共查询到20条相似文献，搜索用时 467 毫秒
1.
Excess pore pressure and grain crushing of sands by means of undrained and naturally drained ring-shear tests 总被引：5，自引：0，他引：5
An investigation of excess pore-pressure generation of a weathered granitic sand, taken from the source area of a typical landslide caused as a result of liquefaction, and a fine silica sand was conducted, in which grain crushing within the shear zone of ring-shear test specimens was examined as the key phenomenon of rapid long-runout motion of landslides. In order to investigate and explain the low average apparent-friction angle, mobilized in a liquidized landslide, speed-controlled ring-shear tests were conducted under undrained conditions on weathered granitic-sand specimens, formed under a wide range of initial void ratios. It was revealed that very small steady-state shear resistances were obtained irrespective of the initial void ratios, which can explain the low average apparent-friction angle. In addition, two series of ring-shear tests on weathered-granitic and fine-silica sands were conducted under naturally drained conditions by keeping the upper drain valve of the shear box open during the tests. The first series of tests was performed under differing total normal stresses, but at the same shear speed, and the second series was conducted at differing shear speeds, but under the same total normal stress. In order to investigate and analyze excess pore-pressure generation and dissipation within the shear zone that is associated with grain crushing, permeability analyses were conducted by passing water through the sample box of the ring-shear test apparatus before and after shearing. In addition, grain-size distribution analyses of samples taken from the shear zone after shearing were carried out. For the weathered granitic-sand samples, a significant change in bulk permeability and large amount of grain crushing were observed. In these tests on the above soil, a considerable reduction of shear resistance, which increased proportionally to the total normal stress and shear speed, were obtained. It was observed that due to grain crushing, finer grains that lowered the permeability of the soil in the shear zone, were formed. It is likely that the decrease in permeability facilitated the generation of high excess pore pressures by reducing the pore-pressure dissipation rate from the shear zone; thus, flow behaviour was exhibited even under naturally drained conditions. 相似文献
2.
本文的主要目的是探讨地震诱发的高速远程滑坡的液化机理。通过排水和不排水环剪的对比试验,以及对地震诱发的不同类型的滑坡实例的现场调查,考察了土结构破坏和土粒子破碎产生的滑动带液化的不同机理。土结构破坏引起的液化在滑坡发生时即可产生,而土粒子破碎引起的液化需要在滑动过程中产生。在此基础上提出了滑动带向滑体内的扩展模型,并分析了两种液化机理引起的滑坡体形态的差异。本文的独到之处在于揭示了土粒子破碎对高速远程滑坡的重要影响,强调了在滑坡灾害预测研究中必须同等重视滑坡体结构和土粒子易破碎性的调查分析。 相似文献
3.
Aurelian Catalin Trandafir Kyoji Sassa 《Geotechnical and Geological Engineering》2006,24(6):1627-1639
This paper outlines a methodology for evaluating the likelihood of catastrophic landslide occurrence on gentle slopes in liquefiable
soils during earthquake. The approach is based on a modified Newmark sliding block model of assessing the earthquake-induced
undrained landslide displacements for conditions of no shear stress reversals on the sliding surface. By employing the shear
resistance-displacement relationship from undrained monotonic ring shear tests, the simulation model incorporates the sensitivity
of computed displacements to variations in yield acceleration. The proposed approach involves an examination of undrained
seismic slope performance under various horizontal seismic waveforms scaled to different specific values of the peak earthquake
acceleration. An example problem illustrates how the proposed methodology may be used to demarcate, based on the magnitude
of permanent seismic displacement, the levels of low, moderate and high risk of catastrophic landslide on a gentle slope in
a saturated cohesionless soil susceptible to liquefaction during earthquake. 相似文献
4.
饱和重塑黄土抗剪强度影响因素的试验研究 总被引：1，自引：0，他引：1
强降雨和灌溉导致黄土强度劣化并发生饱和破坏现象,进而诱发黄土滑坡,给当地带来严重的灾难。饱和黄土抗剪强度的影响因素较多,本文根据水头饱和与反压饱和相结合的原理,利用改装后的TFB-1型非饱和土应力-应变控制式三轴仪对党川地区马兰黄土重塑土样进行饱和试验和CU试验。分别采用50 kPa、100 kPa、200 kPa、400 kPa围压对饱和重塑黄土进行剪切速率分别为0.02 mm·min-1、0.06 mm·min-1、0.2 mm·min-1、0.4 mm·min-1的CU试验,探讨了围压和剪切速率对饱和重塑黄土抗剪强度的影响。研究发现:同一围压下,饱和重塑黄土的抗剪强度随着剪切速率的增大呈先增大后减小的趋势;同一剪切速率下,饱和重塑黄土的抗剪强度随着围压的增大逐渐增大;在干密度相同的条件下,饱和重塑黄土的总黏聚力及有效黏聚力随着剪切速率的增大先减小后增大,总内摩擦角及有效内摩擦角随着剪切速率的增大先增大后减小。该研究可为黄土滑坡预报和范围预测提供一定依据。 相似文献
5.
