首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献，搜索用时 36 毫秒
1.
《Applied Geochemistry》2004,19(4):611-622
Subsurface aeration is the in situ oxidation of Fe from groundwater that is used to make drinking water potable. When subsurface aeration is applied to an anaerobic groundwater system with pH>7, Fe(II) is oxidised heterogeneously. The heterogeneous oxidation of Fe(II) can result in the in situ formation of Fe colloids. To study this, the effect of substances commonly found in groundwater (e.g. PO4, Mn, silicate and fulvic acid) on the heterogeneous oxidation process was measured. The heterogeneous oxidation of Fe(II) becomes retarded when PO4, Mn, silicate or fulvic acid is present in the groundwater in addition to Fe(II). Phosphate and fulvic acid retarded the oxidation process most. The heterogeneous oxidation was described using a model with a homogeneous (k1) and an autocatalytic oxidation rate constant (k′2). From the modelling it followed that the homogeneous oxidation rate constant was not affected or even slightly elevated whereas the autocatalytic oxidation rate constant decreased remarkably by the addition of PO4, Mn, silicate or fulvic acid. From speciation calculations it followed that the decreased availability of the Fe(II) species can only explain a small part of the retarded autocatalytic oxidation process. Therefore exploratory calculations were performed to gain insight into whether the adsorption of PO4 or fulvic acid could explain the retarded autocatalytic oxidation. These calculations showed that the adsorption of fulvic acid could explain the retarded autocatalytic oxidation process. In contrast the adsorption of PO4 only partly explained the retarded autocatalytic oxidation process. In terms of colloid formation this study shows that the heterogeneous oxidation of Fe(II) in presence of PO4, Mn, silicate or fulvic acid leads to the formation of Fe colloids.  相似文献   

2.
Flow injection analysis was used to study the effect of a fulvic acid on the kinetics of iron(II) oxidation and iron colloid formation under conditions approximating fresh natural waters. While iron(II) oxidation in high-carbonate inorganic solutions is predicted well by a recently proposed homogeneous model, it overestimates the oxidation rate in low-carbonate solutions, possibly due to the formation of an intermediate iron(II) colloid or surface species. Results in fulvic acid solutions are consistent with the formation of an iron(II)-fulvic acid complex at both pH 6.0 and 8.0 which accelerates the overall oxidation rate relative to inorganic solutions. However, iron(III) complexation by fulvic acid greatly slows the formation of iron colloids, stabilizing dissolved iron(III). Decreased pH and increased ionic strength slow and decrease iron colloid formation. Evidence of a kinetic control on the distribution of iron(III) between organically complexed and colloidal forms is presented.  相似文献   

3.
The oxidation of Fe(II) with H2O2 at nanomolar levels in seawater have been studied using an UV-Vis spectrophotometric system equipped with a long liquid waveguide capillary flow cell. The effect of pH (6.5 to 8.2), H2O2 (7.2 × 10−8 M to 5.2 × 10−7 M), HCO3− (2.05 mM to 4.05 mM) and Fe(II) (5 nM to 500 nM) as a function of temperature (3 to 35 °C) on the oxidation of Fe(II) are presented. The oxidation rate is linearly related to the pH with a slope of 0.89 ± 0.01 independent of the concentration of HCO3−. A kinetic model for the reaction has been developed to consider the interactions of Fe(II) with the major ions in seawater. The model has been used to examine the effect of pH, concentrations of Fe(II), H2O2 and HCO3− as a function of temperature. FeOH+ is the most important contributing species to the overall rate of oxidation from pH 6 to pH 8. At a pH higher than 8, the Fe(OH)2 and Fe(CO3)22− species contribute over 20% to the rates. Model results show that when the concentration of O2 is two orders of magnitude higher than the concentration of H2O2, the oxidation with O2 also needs to be considered. The rate constants for the five most kinetically active species (Fe2+, FeOH+, Fe(OH)2, FeCO3, Fe(CO3)22−) in seawater as a function of temperature have been determined. The kinetic model is also valid in pure water with different concentrations of HCO3− and the conditions found in fresh waters.  相似文献   

