首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献，搜索用时 796 毫秒
1.
Open‐framework gravel (OFG) in river deposits is important because of its exceptionally high permeability, resulting from the lack of sediment in the pore spaces between the gravel grains. Fluvial OFG occurs as planar strata and cross strata of varying scale, and is interbedded with sand and sandy gravel. The origin of OFG has been related to: (1) proportion of sand available relative to gravel; (2) separation of sand from gravel during a specific flow stage and sediment transport rate (either high, falling or low); (3) separation of sand from gravel in bedforms superimposed on the backs of larger bedforms; (4) flow separation in the lee of dunes or unit bars. Laboratory flume experiments were undertaken to test and develop these theories for the origin of OFG. Bed sediment size distribution (sandy gravel with a mean diameter of 1·5 mm) was kept constant, but flow depth, flow velocity and aggradation rate were varied. Bedforms produced under these flow conditions were bedload sheets, dunes and unit bars. The fundamental cause of OFG is the sorting of sand from gravel associated with flow separation at the crest of bedforms, and further segregation of grain sizes during avalanching on the steep lee side. Sand in transport near the bed is deposited in the trough of the bedform, whereas bed‐load gravel avalanches down the leeside and overruns the sand in the trough. The effectiveness of this sorting mechanism increases as the height of the bedform increases. Infiltration of sand into the gravel framework is of minor importance in these experiments, and occurs mainly in bedform troughs. The geometry and proportion of OFG in fluvial deposits are influenced by variation in height of bedforms as they migrate, superposition of small bedforms on the backs of larger bedforms, aggradation rate, and changes in sediment supply. If the height of a bedform increases as it migrates downstream, so does the amount of OFG. Changes in the character of OFG on the lee‐side of unit bars depend on grain‐size sorting in the superimposed bedforms (dunes and bedload sheets). Thick deposits of cross‐stratified OFG require high bedforms (dunes, unit bars) and large amounts of aggradation. These conditions might be expected to occur during high falling stages in the deeper parts of river channels adjacent to compound‐bar tails and downstream of confluence scours. Increase in the amount of sand supplied relative to gravel reduces the development of OFG. Such increases in sand supply may be related to falling flow stage and/or upstream erosion of sandy deposits.  相似文献   

2.
GARY KOCUREK 《Sedimentology》1981,28(6):753-780
Bounding surfaces and interdune deposits provide keys for detailed interpretations of the development, shape, type, wavelength and angle of climb of aeolian bedforms, as well as overall sand sea conditions. Current alternate interpretations of bounding surfaces require very different, but testable models for sand sea deposition. Two perpendicular traverses of Jurassic Entrada Sandstone, Utah, reveal relations among cross-strata, first-order bounding surfaces, and horizontal strata. These field relations seem explicable only as the deposits of downwind-migrating, climbing, enclosed interdune basins (horizontal strata) and dune bodies consisting of superimposed smaller crescentic dunes (cross-stratified deposits). A 1.7 km traverse parallel to the palaeowind direction provides a time-transgressive view showing continuous cosets of cross-strata, first-order bounding surfaces and interdune deposits climbing downwind at an angle of a few tenths of a degree. Changes occur in the angle of climb, cross-strata structure, and interdune deposits; these reflect changes in depositional conditions through time. A 1.5 km traverse perpendicular to the palaeowind direction provides a view at an instant in geological time showing first-order bounding surfaces and interdune deposits forming flat, laterally discontinuous lenticular bodies. The distribution of interdune sedimentary structures in this traverse is very similar to that of some modern interdune basins, such as those on Padre Island, Texas. Hierarchies of bounding surfaces in an aeolian deposit reflect the bedform development on an erg. The presence of three orders of bounding surfaces indicates dune bodies consisting of smaller, super-imposed dunes. The geometry of first-order bounding surfaces is a reflection of the shape of the inter-dune basins. Second-order bounding surfaces originate by the migration of the superimposed dunes over the larger dune body and reflect individual dune shape and type. Third-order bounding surfaces are reactivation surfaces showing stages in the advance of individual dunes. The presence of only two orders of bounding surfaces indicates simple dunes. Modern and Entrada interdune deposits show a wide variety of sediment types and structures reflecting deposition under wet, damp, and dry conditions. Interdune deposits are probably the best indicators of overall erg conditions and commonly show complex vertical sequences reflecting changes in specific depositional conditions.  相似文献   

