共查询到20条相似文献，搜索用时 31 毫秒
1.
Reinforcement and Arching Effect of Geogrid-Reinforced and Pile-Supported Embankment on Marine Soft Ground 总被引：1，自引：0，他引：1
The effectiveness of constructing a geogrid-reinforced and pile supported embankment on soft ground to reduce differential settlement has been studied by pilot scale field tests and numerical analysis. Three-by-three pile groups with varying pile spacing were driven into a layer of soft ground, and a layer of geogrid was used as reinforcement over each pile group. Further, a 2-D numerical analysis has been conducted using the computer program FLAC 2D. The mechanisms of load transfer can be considered as a combination of embankment soil arching, geogrid tension, and stress transfer due to the difference in stiffness between pile and soft ground. Based on the pilot scale field tests and results of numerical analysis, we find that the geosynthetic reinforcement slightly interferes with soil arching, and helps reduce differential settlement of the soft ground. Also, the most effective load transfer and vertical stress reduction at the midspan between piles occurs when the pile cap spacing index D/b (D: pile cap spacing, b: diameter of pile) is 3.0. 相似文献
2.
The effectiveness of constructing a geogrid-reinforced and pile supported embankment on soft ground to reduce differential settlement has been studied by pilot scale field tests and numerical analysis. Three-by-three pile groups with varying pile spacing were driven into a layer of soft ground, and a layer of geogrid was used as reinforcement over each pile group. Further, a 2-D numerical analysis has been conducted using the computer program FLAC 2D. The mechanisms of load transfer can be considered as a combination of embankment soil arching, geogrid tension, and stress transfer due to the difference in stiffness between pile and soft ground. Based on the pilot scale field tests and results of numerical analysis, we find that the geosynthetic reinforcement slightly interferes with soil arching, and helps reduce differential settlement of the soft ground. Also, the most effective load transfer and vertical stress reduction at the midspan between piles occurs when the pile cap spacing index D/b (D: pile cap spacing, b: diameter of pile) is 3.0. 相似文献
3.
AbstractPipes buried in soft ground can be damaged due to the vertical and lateral movement of the ground during the construction of the embankment. To investigate such a movement of the soft ground, full-scale tests using embankment piles and stabilizing piles were conducted for 70?days. A pile-supported embankment has been used to reduce the deformation of soft ground by transferring the embankment load through piles to the firm layer below the soft ground, whereas stabilizing piles have been employed to resist the lateral earth pressure that is induced in soft ground by embankment loads. The Coupling Area (CA), which was defined as the quantitative index to determine the resistance effect of both settlement and lateral flow of the soft ground when the embankment was reinforced, is adapted. The analysis results of the CA indicate that the piled embankment was more effective for preventing the damage to buried pipe installed near the embankment, while the stabilizing piles had almost the same effect as the piled embankment when the pipe was buried far away from the embankment. 相似文献
4.
Won Pyo Hong 《Marine Georesources & Geotechnology》2017,35(5):719-729
Lateral flow of soft ground occurs when embankment filling is performed on reclaimed land of foreshore. If a utility pipe is buried in soft ground undergoing the lateral flow, severe damage to the pipe can be caused. A pile-supported embankment has been used to support embankment to minimize lateral flow of the soft soil by transferring the embankment loads through the piles to the firm layer. To prevent damage to the buried pipe subjected to lateral force of the soft ground, full-scale field experiments on the piled embankment were conducted for 70 days. The test results show that the piled embankment effectively reduces both the settlements of the ground and the lateral displacements of the buried pipe. Although additional load was not imposed on the embankment after finishing embankment filling, the settlement and lateral displacement of soft ground simultaneously increased. This coupling behavior was observed at the toe of the embankment and the back of the buried pipe. To quantitatively evaluate the coupling effect of the movement, the coupling area (CA) was coined and analyzed with the efficiency of load transfer. The efficiency evaluated by the CA was in good agreement with the efficiency by the soil arching mechanism. 相似文献
5.