含水率对滑带土强度参数的影响 总被引：1，自引：0，他引：1
滑带土是滑坡体的重要组成部分,滑带土的强度特征对于边坡稳定具有重要的控制作用。三峡库区的黄土坡滑坡因常年经受库水位变化与降雨的影响,滑带土的含水率总是处于不断变化的过程中,因而对其强度参数产生了较大的影响。针对这一问题,在三峡库区黄土坡临江二号滑坡上采集了滑带土样,对不同含水率下的滑带土进行了不排水快剪试验。试验结果显示:含水率的变化对滑带土的抗剪强度影响较为敏感;试验数据拟合发现,滑带土的黏聚力C及内摩擦角φ均随含水率增大近似呈线性减小,且φ值降低的线性规律更趋明显。 相似文献
6.
Observation of shear zone development in ring-shear apparatus with a transparent shear box 总被引：1，自引：1，他引：1
Using a new ring-shear apparatus with a transparent shear box and video image analysis system, drained and undrained speed-controlled tests were conducted on coarse-grained silica sands to study the shear-zone formation process in granular materials. Velocity distribution profiles of grains under shear at various stages in the ring shear tests were observed through processing the video image by the Particle Image Velocimetry (PIV) program. Shear-zone thickness and type of shear mode (slide-like or flow-like) during shear were observed. Before reaching peak strength in low-speed and drained condition test, a comparatively major part of the sample in the upper shear box showed a velocity distribution profile of structural deformation and dilatancy behavior. After peak strength, the velocity profile changed into a slide-like mode and thereafter showed almost no change. In higher speed tests with drained and undrained conditions, an almost slide-like mode was observed, compared to low-speed test. Apparent shear-zone thicknesses of high-speed tests are thinner than low-speed tests. Unexpectedly, almost no difference was observed in the shear-zone thickness and mode of shear (slide or flow-like) between drained and undrained tests. This study was conducted as part of the International Programme on Landslides (IPL) M101 “Areal prediction of earthquake and rain induced rapid and long-traveling flow phenomena (APERITIF)” of the International Consortium on Landslides (ICL). These results will contribute to understanding the mechanism of shear-zone development in granular materials as a basic knowledge for disaster risk mitigation of rapid long run-out landslides. 相似文献
7.
Following a heavy rainstorm on 29 June 1999, hundreds of slope failures occurred in granitic mountains in Hiroshima Prefecture, Japan. Among these events, a highly mobile landslide (termed the Kameyama landslide in this paper), which occurred in Kameyama area of Hiroshima city, was the most catastrophic, and was investigated in detail. The displaced soil mass from the source area of this landslide traveled about 300 m and deposited a volume more than 10 times as great as that in the source area. The landslide originated in and traversed a valley-shaped concave slope covered by pre-existing colluvial debris deposits. In addition, a spring was visible in the source area and very shallow ground water was observed in an observation pit dug in the source area. Thus, it is inferred that the ground-water table rose quickly during the rainfall, and that this rise triggered the slope failure in the source area. Based on a field survey along the landslide cross section, a possible explanation for the mechanism of the landslide was obtained: the displaced soil mass from the source area impacted the debris deposit in the path of the landslide, thus triggering liquefaction failure of the saturated part of debris. The original landslide and the liquefied debris then moved downslope as a single mass. To examine this assumption, ring-shear tests were performed on samples taken from the source area. Undrained ring-shear tests on the saturated samples showed that the sample is highly liquefiable, and liquefaction failure could have been triggered in the debris deposits by a very small impact from the displaced soil mass of the initial failure. In addition, laboratory tests simulating the impacts on the debris deposits at natural water content, i.e., unsaturated (at the survey time, 2 days after the failure) showed that although shear failure could be caused by the assumed impact force, the displaced soils stopped after a few centimeters displacement, indicating that existence of a saturated zone in debris deposits is prerequisite for this kind of failure. 相似文献
8.
