共查询到19条相似文献，搜索用时 484 毫秒
1.
为检验抗侧刚度比和支撑布置方式等因素对具有不同总层数的屈曲约束支撑钢框架的抗震性能影响,借助SAP2000软件,探讨6层、12层、18层屈曲约束支撑钢框架结构在抗侧刚度比分别为1、2、3、4、5共五种工况及倒V型和单斜向两种支撑布置方式下的抗震性能。结果表明,屈曲约束支撑钢框架结构基底剪力-顶点位移曲线呈典型的双线性特征;随抗侧刚度比的增大,结构的层间位移角总体上呈降低趋势,基底剪力及支撑轴力增大,顶点水平位移变小,框架所分担的剪力降低;倒V型布置支撑较单斜向布置具有略大的基底剪力、谱加速度,较小的顶点位移、层位移、层间剪力和框架剪力分担率。分析表明,总体上来看,倒V型布置较单斜向布置时支撑框架结构具有略优的抗震性能;抗侧刚度比较支撑布置方式对支撑框架结构抗震性能的影响更为显著。 相似文献
2.
3.
将参数化建模的方法引入减震结构的分析与设计中,通过预设目标和迭代优化计算,以天水市某高层住宅消能减震结构为例,寻找最优的阻尼器布置方案。为评估和验证该消能减震结构的抗震性能,分别采用Perform 3D和ETABS等软件分析结构在多遇和罕遇地震作用下的结构响应,分析结果表明：小震作用下,消能减震结构的楼层位移、层间位移角、楼层弯矩及楼层剪力均减小6.5%以上,达到了设计要求;大震作用下,结构框架柱、框架梁、剪力墙和阻尼器能够满足既定的性能要求,层间位移角满足规范限值,能够达到“大震不倒”的设计目标,研究结果为实际工程预设减震目标和阻尼器优化布置提供参考。 相似文献
4.
本研究以实际建筑工程为例,应用有限元软件SAP2000对装配式屈曲约束支撑结构与普通支撑结构进行了弹塑性时程分析,对比了两种建筑结构在8度罕遇地震作用下的层间位移角和基底剪力的差异.结果表明:两种建筑结构的最大层间位移角均小于规范弹塑性层间位移角限值1/50;随着楼层增加,装配式屈曲约束支撑结构的层间位移角小于普通支撑... 相似文献
5.
研究屈曲约束支撑半刚性连接框架弹塑性位移计算方法,为这种结构抗震设计提供依据.推导了屈曲约束支撑半刚性连接框架结构侧移刚度计算方法,通过计算屈曲约束支撑和半刚性连接在罕遇地震作用下的有效阻尼比,修正弹性设计反应谱,再利用修正后的设计反应谱进行结构弹塑性层间位移简化计算.通过与弹塑性时程分析对提出的计算方法进行验证.基于有效阻尼比的思想给出的弹塑性位移的简化计算方法可进行屈曲约束支撑半刚性连接框架罕遇地震下的抗震设计. 相似文献
6.
消能支撑框架结构设计方法探讨 总被引：4，自引：0，他引：4
本文提出了一种新的消能支撑框架结构设计方法，该方法能够实现罕遇地震下结构的目标位移控制，其主要设计思路是框架主体结构按非抗震设计或降低烈度进行抗震设计，消能支撑则由罕遇烈度地震下满足给定层间位移角限值的优化计算来确定。本文还给出了一个15层框架结构的设计算例，并把本文方法的设计结果与按常规方法的设计结果进行了比较。 相似文献
7.
8.
由于受制于计算机软件中的消能减震单元,目前尚无较适用的静力分析方法应用于消能减震结构在多遇地震和罕遇地震下的结构分析。有关含消能减震部件的结构分析,主要以动力时程分析和动力弹塑性时程分析方法为主,因此具有较大的难度和需要很长的分析时间。为了推进结构消能减震于工程项目上的应用,缩短分析上的繁杂程序,依据《建筑抗震设计规范》,配合美国FEMA 356规范,提出一套消能减震结构在多遇地震下的等值线性分析方法和在罕遇地震下的静力非线性推覆分析方法（pushover analysis）。此方法适用于位移型阻尼器和防屈曲支撑,不但可使消能减震结构的结构分析简化,并可避免计算机软件的限制,且在不含阻尼器元素的计算机软件上,依然可做消能减震结构在多遇地震和罕遇地震下的结构分析。并介绍了此分析方法在消能减震结构的结构分析中的应用,以证明其可行性。 相似文献
9.
