共查询到20条相似文献，搜索用时 296 毫秒
1.
2.
Since cross-anisotropic sand behaves differently when the loading direction or the stress state changes, the influences of the loading direction and the intermediate principal stress ratio (b = (σ 2 ? σ 3)/(σ 1 ? σ 3)) on the initiation of strain localization need study. According to the loading angle (angle between the major principal stress direction and the normal of bedding plane), a 3D non-coaxial non-associated elasto-plasticity hardening model was proposed by modifying Lode angle formulation of the Mohr–Coulomb yield function and the stress–dilatancy function. By using bifurcation analysis, the model was used to predict the initiation of strain localization under plane strain and true triaxial conditions. The predictions of the plane strain tests show that the major principal strain at the bifurcation points increases with the loading angle, while the stress ratio decreases with the loading angle. According to the loading angle and the intermediate principal stress ratio, the true triaxial tests were analyzed in three sectors. The stress–strain behavior and the volumetric strain in each sector can be well captured by the proposed model. Strain localization occurs in most b value conditions in all three sectors except for those which are close to triaxial compression condition (b = 0). The difference between the peak shear strength corresponding to the strain localization and the ultimate shear strength corresponding to plastic limit becomes obvious when the b value is near 0.4. The influence of bifurcation on the shear strength becomes weak when the loading direction changes from perpendicular to the bedding plane to parallel. The bifurcation analysis based on the proposed model gives out major principal strain and peak shear strength at the initiation of strain localization; the given results are consistent with experiments. 相似文献
3.
Geotechnical experiments show that Lode angle‐dependent constitutive formulations are appropriate to describe the failure of geomaterials. In the present study, we have adopted one such class of failure criteria along with a versatile constitutive relationship to theoretically analyze the effects of Lode angle on localized shear deformation or shear band formation in loose sand for both drained and undrained conditions. We determine the variation in the possible stress states for shear localization due to the introduction of Lode angle by considering the localized deformation as a bifurcation problem. Further, similar bifurcation analysis is performed for the stress states along a specific loading path, namely, plane strain compression at the constitutive level. In addition, the plane strain compression tests have been simulated as a boundary value finite element problem to see how Lode angle affects the post‐localization response. Results show that the inclusion of a Lode angle parameter within the failure criterion has considerable effects on the onset, plastic strain, and propagation of shear localization in loose sand specimens. For drained condition, we notice early inception of shear localization and multiple band formation when the Lode angle‐dependent failure criterion is used. Undrained localization characteristics, however, found to be independent of Lode angle consideration. 相似文献
4.
为了研究层状千枚岩的力学特性与各向异性特征,开展了不同层理倾角与不同围压下的千枚岩力学试验。对比分析了千枚岩试样强度、变形、脆性与破坏模式等各向异性特征。结果表明:(1)随着层理倾角β增加,岩样的强度、变形特征曲线形状呈U型;随围压增加,岩样强度及塑性增强,各向异性度逐渐减弱稳定。(2)采用多种强度准则描述岩样强度各向异性,其中Saeidi准则和改进Ramamurthy准则能很好地预测岩样在不同层理倾角下的抗压强度。(3)基于岩样峰前应力-应变曲线与能量特征提出了综合脆性评价指标,在层理倾角β=45°左右时,岩样脆性指标较低,更易发生剪切滑移破坏,得出脆性下降顺序为:沿层理面拉伸劈裂>穿层理面拉伸劈裂>沿层理面剪切>穿层理面剪切。(4)千枚岩的破坏模式与层理倾角和围压有关,单轴条件下,岩样劈裂破坏后易形成复杂裂纹网络;高围压下,岩样破裂后多形成单一的沿层理面或贯穿多层理面的剪切破坏。 相似文献
5.
层状岩体单轴和双轴压缩蠕变特性的数值试验 总被引：1，自引：0，他引：1
以绿片岩和大理岩组成的层状岩体为研究对象,采用FLAC3D对互层状岩体进行了单轴和双轴压缩蠕变试验的数值分析,在数值分析中考虑荷载方向与层理之间的几何关系、大理岩夹层的体积分数、应力水平等的影响。研究结果表明:单轴和双轴压缩条件下,随着夹层倾角由0°增加至90°,轴向和夹层倾斜方向的应变绝对值均呈先增大后减小的变化规律;随着大理岩夹层体积分数的增加,轴向压缩变形和2个侧向方向的膨胀变形量均有所减小。单轴压缩条件下,当轴向荷载方向垂直于层理时,轴向压缩变形均大于轴向荷载方向平行于层理时的轴向压缩变形;双轴压缩条件下,当轴向荷载方向垂直于层理、侧向荷载方向平行于层理时,轴向压缩变形最大,当轴向荷载方向平行于层理、侧向荷载方向垂直于层理时,轴向压缩变形最小。 相似文献
6.