4.
Oxidation of As(III) by natural manganese (hydr)oxides is an important geochemical reaction mediating the transformation of highly concentrated As(III) in the acidic environment such as acid mine drainage (AMD) and industrial As-contaminated wastewater, however, little is known regarding the presence of dissolved Fe(II) on the oxidation process. In this study, oxidation of As(III) in the absence and presence of Fe(II) by MnO2 under acidic conditions was investigated. Kinetic results showed that the presence of Fe(II) significantly inhibited the removal of As(III) (including oxidation and sorption) by MnO2 in As(III)-Fe(II) simultaneous oxidation system even at the molar ratio of Fe(II):As(III) = 1/64:1, and the inhibitory effects increased with the increasing ratios of Fe(II):As(III). Such an inhibition could be attributed to the formation of Fe(III) compounds covering the surface of MnO2 and thus preventing the oxidizing sites available to As(III). On the other hand, the produced Fe(III) compounds adsorbed more As(III) and the oxidized As(V) on the MnO2 surface with an increasing ratio of Fe(II):As(III) as demonstrated in kinetic and XPS results. TEM and EDX results confirmed the formation of Fe compounds around MnO2 particles or separated in solution in Fe(II) individual oxidation system, Fe(II) pre-treated and simultaneous oxidation processes, and schwertmannite was detected in Fe(II) individual and Fe pre-treated oxidation processes, while a new kind of mineral, probably amorphous FeOHAs or FeAsO4 particles were detected in Fe(II)-As(III) simultaneous oxidation process. This suggests that the mechanisms are different in Fe pre-treated and simultaneous oxidation processes. In the Fe pre-treated and MnO2-mediated oxidation pathway, As(III) diffused through a schwertmannite coating formed around MnO2 particles to be oxidized. The newly formed As(V) was adsorbed onto the schwertmannite coating until its sorption capacity was exceeded. Arsenic(V) then diffused out of the coating and was released into the bulk solution. The diffusion into the schwertmannite coating and the oxidation of As(III) and sorption of both As(V) and As(III) onto the coating contributed to the removal of total As from the solution phase. In the simultaneous oxidation pathway, the competitive oxidation of Fe(II) and As(III) on MnO2 occurred first, followed by the formation of FeOHAs or FeAsO4 around MnO2 particles, and these poorly crystalline particles of FeOHAs and FeAsO4 remained suspended in the bulk solution to adsorb As(III) and As(V). The present study reveals that the formation of Fe(III) compounds on mineral surfaces play an important role in the sorption and oxidation of As(III) by MnO2 under acidic conditions in natural environments, and the mechanisms involved in the oxidation of As(III) depend upon how Fe(II) is introduced into the As(III)-MnO2 system.  相似文献   

5.
Hydrothermal experiments were conducted to evaluate the kinetics of H2(aq) oxidation in the homogeneous H2-O2-H2O system at conditions reflecting subsurface/near-seafloor hydrothermal environments (55-250 °C and 242-497 bar). The kinetics of the water-forming reaction that controls the fundamental equilibrium between dissolved H2(aq) and O2(aq), are expected to impose significant constraints on the redox gradients that develop when mixing occurs between oxygenated seawater and high-temperature anoxic vent fluid at near-seafloor conditions. Experimental data indicate that, indeed, the kinetics of H2(aq)-O2(aq) equilibrium become slower with decreasing temperature, allowing excess H2(aq) to remain in solution. Sluggish reaction rates of H2(aq) oxidation suggest that active microbial populations in near-seafloor and subsurface environments could potentially utilize both H2(aq) and O2(aq), even at temperatures lower than 40 °C due to H2(aq) persistence in the seawater/vent fluid mixtures. For these H2-O2 disequilibrium conditions, redox gradients along the seawater/hydrothermal fluid mixing interface are not sharp and microbially-mediated H2(aq) oxidation coupled with a lack of other electron acceptors (e.g. nitrate) could provide an important energy source available at low-temperature diffuse flow vent sites.More importantly, when H2(aq)-O2(aq) disequilibrium conditions apply, formation of metastable hydrogen peroxide is observed. The yield of H2O2(aq) synthesis appears to be enhanced under conditions of elevated H2(aq)/O2(aq) molar ratios that correspond to abundant H2(aq) concentrations. Formation of metastable H2O2 is expected to affect the distribution of dissolved organic carbon (DOC) owing to the existence of an additional strong oxidizing agent. Oxidation of magnetite and/or Fe++ by hydrogen peroxide could also induce formation of metastable hydroxyl radicals (•OH) through Fenton-type reactions, further broadening the implications of hydrogen peroxide in hydrothermal environments.  相似文献   