10.
11.
Seismic design and experiment of single and coupled corner gusset connections in a full‐scale two‐story buckling‐restrained braced frame 
下载免费PDF全文
下载免费PDF全文 Pao‐Chun Lin Keh‐Chyuan Tsai An‐Chien Wu Ming‐Chieh Chuang Chao‐Hsien Li Kung‐Juin Wang 《地震工程与结构动力学》2015,44(13):2177-2198
A gusset plate is subjected to forces induced from a buckling‐restrained brace (BRB) and frame action. In this study, a performance‐based design method of the gusset connections incorporating a BRB and frame actions is investigated. The force demands resulting from the BRB axial force are computed from the generalized uniform force method. The force demands induced from the frame action effects primarily result from beam shear. A conservative method, which considers the beam axial force effect and the thereafter reduced beam flexural capacity possibly developed at the gusset tips, is adopted in estimating the maximum beam shear. An improved equivalent strut model is used to represent the gusset plate subjected to the frame action effect. The total force demands of the gusset connection are combined from the BRB force and the frame actions. For design purposes, the stress distributions on the gusset interfaces are linearized. The maximum von Mises stress combining the normal and shear stresses is considered as the demand for the gusset plate design. In order to verify the effectiveness of the proposed design method, experiments on a two‐story full‐scale buckling‐restrained braced frame (BRBF) were performed. The chevron and single diagonal brace configurations were arranged in the second and the first stories, respectively. Two different corner gusset connection configurations including one single corner gusset and one coupled corner gusset connection, where two braces in adjacent stories joined at the same beam‐to‐column joint, were tested. The BRBF specimen was subjected to cyclically increasing lateral displacements with a maximum frame drift of 0.04 rad. The maximum story drifts reached 0.035 and 0.061 rad. in the first and the second stories, respectively. At the end of the tests, no fractures were observed on any of the gusset interfaces. Along the gusset interfaces, the normal and shear stress distributions computed from the proposed design procedures and the FEM analysis correlated well with the experimental results. This paper concludes with the procedure and recommendations for the performance‐based design of gusset connections. Copyright © 2015 John Wiley & Sons, Ltd. 相似文献
12.
Hybrid experimental performance of a full‐scale two‐story buckling‐restrained braced RC frame 下载免费PDF全文
下载免费PDF全文 An‐Chien Wu Keh‐Chyuan Tsai Hsun‐Horng Yang Jie‐Luen Huang Chao‐Hsien Li Kung‐Juin Wang Hsen‐Han Khoo 《地震工程与结构动力学》2017,46(8):1223-1244
This paper proposes a novel implementation of buckling‐restrained braces (BRB) in new reinforced concrete (RC) frame construction. Seismic design and analysis methods for using a proposed steel cast‐in anchor bracket (CAB) to transfer normal and shear forces between the BRB and RC members are investigated. A full‐scale two‐story RC frame with BRBs (BRB‐RCF) is tested using hybrid and cyclic loading test procedures. The BRBs were arranged in a zigzag configuration and designed to resist 70% of the story shear. The gusset design incorporates the BRB axial and RCF actions, while the beam and column members comply with ACI 318‐14 seismic design provisions. Test results confirm that the BRBs enhanced the RCF stiffness, strength, and ductility. The hysteresis energy dissipation ratios in the four hybrid tests range from 60% to 94% in the two stories, indicating that BRBs can effectively dissipate seismic input energy. When the inter‐story drift ratio for both stories reached 3.5% in the cyclic loading test, the overall lateral force versus deformation response was still very stable. No failure of the proposed steel CABs and RC discontinuity regions was observed. This study demonstrates that the proposed design and construction methods for the CABs are effective and practical for real applications. Copyright © 2016 John Wiley & Sons, Ltd. 相似文献
13.