层状岩体抗剪强度具有各向异性的特点,在分析顺层岩质边坡的稳定性与剪切滑动面方向上需要考虑 值方向性变化的影响。首先提出层状岩体 值的表达式,然后在此基础上选用一顺层边坡作为实例,分别计算分析了坡高、岩层面倾角、坡顶堆载特别是强度参数 值各向异性对边坡稳定以及剪切面方向的影响。 相似文献
7.
为了研究粒状材料的各向异性力学行为与细观组构演化之间的关系,采用自主研发的双轴压缩试验系统,以圆形和椭圆形截面的金属棒状材料组成的二维堆积体为试验对象,对不同大主应力方向角?（沉积面与大主应力作用面的夹角）的试样进行了各向等压、常侧向压力、等p剪切3种应力路径试验,并通过分析试样在不同变形阶段的数字照片得到了其细观组构演化规律。发现对于椭圆形截面的试样存在一个卓越剪切方向,随剪应变增大,颗粒长轴呈现出向该方向偏转的趋势,并且在大变形条件下沿该方向形成剪切带;卓越剪切方向与沉积面方向关系不大,而与大主应力作用面方向夹角约为45°+ /2, 为残余内摩擦角;随卓越剪切方向与沉降方向夹角的不同,颗粒偏转程度的不同是导致剪胀特性和峰值强度各向异性的主要原因 相似文献
8.
对石英云母片岩进行三轴压缩蠕变试验,研究丹巴水电站石英云母片岩的三轴蠕变特性及其各向异性特性。按轴向荷载与层理面关系加工成平行组和垂直组2组试件,开展分级加载方式进行不同围压条件下的蠕变试验。试验研究表明,石英云母片岩具有蠕变特性,包括瞬时变形、衰减蠕变、稳定蠕变和加速蠕变阶段;采用带Kachanov蠕变损伤律的蠕变模型来描述石英云母片岩的蠕变特性,并进行蠕变参数辨识,拟合结果显示此模型能很好地描述石英云母片岩的蠕变特性;根据试验结果获得2组试件的长期屈服强度、破坏形态、瞬时变形参数和稳定蠕变速率,分析表明石英云母片岩的蠕变力学特性具有明显的各向异性特性。层理面与轴向荷载垂直的试件较层理面与轴向荷载平行的试件的强度、弹性剪切模量、体积模量和黏性系数相对较大,表现出较高的抗变形和抗破坏能力;平行组以剪切破坏为主,垂直组破坏时出现侧向鼓胀现象,显示出延性破坏的特点;2组石英云母片岩试件的瞬时应变量和稳定蠕变速率都随着应力水平的提高而增大。 相似文献
9.
10.
随着页岩气开采、废水回注和CO2地质封存工程活动的进行,储层应力环境改变诱发地震的问题得到广泛关注,研究储层岩石变形破裂和声发射规律对于理解诱发地震活动具有重要意义。本文选取了页岩、致密砂岩和白云岩开展三轴压缩声发射试验,获取了空间裂缝形态,揭示了不同类型储层岩石的变形破裂过程和声发射特征。结果表明:(1)页岩的扩容应力与峰值应力比最高,其次为白云岩和致密砂岩,表明页岩主要发生脆性破坏。(2)岩石结构对裂缝扩展和强度具有明显影响,页岩层理发育,抗压强度和裂缝形态各向异性显著。当层理角度为0°时,试样发生剪切-拉张复合型破坏。当层理角度为30°和60°时,试样主要发生剪切破坏。当层理角度增大至90°时,试样主要发生拉张破坏。致密砂岩破裂形成剪切主裂缝,白云岩形成两条剪切主裂缝和微裂缝。(3)不同类型储层岩石破裂过程声发射特征差异显著。页岩在扩容应力点附近有少量声发射活动,达到峰值应力时,声发射活动迅速增强。致密砂岩仅在破裂瞬间有少量声发射活动。相比之下,白云岩在裂缝非稳定扩展阶段和峰后阶段声发射活动显著。因此,在工程实践中需要根据微震监测调整施工措施,避免页岩作为储盖层发生脆性破坏和白云岩储层改造诱发地震。 相似文献
11.
