首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献,搜索用时 93 毫秒
1.
利用非奇变换首先将地形校正奇异积分非奇异,其次利用NewtonCotes积分,本文推导了几组适用于地形校正中央区积分的求积公式。  相似文献   

2.
利用非奇变换,将地形校正诸奇异积分转化为一组非奇异积分。理论分析和数值计算都表明,奇异积分非奇异后,可有效地提高地形校正中央区积分的精确度。  相似文献   

3.
利用非奇变换,将地形校正诸奇异积分转化为一组非奇异积分。理论分析和数值计算都表明,奇异积分非奇异后,可有效地提高地形校正中央区积分的精确度。  相似文献   

4.
地形影响的积分算法在中央区存在奇异性,为避免奇异问题可将中央区地形近似为与计算点等高的圆柱体。基于此,提出使用更接近实际网格地形的棱柱模型计算地形影响,并通过推导给出了中央区直接、间接影响的棱柱模型算法公式。当地形网格较小时,棱柱模型与圆柱模型计算的中央区直接影响的差异为正;当地形网格较大时差异为负,但对于中央区间接影响,棱柱模型与圆柱模型计算结果的差异总为负值。当地形高分别取1 000、2 000和3 000 m时,棱柱模型与圆柱模型计算的直接影响差异的极值分别约为±0.3、±0.5和±0.8 m Gal,而间接影响差异的极值分别约为-0.02、-0.12和-0.27 cm。对于高精度的应用需求,当区域海拔较高时建议采用本文提出的更符合实际地形的棱柱模型计算中央区直接、间接影响。  相似文献   

5.
论地形垂线偏差中央区贡献的计算   总被引:1,自引:2,他引:1  
边少峰  薛芳侠 《测绘学报》1997,26(1):33-36,57
本文根据Nowton‘s引力公式,推导出地形垂线偏差的求积公式,通过奇异积分变量变换,推出了一些新的地形垂线偏差计算公式,这些新的计算公式,有效的处理了中央区的奇异积分问题。  相似文献   

6.
简要介绍地形起伏对地面点重力梯度的影响,推导棱柱法计算重力梯度改正的严格积分公式并和积分核累加法对比验证了其正确性;将积分区域划分为中央区和远区,中央区采用严格的棱柱法进行计算,远区采用线性积分的方式逼近真实值,简化了积分过程;根据重力梯度应用的要求针对不同类型地形设定了中央区划分准则。实验表明:根据文中提出的方法和分区准则,相比于传统的积分法和棱柱法,计算速度得到提高,且精度要求相比于积分核累加法优于0.01E。  相似文献   

7.
针对考虑太阳直接辐射、天空散射辐射以及来自于附近地表反射辐射的复杂地形EMT 遥感影像地形校正物理模型公式复杂、计算繁琐、不易实施的特点以及存在过度校正的缺陷,对该物理模型进行简化和改进。提出一套简化模型相关参数,即r值,Vt,Vd,T↓(λ,θ)等的计算方案,从而简化计算过程,提高计算效率。并针对该地形校正物理模型朗伯体假设的缺陷,引入Minnaert参数k时模型进行非朗伯体修正。简化和改进的地形校正物理模型的校正实验结果表明该模型很好地消除了复杂地形EMT 遥感影像的地形阴影,从而证明该地形校正物理模型的简化和改进方案可行。  相似文献   

8.
马健  魏子卿 《测绘学报》2018,47(11):1429-1436
基于Helmert第二压缩法进行边值解算时需要计算地形压缩对重力的直接影响和对(似)大地水准面的间接影响。计算近区直接、间接影响的传统积分算法仍是二重积分形式。该算法以网格中心点处的积分核作为网格积分核的平均值的计算模式在一定程度上引入了近似误差。另外,直接、间接影响的传统积分算法在中央区存在奇异性,需单独计算中央网格地形影响,因而增加了计算的复杂性。为此,本文推导了近区地形直接、间接影响的棱柱模型公式,一方面提高了地形影响的计算精度;另一方面中央区不存在奇异性,从而简化了计算过程。为避免棱柱模型存在的平面近似误差,可使用顾及地球曲率的棱柱模型算法计算地形影响。最后通过试验得出结论,在(似)大地水准面精度要求较高的应用中,应尽量使用顾及地球曲率的棱柱模型算法计算地形影响。  相似文献   