3.
A quantitative, three‐dimensional depositional model of gravelly, braided rivers has been developed based largely on the deposits of the Sagavanirktok River in northern Alaska. These deposits were described using cores, wireline logs, trenches and ground‐penetrating radar profiles. The origin of the deposits was inferred from observations of: (1) channel and bar formation and migration and channel filling, interpreted from aerial photographs; (2) water flow during floods; and (3) the topography and texture of the river bed at low‐flow stage. This depositional model quantitatively represents the geometry of the different scales of strataset, the spatial relationships among them and their sediment texture distribution. Porosity and permeability in the model are related to sediment texture. The geometry of a particular type and scale of strataset is related to the geometry and migration of the bedform type (e.g. ripples, dunes, bedload sheets, bars) associated with deposition of the strataset. In particular, the length‐to‐thickness ratio of stratasets is similar to the wavelength‐to‐height ratio of associated bedforms. Furthermore, the wavelength and height of bedforms such as dunes and bars are related to channel depth and width. Therefore, the thickness of a particular scale of strataset (i.e. medium‐scale cross‐sets and large‐scale sets of inclined strata) will vary with river dimensions. These relationships between the dimensions of stratasets, bedforms and channels mean that this depositional model can be applied to other gravelly fluvial deposits. The depositional model can be used to interpret the origin of ancient gravelly fluvial deposits and to aid in the characterization of gravelly fluvial aquifers and hydrocarbon reservoirs.  相似文献   

4.
This study uses digital elevation models and ground‐penetrating radar to quantify the relation between the surface morphodynamics and subsurface sedimentology in the sandy braided South Saskatchewan River, Canada. A unique aspect of the methodology is that both digital elevation model and ground‐penetrating radar data were collected from the same locations in 2004, 2005, 2006 and 2007, thus enabling the surface morphodynamics to be tied explicitly to the associated evolving depositional product. The occurrence of a large flood in 2005 also allowed the influence of discharge to be assessed with respect to the process–product relationship. The data demonstrate that the morphology of the study reach evolved even during modest discharges, but more extensive erosion was caused by the large flood. In addition, the study reach was dominated by compound bars before the flood, but switched to being dominated by unit bars during and after the flood. The extent to which the subsurface deposits (the ‘product’) were modified by the surface morphodynamics (the ‘process’) was quantified using the changes in radar‐facies recorded in sequential ground‐penetrating radar surveys. These surveys reveal that during the large flood there was an increase in the proportion of facies associated with bar margin accretion and larger dunes. In subsequent years, these facies became truncated and replaced with facies associated with smaller dune sets. This analysis shows that unit bars generally become truncated more laterally than vertically and, thus, they lose the high‐angle bar margin deposits and smaller scale bar‐top deposits. In general, the only fragments that remain of the unit bars are dune sets, thus making identification of the original unit barform problematic. This novel data set has implications for what may ultimately become preserved in the rock record.  相似文献   

5.
The interpretation of fluvial styles from the rock record is based for a significant part on the identification of different types of fluvial bars, characterized by the geometric relationship between structures indicative of palaeocurrent and surfaces interpreted as indicative of bar form and bar accretion direction. These surfaces of bar accretion are the boundaries of flood‐related bar increment elements, which are typically less abundant in outcrops than what would be desirable, particularly in large river deposits in which each flood mobilizes large volumes of sediment, causing flood‐increment boundary surfaces to be widely spaced. Cross‐strata set boundaries, on the other hand, are abundant and indirectly reflect the process of unit bar accretion, inclined due to the combined effect of the unit bar surface inclination and the individual bedform climbing angle, in turn controlled by changes in flow structure caused by local bar‐scale morphology. This work presents a new method to deduce the geometry of unit bar surfaces from measured pairs of cross‐strata and cross‐strata set boundaries. The method can be used in the absence of abundant flood‐increment bounding surfaces; the study of real cases shows that, for both downstream and laterally accreting bars, the reconstructed planes are very similar to measured bar increment surfaces.  相似文献   