处于薄—中层倾斜层状岩体中的深埋隧道常会产生地质顺层偏压的问题,导致隧道局部塌方、偏压变形及支护结构破坏。本文以郑万线某隧道为例,采用理论分析、数值模拟方法对深埋顺层隧道的破坏机理及不同结构面参数下的破坏规律展开了研究。研究结果表明:（1）深埋顺层偏压隧道洞周围岩将根据其切向应力与结构面夹角的不同发生岩层拉裂破坏、结构面剪切破坏及岩体自身破坏,其中切向应力与结构面平行位置,即反倾侧拱腰及顺倾侧拱脚位置主要发生拉裂破坏,此处围岩塑性区范围最广,围岩位移最大,围岩处于极不稳定状态;（2）顺层偏压隧道的破坏规律与结构面强度参数有直接关系,围岩塑性区范围及围岩位移均随着结构面摩擦角的增大而降低,且降低趋势逐渐放缓,当结构面摩擦角达到岩体摩擦角后,结构面摩擦角继续增加对围岩稳定性影响较小;（3）围岩塑性区及围岩位移场偏压分布特征随结构面倾角的变化而整体旋转,且对于隧道底部而言,结构面最不利倾角为0°,此时隧底最大上鼓量大于其他倾角下的最大上鼓量;对于隧道拱部而言,最不利倾角为40°,此时洞周最大收敛值大于其他倾角下的最大收敛值,最不利位置位于反倾侧拱腰。 相似文献
12.
压缩作用下岩石内部细观裂纹扩展导致岩石产生损伤,其对岩石变形、强度等力学特性有着重要影响;然而,岩石内部裂纹扩展与剪切特性（黏聚力、内摩擦角及剪切应力）动态演化关系很少被研究。基于裂纹扩展机制推出的岩石应力-应变本构模型,并结合摩尔-库仑失效准则,推出了在岩石应力-应变关系峰值应力（对应岩石压缩强度）状态时,本构模型细观力学参数与岩石黏聚力、内摩擦角及剪切强度之间的状态关系。然后,引入岩石应力-应变本构关系塑性变形阶段服从摩尔-库仑屈服准则的力学流动规律,进而将已推出的应力-应变关系峰值状态点所满足的细观力学参数与黏聚力、内摩擦角关系,推广到岩石进入塑性变形后,岩石内部裂纹扩展（或应变）与黏聚力、内摩擦角及剪切应力动态演化的理论关系。随着裂纹扩展或应变增加,黏聚力、内摩擦角及剪切应力先增大,达到一个峰值点后减小,该结果与应力-应变本构曲线变化趋势相对应。通过试验结果验证了所提出理论结果的合理性。并讨论了初始裂纹之间摩擦系数对黏聚力、内摩擦角及剪切应力随裂纹扩展或应变演化规律的影响。 相似文献
13.
Properly accounting for the mechanical anisotropy of shales can be critical for successful drilling of high inclination wells, because shales are known to be weak along bedding planes. To optimize the drilling parameters in such cases, a sufficiently representative, anisotropic rock mechanical model is therefore required. This paper presents such a model developed to better match results from a dedicated, extensive set of uniaxial and triaxial compression tests performed on plugs of Mancos outcrop shale with different orientations relative to the bedding plane. Post failure inspection of the plugs shows that the failure planes are to some extent affected by the orientation of the applied stress relative to the bedding planes, indicating that the bedding planes may represent weak planes which tend to fail before intrinsic failure occurs, whenever the orientation of these planes is suitable. The simple “plane of weakness” model is commonly used to predict strength as function of orientation for such a rock. A comparison of this model to the experimental data shows, however, that the weak planes seem to have an impact on strength even outside the range of orientations where the model predicts such impact. An extension of this model allowing the weak planes to be heterogeneous in terms of patchy weakness was therefore developed. In this model, local shear sliding may occur prior to macroscopic failure, leading to enhanced local stresses and corresponding reduction in strength. The model is found to give better match with strength data at intermediate orientations. The model is also able to partly predict the qualitatively different variation of Young’s modulus with orientation for this data set. 相似文献
14.