9.
为提高利用逆Vening-Meinesz公式反演测高重力中央区效应的精度,视中央区为矩形域,将垂线偏差分量表示成双二次多项式插值形式,引入非奇异变换,推导出了重力异常的计算公式。以低纬度区域2′×2′的垂线偏差实际数据为背景场进行了计算,结果表明,当中央区包含4个网格时,传统公式与推导出的重力异常计算公式误差的最大值大于1 mGal。推导出的公式可为高精度测高重力中央区效应的计算提供理论依据。  相似文献   

10.
本文提出一种新的半经验地形校正模型SCEDIL(Simple topographic Correction using Estimation of Diffuse Light),该模型通过结合DEM与光学影像数据寻找局部区域内完全光照和阴影的水平像元,并以光照、阴影水平像元的平均反射率值估算局部区域散射辐射比,提高了陡峭山区影像的地形校正精度。以高分一号卫星和Landsat ETM+影像为例,从目视判读和定量分析两个方面,比较分析该算法与传统半经验地形校正算法(C、SCS+C)的校正结果。结果表明:(1)对较为平坦的地形,SCEDIL和C、SCS+C校正都有较好的目视结果;对地面起伏较大的陡峭地形,C、SCS+C校正后,原阴影区域易呈现破碎化特征,SCEDIL校正后,原阴影区域过渡较为平滑。(2)SCEDIL校正后,各波段反射率的均值和标准差优于C、SCS+C校正,SCEDIL校正后,影像总分类精度与同类地物光谱信息均一性均优于C和SCS+C校正。SCEDIL半经验地形校正方法能有效地去除影像中的地形干扰,尤其对陡峭地形的校正效果,优于常规地形校正模型。  相似文献   

11.
Positions and proper motions obtained from observations by the very large array (VLA) and the multi-element radio-linked interferometer network (MERLIN) are used to establish the link of the Hipparcos Celestial Reference Frame (HCRF) to the International Celestial Reference Frame (ICRF). The VLA and MERLIN data are apparently the latest ones published in the literature. Their mean epoch at around 2001 is about 10 years after the epoch of the Hipparcos catalogue and, therefore, the data are considered suitable to check the Hipparcos link established at epoch 1991.25. The parameters of the link, i.e., the angles of frame orientation and the angular rates of frame rotation, are estimated by fitting these parameters to the differences of the optical and radio positions and proper motions of stars common to the Hipparcos catalogue and the VLA and MERLIN data. Both the estimates of the angles of orientation and the angular rates of rotation show nearly consistent but insignificant results for all samples of stars treated. We conclude that not only the size of the samples of 9–15 stars is too small, but also that the accuracy of the radio positions and, above all, of the radio proper motions is insufficient, the latter being based on early-epoch star positions of low accuracy. The present observational data at epoch 2001 suggest that maintenance of the Hipparcos frame is not feasible at this stage.  相似文献   

12.
SENSOR: a tool for the simulation of hyperspectral remote sensing systems   总被引:1,自引:0,他引:1  
The consistent end-to-end simulation of airborne and spaceborne earth remote sensing systems is an important task, and sometimes the only way for the adaptation and optimisation of a sensor and its observation conditions, the choice and test of algorithms for data processing, error estimation and the evaluation of the capabilities of the whole sensor system.The presented software simulator SENSOR (Software Environment for the Simulation of Optical Remote sensing systems) includes a full model of the sensor hardware, the observed scene, and the atmosphere in between. The simulator consists of three parts. The first part describes the geometrical relations between scene, sun, and the remote sensing system using a ray-tracing algorithm. The second part of the simulation environment considers the radiometry. It calculates the at-sensor radiance using a pre-calculated multidimensional lookup-table taking the atmospheric influence on the radiation into account. The third part consists of an optical and an electronic sensor model for the generation of digital images. Using SENSOR for an optimisation requires the additional application of task-specific data processing algorithms.The principle of the end-to-end-simulation approach is explained, all relevant concepts of SENSOR are discussed, and first examples of its use are given. The verification of SENSOR is demonstrated. This work is closely related to the Airborne PRISM Experiment (APEX), an airborne imaging spectrometer funded by the European Space Agency.  相似文献   