Noureddine Della Mostefa Belkhatir Ahmed Djafar Henni Jean Canou Jean Claude Dupla 《Arabian Journal of Geosciences》2014,7(8):2969-2980
In order to evaluate shear resistance characteristics of sand, which has previously experienced liquefaction, two series of drained and undrained monotonic triaxial compression tests on medium dense sand were carried out. In the first test series, the influence of the specimen preparation method and confining pressure has been studied. It was found that there was a marked difference in the behavior even though the density and stress conditions were identical. The conclusion was that the soil fabric was responsible for this result. In the second series of tests, the saturation influence on the shear resistance of the sand was examined. The results showed that the decrease in Skempton's pore pressure coefficient B improves the shear resistance and increases the friction angle of the sand. 相似文献
9.
不同环剪方式下滑带土残余强度试验研究 总被引：9，自引：0，他引：9
以三峡库区黄土坡滑坡滑带土为研究对象,利用环剪仪研究了黄土坡滑坡滑带土在单级剪、预剪以及多级剪3种环剪方式下的残余强度特征。试验结果表明：不同环剪试验下剪切带的形成与剪切位移相关;残余强度随有效法向应力的增大而增大,对于已经存在剪切带的滑带土,环剪时能很快达到残余强度状态;滑带土环剪轴向压缩分初始剪胀、颗粒运移压密和稳定压密3个阶段,且每个阶段剪应力变化趋势不同;预剪试验和多级剪切试验得到的残余强度偏大,应该首选单级剪切试验测试滑带土残余强度指标。 相似文献
10.
汪发武 《吉林大学学报(地球科学版)》2001,31(1):64-69
通过排水剪切试验，揭示出易于产生粒子破碎的土体易于产生体积变化，土体初始结构和粒子破碎难易度对体积变化各阶段的影响。在与之相对应的不排水试验中，产生粒子破碎的土体最终产生了较高的超孔隙水压力，而且孔隙水压力产生的各阶段与排水试验中的体积变化阶段具有良好的对应关系。揭示了不同诱因产生的高速滑坡的共同特征，即在长距离运动中，由于粒子破碎的影响，滑动面土体在不排水条件下，抗剪强度因超孔隙水压力上升而下降，最终导致高速滑坡。同时，由于粒子破碎将导致土体自身渗透系数降低，土粒子破碎因而具有促进超孔隙水压力产生和减缓超孔隙水压力消散的双重效果。 相似文献
11.
位于四川省茂县岷江左岸的周场坪滑坡为一大型深层蠕滑型古滑坡,其曾于1982年发生大规模快速复活并堰塞岷江。根据现场地质调查和工程地质钻探资料分析,该滑坡目前正处于深层蠕滑变形中,且降雨对滑坡变形速率具有重要影响。滑坡滑动速率和含水率对滑带土的力学强度特性,以及滑坡的变形和进一步破坏具有极大影响,为研究含水率和滑坡滑动速率对周场坪滑坡滑带土力学强度的影响,本文在滑带土基本物性测试分析基础上,开展了不同含水率(8%、15%和25%)和不同剪切速率(0.1 mm·min-1、5 mm·min-1和100 mm·min-1)的滑带土环剪试验。试验结果表明:在长距离剪切条件下,滑带土的抗剪强度随着含水率的增加而降低,且高含水率条件下强度降低幅度更大;随着剪切速率的增加,试样应变软化现象更加明显,其峰值强度和残余强度一般先增大后减小;由峰值强度和残余强度线性拟合的强度参数内摩擦角随剪切速率的增加则先增大后减小。研究认为在强降雨条件下,高含水率的条件使滑带土抗剪强度显著降低,易导致周场坪滑坡蠕滑加速,加快的滑动速率会再次降低滑带土的抗剪强度,从而导致滑坡发生周期性蠕滑,并可能再次发生整体复活堵塞岷江。 相似文献
12.
Because the construction of dams and hydro-electric power stations of Liujiaxia and Yanguoxia across the Yellow River in West Gansu Province, North-West China, inhabitants in the reservoir areas were resettled in Heifangtai Loess Platform. Irrigation thus started in 1968. Perched water table was significantly raised and resulted in many loess flow failures in the past 30 years. This type of landslide was often featured by long runout distance, high speed and recurrence. Laboratory tests along ICU and CSD stress paths were performed. It is shown that the loess has a strong strain-softening behavior and instability can occur in drained condition before undrained liquefaction. The failure mechanism of loess flow can be interpreted as the following process: with increasing perched water table, collapse in loess was first triggered in drained condition and led to undrained loading to adjacent soil in the lower saturated part of the loess platform. Under gravity loading applied by upper dry loess, undrained flow failure mobilized, eventually. 相似文献
13.