The inelastic response of Tennessee marble is modelled by an elastic plastic constitutive relation that includes pressure dependence of yield, strain‐softening and inelastic volume strain (dilatancy). Data from 12 axisymmetric compression tests at confining pressures from 0 to 100 MPa are used to determine the dependence of the yield function and plastic potential, which are different, on the first and second stress invariants and the accumulated inelastic shear strain. Because the data requires that the strain at peak stress depends on the mean stress, the locus of peak stresses is neither a yield surface nor a failure envelope, as is often assumed. Based on the constitutive model and Rudnicki and Rice criterion, localization is not predicted to occur in axisymmetric compression although faulting is observed in the tests. The discrepancy is likely due to the overly stiff response of a smooth yield surface model to abrupt changes in the pattern of straining. The constitutive model determined from the axisymmetric compression data describes well the variation of the in‐plane stress observed in a plane strain experiment. The out‐of‐plane stress is not modelled well, apparently because the inelastic normal strain in this direction is overpredicted. In plane strain, localization is predicted to occur close to peak stress, in good agreement with the experiment. Observation of localization on the rising portion of the stress–strain curve in plane strain does not, however, indicate prepeak localization. Because of the rapid increase of mean stress in plane strain, the stress–strain curve can be rising while the shear stress versus shear strain curve at constant mean stress is falling (negative hardening modulus). Copyright © 2001 John Wiley & Sons, Ltd. 相似文献
15.
Pipatpongsa Thirapong Fang Kun Leelasukseree Cheowchan Chaiwan Apipat 《Landslides》2022,19(8):1861-1879
A stability analysis of a laterally confined slope model, lying on an inclined bedding plane, was presented to evaluate the lateral shear resistance by considering the loading paths and failure envelopes. Two slope models were prepared on a bedding plane by compaction, one with and one without lateral confinement. The compacted models are related to the geological conditions at shallow depths where brittle deformation can occur and an excavation can induce horizontal field stress that significantly influences the stability of the slope. Three distinct loading paths, controlled by either tilting the angles or increasing the surcharge loads, were applied to achieve the failure of the slope models. Rankine’s passive earth pressure due to compaction was reduced by the shear strength reduction ratio. The shear strength reduction ratio was estimated through the least-squares fitting method based on the results of model tests at failure when the loading paths intersected the failure envelope. Provided that the effect of lateral confinement in a rock mass can be described by the shear strength reduction ratio, the proposed equations will be beneficial for slope stability analyses of laterally confined slopes on bedding planes. A case study of an undercut pit wall in an open-pit mine was demonstrated by showing that the unknown shear strength reduction ratio can be back-analyzed from the rainfall-induced landslide case. Therefore, the design of other undercut slopes with different geometries and groundwater conditions in the rock mass, which have undergone the same geological process as the back-analyzed case, is possible.
相似文献16.
节理岩体的剪切特性是主导岩体工程稳定性的关键因素。基于PFC2D离散元颗粒流程序,结合室内试验结果对比分析,选取合理的细观参数进行数值模拟,分别从细观角度研究了节理岩石的裂纹发展、能量转化及声发射现象等特性,从宏观角度研究了节理岩石的强度模型和破坏形态。结果表明：节理岩体主要呈现磨损和剪断两种破坏形态,不同的破坏形态对应不同的强度模型;随着剪切变形增加,岩体沿节理面发生破坏,弹性阶段以法向裂纹为主,而塑性阶段切向裂纹起主导作用,滑移区R、P裂纹贯通形成破碎带,节理面产生较大滑移;在应力达到峰值强度前,边界能主要转化为应变能,法向裂纹生成较多;越过峰值强度后,摩擦能快速增长,并伴随大量切向裂纹产生。与室内试验结果相比,PFC2D较好地模拟了节理岩体剪切力学特性,弥补了室内试验中无法进行细观特性研究的缺陷,对于节理岩体后期研究提供了一些参考。 相似文献
17.
