首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献，搜索用时 31 毫秒
1.
This work presents the first calibration results for the SARAL/AltiKa altimetric mission using the Gavdos permanent calibration facilities. The results cover one year of altimetric observations from April 2013 to March 2014 and include 11 calibration values for the altimeter bias. The reference ascending orbit No. 571 of SARAL/AltiKa has been used for this altimeter assessment. This satellite pass is coming from south and nears Gavdos, where it finally passes through its west coastal tip, only 6 km off the main calibration location. The selected calibration regions in the south sea of Gavdos range from about 8 km to 20 km south off the point of closest approach. Several reference surfaces have been chosen for this altimeter evaluation based on gravimetric, but detailed regional geoid, as well as combination of it with other altimetric models.

Based on these observations and the gravimetric geoid model, the altimeter bias for the SARAL/AltiKa is determined as mean value of ?46mm ±10mm, and a median of ?42 mm ±10 mm, using GDR-T data at 40 Hz rate. A preliminary cross-over analysis of the sea surface heights at a location south of Gavdos showed that SARAL/AltiKa measure less than Jason-2 by 4.6 cm. These bias values are consistent with those provided by Corsica, Harvest, and Karavatti Cal/Val sites. The wet troposphere and the ionosphere delay values of satellite altimetric measurements are also compared against in-situ observations (?5 mm difference in wet troposphere and almost the same for the ionosphere) determined by a local array of permanent GNSS receivers, and meteorological sensors.  相似文献   

2.
On 25 February 2013, the Satellite for Argos and AltiKa (SARAL) was launched from the Indian Sriharikota launch site. The AltiKa payload consisted of an altimeter and a radiometer. This paper describes the AltiKa radiometer. This instrument has been studied for several years by CNES, TAS-F, ASTRIUM-F and a set of science laboratories, and AltiKa is the first compact instrument embedding simultaneously the altimeter and radiometer functions. AltiKa radiometer is a dual frequency instrument working in K (23.8 GHz) and Ka band (37 GHz), it is based on the total power principle, with direct detection receivers. On-ground acceptance tests exhibited a very high level of performance: less than 0.2 dB has been estimated for both sensitivity and absolute accuracy in both frequencies. This paper focuses on the in-flight performances that have been observed since the launch. All the instrument observable characterizations are nominal, and in-flight sensitivity has been estimated lower than 0.2 K.  相似文献   

3.
The CNES/ISRO mission SARAL/AltiKa was successfully launched on 25 February 2013. It reached its nominal orbit on 13 March 2013. AltiKa is the first altimeter using the Ka-band frequency. This article presents the results of the calibration and validation activities perfromed on the first year of the SARAL/AltiKa mission. The main objective of the article is to assess the SARAL/AltiKa data quality and to estimate the altimeter system performance using GDR products. To achieve this goal, we present mono-mission metrics and compare them with Jason-2 over the same period. Even if these missions do not have the same ground track, precise comparisons are still possible. They allow assessing parameter discrepancies and SSH consistency between both missions in order to detect geographically correlated biases, jumps or drifts. These results show that SARAL/AltiKa data quality is excellent: ocean data coverage is greater than 99.5%, standard deviation at cross-overs is 5.4 cm. The mission therefore fulfills the requirements of high precision altimetry and can be used (in conjunction with Jason-2) to monitor the global mean sea level, ensuring the continuity of the record over ERS/Envisat historical ground track. Possible improvements and open issues are also identified, foreseeing an even better mission performance.  相似文献   

4.
The geodetic Corsica site was set up in 1998 in order to perform altimeter calibration of the TOPEX/Poseidon (T/P) mission and subsequently, Jason-1 and OSTM/Jason-2. The scope of the site was widened in 2005 in order to undertake the calibration of the Envisat mission and most recently of SARAL/AltiKa. Here we present the first results from the latter mission using both indirect and direct calibration/validation approaches. The indirect approach utilizes a coastal tide gauge and, as a consequence, the altimeter derived sea surface height (SSH) needs to be corrected for the geoid slope. The direct approach utilizes a novel GPS-based system deployed offshore under the satellite ground track that permits a direct comparison with the altimeter derived SSH. The advantages and disadvantages of both systems (GPS-based and tide gauges) and methods (direct or indirect) will be described and discussed. Our results for O/IGD-R data show a very good consistency for these three kinds of products: their derived absolute SSH biases are consistent within 17 mm and their associated standard deviation ranges from 31 to 35 mm. The AltiKa absolute SSH bias derived from GPS-zodiac measurement using the direct method is ?54 ±10 mm based on the first 13 cycles.  相似文献   