6.
Evolution and deposits of a gravelly braid bar, Sagavanirktok River, Alaska   总被引：2，自引：0，他引：2  
The evolution, migration and deposits of a gravelly braid bar in the Sagavanirktok River, northern Alaska, are described in unprecedented detail using annual aerial photographs, ground‐penetrating radar (GPR) profiles, trenches and cores. Compound braid bars in the Sagavanirktok River form by chute cut‐off of point bars and by growth of mid‐channel unit bars. Subsequent growth is primarily by accretion of unit bars onto their lateral and downstream margins. The upstream ends of braid bars may be sites of erosion or unit bar deposition. Compound braid bar deposits vary in thickness laterally and are thickest in medial sections and near cut banks. Compound bar deposits are typically composed of three to seven sets of simple large‐scale inclined strata, each simple set formed by a unit bar. The simple large‐scale strata contain medium‐scale cross‐strata (from dune migration) and planar strata (from migration of bedload sheets). The upstream and medial parts of compound braid bar deposits show very little vertical variation in grain size, but downstream and lateral margins tend to fine upwards. The deposits are mostly poorly sorted sands and gravels, although sands tend to be deposited at the top of the braid bar, and open‐framework gravels preferentially occur near the top and base of the braid bar. The patterns of braid bar growth and migration, and the nature of the deposits, described from the Sagavanirktok River are generally similar to other sandy and gravelly braided rivers, and consistent with the theoretical braid bar model of Bridge (1993).  相似文献   

7.
ABSTRACT In the northern parts of the Needwood and Stafford/Eccleshall Basins, England, the Pebble Beds of the Sherwood Sandstone Group contain thick successions of texturally mature, fluvial pebble/cobble conglomerates which are organized into either horizontal or cross-stratified sets. The horizontally lying sets, generally coarser grained and more poorly sorted than the cross-bedded sets, are usually disorganized and either matrix- or clast-supported, although thin lenses of well-sorted, occasionally openwork units, interpreted as falling stage phenomena, are often present. The cross-stratified conglomerates have foresets exhibiting remarkable textural organization, with a coarse, bimodal (sometimes matrix-supported) part grading upwards or being abruptly overlain by a finer, well-sorted (occasionally openwork) part and finally capped by sandstone. These rhythmic textural changes are attributed partly to an avalanche process at high stage and partly to falling stage conditions. The most common types of vertical association are thick successions of horizontally bedded conglomerates (up to 20 m) and sequences of an upwards coarsening nature (2-12 m) in which cross-stratified sets are overlain by flat-lying sets. The environment of deposition of the gravels is interpreted as one in which water depths at high stage were greater than depths in most modern braided stream plains (proglacial or alluvial fan) but shallower than depths associated with the Pleistocene catastrophic floods from which texturally mature, giant gravel bars have been recorded. Recent braided streams with relatively confined channels and considerable bar/channel relief are better analogues. In particular, medial or mid-channel bars with a two-tier structure (subaqueous and partly emergent portions) may explain the upward-coarsening sequences in which horizontally lying conglomerates overlie cross-stratified conglomerates. The thicker sequences of horizontally stratified conglomerates represent proximal, longitudinal bar deposits. Sheets of pebbly sandstone and argillaceous sandstone lying between the conglomerates, and commonly occurring towards the top of the succession, largely represent deposition from sandwaves and dunes. Finer, interbedded, argillaceous sandstones, siltstones and mudstones are interpreted as overbank and waning-flood deposits. Basin-forming tectonism of increasing intensity probably caused the initial coarsening upwards of the lower part of the succession, whilst more stable tectonic conditions and decreasing relief on the margins of the basins and in the areas of provenance in the Midlands and the Hercynides, account for the upwards-fining of the upper part of the succession.  相似文献   