为研究鄂西北地区板岩的力学特性及各向异性特征,开展了志留系粉砂质板岩的单轴压缩和巴西劈裂试验,分析了试样的力学特性和各向异性特征以及在不同荷载作用下的变形破坏模式,揭示了不同破坏模式的力学机制,并通过数值分析研究了不同板理面角度板岩边坡破坏模式及力学机制。研究结果表明,粉砂质板岩中的板理面是影响岩体力学行为的弱面,使得粉砂质板岩表现出明显的各向异性的特征。在单轴压缩条件下,粉砂质板岩在垂直板理面方向比平行板理面方向更易变形,变形量更大;平行板理面方向加载时试样破坏类型为竖向劈裂型张拉破坏,其实质是压杆失稳;垂直板理面加载时试样的破坏类型为穿切板理面的劈裂型剪切破坏;所测得的力学参数各向异性也较明显。在劈裂荷载作用下,粉砂质板岩的破坏模式主要有张拉劈裂破坏和沿板理面剪切破坏两种,所得抗拉强度在平行板理面方向上最大,在垂直板理面方向上最小,两个方向上的抗拉强度均小于抗压强度。由于板理面间的抗拉强度极低,在受到与板理面呈小角度相交的劈裂荷载作用时,容易产生沿板理面的张拉劈裂或拉剪破坏,在实际工程中应尽量避免板理面间的受拉破坏和沿板理面的拉剪破坏。在边坡工程中,板理面倾向、倾角对边坡破坏模式及力学机制有较大影响,边坡防护治理需充分考虑这一影响。上述研究为粉砂质板岩区岩质边坡防护治理以及其他岩石工程设计与施工提供理论依据与技术基础。 相似文献
18.
Strain localization developing inside soft rock specimens is examined through experimental observation and numerical simulation. In the experimental study, soft rock specimens are sheared at different strain rates under plane strain conditions and deformation and strain localization characteristics are analysed. Transition of localization mode from highly localized mode for higher strain rate to distributed and diffused mode of strain localization for lower strain rates was observed. In the numerical study, simulations of plane strain compression tests are carried out at different strain rates by using an overstressed‐type elasto‐viscoplastic model in finite element computations. The role of strain rates on setting gradients of strain fields across shear band is clarified. The probable mechanism for transition of localization mode is discussed. Copyright © 2005 John Wiley & Sons, Ltd. 相似文献
19.
基于不同层理角度的页岩巴西劈裂试验,利用高速摄像系统和声发射系统,对页岩力学特性、裂纹扩展及声发射特征的层理效应进行了深入研究。结果表明：（1）页岩巴西劈裂破坏过程可以分为压密、弹性和破坏3个阶段;（2）页岩抗拉强度、劈裂模量和应力峰值时变形的各向异性特征明显,层理角度 30°时,层理效应最为明显, 90°时影响最小;（3） 0°和 15°时试样的裂纹破坏面基本是沿着层理面, 30°时裂纹面交切层理面,与加载基线面重合, 45°～90°的各试样的断裂面呈不同程度的偏离加载基线面,为弧面或曲面;（4） 30°和 45°为破坏机制转化角,其中 30°为沿着层理面压致性张拉开裂转化为交切层理面开裂的转化角, 45°为交切层理面开裂转化为交切层理面且沿着层理面不同程度的剪切滑移开裂的转化角;（5）声发射活动性和能量释放随层理角度的增加而加强,主要因为受层理角度的影响,其破坏机制不同,这也进一步验证了页岩随层理角度的变化,其破坏机制的各向异性。能率峰值与抗拉强度具有很好的线性关系,表明声发射能率峰值能很好地反映岩石抗拉伸破坏的程度。 相似文献
20.
Size and strain rate are two key factors that dramatically influence the estimation of rock mechanical behaviors. To better understand the effects of size and strain rate on measured rocks, rock specimens with six different sizes were tested at six different strain rates under uniaxial compression using the MTS 815 Rock Mechanics Test System. Having determined that the size and strain rate significantly affect the peak strain, peak stress, elastic modulus, acoustic emission (AE), and failure pattern of the rock specimens, the relation was established between the strength and the size and strain rate of red sandstone. And the variation was revealed among the size and strain rate, the AE, and the failure pattern. It turned out that the peak stress was negatively correlated with the rock size and was positively correlated with the strain rate. When the length to diameter ratio (L/D) of the rock specimen was less than 2.0, the AE appeared mildly. The AE quantities gradually increased before the peak stress, and then sharply decreased after the peak stress. The failure pattern of the rock specimen was relatively complicated, with a fracture plane appearing along the axial direction. Conical failure type was also presented. When the L/D ratio of the specimen was greater than 2.0, the AE characteristics of red sandstone showed the radical model. There were relatively few AE rings before the peak stress. But the AE rings increased suddenly and dramatically during the peak stress. The rock specimens primarily failed with a single shear plane. Moreover, with an increase in the strain rate, the AE activities were enhanced and the AE quantities increased. When the strain rate of the rock specimen was less than 5.0?×?10?4/s, the rock specimen failed with a shear or tensile-shear pattern. And when the strain rate was greater than 5.0?×?10?4/s, the rock specimen tended to fail in a conical pattern. 相似文献