6.
Technetium-99 (Tc) is an important fission product contaminant associated with sites of nuclear fuels reprocessing and geologic nuclear waste disposal. Tc is highly mobile in its most oxidized state and less mobile in the reduced form [Tc(IV)O2·nH2O]. Here we investigate the potential for oxidation of Tc(IV) that was heterogeneously reduced by reaction with biogenic Fe(II) in two sediments differing in mineralogy and aggregation state; unconsolidated Pliocene-age fluvial sediment from the upper Ringold (RG) Formation at the Hanford Site and a clay-rich saprolite from the Field Research Center (FRC) background site on the Oak Ridge Site. Both sediments contained Fe(III) and Mn(III/IV) as redox active phases, but FRC also contained mass-dominant Fe-phyllosilicates of different types. Shewanella putrefaciens CN32 reduced Mn(III/IV) oxides and generated Fe(II) that was reactive with Tc(VII) in heat-killed, bioreduced sediment. After bioreduction and heat-killing, biogenic Fe(II) in the FRC exceeded that in RG by a factor of two. More rapid reduction rates were observed in the RG that had lower biogenic Fe(II), and less particle aggregation. EXAFS measurements indicated that the primary reduction product was a TcO2-like phase in both sediments. The biogenic redox product Tc(IV) oxidized rapidly and completely in RG when contacted with air. Oxidation, in contrast, was slow and incomplete in the FRC, in spite of similar molecular scale speciation of Tc compared to RG. X-ray microprobe, electron microprobe, X-ray absorption spectroscopy, and micro X-ray diffraction were applied to the whole sediment and isolated Tc-containing particles. These analyses revealed that non-oxidizable Tc(IV) in the FRC existed as complexes with octahedral Fe(III) within intra-grain domains of 50-100 μm-sized, Fe-containing micas presumptively identified as celadonite. The markedly slower oxidation rates in FRC as compared to RG were attributed to mass-transfer-limited migration of O2 into intra-aggregate and intraparticle domains where Tc(IV) existed; and the formation of unique, oxidation-resistant, intragrain Tc(IV)-Fe(III) molecular species.  相似文献   

7.
Pyrite is an environmentally significant mineral being the major contributor to acid rock drainage. Synchrotron based SPEM (scanning photoelectron microscopy) and micro-XPS (X-ray photoelectron spectroscopy) have been used to characterise fresh and oxidised pyrite (FeS2) with a view to understanding the initial oxidation steps that take place during natural weathering processes. Localised regions of the pyrite surface containing Fe species of reduced coordination have been found to play a critical role. Such sites not only initiate the oxidation process but also facilitate the formation of highly reactive hydroxyl radical species, which then lead the S oxidation process.Four different S species are found to be present on fresh fractured pyrite surfaces: S22−(bulk) (4-fold coordination), S22−(surface) (3-fold coordination), S2− and S0/Sn2− (metal deficient sulfide and polysulfide respectively). These species were found to be heterogeneously distributed on the fractured pyrite surface. Both O2 and H2O gases are needed for effective oxidation of the pyrite surface. The process is initiated when O2 dissociatively and H2O molecularly adsorb onto the surface Fe sites where high dangling bond densities exist. H2O may then dissociate to produce OH radicals. The adsorption of these species leads to the formation of Fe-oxy species prior to the formation of sulfoxy species. Evidence suggests that Fe-O bonds form prior to Fe-OH bonds. S oxidation occurs through interactions of OH radicals formed at the Fe sites, with formation of SO42− occurring via S2O32−/SO32− intermediates. The pyrite oxidation process is electrochemical in nature and was found to occur in patches, where site specific adsorption of O2 and H2O has occurred. Fe and S oxidation was found to occur within the same area of oxidation probably in atomic scale proximity. Furthermore, the O in SO42− arises largely from H2O; however, depending on the surface history, SO42− formed early in the oxidation process may also contain O from O2.  相似文献   

