共查询到20条相似文献，搜索用时 562 毫秒
1.
We describe recent mechanical andeelectronic modifications to the Cambridge Ocean Bottom Hydrophone system, enabling it to record in addition three geophone channels from a deployed, disposable geophone package. Examples of data from seismic refraction experiments show good correspondence between records of ground motion detected by the hydrophone and the vertical geophone. Seismic signals are undistorted by noise from instrument related sources. Clear examples of P to S conversions just below the receiver are observed. Improved recording conditions are achieved by deploying the geophones in a small pressure vessel as far away as possible from the main instrument package. 相似文献
2.
Félix Avedik Vincent Renard Didier Buisine Jean-Yves Cornic 《Marine Geophysical Researches》1978,3(4):357-379
This paper describes a pop-up ocean bottom seismograph designed primarily for refraction surveys both on the continental shelf and in deep sea. Its development is the extension of our system based on seismic detectors located on the sea floor with radio transmission of seismic signals and used for seismic refraction studies on the continental shelf. The seismic detectors (vertical geophone or hydrophone and two orthogonally mounted horizontal geophones) are located outside of the pressure vessel on the main frame. Optionally, the seismic sensors may be decoupled from the main frame assembly. This decoupling is performed by a mobile arm positioning the separate three component sensor package on the sea floor.Contribution No. 455 of the Département Scientifique, Centre Océanologique de Bretagne. 相似文献
3.
The often poor quality of ocean bottom seismic data, particularly that observed on horizontal seismometers, is shown to be the result of instruments responding to motions in ways not intended. Instruments designed to obtain the particle motion of the ocean bottom are found to also respond to motions of the water. The shear discontinuity across the ocean floor boundary results in torques that cause package rotation, rather than rectilinear motion, in response to horizontal ground or water motion. The problems are exacerbated by bottom currents and soft sediments. The theory and data presented in this paper suggest that the only reliable way of obtaining high fidelity particle motion data from the ocean floor is to bury the sensors below the bottom in a package with density close to that of the sediment. Long period signals couple well to ocean bottom seismometers, but torques generated by bottom currents can cause noise at both long and short periods. The predicted effects are illustrated using parameters appropriate for the operational OBS developed for the U. S. Office of Naval Research. Examples of data from ocean bottom and buried sensors are also presented. 相似文献
4.
Dessureault J.-G. Belliveau D.J. Young S.W. 《Oceanic Engineering, IEEE Journal of》1991,16(4):397-401
A package designed to protect an RD Instrument Ltd. acoustic Doppler current profiler survived several passages of a bottom trawl. The package, in the shape of a truncated pyramid, has a base 4 m by 3.3 m and a height of 53 cm. The authors describe the package, its deployment method, and field test results where a trawl was repeatedly dragged over the unit. The device has been used successfully three times on the continental shelf. Some acoustic measurements were also made to ascertain the effect of the package on the beam pattern. The results show that this design can protect the instrument from bottom trawls and the acoustic beams are minimally affected by the plastic plate in front of the instrument transducers 相似文献
5.
A simple shaker table for seismometer calibration 总被引：1，自引：0，他引：1
Frederick K. Duennebier George H. Sutton David Harris David A. Byrne 《Marine Geophysical Researches》1984,6(3):311-328
A unique and simple shaker table (shake table or shaking table), designed, constructed, and installed at the Hawaii Institute of Geophysics, has proven to be a valuable aid in testing and calibrating short period seismometers, as well as ocean bottom and ocean sub-bottom seismometer/tilt meter packages. It consists of a platform suspended in a stairwell by a single elastic cord (10 m extended length) driven by GeoSpace HS-10 geophones. Platform motion is monitored by orthogonal reference geophones and tilt meters. The relatively low natural periods of the platform, about 1.9 sec vertical and 6.5 sec horizontal, provide sufficient isolation from local vibrations that calibration can be made near operational amplitudes. Vertical or horizontal driver geophones can be driven by a commercial signal generator or white noise generator, or from magnetic tape output. The table can also be tilted with respect to the drivers to determine tilt tolerances and to calibrate tilt meters. A Hewlett-Packard 3582-A spectrum analyzer, used to analyze both reference and output signals, provides near real-time system cabibration and is an efficient means for investigating parasitic system resonances. The analyzer can also provide a white noise signal source to the driver geophones.Hawaii Institute of Geophysics Contribution 1443. 相似文献
6.