13.
One type of aerial cableway consists of a continuous cable,which works at the same time as carrying cable and drawing cable.This kind of cableway is supported by many towers,which divide the total length in linear sections.even small deviations from the planed layout can increase the strain of the cable and the danger of derailments.The deviations of the position of the towers from the planed layout are due to local sliding or sinking of the foundation or other mechanical movements.Up to now the axis of the cableways were periodically measured by traditional methods. The goal of this project is to demonstrate the possibility of measuring the axis of a cableway with GPS techniques,while the cable is moving.The results show that the proposed measuring device provides precise results in a simple and reliable way.  相似文献   

14.
This paper provides a review of ground-based SAR (GBSAR) interferometry for deformation measurement. In the first part of the paper the fundamentals of this technique are provided. Then the main data processing and analysis stages needed to estimate deformations starting from the GBSAR observations are described. This section introduces the two types of GBSAR acquisition modes, i.e., continuous and discontinuous GBSAR, and reviews the different GBSAR processing and analysis methods published in the literature. This is followed by a discussion of the specific technical aspects of GBSAR deformation measurement. A section then summarizes the pros and cons of GBSAR for deformation monitoring. The last part of the paper includes two reviews: one concerning the GBSAR systems described in the literature, including non-strictly SAR systems and a second one addresses the main GBSAR applications.  相似文献   

15.
The monitoring of different crops (cultivated plots) and types of surface (bare soils, etc.) is a crucial economic and environmental issue for the management of resources and human activity. In this context, the objective of this study is to evaluate the contribution of multispectral satellite imagery (optical and radar) to land use and land cover classification.Object-oriented supervised classifications, based on a Random Forest algorithm, and majority zoning post-processing are used. This study emerges from the experiment on multi-sensor crop monitoring (MCM'10, Baup et al., 2012) conducted in 2010 on a mixed farming area in the southwest of France, near Toulouse. This experiment enabled the regular and quasi-synchronous collection of multi-sensor satellite data and in situ observations, which are used in this study. 211 plots with contrasting characteristics (different slopes, soil types, aspects, farming practices, shapes and surface areas) were monitored to represent the variability of the study area. They can be grouped into four classes of land cover: 39 grassland areas, 100 plots of wheat, 13 plots of barley, 20 plots of rapeseed, and 2 classes of bare soil: 23 plots of small roughness and 16 plots of medium roughness. Satellite radar images in the X-, C- and L-bands (HH polarization) were acquired between 14 and 18 April 2010. Optical images delivered by Formosat-2 and corresponding field data were acquired on 14 April 2010.The results show that combining images acquired in the L-band (Alos) and the optical range (Formosat-2) improves the classification performance (overall accuracy = 0.85, kappa = 0.81) compared to the use of radar or optical data alone. The results obtained for the various types of land cover show performance levels and confusions related to the phenological stage of the species studied, with the geometry of the cover, the roughness states of the surfaces, etc. Performance is also related to the wavelength and penetration depth of the signal providing the images. Thus, the results show that the quality of the classification often increases with increasing wavelength of the images used.  相似文献   