8.
Aeolian dune fields characterized by partly vegetated bedforms undergoing active construction and with interdune depressions that lie at or close to the water table are widespread on Skei?arársandur, Southern Iceland. The largest aeolian dune complex on the sandur covers an area of 80 km2 and is characterized by four distinct landform types: (i) spatially isolated aeolian dunes; (ii) extensive areas of damp and wet (flooded) interdune flat with small fluvial channels; (iii) small aeolian dune fields composed of assemblages of bedforms with simple morphologies and small, predominantly damp, interdune corridors; and (iv) larger aeolian dune fields composed of assemblages of complex bedforms floored by older aeolian dune deposits that are themselves raised above the level of the surrounding wet sandur plain. The morphology of each of these landform areas reflects a range of styles of interaction between aeolian dune, interdune and fluvial processes that operate coevally on the sandur surface. The geometry, scale, orientation and facies composition of sets of strata in the cores of the aeolian dunes, and their relationship to adjoining interdune strata, have been analysed to explain the temporal behaviour of the dunes in terms of their mode of initiation, construction, pattern of migration, style of accumulation and nature of preservation. Seasonal and longer‐term flooding‐induced changes in water table level have caused episodic expansion and contraction of the wet interdune ponds. Most of the dunes are currently undergoing active construction and migration and, although sediment availability is limited because of the high water table, substantial aeolian transport must occur, especially during winter months when the surface of the wet interdune ponds is frozen and sand can be blown across the sandur without being trapped by surface moisture. Bedforms within the larger dune fields have grown to a size whereby formerly damp interdune flats have been reduced to dry enclosed depressions and dry aeolian system accumulation via bedform climb is ongoing. Despite regional uplift of the proximal sandur surface in response to glacial retreat and unloading over the past century, sediment compaction‐induced subsidence of the distal sandur is progressively placing aeolian deposits below the water table and is enabling the accumulation of wet aeolian systems and increasing the likelihood of their long‐term preservation. Wet, dry and stabilizing aeolian system types all co‐exist on Skei?arársandur and the dunes are variously undergoing coeval construction, accumulation, bypass, stabilization and destruction as a result of interactions between localized factors.  相似文献   

9.
《Sedimentology》2018,65(1):96-122
This paper characterizes the detailed sedimentology of a fluvial sandbody on Mars for the first time and interprets its depositional processes and palaeoenvironmental setting. Despite numerous orbital observations of fluvial landforms on the surface of Mars, ground‐based characterization of the sedimentology of such fluvial deposits has not previously been possible. Results from the NASA Mars Science Laboratory Curiosity rover provide an opportunity to reconstruct at fine scale the sedimentary architecture and palaeomorphology of a fluvial environment on Mars. This work describes the grain size, texture and sedimentary facies of the Shaler outcrop, reconstructs the bedding architecture, and analyses cross‐stratification to determine palaeocurrents. On the basis of bedset geometry and inclination, grain‐size distribution and bedform migration direction, this study concludes that the Shaler outcrop probably records the accretion of a fluvial barform. The majority of the outcrop consists of large‐scale trough cross‐bedding of coarse sand and granules. Palaeocurrent analyses and bedform reconstruction indicate that the beds were deposited by bedforms that migrated towards the north‐east, across the surface of a bar that migrated south‐east. Stacked cosets of dune cross‐bedding suggest aggradation of multiple bedforms, which provides evidence for short periods of sustained flow during Shaler deposition. However, local evidence for aeolian reworking and the presence of potential desiccation cracks within the outcrop suggest that fluvial deposition may have been intermittent. The uppermost strata at Shaler are distinct in terms of texture and chemistry and are inferred to record deposition from a different sediment dispersal system with a contrasting provenance. The outcrop as a whole is a testament to the availability of liquid water on the surface of Mars in its early history.  相似文献   