Jun Chen Zhen-Yu Yin Ye-Shuang Xu Suksun Horpibulsuk 《Marine Georesources & Geotechnology》2016,34(5):420-430
This article presents a case history of determination of effective depth of prefabricated vertical drains (PVDs) under embankment loading on a very soft clay deposit in central China, near Jiujiang, Jiangxi Province. The height of the embankment was 5.3 m and construction time was about one year. The PVDs were installed to a depth of 8.5 m at a spacing of 1.5 m in a triangular pattern. Field observations and the finite element method (FEM) were employed to analyze the performance of the soft deposit during embankment construction. The influential depth of the embankment loading was evaluated based on settlement, excess pore pressure, and stress increase in subsoil, both from the observed data and FEM analysis. The effective PVD depth was determined in the following ways: (1) the depth of 5% subsoil settlement of surface settlement; (2) vertical stress increase in subsoil of 25% in-situ stress; and (3) consolidation time/PVD depth relation by FEM. Based on the analysis, the effective depth of PVDs was determined to be between 10 and 12.8 m for this field case. 相似文献
6.
7.
The results of one-dimensional compression tests conducted on undisturbed specimens of Jiangsu soft marine clay is presented. Because of its high in situ void ratios and natural water content, Jiangsu soft marine clay displays high values of both the virgin compression index, Cc, and the secondary compression coefficient, Cα. The laboratory data indicates that the value of the ratio Cα/Cc for Jiangsu soft marine clay is constant. However, neither Cα nor Cc are constant: they both depend upon the natural water content (or void ratio) and thus are also dependent on the deformation (or compression) of Jiangsu soft marine clay. Settlement analyses show that the secondary settlement of Jiangsu soft marine clay is a significant component of the field settlement. The concept of a constant value for Cα/Cc is used to predict the secondary settlement of a surcharged embankment founded upon Jiangsu soft marine clay. The predictions are in agreement with the limited post-construction field measurements of the embankment settlement. 相似文献
8.
Guo-Wei Li Thang Ngoc Nguyen Andrew Cudzo Amenuvor 《Marine Georesources & Geotechnology》2016,34(2):154-161
This article studies the effect of dynamic cyclic loading and surcharge preloading method on the post-construction settlement of low embankments. Soil samples obtained from the soft ground under an embankment were consolidated by surcharge preloading followed by static and dynamic cyclic loading in the odometer. The results show that the consolidation deformation of the soil samples is independent of the frequency of the dynamic cyclic loading, which was simulated to follow the half-sine wave, and this is consistent with the energy concept. The post-construction settlement increases with increasing amplitude of cyclic load and the effectiveness of surcharge preloading depends on the difference between magnitude of surcharge and amplitude of the cyclic load. Based on the consolidation theory combined with the test results, a formula has been proposed to compute the post-construction settlement of a low embankment under cyclic loading. 相似文献
9.
Pitthaya Jamsawang Ekkarin Phongphinittana Panich Voottipruex Dennes T. Bergado Pornkasem Jongpradist 《Marine Georesources & Geotechnology》2013,31(7):852-869
AbstractThis research presents measurements and simulations of the full-scale behavior of a test embankment built on a soft marine clay deposit improved using soil–cement mixing (SCM) columns in Bangkok, Thailand, using both two-dimensional (2D) and 3D finite element analyses (FEAs). Fixed SCM columns with two different installation patterns, that is, column groups and column rows, were constructed in the soft clay foundation prior to the construction of the embankment. Three column wall methods, namely, equivalent width, equivalent axial rigidity, and equivalent flexural rigidity approaches, were used to convert the 3D individual columns into 2D plane strain column walls. A comparison of the results obtained through the 3D and 2D FEAs revealed that the 2D analyses provide inaccurate results in terms of the column lateral movements, bending moments, and axial loads induced in the SCM columns in addition to the factors of safety against slope failure. This outcome occurred because the actual columns in the 2D FEA were modeled using extended walls, which essentially prevent the movements of soil between two columns or column rows. Correction factors used to convert the 2D analysis results into 3D analysis results were also proposed in this study. 相似文献
10.
1 .IntroductionIt has beenrealizedthat constructing gravitystructures onsoft soil foundations is a difficult task,especiallyinthe marine area where boththe geological and environmental conditions are severe .Thisisnot only because the bearing capacity of the soft foundation is relatively low, but also because thestrength of the soft soil will befurther weakened bythe waveloading (Andersenet al .,1988 ;Ander-sen and Lauritzsen,1988 ; Yasuhara ,1988) .The strength weakening may cause serious d… 相似文献
11.
