共查询到20条相似文献，搜索用时 406 毫秒
1.
Review of a new shear-strength criterion for rock joints 总被引：44，自引：0，他引：44
Nicholas Barton 《Engineering Geology》1973,7(4):287-332
Barton, N., 1973. Review of a new shear-strength criterion for rock joints. Eng. Geol., 7: 287–332.
The surface roughness of rock joints depends on their mode of origin, and on the mineralogy of the rock. Amongst the roughest joints will be those that formed in intrusive rocks in a tensile brittle manner, and amongst the smoothest the planar cleavage surface in slates. The range of friction angles exhibited by this spectrum will vary from about 75° or 80° down to 20° or 25°, the maximum values being very dependent on the normal stress, due to the strongly curved nature of the peak strength envelopes for rough unfilled joints.
Direct shear tests performed on model tension fractures have provided a very realistic picture of the behaviour of unfilled joints at the roughest end of the joint spectrum. The peak shear strength of rough—undulating joints such as tension surfaces can now be predicted with acceptable accuracy from a knowledge of only one parameter, namely the effective joint wall compressive strength or JCS value. For an unweathered joint this will be simply the unconfined compression strength of the unweathered rock. However in most cases joint walls will be weathered to some degree. Methods of estimating the strength of the weathered rock are discussed. The predicted values of shear strength compare favourably with experimental results reported in the literature, both for weathered and unweathered rough joints.
The shear strength of unfilled joints of intermediate roughness presents a problem since at present there is insufficient detailed reporting of test results. In an effort to remedy this situation, a simple roughness classification method has been devised which has a sliding scale of roughness. The curvature of the proposed strength envelopes reduces as the roughness coefficient reduces, and also varies with the strength of the weathered joint wall or unweathered rock, whichever is relevant. Values of the Coulomb parameters c and Φ fitted to the curves between the commonly used normal stress range of 5–20 kg/cm2 appear to agree quite closely with experimental results.
The presence of water is found in practice to reduce the shear strength of rough unfilled joints but hardly to affect the strength of planar surfaces. This surprising experimental result is also predicted by the proposed criterion for peak strength. The shear strength depends on the compressive strength which is itself reduced by the presence of water. The sliding scale of roughness incorporates a reduced contribution from the compressive strength as the joint roughness reduces. Based on the same model, it is possible to draw an interesting analogy between the effects of weathering, saturation, time to failure, and scale, on the shear strength of non-planar joints. Increasing these parameters causes a reduction in the compressive strength of the rock, and hence a reduction in the peak shear strength. Rough—undulating joints are most affected and smooth—nearly planar joints least of all. 相似文献
2.
为了准确确定岩体力学参数,通过综合分析多种地质强度指标(GSI)量化方法,提出了一种改进的GSI值量化和修正方法。首先,利用测线法估算结构面平均间距(d)和岩体块度指数(RBI)的改进型岩体块度率(RBR),根据岩体三维结构面网络,获得岩体体积节理数(Jv)和岩体结构等级(SR),然后采用上述参数和结构表面条件(SCR)及结构表面特性参数(Jc)进行了GSI值的定量化处理。为了克服GSI体系的缺点,考虑结构面产状和地下水对岩体力学性质的影响,提出了GSI值的修正方法和公式。以某铅锌矿体的矿岩体为例,根据改进的GSI值量化和修正方法及Hoek-Brown强度准则来确定矿岩体力学参数,通过与原位变形试验的对比分析,验证了该方法的精确性和可行性。该方法为从室内岩石力学试验合理地获取节理岩体力学参数提供了理论及实现的依据。 相似文献
3.
提出了一种新的无网格数值模拟计算方法--广义粒子动力学法(GPD),并在GPD算法中引入了粒子损伤理论。运用GPD方法,建立了TBM单滚刀、双滚刀作用下的完整岩体破岩模型,成功模拟了TBM滚刀破岩过程。通过与数值模拟结果及室内试验结果的对比分析,验证了GPD法模拟TBM滚刀破岩过程的有效性。同时,运用GPD方法建立了含节理岩体及高围压条件下岩体的TBM滚刀破岩模型,研究了节理及围压条件下TBM滚动破岩过程。得到了节理对TBM滚刀破岩效率的影响,既可能是促进作用又可能是抑制作用,高围压对TBM滚刀破岩过程中裂纹的起裂及扩展和破岩深度有较大的影响。 相似文献
4.