A three-component pop-up ocean-bottom seismograph was built at the Institute of Oceanographic Sciences in 1978. It is constructed around a buoyant 71 cm diam aluminium alloy forged sphere which contains three 4.5 Hz orthogonal geophones and an external hydrophone. The instrument will record continuously in analogue mode for over eight days using a modified reel-to-reel tape-recorder running at 1.5 mm s-1. The geophones have a bandwidth of 2–25 Hz and the hydrophone bandwidth is 5–40 Hz. Ballast release is by pre-set clock or by acoustic command.Fifty-four deployments have been carried out in five cruises for the loss of only one instrument. Good recordings of dropped weights, airguns, explosions and earthquakes have been obtained. 相似文献
7.
The Ocean Bottom Seismometer (BOBS) designed and built at BIO is described. The instrument is small, easy to handle and has performed reliably. Signals from two geophones and one hydrophone are recorded continuously for up to 10 days. A microcomputer is used as the clock and control.An account of past use, and future plans is given. 相似文献
8.
The MIT ocean-bottom seismometer is a free-fall, pop-up instrument capable of recording three components of seismic data on the sea floor for periods of at least one month. Data are recorded in digital format on a specially designed magnetic tape recorder. An event recording scheme and semiconductor memories assure both efficient data storage and preservation of first motion information. Sensors and recording electronics are housed in a cylindrical pressure vessel, which sits vertically atop an expendable base plate on the ocean bottom. Attached to the pressure case are three glass spheres for buoyancy. After a pre-set time interval, a motor-driven mechanical latch release frees the instrument to float to the ocean surface for recovery. 相似文献
9.
A pop-up bottom seismic recorder designed for seismic refraction experiments was built by the Institute of Oceanographic Sciences in 1968. The device is housed within a 71 cm diameter sphere weighing 270 kg when launched. signals picked up by a hydrophone are recorded in analogue form on magnetic tape in the band 2–100 Hz. The total continuous recording period is 12 hr but the lifetime of the system can be effectively extended by cycling the tape-recorders to allow shooting to go on for up to 3 days. Ballast release is by acoustic command or by pre-set clock. The instruments have been used in water depths from 150 to 4820 m making a total of 63 deployments with a 95% recovery rate. A new version with three-component geophones is being built. 相似文献
10.
A series of transient tests were conducted to determine the seafloor coupling characteristics of a new ocean-bottom seismometer (OBS) developed for the United States Office of Naval Research (ONR). The OBS comprises a large recording package and a separate sensor package that is deployed from the recording package. In addition to the coupling characteristics of both the sensor and the recording packages, the seismic energy radiated from the main recording package as a result of motion of the recording package was measured. The observed vertical coupling resonances of both the recording package and the sensor package are in good agreement with those predicted by a simple model of soil-structure interaction. The most important result of this study is that significant energy is radiated from the recording package in response to horizontal motions of the recording package. When the sensor package is 1 m from the recording package, the amplitude of the recorded signal is similar to that recorded in the recording package. In the field, this effect will result in distortion of seismic signals and increased background noise recorded by the sensor package if the recording package is disturbed by seafloor currents or biological activity. The amplitude of this signal attenuates by approximately a factor of two as sensor/recorder separation is increased from 1 to 6 m, suggesting that an improved response can be achieved by increasing the separation between the recording package and the sensors. This effect is much less severe for vertical disturbances of the recording package. 相似文献
11.
Data from the 1978 Lopez Island OBS Intercomparison Experiment and deep sea data from University of Washington OBSs show that there is a considerable amount of waveform distortion resulting from the conversion of horizontal motion into vertical motion, here called cross-coupling distortion. This distortion, which substancially reduces the significance of waveform matching with synthetic seismograms, appears to result from rotation imparted to the OBS package by near-vertically traveling shear energy. The degree of this rotation seems to depend on the instrument surface area above the seafloor and the geometry and surface area of the feet connecting the package to the seafloor. The sensitivity and response of the seismometers within the package to this rotation depends on the precise location of the seismometers with respect to the axis of rotation. The results suggest how to modify OBS designs to minimize these effects.University of Washington Contribution No. 1225. 相似文献
12.
Timothy W. Barash Charles G. Doll Jr. John A. Collins George H. Sutton Sean C. Solomon 《Marine Geophysical Researches》1994,16(5):347-363
A problem in the use of ocean bottom seismometers is the difficulty in leveling the sensors while ensuring good coupling to the seafloor. We have investigated the coupling characteristics of the seismic sensors in the new ONR ocean bottom seismometer. In the deployable sensor package for that instrument, a three-component seismometer set is suspended on a 2-axis passive leveling gimbal and is immersed in a viscous fluid. We report tests, conducted in a seismic vault, comparing the output of a gimbaled seismometer set to that of a set rigidly coupled to the ground. Our results show that the degree to which the gimbaled set is coupled to ground motion is a function of the viscosity of the coupling fluid. The coherence between the two sensor sets is poor (<0.4) at some frequencies within the band of interest (0.15 to 20 Hz) and on some components when the viscosity of the coupling fluid is comparatively low (14 Pa-s or 0.16 kSt kinematic viscosity). In addition, the outputs of some components over portions of this frequency band are attenuated and are phase-shifted relative to the outputs of the set rigidly coupled to the ground. Coherence and phase response similarity improve as the viscosity of the coupling fluid is increased. With a coupling fluid viscosity of 980 Pa-s (10 kSt), coherence and phase agreement between the two sensor sets is good (>0.9) across nearly the entire band of interest on all three components. A simple analytical model of the gimbaled seismometer set as a damped, driven, compound-pendulum provides a basis for understanding the test results. 相似文献
13.