甘肃永靖黑方台4·29罗家坡黄土滑坡的特征 总被引：2，自引：1，他引：1
2015年4月29日上午,甘肃省永靖县盐锅峡镇黑方台滑坡高频发区的党川村罗家坡同一斜坡处连续发生了2次大规模黄土滑坡,总体积约65×10~4m~3,最大滑距630 m,摧毁14户居民房屋和3家工厂.通过现场详细调查、取样试验、1∶500地形测量、滑坡影像、视频等资料分析,对灌溉引发的罗家坡黄土滑坡的特征、滑动过程、形成机理进行了探讨.结果表明:第1次滑坡经过近2 a变形过程,整体突然失稳,高速远程滑动;第2次滑坡变形时间仅3 h,分块逐步滑动,滑动历时长而过程复杂,总体为低速远程滑动.高陡的地形和强度低、水敏感性强的土体是滑坡发生的基础,黄土台塬区长期农业灌溉是引发因素,大量水体入渗形成了20余米厚的饱和软弱基座,使抗剪强度降低,导致斜坡失稳滑动.黄土滑坡高速远程滑动的主要原因是滑坡剪出口位置高,滑动势能大,释放条件好,剪出口下部陡坡段为主要加速段;前方有开阔的滑动空间且有一定坡度、平缓的滑道;滑体底部饱和软弱黏性土在滑道上持续产生超孔隙水压力、液化等低摩阻效应,是远程滑动的润滑剂.同时,两次滑体间还存在冲击加速和能量传递作用. 相似文献
14.
常剪应力路径下含气砂土的三轴试验 总被引：1，自引：0，他引：1
天然气水合物完全分解时,产生的气体使得能源土孔隙压力急速增加,有效应力减小,进而引起土体液化破坏。此时深海能源土斜坡的应力状态与静力液化失稳过程可简化为含气土在常剪应力排水(或不排水)应力路径下的破坏问题。以此为背景,提出了制备含气砂土试样的改进充气管法,并开展了含气砂土的常剪应力路径三轴试验。22组试验结果表明:同一孔隙比的含气密砂在不同围压与常剪应力下具有相同的失稳线;含气砂土试样失稳时的应力比和体变均随初始相对密实度的增大而增大;含气密砂在常剪应力路径下饱和度对失稳特征影响的规律性在排水与不排水条件下均不明显,但在不排水条件下含气砂土的孔压(或体变)对变形的敏感性降低;含气密砂在常剪应力路径到达失稳点之后,排水条件下是瞬变的液化鼓胀破坏,不排水条件下是渐变的剪切破坏。 相似文献
15.
Evolution of Shear-Zone Structure in Undrained Ring-Shear Tests 总被引：4，自引：4，他引：0
Undrained monotonic torque-controlled tests were conducted on fine-grained silica sand to study the shear-deformation process in granular materials by using a ring-shear apparatus. Shear-zone structures at various stages in the undrained shear tests were observed during a series of tests in which the experiments were terminated at different shear displacement. For undisturbed samples, the shear zone was only developed during the post-failure stage and its thickness increased with progressed shearing. First the shear surfaces had undulating and asymmetric structures; later they gradually became smooth and parallel to the shearing direction. During this process, pore water pressure was generated, and the effective friction angle decreased correspondingly. Generally, the shear zone could be divided into three parts: the compacted core, the adjacent zone above the core, and the adjacent zone below the core. Grain-size analysis on the sample from the shear zone revealed that grain crushing occurred during each stage and the extent of grain crushing differed for different shear stages. An interesting phenomenon occurred during the steady-state deformation where the coarse and fine particles within the shear zone segregated during motions and a parallel orientation structure developed. These results are helpful for understanding the mechanism of progressive failure in granular material as well as the rapid landslide with long runout study. 相似文献
16.
为了分析剪切条件下零有效应力状态砂土的流动变形规律,对传统环剪仪进行了试样可视化改造,研制了透明环形剪切盒,通过对剪切盒膨胀性能分析及与标准砂的剪切试验对比,验证了环剪装置改造的合理性。通过分析不排水条件下饱和悬浮塑料砂的剪应力-应变曲线,发现其剪切强度具有应变软化的特性。通过分析环剪仪中饱和悬浮塑料砂试样的有效应力,证实了可视环剪试验中的土体基本处于零有效应力状态。开展了饱和悬浮塑料砂的流动变形可视环剪试验研究,结果表明：饱和悬浮塑料砂在固结不排水条件下剪切变形不连续,直接在剪切面发生断裂;在不固结不排水的条件下饱和悬浮塑料砂的剪切变形表现出流动形态,且与剪切速率有关：在低剪切速率下,剪切变形仅在剪切面处形成具有曲线轨迹的流动变形而在其他区域不发生变形;而在高剪切速率下剪切变形为整体的倾斜变形,符合黏性流体的流动变形特征。 相似文献
17.