Zhaoyu Wang 《Marine Georesources & Geotechnology》2013,31(1):52-62
This paper presents a numerical model of the seismic behavior for the embankment constructed on micropile composite foundation. The effect of micropiles on soil reinforcement under static and seismic loading was studied. Embankments on the untreated and treated soil by micropiles were numerically simulated using an axisymmetric elastoplastic large deformation finite-element analysis code. The displacement caused by embankment static loading and acceleration of the embankment caused by seismic loading were calculated and compared. It was shown that micropiles can greatly reduce the settlement of the embankment and mitigate seismic response of the embankment. The main objective of this paper is to present a numerical model and to investigate the seismic behavior of micropile foundations subjected to seismic loading. A series of numerical simulations and parametric studies are presented. 相似文献
12.
Deep cement mixing (DCM) technique is a deep in-situ stabilization technique by mixing cement powder or slurry with soft soils below the ground surface to improve their properties and behavior. Some of DCM treated soft soil grounds are approximately in a plane-strain condition; for example, a fill embankment on DCM improved ground. In this study, a plane-strain physical model was created with instrumentation and used to investigate the bearing capacity and failure mode of a soft soil improved by an end-bearing DCM column group. This study focuses on the observed wedge-shaped shear failure of the model ground and attempts to give an account of the failure. Two different methods are used to calculate the bearing capacity of the model ground, and the computed values are compared with the measured ones. It is found that the simple Brom's method gives a better estimate of the bearing capacity of the present model ground. It is also found that measured data of pore water pressures at different locations in the soft soil indicate coupling between failure of columns and consolidation of the soft soil. This study has presented the first time that a wedge-shaped block failure was observed for pattern of DCM treated soil ground. 相似文献
13.
AbstractThis study investigates the impact of pile cap size, soft layer thickness and pile strength on load transfer and settlement behaviors of embankments supported by floating and fixed T-shaped deep cement mixing piles and conventional DCM piles under volume control. Preliminary investigation is performed by a series of small-scale physical model tests. The results reveal that the differential settlement can be substantially reduced with an enlarging pile cap as a result of larger embankment load transferred to the piles. The extended numerical analysis results demonstrate that the pile efficacy is related to the individual pile bearing capacity, which, in turn, depends on the pile cap size. The soft layer thickness has an insignificant effect on differential settlement but a significant effect on average settlement, while the pile strength plays an important role in differential settlement only when the cap size is not very large. Shape factor of at least 3.0 is recommended to ensure the reduction in differential settlement and minimize the effect of the change in pile strength. 相似文献
14.
Slender piles embedded in soft ground or liquefied soil may buckle under vertical load. In this paper, both small- and large-scale model tests are conducted to investigate the buckling mechanisms of a slender pile and the lateral earth pressure acting on the pile. To observe the buckling of a slender pile, the strain-controlled loading method is adopted to apply a vertical load. When the two ends of a slender pile are hinged, the buckling mechanisms of small- and large-scale model tests are same. It should be noted that this applies only to a system with a small ratio of pile bending stiffness to soil bending stiffness. An applied vertical load increases with an increasing pile head settlement until it reaches the critical buckling load. By further increasing the pile head settlement, the measured load approaches the critical buckling load. In the large-scale model test, the measured lateral earth pressure (i.e., active and passive) acting on the slender pile varies linearly with the lateral pile displacement when the measured range is 3–5?m beneath the ground. A critical buckling calculation method has been adopted to compare with the conventional “m” method. The two-sided earth pressure calculation method can achieve more approximate results with the model test. 相似文献
15.
Zhang Dingwen Liu Songyu Han Wenjun Du Guangyin 《Marine Georesources & Geotechnology》2013,31(4):332-347
A remarkable combined dry jet mixing (DJM) and prefabricated vertical drains (PVDs) method was used to enhance the performance for soft ground improvement. In the combined method, PVDs are first installed and then DJM columns are installed between the PVDs at larger spacing. This combined method improves the effectiveness of the ground improvement and creates a more economical solution. This paper presents a case study of the combined method for marine clay improvement in Lianyugang of China. The excess pore water pressure in soils created by the installation of DJM columns with and without PVDs was monitored and compared. In situ standard penetration tests were conducted in the DJM columns and before-and-after piezocone penetration tests were performed in soils surrounding the columns. Long-term settlement monitoring under embankment loading was carried out for the ground improved by combined method and DJM method alone. The field tests, settlement monitoring and economic benefit analysis results demonstrated that the DJM-PVD method is technologically sound and cost-effective as compared with the conventional DJM method. 相似文献
16.