David Harris Robert K. Cessaro Fred K. Duennebier David A. Byrne 《Marine Geophysical Researches》1987,9(1):67-94
The Hawaii Institute of Geophysics began development of the Ocean Subbottom Seisometer (OSS) system in 1978, and OSS systems were installed in four locations between 1979 and 1982. The OSS system is a permanent, deep ocean borehole seismic recording system composed of a borehole sensor package (tool), an electromechanical cable, recorder package, and recovery system. Installed near the bottom of a borehole (drilled by the D/V Glomar Challenger), the tool contains three orthogonal, 4.5-Hz geophones, two orthogonal tilt meters; and a temperature sensor. Signals from these sensors are multiplexed, digitized (with a floating point technique), and telemetered through approximately 10 km of electromechanical cable to a recorder package located near the ocean bottom. Electrical power for the tool is supplied from the recorder package. The digital seismic signals are demultiplexed, converted back to analog form, processed through an automatic gain control (AGC) circuit, and recorded along with a time code on magnetic tape cassettes in the recorder package. Data may be recorded continuously for up to two months in the self-contained recorder package. Data may also be recorded in real time (digital formal) during the installation and subsequent recorder package servicing. The recorder package is connected to a submerged recovery buoy by a length of bouyant polypropylene rope. The anchor on the recovery buoy is released by activating either of the acoustical command releases. The polypropylene rope may also be seized with a grappling hook to effect recovery. The recorder package may be repeatedly serviced as long as the tool remains functionalA wide range of data has been recovered from the OSS system. Recovered analog records include signals from natural seismic sources such as earthquakes (teleseismic and local), man-made seismic sources such as refraction seismic shooting (explosives and air cannons), and nuclear tests. Lengthy continuous recording has permitted analysis of wideband noise levels, and the slowly varying parameters, temperature and tilt.Hawaii Institute of Geophysics Contribution 1909. 相似文献
14.
TenCate J.A. Muir T.G. Caiti A. Kristensen A. Manning J.F. Shooter J.A. Koch R.A. Michelozzi E. 《Oceanic Engineering, IEEE Journal of》1995,20(4):300-310
The problem of locating very low frequency sound sources in shallow water is made difficult by the interaction of propagating acoustic waves with the sea floor. Slow wave speeds and the attendant short wavelengths suggest that low frequency beamforming and source localization with sea floor geophones can be accomplished with relatively small arrays when compared with hydrophone arrays in the water column. To test the feasibility of this approach, experiments were carried out in the shallow water of the Malta Channel of the Straits of Sicily where the Scholte wave speed was some 10 to 20 times slower that the speed of sound in water. A linear array of ten vertically gimballed geophones was deployed and measurements were made on propagating seismic wave fields generated by explosive shots. The resulting directivities, beam patterns, and sidelobe characteristics are in excellent agreement with array theory, which suggests that coherent processing is a viable technique on which to base new applications for seismic arrays on the sea floor. Supporting materials on the geophysics of Scholte waves and calculations of the wave field at the site are presented 相似文献
15.
W. G. McDonald A. C. Hubbard R. G. Bookbinder K. McCamy 《Marine Geophysical Researches》1977,3(2):179-196
Ocean bottom seismographs designed to meet the requirements of both seismicity and refraction experiments have been operated extensively on twelve cruises (72 deployments). Signals from a hydrophone, and two geophones (horizontal and vertical) are direct recorded on a modified commercial tape recorder providing 10 day continuous recording at 1/40 ips and a 2–80 Hz band width. The free-fall deployment technique with timed ballast release has yielded a 93% recovery rate (96% over the most recent 24 deployments) despite frequently difficult weather and sea conditions. Emphasis on reliability and operational simplicity has produced an instrument that can be operated in arrays by a single shipboard technician.Lamont-Doherty Geological Observatory Contribution Number 2535. 相似文献
16.