16.
郭忻怡  郭擎  冯钟葵 《遥感学报》2020,24(6):776-786
以滑坡蠕变阶段坡体的蠕变会引起环境条件的改变,进而影响植被生长状况的野外考察客观现实为依据,提出一种间接监测滑坡变化的新方法。利用高分辨率光学遥感技术,对滑坡蠕变阶段遥感影像上坡体上覆植被的异常特征进行判识,建立遥感影像上植被异常与滑坡蠕变的关系,反映滑坡的演化过程,弥补GPS技术、InSAR技术及部分地面监测手段在地势高、地形陡峭、植被茂盛等条件下监测工作的不足,为后续的滑坡预测研究提供帮助。以植被覆盖度较高的新磨村山体高位滑坡为例,首先,对研究区域进行分区;其次,计算各分区的植被覆盖度;最后,利用植被覆盖度分析遥感影像上的植被异常与滑坡蠕变的关系,并根据滑后遥感影像和实地考察情况进行验证。结果显示,2014年—2016年,滑坡的主要物源区、变形体上方细长局部崩滑区和泉眼及冲沟周边的植被覆盖度出现明显的下降,即随着滑坡发生时间的临近,植被受滑坡蠕变的影响变大,植被生长状况变差;而且随着距裸地等滑坡风险较大区域的距离增大,植被受滑坡蠕变的影响变小,植被生长状况变好。这表明,植被异常与滑坡蠕变存在明显的时空相关性,体现了滑坡蠕变阶段遥感影像上植被异常与滑坡蠕变的内在联系,反映了滑坡逐步失稳的演化过程,为进一步预测滑坡的发生提供依据。  相似文献   

17.
朱骏侠 《测绘通报》2021,(4):146-150
随着城市面貌日新月异,地下管网的建设也在持续推进,作为城市的地下“神经网络”,全天24 h保障城市的正常运转和发展。本文以实现城市管网管理系统的高可用、无插件、智能化为目标,采用“地上地下一体”“二三维一体”的设计理念,研究基于WebGL的三维智慧管网系统的关键技术,实现了管线设施管理的信息数字化、空间化与图形化。  相似文献   

18.
张采芳  张睿卓  林爱武 《测绘通报》2018,(3):134-138,146
随着移动定位、移动GIS与物联网等技术的不断发展,动态交通信息的服务能力和服务水平不断提升,对数据管理效率提出了更高要求。本文将本体应用到交通GIS中,借助本体概念层次结构和语义扩展等特性来组织和分析动态交通数据:首先应用本体论的理论和方法,从交通本体的层次模型出发,构建一个简单的交通应用本体;其次以实例的形式给出交通信息本体的系统应用框架;最终就动态交通信息本体实现与应用进行进一步论述。大量实测的试验数据结果表明,本文方法可解决交通信息领域中的多专题动态信息综合管理问题,促进交通信息管理与服务的提升。  相似文献   

19.
GridGNSS--网格化全球卫星导航系统   总被引:3,自引:0,他引:3  
计算机网络技术的发展已经使全球的信息资源实现网络互联和页面浏览,新一代的基于IPv6的IP地址方案的实施,将可以满足全球几乎任意的资源连接互联网的需要。随着移动通讯技术的发展,移动互联网和移动IP技术可以使移动用户通过网络实现全球资源的互联和访问。因此,对于通过全球卫星定位系统进行移动目标定位的用户,可以通过移动网络的方式实现传统的数据传输和通讯。随着新一代互联网络的的发展,WebService成为全球信息发布的最主要的平台,基于WebService的GNSS综合信息发布可以实现全球GNSS资源和信息的访问,计算机网格的出现为全球GNSS计算提供技术支持,本文基于网格技术,提出了GNSS网格和GridGNSS的概念,对GridGNSS的功能和研究内容进行了详细分析,并对GridGNSS的实现过程和应用进行了阐述。  相似文献   

20.
根据系统空间数据结构的特点 ,提出了图块_实体数据模型 ,有效地解决了对空间信息操作的复杂性 ,有利于施工中空间数据的动态更新和维护。该系统的空间数据结构为相关信息系统建立适宜的空间数据结构提供了一条可行的途径。  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号