8.
《Organic Geochemistry》1999,30(8):901-909
Deuterium nuclear magnetic resonance spectroscopy (2H-NMR) spin–lattice relaxation (T1) experiments were used to measure noncovalent interactions between deuterated monoaromatic compounds (phenol-d5, pyridine-d5, benzene-d6) and fulvic acids isolated from the Suwannee River and Big Soda Lake. Noncovalent interactions, in aqueous solution, were examined as a function of monoaromatic hydrocarbon functional groups, fulvic acid concentration and identity, and solution pH. Phenol did not exhibit noncovalent interactions with either fulvic acid at any pH. Pyridine, in a pH range from 3 to 8, interacted with Suwannee River fulvic acid, forming a bond involving the lone pair of electrons on nitrogen. Conversely, no interactions were observed between pyridine and Big Soda Lake fulvic acid; the difference in noncovalent interactions is attributed to the structural and chemical differences of the two fulvic acids. The translational and rotational molecular motion of benzene increased in the presence of both fulvic acids, indicating that in aqueous solution, fulvic acids solubilize benzene rather than forming discrete bonds as with pyridine. The results of this study demonstrate that monoaromatic functional groups, solution pH, and identity and concentration of fulvic acid can influence the type and degree of noncovalent interactions with dissolved organic matter.  相似文献   

9.
The rates of Fe(II) oxidation and precipitation from groundwater are highly pH dependent. Elevated levels of dissolved CO2 can depress pH and cause difficulty in removing dissolved Fe and associated metals during treatment of ferruginous water. This paper demonstrates interdependent changes in pH, dissolved inorganic C species, and Fe(II) oxidation rates that occur as a result of the removal (degassing) of CO2 during aeration of waters discharged from abandoned coal mines. The results of field monitoring of aeration cascades at a treatment facility as well as batchwise aeration experiments conducted using net alkaline and net acidic waters in the UK are combined with geochemical modelling to demonstrate the spatial and temporal evolution of the discharge water chemistry. The aeration cascades removed approximately 67% of the dissolved CO2 initially present but varying the design did not affect the concentration of Fe(II) leaving the treatment ponds. Continued removal of the residual CO2 by mechanical aeration increased pH by as much as 2 units and resulted in large increases in the rates of Fe(II) oxidation and precipitation. Effective exsolution of CO2 led to a reduction in the required lime dose for removal of remaining Fe(II), a very important factor with regard to increasing the sustainability of treatment practices. An important ancillary finding for passive treatment is that varying the design of the cascades had little impact on the rate of CO2 removal at the flow rates measured.  相似文献   

10.
Potentiometric titrations were used to measure conditional stability constants of UO22+-fulvic acid and UO22+-humic acid complexes. Both 2:1 and 1:1 COO-:UO22+ binding were observed. With decreasing metal concentration (2.5·10−4-6.25·10−5 M) increasing amounts of UO22+ were in the form of 1:1 humate complexes and 2:1 fulvate complexes. Despite the high nitrogen content and the low acidic OH group content, the successive stability constant values were similar to those determined for divalent cations associated with fulvic and humic compounds isolated from soils. Stability constant values increase simultaneously with increasing ionization of the humic (or fulvic) acid polyelectrolytes and with decreasing metal concentration.  相似文献   

11.
The oxidation of Cr(III) has been studied in NaCl solutions in the presence of two siderophore models, acetohydroxamic acid (Aha) and benzohydroxamic acid (Bha), the natural siderophore Desferal (DFOB) and the synthetic aminocarboxilate (ethylenedinitrilo)-tetra-acetic acid (EDTA) as a function of pH (8-9), ionic strength (0.01-2 M) and temperature (10-50 °C), at different Cr(III)-organic compound ratios. The addition of Aha and Bha caused the rates to increase at low ligand/Cr(III) ratios and decrease at high ratios. The variation of the pseudo first order rate constant (k1) as a function of the ligand concentration has been attributed to the formation of three Cr(III)-organo species (1:1, 1:2, 1:3), which can form in the presence of monohydroxamic acids. A kinetic model has been developed that gives a value of 600 (min−1) for the pseudo first order rate constant k1CrAha2+ and values approaching zero for and k1CrAha3. These kinetic results demonstrate that these monohydroxamic acids are able to bind with Cr(III) under experimental conditions that may occur in natural waters and can increase the oxidation rates of Cr(III) with H2O2 by a factor of 3.5 at an Aha/Cr(III) ratio of about 50-100.The monohydroxamic acids also affect the rates on aged products of Cr(III), suggesting that these ligands are able to affect the oxidation rates by releasing reactive Cr(III). DFOB and EDTA do not have a great effect on the oxidation of Cr(III) with H2O2. This is thought to be due to the much longer times they need to form complexes with Cr(III) compared to Aha and Bha. The rates for the formation of DFOB and EDTA complexes with Cr(III) are not competitive with the rates of the formation of aged Cr(III). After allowing Cr(III) and DFOB to react for 5 days to form the complex, reaction rates of Cr(III) with H2O2 appear to be lowered probably because of steric hindrance of the chelated Cr(III).  相似文献   