10.
Fluvial strata dominated internally by sedimentary structures of interpreted upper flow regime origin are moderately common in the rock record, yet their abundance is not appreciated and many examples may go unnoticed. A spectrum of sedimentary structures is recognised, all of which occur over a wide range of scale: 1. cross-bedding with humpback, sigmoidal and ultimately low-angle cross-sectional foreset geometries (interpreted as recording the transition from dune to upper plane bed bedform stability field), 2. planar/flat lamination with parting lineation, characteristic of the upper plane bed phase, 3. flat and low-angle lamination with minor convex-upward elements, characteristic of the transition from upper plane bed to antidune stability fields, 4. convex-upward bedforms, down- and up-palaeocurrent-dipping, low-angle cross-bedding and symmetrical drapes, interpreted as the product of antidunes, and 5. backsets terminating updip against an upstream-dipping erosion surface, interpreted as recording chute and pool conditions. In some fluvial successions, the entirety or substantial portions of channel sandstone bodies may be made up of such structures. These Upper Flow Regime Sheets, Lenses and Scour Fills (UFR) are defined herein as an extension of Miall's [Miall, A.D., 1985. Architectural-element analysis: a new method of facies analysis applied to fluvial deposits. Earth Sci. Rev. 22: 261–308.] Laminated Sand Sheets architectural element. Given the conditions that favour preservation of upper flow regime structures (rapid changes in flow strength), it is suggested that the presence of UFR elements in ancient fluvial successions may indicate sediment accumulation under the influence of a strongly seasonal palaeoclimate that involves a pronounced seasonal peak in precipitation and runoff.  相似文献   

11.
The ability to predict bedform migration in rivers is critical for estimating bed material load, yet there is no relation for predicting bedform migration (downstream translation) that covers the full range of conditions under which subcritical bedforms develop. Here, the relation between bedform migration rates and transport stage is explored using a field and several flume data sets. Transport stage is defined as the non‐dimensional Shields stress divided by its value at the threshold for sediment entrainment. Statistically significant positive correlations between both ripple and dune migration rates and transport stage are found. Stratification of the data by the flow depth to grain‐size ratio improved the amount of variability in migration rates that was explained by transport stage to ca 70%. As transport stage increases for a given depth to grain‐size ratio, migration rates increase. For a given transport stage, the migration rate increases as the flow depth to grain‐size ratio gets smaller. In coarser sediment, bedforms move faster than in finer sediment at the same transport stage. Normalization of dune migration rates by the settling velocity of bed sediment partially collapses the data. Given the large amount of variability that arises from combining data sets from different sources, using different equipment, the partial collapse is remarkable and warrants further testing in the laboratory and field.  相似文献   

12.
This study describes the structure of gravel bars in Nahal Zin, an ephemeral stream in the Negev desert. The internal structure of the bars was examined along trenches and in shallow pits. Gravel sheets and unit bars form during transporting flow events in the main channel, on intra-bar channels and near bar heads. Unit bars are dominated by the Go facies. Compound bars develop from accretion around, and modification of, unit bars. Compound bars are active under the current flow regime and the average depth of the fill layer is about 35 cm. The structure of compound bars is dominated by Gm (massive), containing large amounts of sand. The second most common facies is clast-supported, openwork, and well sorted sediments of the Go (pebbles) facies. Bar formation, and the development of the range of facies evident in the bars is controlled by sediment supply, particularly the high volumes of sand-sized sediment, the passage of gravel sheets and bedforms during floods, and the lateral and vertical instability of the channel. Repeated scour and fill events have produced a diverse arrangement of facies, with numerous erosional contacts between depositional units. Lateral and downstream shifts in the pattern of scour and fill due to flow and antecedent conditions shape the channel morphology and bar internal structure. Ephemeral river bars differ from those of humid and proglacial rivers in terms of the dominant facies present, the arrangement of the facies within the bars, and the sedimentary structures developed within the depositional units and on the bar surface.  相似文献   