Instrument calibration of ocean bottom seismographs 总被引：1，自引：0，他引：1
To increase the accuracy of measuring sea floor motion with ocean bottom seismometers, we calibrate the seismometer system on the ocean floor. Data from the sea floor calibration, augmented with electronic and land calibration data, enables us to find the OBS transfer function to an accuracy of 0.5% in the frequency range of 0.1 to 32 Hz. We are able to distinguish between temperature, instrument and OBS ground coupling effects, all of which alter the transfer function. This paper reviews our method of calibration and discusses the effects of temperature and some of the instrument design features on the vertical seismometer transfer function. 相似文献
17.
数字检波器在地震勘探中的应用效果 总被引：3，自引：0，他引：3
随着地震勘探精度的要求和发展,对地震仪器和检波器的要求也不断提高,只有接收到来自地下的有效反射信号,尤其是深层的高频弱反射信号,才能通过室内处理达到提高勘探精度的目的。数字检波器具有直接输出数字、高保真矢量场、感应器倾斜校正等特点,其动态范围与目前最先进的地震仪器相匹配,对来自地下的地震波没有改造,真实地记录了地震波的特性。针对数字检波器的特性进行了系统试验,通过试验效果分析认为:在信噪比方面,单个数字检波器与单个普通检波器无明显的差别,但单个数字检波器的信噪比明显低于多个普通检波器组合的信噪比;在能量方面,单个数字检波器的能量相当于多个普通检波器组合的能量;在频率方面,教字检波器比普通检波器的频带宽,可以预测,数字检波器将广泛地应用于高分辨率地震勘探中。 相似文献
18.
Christine M. R. Powell Martin C. Sinha Peter W. Carter John R. Leonard 《Marine Geophysical Researches》1986,8(3):277-292
The PUMA (Pull-Up Multichannel Array) is a sea-bottom instrument for remotely recording data from a 12 channel hydrophone array. Its purpose is to achieve (i) denser data coverage, leading to (ii) improved velocity analysis and (iii) multichannel processing of wide angle seismic data collected on the continental shelf. The instrument consists of a 1.2 km array terminating with a pressure case in which 8 FM cassette recorders, a power supply, microprocessor controller and internal clock are housed. It can be pre-programmed to switch on during shot windows for a total of four hours recording time.The PUMA was successfully used in an experiment west of Lewis, Outer Hebrides, U.K. in August–September 1984. We show an example of PUMA data from this experiment. Indications are that the instrument will provide improved constraints on seismic velocities in the lower continental crust and uppermost mantle. 相似文献
19.
Abstract The Canadian program for obtaining hydrographic data by aerial methods consists of merging laser bathymeter data with photogrammetric depth data. The main deficiency of the photogrammetric approach for bathymetric measurements is that incomplete stereomodels can occur in areas where little or no land appears. This problem is overcome by using an inertial navigation system (INS) hardmounted to the aerial camera to provide the orientation parameters of position and attitude for each photograph. In order to meet the high accuracy requirement, the INS and other complementary navigation data are processed through a post‐mission track recovery software package. The photogrammetric depths are improved further by merging them with the waterline height information and the laser bathymeter depths using a least‐squares adjustment algorithm. The photogrammetric compilation, depth measurements, shoreline plots, and laser bathymeter integration is done in an analytical stereoplotter. This instrument provides an on‐line refraction correction necessary because of the two‐media mode of operation. Results of a recent pilot project indicate that the integrated system is capable of obtaining depth measurements that agree with echo sounder depth measurements to a precision of .65 m (RMS), and that it can position measured depths to a precision of .74 m (RMS) relative to local control. 相似文献
20.
Ocean bottom seismometers (OBS) have been widely used during the past decade to collect seismic data for determination of the structure of the oceanic lithosphere, stress patterns in regions of earthquake activity, and geoacoustic parameters of the ocean floor. Data quality from these experiments has often been disappointing because of poor signal quality and high noise levels. Many of these problems result from motion of the OBS package that is decoupled from motion of the ocean floor. These coupling problems are more serious in the ocean than on land because of the low shear strengths of most ocean sediments. In this paper we continue to develop the theory of coupling of OBSs to soft sediments and arrive at results suggesting that OBS packages should be designed with: (1) the minimum mass possible, (2) radius of area in contact with the sediment proportional to the cube root of the mass, and the maximum radius less than 1/4 of the shear wavelength, (3) density of the OBS approximately that of the sediment, (4) a low profile and a small vertical cross section with water, and (5) low density gradients, and maximum symmetry about the vertical axis. Agreement of the theory with test data is good; most deviations are reasonable, given limitations of the theory and experiments. The theory also suggests that the coupling frequency, the frequency above which the OBS does not follow the motion of the sediment, is directly proportional to the sediment shear velocity. 相似文献