12.
A detailed experimental study was conducted to investigate mechanisms of pyrite oxidation by determining product yields and oxygen isotopic fractionation during reactions between powdered pyrite (FeS2) with aqueous hydrogen peroxide (H2O2). Sealed silica-tube experiments utilized aliquots of pyrite that were reacted with 0.2 M H2O2 for 7 to 14 days at 4 to 150 °C. No volatile sulfur species were detected in any experiment. The only gaseous product recovered was elemental oxygen inferred to result from decomposition of H2O2. Aqueous sulfate (Saq) was the only sulfur product recovered from solution. Solid hydrated ferric iron sulfates (i.e., water-soluble sulfate fraction, Sws) were recovered from all experiments. Ferric oxide (hematite) was detected only in high temperature experiments.Reactants were selected with large differences in initial δ18O values. The oxygen isotopic compositions of oxygen-bearing reactants and products were analyzed for each experiment. Subsequent isotopic mass-balances were used to identify sources of oxygen for reaction products and to implicate specific chemical reaction mechanisms. δ18O of water did not show detectable change during any experiment. δ18O of sulfate was similar for Saq and Sws and indicated that both H2O and H2O2 were sources of oxygen in sulfate. Low-temperature experiments suggest that H2O-derived oxygen was incorporated into sulfate via Fe3+ oxidation, whereas H2O2-derived oxygen was incorporated into sulfate via oxidation by hydroxyl radicals (HO). These two competing mechanisms for oxygen incorporation into sulfate express comparable influences at 25 °C. With increasing reaction temperatures from 4 to 100 °C, it appears that accelerated thermal decomposition and diminished residence time of H2O2 limit the oxygen transfer from H2O2 into sulfate and enhance the relative importance of H2O-derived oxygen for incorporation into sulfate. Notably, at temperatures between 100 and 150 °C there is a reversal in the lower temperature trend resulting in dominance of H2O2-derived oxygen over H2O-derived oxygen. At such high temperatures, complete thermal decomposition of H2O2 to water and molecular oxygen (O2) occurs within minutes in mineral-blank experiments and suggests little possibility for direct oxidation of pyrite by H2O2 above 100 °C. We hypothesize that a Fe-O2 mechanism is responsible for oxygenating pyrite to sulfate using O2 from the preceding thermal decomposition of H2O2.  相似文献   

13.
The potential for reduction of 99TcO4−(aq) to poorly soluble 99TcO2 · nH2O(s) by biogenic sediment-associated Fe(II) was investigated with three Fe(III)-oxide containing subsurface materials and the dissimilatory metal-reducing subsurface bacterium Shewanella putrefaciens CN32. Two of the subsurface materials from the U.S. Department of Energy’s Hanford and Oak Ridge sites contained significant amounts of Mn(III,IV) oxides and net bioreduction of Fe(III) to Fe(II) was not observed until essentially all of the hydroxylamine HCl-extractable Mn was reduced. In anoxic, unreduced sediment or where Mn oxide bioreduction was incomplete, exogenous biogenic TcO2 · nH2O(s) was slowly oxidized over a period of weeks. Subsurface materials that were bioreduced to varying degrees and then pasteurized to eliminate biological activity, reduced TcO4−(aq) at rates that generally increased with increasing concentrations of 0.5 N HCl-extractable Fe(II). Two of the sediments showed a common relationship between extractable Fe(II) concentration (in mM) and the first-order reduction rate (in h−1), whereas the third demonstrated a markedly different trend. A combination of chemical extractions and 57Fe Mössbauer spectroscopy were used to characterize the Fe(III) and Fe(II) phases. There was little evidence of the formation of secondary Fe(II) biominerals as a result of bioreduction, suggesting that the reactive forms of Fe(II) were predominantly surface complexes of different forms. The reduction rates of Tc(VII)O4− were slowest in the sediment that contained plentiful layer silicates (illite, vermiculite, and smectite), suggesting that Fe(II) sorption complexes on these phases were least reactive toward pertechnetate. These results suggest that the in situ microbial reduction of sediment-associated Fe(III), either naturally or via redox manipulation, may be effective at immobilizing TcO4−(aq) associated with groundwater contaminant plumes.  相似文献   