13.
Climbing dune‐scale cross‐statification is described from Late Ordovician paraglacial successions of the Murzuq Basin (SW Libya). This depositional facies is comprised of medium‐grained to coarse‐grained sandstones that typically involve 0·3 to 1 m high, 3 to 5 m in wavelength, asymmetrical laminations. Most often stoss‐depositional structures have been generated, with preservation of the topographies of formative bedforms. Climbing‐dune cross‐stratification related to the migration of lower‐flow regime dune trains is thus identified. Related architecture and facies sequences are described from two case studies: (i) erosion‐based sandstone sheets; and (ii) a deeply incised channel. The former characterized the distal outwash plain and the fluvial/subaqueous transition of related deltaic wedges, while the latter formed in an ice‐proximal segment of the outwash plain. In erosion‐based sand sheets, climbing‐dune cross‐stratification results from unconfined mouth‐bar deposition related to expanding, sediment‐laden flows entering a water body. Within incised channels, climbing‐dune cross‐stratification formed over eddy‐related side bars reflecting deposition under recirculating flow conditions generated at channel bends. Associated facies sequences record glacier outburst floods that occurred during early stages of deglaciation and were temporally and spatially linked with subglacial drainage events involving tunnel valleys. The primary control on the formation of climbing‐dune cross‐stratification is a combination between high‐magnitude flows and sediment supply limitations, which lead to the generation of sediment‐charged stream flows characterized by a significant, relatively coarse‐grained, sand‐sized suspension‐load concentration, with a virtual absence of very coarse to gravelly bedload. The high rate of coarse‐grained sand fallout in sediment‐laden flows following flow expansion throughout mouth bars or in eddy‐related side bars resulted in high rates of transfer of sands from suspension to the bed, net deposition on bedform stoss‐sides and generation of widespread climbing‐dune cross‐stratification. The later structure has no equivalent in the glacial record, either in the ancient or in the Quaternary literature, but analogues are recognized in some flood‐dominated depositional systems of foreland basins.  相似文献   

14.
To date, published studies of alluvial bar architecture in large rivers have been restricted mostly to case studies of individual bars and single locations. Relatively little is known about how the depositional processes and sedimentary architecture of kilometre‐scale bars vary within a multi‐kilometre reach or over several hundreds of kilometres downstream. This study presents Ground Penetrating Radar and core data from 11, kilometre‐scale bars from the Río Paraná, Argentina. The investigated bars are located between 30 km upstream and 540 km downstream of the Río Paraná – Río Paraguay confluence, where a significant volume of fine‐grained suspended sediment is introduced into the network. Bar‐scale cross‐stratified sets, with lengths and widths up to 600 m and thicknesses up to 12 m, enable the distinction of large river deposits from stacked deposits of smaller rivers, but are only present in half the surface area of the bars. Up to 90% of bar‐scale sets are found on top of finer‐grained ripple‐laminated bar‐trough deposits. Bar‐scale sets make up as much as 58% of the volume of the deposits in small, incipient mid‐channel bars, but this proportion decreases significantly with increasing age and size of the bars. Contrary to what might be expected, a significant proportion of the sedimentary structures found in the Río Paraná is similar in scale to those found in much smaller rivers. In other words, large river deposits are not always characterized by big structures that allow a simple interpretation of river scale. However, the large scale of the depositional units in big rivers causes small‐scale structures, such as ripple sets, to be grouped into thicker cosets, which indicate river scale even when no obvious large‐scale sets are present. The results also show that the composition of bars differs between the studied reaches upstream and downstream of the confluence with the Río Paraguay. Relative to other controls on downstream fining, the tributary input of fine‐grained suspended material from the Río Paraguay causes a marked change in the composition of the bar deposits. Compared to the upstream reaches, the sedimentary architecture of the downstream reaches in the top ca 5 m of mid‐channel bars shows: (i) an increase in the abundance and thickness (up to metre‐scale) of laterally extensive (hundreds of metres) fine‐grained layers; (ii) an increase in the percentage of deposits comprised of ripple sets (to >40% in the upper bar deposits); and (iii) an increase in bar‐trough deposits and a corresponding decrease in bar‐scale cross‐strata (<10%). The thalweg deposits of the Río Paraná are composed of dune sets, even directly downstream from the Río Paraguay where the upper channel deposits are dominantly fine‐grained. Thus, the change in sedimentary facies due to a tributary point‐source of fine‐grained sediment is primarily expressed in the composition of the upper bar deposits.  相似文献   