目前对岩石结构表面粗糙度的研究往往只局限于地表,难以反映深部岩石节理粗糙度的特征。钻孔孔壁上节理轮廓线包含有三维信息的特点,本文开展了基于数字钻孔摄像技术的岩石节理粗糙度分形特征的研究,利用数字钻孔摄像系统获取地下深度岩石节理全景图,采用边缘检测技术从全景图中提取出节理轮廓线,对其进行空间变换和视距离变换得到地下岩石节理粗糙表面轮廓线的真实状况。与Barton提出的10条标准剖面曲线进行对比得到每条轮廓线的JRC值,并计算其分形维数,根据最小二乘法原理拟合出JRC与分形维数之间的关系为:(D)=JRC=-541.9x2+1362x-818.53。本文研究内容为描述地下深部天然节理的结构及其特征提供了基础,对更深入地研究地下深部岩石节理的表面空间状况有重要的意义。 相似文献
5.
通过室内大型直剪试验和基于PFC2D的颗粒离散元数值模型,探讨考虑块石破碎的土石混合料的剪切特性及块石破碎特征。以土石混合料室内大型直剪试验和筛分试验为基础,提出了一种能真实描述块石形态特征并准确反映块石破碎效应的土石混合料颗粒离散元数值建模方法,模拟并分析了6种含石量土石混合料在4种不同法向应力作用下的剪切特性及块石破碎特征。结果表明：土石混合料抗剪强度随含石量的增大而增大,且基本符合摩尔-库仑（M-C）强度准则,随着含石量增大,内摩擦角呈现“慢-快-慢”增长趋势,黏聚力则呈现先增后减再增大的变化趋势。剪切后土石混合料块石破碎形式可归纳为表面研磨、局部破碎、完全破裂、完全破碎4种方式。提出了一种新的颗粒破碎指标,该指标能够准确描述粒径大于5 mm的块石的破碎程度,其随含石量和法向应力的增大而增大。通过对土石混合料颗粒离散元数值模型剪切面的分析发现,剪切面出现“剪斜”现象,其起伏程度随含石量增大愈加明显,且随着含石量增大剪切面附近剪裂隙数量增多,土石混合料在剪切过程中的破坏为拉-剪混合破坏。 相似文献
6.
7.
岩石节理粗糙度系数的分形特征 总被引：5，自引：0，他引：5
岩石节理粗糙度系数JRC是估算节理抗剪强度和变形指标最重要的参数。通过对简易纵剖面仪获取的节理表面轮廓曲线的分形研究,讨论了节理表面轮廓曲线的自相似性和JRC的自相似性,并根据实测统计资料的分析,指出了分形理论研究JRC的适用条件和有效的使用方法。由实测统计资料的JRC尺寸效应自相似性分析,认为JRC尺寸效应具分形结构。本文介绍了一种确定JRC尺寸效应分维数D的方法,由此确定的分维数D具有明确的物理意义。 相似文献
8.
9.
基于地下岩体工程开挖扰动的实际情况,开展考虑持续开挖效应,充分反映岩体结构面应力调整过程的结构面剪切试验更具理论意义和工程应用价值。采用人工劈裂方法制备岩体结构面,开展了常规应力路径和持续开挖效应下的结构面剪切试验,系统研究了两种条件下结构面剪切力学性质、声发射特征和能量的演化规律。研究结果表明：开挖扰动荷载强度越大,结构面发生剪切破坏时的剪应力降整体上越大,但持续开挖效应下的剪应力降最大值仅为常规应力路径下剪应力降的48.57%;考虑持续开挖效应的结构面剪切过程中声发射活动主要集中于结构面受剪破坏和剪应力降产生时,且声发射活动强度与开挖扰动强度正相关,声发射振铃计数变化率极值明显小于常规应力路径下的相应值;持续开挖效应下试样裂纹发育密集度、结构面磨损区域及破坏程度均随开挖扰动强度增加而增加,但试样裂纹发育的密集程度和结构面破坏程度相对常规应力路径下的情况轻;考虑持续开挖效应的结构面发生剪切破坏时弹性应变能随扰动荷载增大而增大,均低于常规应力路径条件下的弹性应变能值,持续开挖效应降低了结构面剪切破坏的强度,但更易引发结构面发生剪切破坏。 相似文献
10.