The design of a three‐story buckling‐restrained braced frame (BRBF) with a single‐diagonal sandwiched BRB and corner gusset was evaluated in cyclic tests of a one‐story, one‐bay BRBF subassembly and dynamic analyses of the frame subjected to earthquakes. The test focused on evaluating (1) the seismic performance of a sandwiched BRB installed in a frame, (2) the effects of free‐edge stiffeners and dual gusset configurations on the corner gusset behavior, (3) the frame and brace action forces in the corner gusset, and (4) the failure mode of the BRBF under the maximum considerable earthquake level. The subassembly frame performed well up to a drift of 2.5% with a maximum axial strain of 1.7% in the BRB. Without free‐edge stiffeners, the single corner gusset plate buckled at a significantly lower strength than that predicted by the specificationof American Institute of Steel Construction (2005). The buckling could be eliminated by using dual corner gusset plates similar in size to the single gusset plate. At low drifts, the frame action force on the corner gusset was of the same magnitude as the brace force. At high drifts, however, the frame action force significantly increased and caused weld fractures at column‐to‐gusset edges. Nonlinear time history analyses were performed on the three‐story BRBF to obtain seismic demands under both design and maximum considerable levels of earthquake loading. The analytical results confirmed that the BRB and corner gusset plate achieved peak drift under cyclic loading test. Copyright © 2011 John Wiley & Sons, Ltd. 相似文献
14.
新版抗震设防烈度区划图实施以来,大量单跨框架结构校舍因抗侧力体系不合理以及抗震承载力不足急需加固改造。针对单跨框架结构不满足刚度及承载力要求的现状,提出并阐述了BRB减震与橡胶隔震联合加固技术原理,并对昆明某实际单跨框架结构进行了动力弹性和弹塑性有限元分析,结果表明:在多遇地震下,防屈曲支撑（BRB）未屈服,结构整体处于弹性;在设防地震作用下,部分BRB屈服耗能,结构层间位移角最大值为1/582,结构主体处于弹性阶段;在罕遇地震作用下,所有BRB屈服耗能,且其滞回曲线饱满,结构弹塑性层间位移角最大值为1/148,大部分梁端部产生塑性铰,少数柱产生塑性铰,且梁较柱先出铰,表现出良好的抗震性能。研究为单跨框架结构的加固提供一条有效的新途径。 相似文献
15.
Seismic retrofit of reinforced concrete frames using buckling‐restrained braces with bearing block load transfer mechanism 下载免费PDF全文
下载免费PDF全文 Kuan‐Yu Pan An‐Chien Wu Keh‐Chyuan Tsai Chao‐Hsien Li Hsen‐Han Khoo 《地震工程与结构动力学》2016,45(14):2303-2326
A new method of retrofitting reinforced concrete (RC) frames with buckling‐restrained braces (BRBs) to improve frame strength, stiffness and energy dissipation is proposed. Instead of typical post‐installed anchors, load is transferred between the BRB and RC frame through compression bearing between an installed steel frame connected to the BRB, and high‐strength mortar blocks constructed at the four corners of the RC frame. This avoids complex on‐site anchor installation, and does not limit the allowable brace force by the anchor strength. Cyclic displacements of increasing amplitudes were imposed on two RC frame specimens retrofitted with different BRB strength capacities. In one of the frames, the bearing blocks were reinforced with wire mesh to mitigate cracking. A third RC frame was also tested as a benchmark to evaluate the retrofit strength and stiffness enhancements. Test results indicate that the proposed method efficiently transferred loads between the BRBs and RC frames, increasing the frame lateral strength while achieving good ductility and energy‐dissipating capacity. When the bearing block was reinforced with wire mesh, the maximum frame lateral strength and stiffness were more than 2.2 and 3.5 times the RC frame without the BRB respectively. The BRB imposes additional shear demands through the bearing blocks to both ends of the RC beam and column member discontinuity regions (D‐regions). The softened strut‐and‐tie model satisfactorily estimated the shear capacities of the D‐regions. A simplified calculation and a detailed PISA3D analysis were shown to effectively predict member demands to within 13.8% difference of the measured test results. Copyright © 2016 John Wiley & Sons, Ltd. 相似文献
16.
17.