A centrifugal model test was performed for an embankment backfilled with lime-stabilized soil on an undisturbed marine clay foundation. During the test, in-flight photographs were captured, settlements were measured by displacement sensors, and displacement contours were obtained from the markers installed on the front face of the model foundation. These test data were analyzed and discussed in this paper. The test results show that the embankment was stable at 2 m height but ruptured during the loading from 2 to 4 m height. The ratio of the maximum horizontal displacement increment to the ground settlement increment at the embankment centerline suddenly increased during the loading from 4 to 6 m height, indicating the failure of the foundation. This result is in agreement with the observation of the centrifugal test and the calculated Terzaghi ultimate bearing capacity under an undrained condition. Considering the brittle behavior and low tensile strength of the lime-stabilized soil, it is recommended that the lime-stabilized soil should only be used for a low embankment with a height less than 2 meters. 相似文献
17.
Youngcheul Kwon 《Marine Georesources & Geotechnology》2016,34(3):219-233
Difficulties in the prediction of time-distribution of consolidation settlement will be introduced by using the Murayama test embankment case of Japan. In particular, it will be discussed why the prediction of consolidation rate is difficult in multi-layered soil with complex and variable mechanical properties like organic soil or peat. It can be inferred that uncertainties, which are embedded intricately in the consolidation problem as well as given ground condition, would be major causes for consolidation settlement. After that, the author focused on the movement of pore water under the various conditions of hydraulic conductivity in the soils, and how it can affect the time-distribution of the consolidation settlement. For the applied key methodology on the consolidation settlement problem, we propose the hybrid consolidation simulation controlling the movement of pore water with high accuracy and, finally, the aim of this article is to discuss the methodological approaches obtained by the study, including the basic concept and accurate movement of pore water under various conditions of soil layers and hydraulic conductivity. 相似文献
18.
Hongyue Sun Gang Wu Xin Yan Dongfei Wang Zhenlei Wei 《Marine Georesources & Geotechnology》2018,36(8):940-949
Conventional drainage consolidation methods cause significant energy consumption and environmental issues. In this paper, a method combining siphon drainage and surcharge loading is proposed to drain water from soft soil with vertically installed prefabricated vertical drains (PVDs) and a siphon tube. To investigate the availability and effectiveness of this method, a laboratory physical modeling test was conducted to investigate the drainage and consolidation behavior. The laboratory modeling test results of this method were compared with the calculated results of the ideal sand-drained ground consolidation method to clarify the advantages and mechanism of this method. Comparison results show that the pore pressure and settlement in the proposed method developed faster than the calculation results of ideal sand-drained consolidation theory. About 10?m thickness of unsaturated zone can be formed by siphon drainage which produce a surcharge loading effect on the soil below the flow profile. Drainage is a very slow process in soft soil, and siphon drainage can work continually. Siphon drainage combined with surcharge loading is potentially a good alternative to drain water from soft clay economically and environmentally. 相似文献
19.
—Presented is the numerical analysis of settlements of soft soil by a 2-D dynamic effective stressFEM method.The model based on the results of cyclic triaxial tests on the reconstituted soft Ariake clay isused to predict the wave induced excess pore water pressure and residual strain of soft clay.The settle-ments of two types of breakwaters on the soft clay under ocean wave load,a low embankment subjected totraffic load and the tunnel surrounded by soft clay in Shanghai subjected to locomotive load are calculatedas examples. 相似文献
20.
Chunxia Huang Zhilong Sui Lei Wang Kaifu Liu 《Marine Georesources & Geotechnology》2016,34(3):244-251
The risk of liquefaction and associated ground deformation may be reduced by using various ground-improvement methods, including the stone column technique. To examine the effects of stone columns, a shaking table experimental study using four models (two containing saturated sand and two containing stone column composite foundations) was conducted to measure the development and dissipation of excess pore water pressure and the acceleration response during a simulated earthquake. The test results demonstrate that the effectiveness of stone columns for mitigation of soil liquefaction during an earthquake depends on the following three aspects: (1) the densification of the surrounding soils; (2) drainage along the stone column; and (3) reduction in the total cyclic shear stress of the soil (because the cyclic shear stress is partially shared by the stone column). The first factor (the densification of the surrounding soils) is the most prominent factor among these three. The drainage and re-distribution of the shear stress can only develop fully for sand ground with a considerably higher density; thus, the effectiveness of the last two factors are only significant for dense sand ground. 相似文献