14.
The reactivity of iron(III) oxyhydroxides as reflected by their tendency to dissolve is of great importance in the redox cycling of iron and the bioavailability of iron to phytoplankton in natural waters. In this study, various iron(III) oxyhydroxides were produced by oxygenation of iron(II) in the presence of solutes, such as phosphate, sulfate, bicarbonate, valeric acid, TRIS, humic and fulvic acids, and in the presence of minerals, such as bentonite and δ-Al2O3 under conditions encountered in aquatic systems. The reactivity of the different iron(III) oxyhydroxides was subsequently assessed by means of a reductive dissolution using ascorbate and non-reductive dissolution using HQS (8-hydroxyquinoline-5-sulfonic acid) or oxalate. The experimental results show that the iron(III) oxyhydroxides with a low degree of polymerization exhibit higher reactivity than those with a high degree of polymerization or with high crystallinity. The quantity of active surface sites and the coordination arrangement of the functional groups at the surface of the iron(III) oxyhydroxides, especially the extent of the endstanding -OH groups per iron(III) ion determine the reactivity of iron(III) oxyhydroxides toward dissolution.Surfaces, such as clay and aluminum oxides, not only accelerate the oxygenation reaction of iron(II), but also induce the formation of iron(III) oxyhydroxides which are more active toward the dissolution reactions. Polymerization of iron(III) oxyhydroxides on the surfaces occurs predominantly in two dimensions rather than in three dimensions.In a laboratory experiment, the iron(III) oxyhydroxide formed in the presence of TRIS can be reduced by fulvic acid in a closed system under the following conditions: Fe(OH)3(s) 0.01 g/l, fulvic acid 5 mg/l, pH 7.5, 20°C. The kinetics of the reaction depend on the reactivity of iron(III) oxyhydroxide and reducing power of fulvic acid. Although reductants other than fulvic acid may be of importance in antural waters, this result provides the laboratory evidence that the >FeIII-OH/Fe(II) is able to act as an electron transfer mediator for the oxidation of natural organic substances, such as fulvic acid, by molecular oxygen either in the absence of microorganisms or as a supplement to microbial activity.  相似文献   

15.
Excess N from agriculture induces eutrophication in major river systems and hypoxia in coastal waters throughout the world. Much of this N is from headwaters far up the watersheds. In turn, much of the N in these headwaters is from ground-water discharge. Consequently, the concentrations and forms of N in groundwater are important factors affecting major aquatic ecosystems; despite this, few data exist for several species of N in groundwater and controls on speciation are ill-defined. Herein, we report N speciation for a spring and well that were selected to reflect agricultural impacts, and a spring and well that show little to no agricultural-N impact. Samples were characterized for NO3−, NO2−, N2O, NH4+, urea, particulate organic N(), and dissolved organic N(). These analytes were monitored in the agricultural spring for up to two years along with other analytes that we reported upon previously. For all samples, when oxidized N was present, the dominant species was NO3− (88-98% of total fixed N pool) followed by (<4-12%) and only trace fractions of the other N analytes. In the non-agriculturally impacted well sample, which had no quantifiable NO3− or dissolved O2, comprised the dominant fraction (68%) followed by NH4+ (32%), with only a trace balance comprised of other N analytes. Water drawn from the well, spring and a wetland situated in the agricultural watershed also were analyzed for dissolved N2 and found to have a fugacity in excess of that of the atmosphere. H2O2 was analyzed in the agricultural spring to evaluate the O2/H2O2 redox potential and compare it to other calculated potentials. The potential of the O2/H2O2 couple was close in value to the NO3−/NO2− couple suggesting the important role of H2O2 as an O2-reduction intermediate product and that O2 and NO3− are reduced concomitantly. The O2/H2O2 and NO3−/NO2− couples also were close in value to a cluster of other inorganic N and Fe couples indicating near partial equilibrium among these species. Urea mineralization to NO2− was found to approach equilibrium with the reduction of O2 to H2O2. By modeling as amide functional groups, as justified by recent analytical work, similar thermodynamic calculations support that mineralization to NO2− proceeds nearly to equilibrium with the reduction of O2 to H2O2 as well. This near equilibration of redox couples for urea- and -oxidation with O2-reduction places these two couples within the oxidized redox cluster that is shared among several other couples we have reported previously. In the monitored agricultural spring, [NO3−] was lower in the summer than at other times, whereas [N2O] was higher in the summer than at other times, perhaps reflecting a seasonal variation in the degree of denitrification reaction progress. No other N analytes were observed to vary seasonally in our study. In the well having no agricultural-N impact, Corg/Norg = 5.5, close to the typical value for natural aqueous systems of about 6.6. In the agricultural watershed Corg/Norg varied widely, from ∼1.2 to ?9.  相似文献   