15.
Fluvial ribbon sandstone bodies are ubiquitous in the Ebro Basin in North‐eastern Spain; their internal organization and the mechanics of deposition are as yet insufficiently known. A quarrying operation in an Oligocene fluvial ribbon sandstone body in the southern Ebro Basin allowed for a three‐dimensional reconstruction of the sedimentary architecture of the deposit. The sandstone is largely a medium‐grained to coarse‐grained, moderately sorted lithic arenite. In cross‐section, the sandstone body is 7 m thick, occupies a 5 m deep incision and wedges out laterally, forming a ‘wing’ that intercalates with horizontal floodplain deposits in the overbank region. Three architectural units were distinguished. The lowest and highest units (Units A and C) mostly consist of medium‐grained to coarse‐grained sandstone with medium‐scale trough cross‐bedding and large‐scale inclined stratasets. Each of Units A and C comprises a fining‐up stratal sequence reflecting deposition during one flood event. The middle unit (Unit B) consists of thinly bedded, fine‐grained sandstone/mudstone couplets and represents a time period when the channel was occupied by low‐discharge flows. The adjoining ‘wing’ consists of fine‐grained sandstone beds, with mudstone interlayers, correlative to strata in Units A and C in the main body of the ribbon sandstone. In plan view, the ribbon sandstone comprises an upstream bend and a downstream straight reach. In the upstream bend, large‐scale inclined stratasets up to 3 m in thickness represent four bank‐attached lateral channel bars, two in each of Units A and C. The lateral bars migrated downflow and did not develop into point bars. In the straight downstream reach, a tabular cross‐set in Unit A represents a mid‐channel transverse bar. In Unit C, a very coarse‐grained, unstratified interval is interpreted as deposited in a riffle zone, and gives way downstream to a large mid‐channel bar. The relatively simple architecture of these bars suggests that they developed as unit bars. Channel margin‐derived slump blocks cover the upper bar. The youngest deposit is fine‐grained sandstone and mudstone that accumulated immediately before avulsion and channel abandonment. Deposition of the studied sandstone body reflects transport‐limited sediment discharges, possibly attaining transient hyperconcentrated conditions.  相似文献   

16.
Mountney  & Howell 《Sedimentology》2000,47(4):825-849
Sets of aeolian cross‐strata within the Cretaceous Etjo Formation of NW Namibia are bounded by a hierarchy of surfaces, the origin of which are ascribed to one of four processes related to aeolian bedform and erg behaviour. The base of the main aeolian succession is characterized by a basin‐wide erosional supersurface that formed in response to a period of aeolian deflation before the onset of the main phase of erg building. Interdune migration surfaces formed by draa migration are planar in sections parallel to the palaeowind and are inclined at up to 5° in an upwind direction (SW). Perpendicular to the palaeowind, interdune surfaces form 500‐m‐wide troughs, signifying crestline sinuosity within the original bedforms. Superimposition surfaces are inclined at 5–10° in a downwind direction and indicate the migration of crescentic oblique dunes over larger, slipfaceless transverse draa. Reactivation surfaces associated with minor changes in dune slipface orientation are distinct from other bounding surface types because overlying cross‐strata lie parallel to them, rather than downlap onto them. Analysis of the geometry of these bounding surfaces, together with the orientation of the cross‐strata within the sets that they bound, has enabled the detailed morphology of the original bedforms to be reconstructed. The maximum preserved thickness of individual aeolian sets varies systematically across the basin, from 52 m in the basin depocentre to only 8 m at the basin margin. The set architecture indicates that this spatial variation is primarily the result of decreased angles of bedform climb at the basin margin, rather than the presence of smaller bedforms. Similarly, a temporal reduction in the angle‐of‐climb, rather than a reduction in bedform size, is considered to be responsible for an upward decrease in preserved set thickness. Reductions in bedform climb angle reflect progressive loss of accommodation space as the accumulating erg filled the basin.  相似文献   