5.
We present an initial assessment of SARAL/AltiKa data in the coastal band. The study focuses on the Ibiza Channel where the north-south water exchanges play a key role in controlling the circulation variability in the western Mediterranean. In this area, the track 16 of SARAL/AltiKa intercepts the domain covered by a coastal high-frequency (HF) radar system, which provides surface currents with a range up to 60 km. We evaluate the performance of the SARAL/AltiKa Ssalto/Duacs delayed-time along-track products compared to the HF radar surface velocity fields. SARAL/AltiKa data are retrieved at a distance of only 7 km from the coast, putting in evidence the emerging capabilities of the new altimeter. The derived velocities resolved the general features of the seasonal mesoscale variability with reasonable agreement with HF radar fields (significant correlations of 0.54). However, some discrepancies appear, which might be caused by instrumental hardware radar errors, ageostrophic velocities as well as inaccurate corrections and editing in the altimeter data. Root mean square (rms) differences between the estimated SARAL/AltiKa and the HF radar velocities are about 13 cm/s. These results are consistent with recent studies in other parts of the ocean applying similar approaches to Topex/Poseidon and Jason-1 missions and using coastal altimeter corrections.  相似文献   

6.
The SARAL/AltiKa project is based on a single Ka band altimeter (35.75 GHz), which is the first oceanography altimeter to operate at such a high frequency. Ka band offers reduced radar footprint in comparison to traditional Ku band altimeters and negligible ionospheric effects. In this paper we present and evaluate benefits of AltiKa altimeter applied in the study of lakes in Andean chain in South America. Water levels time series obtained with Envisat/RA-2 and SARAL/AltiKa altimeters over 17 lakes of various sizes are calculated and compared to in situ observations. SARAL/AltiKa measurements tend to be extremely well correlated with in situ measurements and offer significant improvements compared to the Envisat mission.  相似文献   

7.
In the absence of many gauging stations in the major and mighty river systems, there is a need for satellite-based observations to estimate temporal variations in the river water storage and associated water management. In this study, SARAL/AltiKa application for setting up hydraulic model (HEC-RAS) and river flow simulations over Tapi River India has been discussed. Waveform data of 40 Hz from Ka band altimeter has been used for water levels retrieval in the Tapi river. SARAL/AltiKa retrieved water levels were converted to discharge in the upstream location (track-926) using the rating curve available for the nearby gauging site and using linear spatial interpolation technique. Steady state simulations were done for various flow conditions in the upstream. Validation of river flow model was done in the downstream location (track-367) by comparing simulated and altimeter retrieved water levels (RMSE 0.67 m). Validated model was used to develop rating curve between water levels and simulated discharge for the downstream location which enables to monitor discharge variations from satellite platform in the absence of in situ observations. It has been demonstrated that SARAL/AltiKa data has potential for river flow monitoring and modeling which will feed for flood disaster forecasting, management and planning.  相似文献   

8.
The AltiKa altimeter onboard SARAL is a joint CNES/ISRO mission launched in February 2013 that has the same 35 days repeat orbit of the previous European altimeters, Envisat, and ERS-1/2. SARAL/AltiKa is thus a unique opportunity to extend the repeat observations of this orbit that have been surveyed since 1991. However, the altimeter operates in Ka-band, which is higher than the previous frequencies, and offers new paths of investigation. The penetration depth is theoretically reduced from around 10 m in Ku-band to less than 1 m in Ka-band, such that the volume echo originates from the near subsurface. Second, the sharper antenna aperture leads to a narrower leading edge that reduces the impact of the ratio between surface and volume echoes of the height retrieval. Indeed, the spatial and temporal observations of AltiKa at cross-over points and along-track indicate that the impact of backscatter changes on the height decreasesfrom 0.3 m/dB for the Ku-band to only 0.05 m/dB for the Ka-band. Therefore, the height measurement is stable over time. Moreover, the volume echo in the Ka-band results from the near subsurface layer and is mostly controlled by ice grain size, unlike the Ku-band.  相似文献   