16.
The acid-base properties of 14 standard and reference materials from the International Humic Substances Society (IHSS) were investigated by potentiometric titration. Titrations were conducted in 0.1 M NaCl under a nitrogen atmosphere, averaging 30 min from start to finish. Concentrations of carboxyl groups and phenolic groups were estimated directly from titration curves. Titration data were also fit to a modified Henderson-Hasselbalch model for two classes of proton-binding sites to obtain “best fit” parameters that describe proton-binding curves for the samples. The model was chosen for its simplicity, its ease of implementation in computer spreadsheets, and its excellent ability to describe the shapes of the titration curves. The carboxyl contents of the IHSS samples are in the general order: terrestrial fulvic acids > aquatic fulvic acids > Suwannee River natural organic matter (NOM) > aquatic humic acids > terrestrial humic acids. Overall, fulvic acids and humic acids have similar phenolic contents; however, all of the aquatically derived samples have higher phenolic contents than the terrestrially derived samples. The acid-base properties of reference Suwannee River NOM are surprisingly similar to those of standard Suwannee River humic acid. Results from titrations in this study were compared with other published results from both direct and indirect titrations. Typically, carboxyl contents for the IHSS samples were in agreement with the results from both methods of titration. Phenolic contents for the IHSS samples were comparable to those determined by direct titrations, but were significantly less than estimates of phenolic content that were based on indirect titrations with Ba(OH)2 and Ca(OAc)2. The average phenolic-to-carboxylic ratio of the IHSS samples is approximately 1:4. Models that assume a 1:2 ratio of phenolic-to-carboxylic groups may overestimate the relative contribution of phenolic groups to the acid-base chemistry of humic substances.  相似文献   

17.
Manganese oxides, typically similar to δ-MnO2, form in the aquatic environment at near neutral pH via bacterially promoted oxidation of Mn(II) species by O2, as the reaction of [Mn(H2O)6]2+ with O2 alone is not thermodynamically favorable below pH of ~?9. As manganese oxide species are reduced by the triphenylmethane compound leucoberbelein blue (LBB) to form the colored oxidized form of LBB (λmax?=?623 nm), their concentration in the aquatic environment can be determined in aqueous environmental samples (e.g., across the oxic–anoxic interface of the Chesapeake Bay, the hemipelagic St. Lawrence Estuary and the Broadkill River estuary surrounded by salt marsh wetlands), and their reaction progress can be followed in kinetic studies. The LBB reaction with oxidized Mn solids can occur via a hydrogen atom transfer (HAT) reaction, which is a one-electron transfer process, but is unfavorable with oxidized Fe solids. HAT thermodynamics are also favorable for nitrite with LBB and MnO2 with ammonia (NH3). Reactions are unfavorable for NH4+ and sulfide with oxidized Fe and Mn solids, and NH3 with oxidized Fe solids. In laboratory studies and aquatic environments, the reduction of manganese oxides leads to the formation of Mn(III)-ligand complexes [Mn(III)L] at significant concentrations even when two-electron reductants react with MnO2. Key reductants are hydrogen sulfide, Fe(II) and organic ligands, including the siderophore desferioxamine-B. We present laboratory data on the reaction of colloidal MnO2 solutions (λmax?~?370 nm) with these reductants. In marine waters, colloidal forms of Mn oxides (<?0.2 µm) have not been detected as Mn oxides are quantitatively trapped on 0.2-µm filters. Thus, the reactivity of Mn oxides with reductants depends on surface reactions and possible surface defects. In the case of MnO2, Mn(IV) is an inert cation in octahedral coordination; thus, an inner-sphere process is likely for electrons to go into the empty e g * conduction band of its orbitals. Using frontier molecular orbital theory and band theory, we discuss aspects of these surface reactions and possible surface defects that may promote MnO2 reduction using laboratory and field data for the reaction of MnO2 with hydrogen sulfide and other reductants.  相似文献   