Summary Discontinuities or joints in the rock mass have various shapes and sizes. Along with the joint orientation and spacing, the
joint persistence, or the relative size of the joint, is one of the most important factors in determining the block sizes
of jointed rock masses. Although the importance of joint persistence on the overall rock mass strength has long been identified,
the impact of persistence on rock strength is in most current rock mass classification systems underrepresented. If joints
are assumed to be persistent, as is the case in most designs, the sizes of the rock blocks tend to be underestimated. This
can lead to more removable blocks than actually exist in-situ. In addition, a poor understanding of the rock bridge strength
may lead to lower rock mass strengths, and consequently, to excessive expenditure on rock support.
In this study, we suggest and verify a method for the determination of the block sizes considering joint persistence. The
idea emerges from a quantitative approach to apply the GSI system for rock mass classification, in which the accurate block
size is required. There is a need to statistically analyze how the distribution of rock bridges according to the combination
of joint orientation, spacing, and persistence will affect the actual size of each individual block. For this purpose, we
generate various combinations of joints with different geometric conditions by the orthogonal arrays using the distinct element
analysis tools of UDEC and 3DEC. Equivalent block sizes (areas in 2D and volumes in 3D) and their distributions are obtained
from the numerical simulation. Correlation analysis is then performed to relate the block sizes predicted by the empirical
equation to those obtained from the numerical model simulation. The results support the concept of equivalent block size proposed
by Cai et al. (2004, Int. J. Rock Mech. Min. Sci., 41(1), 3–19). 相似文献
11.
岩体结构面粗糙度系数JRC的研究现状 总被引：1，自引：0，他引：1
岩体结构面粗糙度系数JRC是描述岩体结构面粗糙起伏状态的力学参数,对于无填充或少填充的硬性结构面而言是关键性指标。本文介绍了岩体结构面粗糙度系数JRC估算方法的理论及应用研究现状,并探讨了JRC研究中存在的几个问题。 相似文献
12.
节理岩体几何结构非常复杂,研究其渗流特性对于指导含水岩层稳定性分析具有重要价值。应用离散裂隙网络模型DFN方法,基于VC++6.0软件平台,建立了平面渗流分析方法,分析了节理岩体不同几何分布情况下的渗透率张量特征,通过定义渗流定向性系数对岩体渗流的定向性特征进行了定量分析。结果表明：单组节理岩体渗流具有明显的各向异性特征,渗流定向性随着节理角度变化显著;节理随着节理贯通性增加,节理渗透率呈现对数增加趋势;两组节理情况下,各向异性特征随着节理组间夹角变化;两组节理岩体渗流特征研究中,正交分布下,岩体仍存在各向异性,但渗流定向性系数较低;当节理倾角服从正态分布时,随着节理倾角标准差增大,渗透率增加;两组节理夹角不同时,节理渗透主方向倾角随着夹角增大而相应增大,基本沿两组节理夹角方向的角平分线方向。 相似文献
13.
A micromechanical model is proposed for studying the stability and failure process of slopes based on the gravity increase method (GIM). In this numerical model the heterogeneity of rock at a mesoscopic level is considered by assuming that the material properties conform to the Weibull distribution. Elastic damage mechanics is a method used for describing the constitutive law of the meso-level element, the finite element method (FEM) is employed as the basic stress analysis tool, and the maximum tensile strain criterion and the Mohr–Coulomb criterion are utilised as the damage threshold. The numerical model is implemented into the Realistic Failure Process Analysis (RFPA) code using finite element programming, and an extended version of RFPA, i.e., RFPA-GIM, is developed to analyse the failure process and stability of slopes. In the numerical modelling with RFPA-GIM, the critical failure surface of slopes is obtained by increasing the gravity gradually but keeping material properties constant. The acoustic emission (AE) event rate is employed as the criterion for slope failure. The salient feature of the RFPA-GIM in stability analysis of slopes is that the critical failure surface as well as the safety factor can be obtained without any presumption for the shape and location of the failure surface. Several numerical tests have been conducted to demonstrate the feasibility of RFPA-GIM. Numerical results agree well with experimental results and those predicted using the FEM strength reduction method and conventional limit equilibrium analysis. Furthermore it is shown that selection of the AE rate as the criterion for slope failure is reasonable and effective. Finally, the RFPA-GIM is applied to several more complex cases, including slopes in jointed rock masses and layered rock formations. The results indicate that the RFPA-GIM is capable of capturing the mechanism of slope failure and has the potential for application in a larger range of geo-engineering. 相似文献
14.