9.
The accuracy of the marine gravity field derived from satellite altimetry depends on dense track spacing as well as high range precision. Here, we investigate the range precision that can be achieved using a new shorter wavelength Ka-band altimeter AltiKa aboard the SARAL spacecraft. We agree with a previous study that found that the range precision given in the SARAL/AltiKa Geophysical Data Records is more precise than that of Ku-band altimeter by a factor of two. Moreover, we show that two-pass retracking can further improve the range precision by a factor of 1.7 with respect to the 40 Hz-retracked data (item of range_40 hz) provided in the Geophysical Data Records. The important conclusion is that a dedicated Ka-band altimeter-mapping mission could substantially improve the global accuracy of the marine gravity field with complete coverage and a track spacing of <6 km achievable in ～1.3 years. This would reveal thousands of uncharted seamounts on the ocean floor as well as important tectonic features such as microplates and abyssal hill fabric.  相似文献   

10.
The resolution of seamount geoid anomalies by the SARAL/AltiKa Ka-band radar altimeter is compared with the Envisat RA2 Ku-band altimeter using cross-spectral analysis of exact-repeat profiles. Noise spectra show white noise floors at root-mean-square levels around 8 mm per root-Hz for AltiKa and 19 mm per root-Hz for RA2, and are colored at wavelengths longer than a few km, with a spectral hump similar to that seen in Jason-2 data. The AltiKa noise level is lower than the RA2 noise level by more than one would expect from the ratio of their pulse repetition frequencies. Large outliers are present in data from both altimeters, always of one sign (range too long), and show little correlation with rain or other error flags. Seamount anomaly signal to noise ratios are 30 to 10 dB for AltiKa and 3 to 8 dB less for RA2, decreasing as seamount size decreases. Seamounts as small as 1.35 km tall are resolved by both instruments, with significantly better performance by AltiKa due to its lower noise level. If AltiKa can fly a geodetic mission, it will find many presently unknown seamounts.  相似文献   

11.
This paper presents an assessment of SARAL/AltiKa satellite altimeter for the monitoring of a tropical western boundary current in the south-western Pacific Ocean: the East Caledonian Current. We compare surface geostrophic current estimates obtained from two versions of AltiKa along-track sea level height (AVISO 1 Hz and PEACHI 40 Hz) with two kinds of dedicated in situ datasets harvested along the satellite ground tracks: one deep-ocean current-meter mooring deployed in the core of the boundary current and five glider transects. It is concluded that the AltiKa-derived current successfully captures the velocity of the boundary current, with a standard error of 11 cm/s with respect to the in situ data. It also appears important to reference AltiKa sea level anomaly to the latest mean dynamic topography available in our area. Doing so, Ka-band altimetry provides a satisfactory representation of the western boundary current. Thereby, it usefully contributes to observing its variability in such a remote and under-observed ocean region. However, the rather long repeat period of SARAL (35 days) in comparison to the high frequency variability seen in the flow velocity of the boundary current calls for a combined use of SARAL with the other satellite altimetry missions.  相似文献   

12.
This study presents the results of the 2013 Ibiza (Western Mediterranean) calibration campaign of Jason-2 and SARAL altimeters. It took place from 14 to 16 September 2013 and comprised two phases: the calibration of the GNSS (Global Navigation Satellite System) buoys to estimate the antenna height of each of them and the absolute calibration to estimate the altimeter bias (i.e., the difference of sea level measured by radar altimetry and GNSS). The first one was achieved in the Ibiza harbor at a close vicinity of the Ibiza tide gauge and the second one was performed at ～ 40 km at the northwest of Ibiza Island at a crossover point of Jason-2 and SARAL nominal groundtracks. Five buoys were used to delineate the crossover region and their measurements interpolated at the exact location of each overflight. The overflights occurred two consecutive days: 15 and 16 September 2013 for Jason-2 and SARAL, respectively. The GNSS data were processed using precise point positioning technique. The biases found are of (?0.1 ± 0.9) and (?3.1 ± 1.5) cm for Jason-2 and SARAL, respectively.  相似文献   