A welded end‐slot buckling‐restrained brace (WES‐BRB) has been developed at the Taiwan National Center for Research on Earthquake Engineering (NCREE). A steel frame equipped with a WES‐BRB can offer a cost‐effective solution to meet interstory drift and earthquake‐resistant design requirements for seismic steel buildings. According to the WES‐BRB and connection design procedure proposed by NCREE, there are seven key elements of a buckling‐restrained braced frame (BRBF) design that require design checking. In order to assist an engineer with the design of the WES‐BRB members and connections, an innovative cloud service named Brace on Demand has been constructed at NCREE. In this study, using 581 BRBF design examples, the effectiveness of the proposed design procedures to meet all design checks is demonstrated. It is found that the most critical limit states for an initial design are joint region buckling, gusset plate buckling, and gusset‐to‐beam and gusset‐to‐column interface strength. Accordingly, the causes of improper designs and associated strategies for improving the initial designs are discussed in this paper. Recommendations on initial selections including the BRB joint size and gusset plate thickness are given. The paper provides the detailed road map for engineers to develop the spreadsheet for BRB and connection designs. Copyright © 2014 John Wiley & Sons, Ltd. 相似文献
18.
Bidirectional substructure pseudo‐dynamic tests and analysis of a full‐scale two‐story buckling‐restrained braced frame 下载免费PDF全文
下载免费PDF全文 Hsen‐Han Khoo Keh‐Chyuan Tsai Ching‐Yi Tsai Cheng‐Yu Tsai Kung‐Juin Wang 《地震工程与结构动力学》2016,45(7):1085-1107
A two‐story buckling‐restrained brace (BRB) frame was tested under bidirectional in‐plane and out‐of‐plane loading to evaluate the BRB stability and gusset plate design. The test comprised pseudo‐dynamic loadings using the 1999 Chi‐Chi earthquake scaled to the 50%, 10%, and 2% probability of exceedance in 50 years and a cyclic regime of increasing amplitudes of up to 3.0% story drift ratio (SDR). The specimen had a unique configuration where the beams were connected to the columns through shear tabs welded to the column flanges and bolted to the beam webs. Stable hysteretic behavior with only minor cracking at the gusset‐to‐column welds was observed under the pseudo‐dynamic tests, with maximum in‐plane and out‐of‐plane SDRs of 2.24% and 1.47% respectively. Stable behavior continued into the cyclic test where fracture of the gusset‐to‐column welds occurred in the first cycle to simultaneous bidirectional SDR of 3.0%. The observed BRB stability is consistent with a methodology developed for BRB frames under simultaneous in‐plane and out‐of‐plane drifts. The specimen behavior was studied using a finite element model. It was shown that gusset plates are subjected to a combination of BRB force and frame action demands, with the latter increasing the gusset‐to‐beam and gusset‐to‐column interface demands by an average of 69% and 83% respectively. Consistent with the test results, failure at the gusset‐to‐column interfaces is computed when frame action demands are included, thus confirming that not considering frame action demands may results in unconservative gusset plate designs. Copyright © 2016 John Wiley & Sons, Ltd. 相似文献
19.
Computational study of self‐centering buckling‐restrained braced frame seismic performance 下载免费PDF全文
下载免费PDF全文 Recent research developed and experimentally validated a self‐centering buckling‐restrained brace (SC‐BRB) that employs a restoring mechanism created using concentric tubes held flush with pretensioned shape memory alloy rods, in conjunction with a buckling‐restrained brace (BRB) that dissipates seismic energy. The present computational study investigated how the SC‐BRB can be implemented in real buildings to improve seismic performance. First, a computational brace model was developed and calibrated against experimental data, including the definition of a new cyclic material model for superelastic NiTi shape memory alloy. A parametric study were then conducted to explore the design space for SC‐BRBs. Finally, a set of prototype buildings was designed and computationally subjected to a suite of ground motions. The effect of the lateral resistance of gravity framing on self‐centering was also examined. From the component study, the SC‐BRB was found to dissipate sufficient energy even with large self‐centering ratios (as large as 4) based on criteria found in the literature for limiting peak drifts. From the prototype building study, a SC‐BRB self‐centering ratio of 0.5 was capable of reliably limiting residual drifts to negligible values, which is consistent with a dynamic form of self‐centering discussed in the literature. Because large self‐centering ratios can create significant overstrength, the most efficient SC‐BRB frame designs had a self‐centering ratio in the range of 0.5–1.5. Ambient building resistance (e.g., gravity framing) was found to reduce peak drifts, but had a negligible effect on residual drifts. Copyright © 2014 John Wiley & Sons, Ltd. 相似文献