本文以土-岩接触面滑坡为工程背景，釆用中砂、硅粉、水泥等不同配合比材料，制成不同表面形状、不同抗压强度试件模拟岩石的表面凸起形状及风化程度，进行室内大型叠环单剪试验研究土石混合料与岩石接触面强度特性。结果表明:表面形状不同，土-岩接触面抗剪强度相差很大。表面起伏越大，抗剪强度越高，越接近土石混合料的抗剪强度。锯齿状(h=20 mm)＞锯齿状(h=10 mm)＞平直面(h=0)；同一起伏高度下，土-岩接触面抗剪强度表现为水波状＞阶梯状≈锯齿状＞单点凸起，但较起伏高度影响小。模拟岩石抗压强度不同反映岩石的风化程度不同，剪切过程中发生破损的程度就不同，破损使得土-岩接触面强度发生变化，岩石的风化程度是影响土-岩接触面抗剪强度的重要因素。综合分析岩石表面形状和风化程度对土-岩接触面抗剪强度特性的影响，引入结构面表面形状参数和损伤参数，给出土石混合料与岩石接触面的抗剪强度估算公式，为土-岩混合边坡的稳定性分析提供理论依据。 相似文献
15.
Barton剪切强度模型是目前工程实践中普遍采用的强度公式,而实践应用时,该模型中结构面粗糙性系数（JRC）的评估存在主观性和片面性的缺点。鉴于此,应用多重分形理论,提出了采用多重分形参数准确量化JRC的方法。首先应用数字图像处理技术获取了结构面三维形貌数据信息;然后采用投影覆盖法进行了结构面的分形维数计算,重点对结构面的多重分形特征进行了分析,通过对比分析了构造的15个结构面的多重分形特征值。结果表明：结构面越粗糙,多重分形特征参数 和 值越大, 或 能够很好地描述结构面的形貌特征。最后对9组石膏试件进行了剪切试验,通过不同正应力下对应的剪应力数据分析,结合结构面形貌多重分形参数 或 ,以Barton剪切强度公式为基础,应用最小二乘法原理,给出了JRC与 及JRC与 关系。这样在工程实际中,可以用参数 或 对JRC进行估算,克服了JRC人为估值主观性及采用二维标准轮廓线评估片面性的缺点,为准确评估结构面粗糙度提供了一条新的途径。在此基础上,应用Barton模型可准确估算岩体结构面的剪切强度。 相似文献
16.
The Planar Shape of Rock Joints 总被引：1，自引：1，他引：0
Knowing the planar shape of discontinuities is important when characterizing discontinuities in a rock mass. However, the
real discontinuity shape is rarely known, since the rock mass is usually inaccessible in three dimensions. Information on
discontinuity shape is limited and often open to more than one interpretation. This paper discusses the planar shape of rock
joints, the most common discontinuities in rock. First, a brief literature review about the shape of joints is presented,
including some information on joint-surface morphology, inferences from observed trace lengths on different sampling planes,
information based on experimental studies, and joint shapes assumed by different researchers. This review shows that joints
not affected by adjacent geological structures such as bedding boundaries or pre-existing fractures tend to be elliptical
(or approximately circular but rarely). Joints affected by or intersecting such geological structures tend to be rectangular.
Then, using the general stereological relationship between trace length distributions and joint size distributions developed
by Zhang et al. (Geotechnique 52(6):419–433, 2002) for elliptical joints, the effect of sampling plane orientation on trace lengths is investigated. This study explains why
the average trace lengths of non-equidimensional (elliptical or similar polygonal) joints on two sampling planes can be about
equal and thus the conclusion that rock joints are equidimensional (circular) drawn from the fact that the average trace lengths
on two sampling planes are approximately equal can be wrong. Finally, methods for characterizing the shape and size of joints
(elliptical or rectangular) from trace length data are recommended, and the appropriateness of using elliptical joint shapes
to represent polygonal, especially rectangular, joints is discussed. 相似文献
17.