甘肃黑方台滑坡类型与活动特征研究 总被引：2，自引：0，他引：2
由于农业灌溉水的长期入渗软化作用,1984-2019年甘肃黑方台已频繁发生滑坡灾害约150次,沿黄土塬边形成长约10公里的滑坡密集发育带。滑坡类型以中、小型黄土层内滑坡为主,占90%以上;大、中型黄土-泥岩顺层滑坡次之。黄土层内滑坡速度快、滑程远,突发性、频发性、继发性强;黄土-泥岩顺层滑坡速度慢、滑程近、复活性强。高陡的台缘地形和强度低、水敏感性强的岩土体和岩层倾向坡外的地质结构是滑坡发生的基础,台塬区长期大量的农业灌溉是主要引发因素,大量水体入渗软化斜坡岩土体,使抗剪强度降低,并形成了约20多米厚的饱和软弱基座,导致斜坡失稳滑动,侧压力、季节性冻结滞水和溶滤作用等也有一定影响。黄土层内滑坡高速远程滑动的主要原因是：滑坡剪出口位置高,滑动势能大,释放条件好,剪出口下部有陡坡加速段和开阔、平缓的滑动空间,滑体底部饱和软弱黏性土持续产生超孔隙水压力、液化等低摩阻效应,是远程滑动的润滑剂。黄土-泥岩顺层滑坡的主滑面沿外倾15°左右的泥岩层面发育,且剪出口位于斜坡下部坡脚部位,能量释放条件差,决定了黄土-泥岩顺层滑坡的滑动速度较低、滑动距离较短,滑体易再次复活滑动。 相似文献
18.
The influence of static shear stress on undrained cyclic behavior of nonplastic and low-plasticity silts has been studied
by means of undrained cyclic torque-controlled ring-shear tests. The cyclic and post-cyclic behavior of silty soils assumed
on sliding surface were investigated to assess the liquefaction potential and cyclically induced deformation of silty slopes.
Six different initial static shear stresses corresponding to slope angles from 0° to 25° were examined. To better understand
undrained cyclic behavior of silt governed by a change in clay content, three different mixtures were achieved by mixing of
nonplastic silt with 0%, 10%, and 20% of commercially available clay. These tests were conducted to simulate field conditions
prior to earthquake with initial static shear stresses corresponding to slopes and those with no initial static shear stresses
of level grounds. The gradual loss of mobilized undrained cyclic shear resistance after failure and pore water buildup in
relation to a number of cycles was observed. The undrained response of the soil to cyclic shear stress loading with the constant
amplitude revealed the significant effect of the initial static shear stress on the excess pore water pressure generation
and post-failure shear resistance. Test results showed that an increase in the initial static shear stress at the given initial
effective normal stress is associated with an increase of mobilized shear resistance at its peak state; however, the actual
resistance to liquefaction diminished for both nonplastic and low-plasticity silts. During both cyclic and post-cyclic stages
of loading, distinctly different types of shear deformation were identified. In order to evaluate mobility of landslides,
a modified conventional brittleness index for seismic loading, , was proposed and used to characterize unlimited deformation of silts. 相似文献
19.
Residual strength of slip zone soils 总被引：2，自引：1，他引：1
Slip zones of ancient landslides are commonly composed of fine-grained soils with amount of coarse-grained particle. Residual strength of slip zone soil is an important parameter for evaluating reactivation potential and understanding progressive failure mechanism. In this study, the residual strength is examined by in situ direct shear tests, improved laboratory reversal shear box test, precut specimen triaxial shear test and ring shear test. Some residual shear behaviors are recognized. Field residual strength is the average operational resistance along the sliding surface not an ideal drained strength, which is less than peak and greater than residual strength measured in laboratory. Stress–displacement curves obtained from in situ shear and laboratory reversal direct shear demonstrate strain-hardening which have no significant peak, but the shear stress is decreased gradually with increasing displacement. Residual friction coefficient depends on the normal stress, and this dependence is relevant to the interaction of rolling and sliding of particles. Residual friction angle is closely related to coarse fraction and dry density, appearing a linear increase with increasing coarse fraction and a form of polynomial function with increasing dry density. The influence of shearing rate on residual strength can be negligible. 相似文献