18.
《Applied Geochemistry》2004,19(7):995-1009
Published literature on preservation procedures for stabilizing aqueous inorganic As(III/V) redox species contains discrepancies. This study critically evaluates published reports on As redox preservation and explains discrepancies in the literature. Synthetic laboratory preservation experiments and time stability experiments were conducted for natural water samples from several field sites. Any field collection procedure that filters out microorganisms, adds a reagent that prevents dissolved Fe and Mn oxidation and precipitation, and isolates the sample from solar radiation will preserve the As(III/V) ratio. Reagents that prevent Fe and Mn oxidation and precipitation include HCl, H2SO4, and EDTA, although extremely high concentrations of EDTA are necessary for some water samples high in Fe. Photo-catalyzed Fe(III) reduction causes As(III) oxidation; however, storing the sample in the dark prevents photochemical reactions. Furthermore, the presence of Fe(II) or SO4 inhibits the oxidation of As(III) by Fe(III) because of complexation reactions and competing reactions with free radicals. Consequently, fast abiotic As(III) oxidation reactions observed in the laboratory are not observed in natural water samples for one or more of the following reasons: (1) the As redox species have already stabilized, (2) most natural waters contain very low dissolved Fe(III) concentrations, (3) the As(III) oxidation caused by Fe(III) photoreduction is inhibited by Fe(II) or SO4.  相似文献   

19.
The naturally abundant nitrogen in soil and aquatic NOM samples from the International Humic Substances Society has been characterized by solid state CP/MAS 15N NMR. Soil samples include humic and fulvic acids from the Elliot soil, Minnesota Waskish peat and Florida Pahokee peat, as well as the Summit Hill soil humic acid and the Leonardite humic acid. Aquatic samples include Suwannee River humic, fulvic and reverse osmosis isolates, Nordic humic and fulvic acids and Pony Lake fulvic acid. Additionally, Nordic and Suwannee River XAD-4 acids and Suwannee River hydrophobic neutral fractions were analyzed. Similar to literature reports, amide/aminoquinone nitrogens comprised the major peaks in the solid state spectra of the soil humic and fulvic acids, along with heterocyclic and amino sugar/terminal amino acid nitrogens. Spectra of aquatic samples, including the XAD-4 acids, contain resolved heterocyclic nitrogen peaks in addition to the amide nitrogens. The spectrum of the nitrogen enriched, microbially derived Pony Lake, Antarctica fulvic acid, appeared to contain resonances in the region of pyrazine, imine and/or pyridine nitrogens, which have not been observed previously in soil or aquatic humic substances by 15N NMR. Liquid state 15N NMR experiments were also recorded on the Elliot soil humic acid and Pony Lake fulvic acid, both to examine the feasibility of the techniques, and to determine whether improvements in resolution over the solid state could be realized. For both samples, polarization transfer (DEPT) and indirect detection (1H–15N gHSQC) spectra revealed greater resolution among nitrogens directly bonded to protons. The amide/aminoquinone nitrogens could also be observed by direct detection experiments.  相似文献   

20.
The rates of Sb(III) oxidation by O2 and H2O2 were determined in homogeneous aqueous solutions. Above pH 10, the oxidation reaction of Sb(III) with O2 was first order with respect to the Sb(III) concentration and inversely proportional to the H+ concentrations at a constant O2 content of 0.22 × 10−3 M. Pseudo-first-order rate coefficients, kobs, ranged from 3.5 × 10−8 s−1 to 2.5 × 10−6 s−1 at pH values between 10.9 and 12.9. The relationship between kobs and pH was:
  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号