Based on binocular stereo photography measurement technology, the actual distribution information of joints and fractures in the tunnel face were obtained via image processing and feature extraction, and the preliminary evaluation of surrounding rock stability of Laohushan tunnel was conducted according to surrounding rock classification method. Since all available surrounding rock classification approaches didn’t consider the influences of the size effect of tunnel excavation span and unfavorable geologic bodies such as weak-fracture zones, an improved discontinuous deformation analysis (DDARF) method was adopted to conduct a numerical simulation of the deformation and fracture processes of the surrounding rock. Using the traveling wave method, triangle DDA blocks were automatically generated in the calculation zone, and the block boundaries were divided into real joints and virtual joints. Based on the real joint information obtained via aforementioned photographic measurement, the real joints in the tunnel face were dynamically modified, in order to achieve the simulation of joint distribution. The results revealed that the fracture evolution regularity, deformation failure mechanism, and block dropping phenomenon that the DDARF joint simulation model calculated are in good agreement with actual conditions, while those obtained based on conventional models present differences from field situation. Additionally, focusing on the localised rockfall phenomenon of Laohushan tunnel, the crack extension rate was introduced to conduct a quantitative comparison of the rock crack evolution process with or without anchor supporting. The research results offer practical guidance for field construction and anchorage support scheme optimization. 相似文献
18.
Breakage of particles will have greatly influence on mechanical behavior of granular material(GM)under external loads,such as ballast,rockfill and sand.The discrete element method(DEM)is one of the most popular methods for simulating GM as each particle is represented on its own.To study breakage mechanism of particle breakage,a cohesive contact mode is developed based on the GPU accelerated DEM code-Blaze-DEM.A database of the 3D geometry model of rock blocks is established based on the 3D scanning method.And an agglomerate describing the rock block with a series of non-overlapping spherical particles is used to build the DEM numerical model of a railway ballast sample,which is used to the DEM oedometric test to study the particles’breakage characteristics of the sample under external load.Furthermore,to obtain the meso-mechanical parameters used in DEM,a black-analysis method is used based on the laboratory tests of the rock sample.Based on the DEM numerical tests,the particle breakage process and mechanisms of the railway ballast are studied.All results show that the developed code can better used for large scale simulation of the particle breakage analysis of granular material. 相似文献
19.
通过直剪条件下的模型试验研究具有相同连通率、含不同起伏角的共面闭合节理在不同法向应力作用下的剪切变形特征。试验结果表明：在达到峰值剪切强度前,剪切应力-位移曲线具有明显的线性段与非线性段;岩桥在法向与剪切荷载的共同作用下会产生一定程度的弱化,积累到一定程度时宏观表现为剪切应力软化。详细阐述了试验过程中裂纹发展的4个阶段并描述了剪切应力-剪切变形曲线变化的特征,提出一个能反映剪切应力-剪切变形曲线全过程的经验本构模型。新模型采用分段函数描述曲线变化特征。直剪试验数据分析表明,该模型能够拟合剪切应力-剪切变形变化发展趋势且具有较高的拟合精度,验证了模型的正确性。最后,对其存在的不足亦进行了简要分析 相似文献
20.
基于模拟退火算法的边坡稳定分析方法 总被引：7，自引：2，他引：5
岩石边坡开挖中存在大量的随机结构面,结构面与岩桥的组合破坏是边坡破坏的一种重要形式。如何确定抗剪强度最小的滑裂面是边坡工程中的重要研究方向。在岩体结构面调查统计基础上,运用随机网络模拟的方法得到边坡的裂隙网络图像,在此基础上应用模拟退火算法,搜索出边坡由结构面与岩桥组合形成的潜在最危险滑裂面的位置,将结构面组合滑动面与Sarma分析方法结合,形成一种改进的分析岩石边坡稳定性的方法--Sarma-SA分析法,通过一工程实例验证了该方法的合理性。 相似文献