 1–2) images spanning the time period 1992–2000. The reliability of the DInSAR results was tested calculating the EastSAR and UpSAR values over two permanent global positioning system (GPS) stations in the area, and comparing them with the EastGPS and UpGPS values. The residuals between GPS and DInSAR velocities were 1 and 0.6 mm/yr for the Up and East components, respectively. Four main subsiding areas, previously undetected, have been identified, corresponding with the towns of Augusta, Siracusa, Priolo, and Villasmundo. The observed deformation phenomena are located within coastal structural basins, filled with Pleistocene and Holocence deposits, except the Villasmundo land subsidence, which is located on the Hyblean plateau. The measured deformation rates reach values up to ?18 mm/yr in Augusta, –6 mm/yr in Siracusa, –5 mm/yr in Villasmundo and ?4.5 mm/yr in Priolo. The examination of velocity profiles, time series, and geological data allows us to relate all the detected deformation patterns primarily to groundwater over‐exploitation. A multi‐dimensional interpolation with kriging was performed to obtain a field subsidence map. A first‐order elastic deformation model was used to simulate the peculiar features of the Villasmundo subsidence. Copyright © 2011 John Wiley & Sons, Ltd. 相似文献
14.
15.
DInSAR measurements of ground deformation by sinkholes,mining subsidence,and landslides,Ebro River,Spain 总被引：1，自引：0，他引：1
Carmen Castañeda Francisco Gutiérrez Michele Manunta Jorge P. Galve 《地球表面变化过程与地形》2009,34(11):1562-1574
Differential Interferometric Synthetic Aperture Radar (DInSAR) has been applied to detect and measure ground deformation in a stretch of the Ebro River valley (Spain) excavated in salt‐bearing evaporites. The capability of the Small Baseline Subset (SBAS) DInSAR technique to detect ground displacement is analyzed comparing the DInSAR results with the available geomorphological information. The deformation map derived from 27 European Remote Sensing (ERS) satellite images covering more than five years provides sub‐centimeter displacement measurements in zones coinciding with known active sinkholes and landslides. Moreover the map provides the first account of mining subsidence in the area. The measured deformation rates reach 1·68 cm/y for the sinkholes, 0·80 cm/y for the landslides and 1·45 cm/y for the area affected by mining subsidence. The SBAS DInSAR technique provided deformation measurements in a small proportion (5–10%) of the known active sinkholes and landslides. This limitation is mainly due to the lack of coherence in agricultural areas, the spatial resolution of the deformation map (pixel size of 90 m), and the parallelism between the ERS satellite line of sight and the linear escarpment on which most of the landslides occur. Despite this, the interferometric technique provides valuable data that complement traditional geomorphological studies including the quantification of the deformation phenomena, the identification of mining subsidence otherwise only recognizable by geodetic methods, and the detection of creep deformation which might correspond to premonitory indicators of catastrophic sinkholes and landslides capable of causing the loss of lives. Detailed DInSAR studies combined with field data would be required to improve the analysis of each deformation area. Copyright © 2009 John Wiley & Sons, Ltd. 相似文献
16.
合成孔径雷达干涉测量(DInSAR)以厘米乃至毫米的精度和很大的空间覆盖范围实现地表形变观测,它是进行地壳形变观测的重要手段,在地震形变研究中发挥着越来越重要的作用。本文首先简要给出了微波雷达测量的特征,阐述了雷达图像数据处理的基本方法,分析了InSAR技术的主要影响因素和观测精度。结合较新的研究成果,分析了雷达遥感图像研究地震形变的方法,讨论了DInSAR在震间、同震和震后形变观测研究中的最新进展。同时讨论了目前我国应用DInSAR研究地震形变中面临的主要问题,最后阐述了应用雷达干涉测量研究地震形变的发展趋势。 相似文献
17.
《Journal of Volcanology and Geothermal Research》2006,151(4):399-416
The island of Ischia, located at the northwestern end of the Gulf of Napoli (Italy), is a volcanic area that is historically active (the Arso eruption, in 1302 and the Casamicciola earthquake, in 1883) and has diffuse hydrothermal phenomena. We present in this work a study of the surface deformation occurring in the island, which is based on applying the Differential Synthetic Aperture Radar Interferometry (DInSAR) algorithm referred to as Small BAseline Subset (SBAS) technique. This study is focused on the 1992–2003 time interval and SAR data acquired by the European Remote Sensing (ERS) satellites from ascending and descending orbits have been used, thus allowing us to discriminate the vertical and east–west components of the displacements. A validation of the DInSAR results has been carried out first by comparing the vertical deformations estimated from the SAR data with those measured from the spirit leveling network that is present in the area. In particular, we computed the difference between the mean vertical deformation velocities estimated from the SAR and the corresponding geodetic measurements along three main leveling lines; the maximum value of the root mean square difference is of about 1 mm/yr. The final discussion is dedicated to the interpretation of the detected displacements, benefiting from the overall information extracted from the ascending and descending DInSAR measurements. In particular, DInSAR data relative to the vertical deformation component show that the present-day subsidence of Ischia mainly develops in areas characterized by active landsliding and along faults; moreover, the deflation of the island, which is recorded by the horizontal displacement component, is probably related to the de-pressurization of the hydrothermal system. 相似文献
18.
为了削弱大气延迟对干涉结果的影响以提高InSAR的测量能力,本文在InSAR大气相位特征分析的基础上,研究了一种新的InSAR大气相位建模与估计方法.首先采用稳健估计确定大气垂直分层部分的模型参数,然后利用基于Matern模型的Kriging插值估计大气紊流部分,最后应用估计的大气垂直分层和紊流资料改正InSAR测量结果.利用覆盖河南义马地区的ASAR数据对本文提出的方法进行了验证,结果表明去除大气影响后,InSAR重建的DEM与参考DEM的高程差异的均方误差由19.5m降至5.3m,精度提高了约72%.同时,改正后的干涉图更合理地揭示了义马矿区的沉降漏斗情况,进一步验证了本文方法的有效性. 相似文献