17.
  相似文献   

18.
Abstract New and previously published models of wet aeolian system evolution form a spectrum of types that may be explained in terms of aeolian dune dynamics, rate of water table rise and/or periodicity of interdune flooding. This is illustrated with an example from the Mid‐Triassic (Anisian) Helsby Sandstone Formation, Cheshire, UK. Lenses of damp and wet interdune strata exhibit an intertonguing, transitional relationship with the toe‐sets of overlying aeolian dune units. This signifies dune migration that was contemporaneous with water table‐controlled accumulation in adjacent interdunes. Downwind changes in the geometry and facies of the interdune units indicate periodic expansion and contraction of the interdunes in response to changes in the elevation of the groundwater table and episodic flooding, during which accumulation of dune strata continued relatively uninterrupted. This contrasts with other models for accumulation in wet aeolian systems where interdune flooding is associated with a cessation in aeolian bedform climbing and the formation of a bypass or erosional supersurface. Architectural panels document the detailed stratigraphy in orientations both parallel and perpendicular to aeolian transport direction, enabling a quantitative three‐dimensional reconstruction of genetically related aeolian dune and interdune elements. Sets of aeolian dune strata are composed of grainflow and translatent wind‐ripple strata and are divided by a hierarchy of bounding surfaces originating from oblique migration of superimposed dunes over slipfaceless, sinuous‐crested parent bedforms, together with lee‐slope reactivation under non‐equilibrium flow conditions. Silty‐mudstone and sandstone interdune units are characterized by wind ripple‐, wavy‐ and subaqueous wave ripple‐laminae, desiccation cracks, mud flakes, raindrop imprints, load casts, flutes, intraformational rip‐up clasts and vertebrate and invertebrate footprint impressions and trackways. These units result from accumulation on a substrate that varied from dry‐ through damp‐ to wet‐surface conditions. Interdune ponds were flooded by either fluvial incursions or rises in groundwater table and were periodically subject to gradual desiccation and reflooding. Red silty‐mudstone beds of subaqueous origin pass laterally into horizontally laminated wind‐ripple beds indicating a progressive transition from wet‐ through damp‐ to dry‐surface conditions within a single interdune.  相似文献   

19.
The large-scale (i.e. bar-scale) structure of channel deposits of the braided, low-sinuosity Calamus River, Nebraska, is described using ground-penetrating radar (GPR) profiles combined with vibracores. Basal erosion surfaces are generally overlain by medium-scale, trough-cross-stratified (sets 3–25 cm thick), very coarse to medium sands, that are associated with relatively high amplitude, discontinuous GPR reflectors. Overlying deposits are bioturbated, small-scale cross-stratified (sets <3 cm thick) and vegetation-rich, fine to very-fine sands, that are associated with low-amplitude discontinuous reflectors. Near-surface peat and turf have no associated GPR reflectors. In along-stream profiles through braid and point bars, most GPR reflectors dip downstream at up to 2° relative to the basal erosion surface, but some reflectors in the upstream parts of bars are parallel to the basal erosion surface or dip upstream. In cross-stream profiles through bars, GPR reflectors are either approximately parallel to bar surfaces or have low-angle inclinations (up to 6°) towards cut banks of adjacent curved channels. Basal erosion surfaces become deeper towards cut banks of curved channels. These structures can be explained by lateral and downstream growth of bars combined with vertical accretion. Convex upwards forms up to 0·5 m high, several metres across and tens of metres long represent episodic accretion of unit bars (scroll bars and bar heads). Stratal patterns in channel fills record a complicated history of erosion and deposition during filling, including migration of relatively small bars. A revised facies model for this type of sandy, braided river has been constructed based on this new information on large-scale bedding structure.  相似文献   

20.
Bedform climbing in theory and nature   总被引：7，自引：0，他引：7  
Where bedforms migrate during deposition, they move upward (climb) with respect to the generalized sediment surface. Sediment deposited on each lee slope and not eroded during the passage of a following trough is left behind as a cross-stratified bed. Because sediment is thus transferred from bedforms to underlying strata, bedforms must decrease in cross-sectional area or in number, or both, unless sediment lost from bedforms during deposition is replaced with sediment transported from outside the depositional area. Where sediment is transported solely by downcurrent migration of two-dimensional bedforms, the mean thickness of cross-stratified beds is equal to the decrease in bedform cross-sectional area divided by the migration distance over which that size decrease occurs; where bedforms migrate more than one spacing while depositing cross-strata, bed thickness is only a fraction of bedform height. Equations that describe this depositional process explain the downcurrent decrease in size of tidal sand waves in St Andrew Bay, Florida, and the downwind decrease in size of transverse aeolian dunes on the Oregon coast. Using the same concepts, dunes that deposited the Navajo, De Chelly, and Entrada Sandstones are calculated to have had mean heights between several tens and several hundreds of metres.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号