13.
As a part of our calibration/validation activities five months of SARAL/AltiKa wave data have been analyzed in this study. A robust quality control procedure using threshold values on signal and retrieved wave heights was implemented before the assimilation. Assimilation runs in the wave model Météo-France (MFWAM) were performed for a long period. The validation of the model outputs was performed with independent wave observations from altimeter and buoy data. The results indicate good performance in terms of bias and scatter index for the significant wave height and the peak wave period. Statistical analyses were performed for different ocean basins (high and intermediate latitudes and tropics). The use of SARAL/AltiKa and Jason-2 wave data combined was also investigated. This leads to further improvements for the analysis and forecast periods. In other respects, the impact of the assimilation of SARAL/AltiKa wave data is discussed for waves under strong wind conditions such as typhoons Fitow and Danas which occurred in early October 2013.  相似文献   

14.
SARAL/AltiKa GDR-T are analyzed to assess the quality of the significant wave height (SWH) measurements. SARAL along-track SWH plots reveal cases of erroneous data, more or less isolated, not detected by the quality flags. The anomalies are often correlated with strong attenuation of the Ka-band backscatter coefficient, sensitive to clouds and rain. A quality test based on the 1 Hz standard deviation is proposed to detect such anomalies. From buoy comparison, it is shown that SARAL SWH is more accurate than Jason-2, particularly at low SWH, and globally does not require any correction. Results are better with open ocean than with coastal buoys. The scatter and the number of outliers are much larger for coastal buoys. SARAL is then compared with Jason-2 and Cryosat-2. The altimeter data are extracted from the global altimeter SWH Ifremer data base, including specific corrections to calibrate the various altimeters. The comparison confirms the high quality of SARAL SWH. The 1 Hz standard deviation is much less than for Jason-2 and Cryosat-2, particularly at low SWH. Furthermore, results show that the corrections applied to Jason-2 and to Cryosat-2, in the data base, are efficient, improving the global agreement between the three altimeters.  相似文献   

15.
SARAL uses the same orbit as ERS and Envisat and can be used to extend inland water height time series derived from these missions. This article investigates the potential of SARAL for this application over the Great Lakes and the Amazon basin. SARAL/AltiKa is the first altimeter using Ka-band that is rarely influenced by ionospheric effects but susceptible for atmospheric water. Our investigations show clear waveform disruptions for SARAL due to precipitation. It is demonstrated that the quality of water heights improved when using alternative retracker products, for example, the ice-1 product. The improvement depends on the weather and yields up to 3.8 cm for wet conditions. The advantage of the smaller footprint of SARAL is demonstrated for land-water transitions where SARAL provides better water level heights up to 6 km to the lakeshore whereas Envisat is limited to about 11 km. SARAL provides also more reliable water level heights for narrow Amazon rivers than Envisat. Furthermore, the hooking effect is decreased for SARAL. Comparing water level time series of SARAL-only, Envisat-only, and multi-mission with in-situ data demonstrates that SARAL has the potential to extend Envisat long-term time series and to decrease the RMS by about 10% for large lakes and 40% for selected rivers.  相似文献   

16.
The focus of this study is the validation of significant wave height (SWH) and sea surface height anomaly (SSHA) obtained from the first Ka-band altimeter AltiKa onboard SARAL (Satellite for ARGOS and Altimeters). It is a collaborative mission of the Indian Space Research Organization and Centre National d'Etudes Spatiales (CNES). This is done using in-situ observations from buoy and Jason-2 measurements. Validation using buoy observations are at particular locations while that using Jason-2 altimeter is an attempt towards global validation of Altika products. The results clearly indicate that the SARAL/AltiKa provide high-quality data and the errors are within a predefined range of accuracy. A parallel validation of SWH from other altimeters, which monitored ocean since last decade, like EnviSAT and Jason-2 was also performed with buoy observations. The results clearly show that the accuracy of AltiKa SWH is much better than EnviSAT and comparable to reference mission Jason-2. The accuracy is quite good for the calm sea while in the rough seas the accuracy degrades some. The inter-comparison of SARAL/AltiKa SSHA with Jason-2 indicates a fair match between them. These validation exercises demonstrate the high quality of AltiKa products, usable for practical applications.  相似文献   

17.
SARAL/AltiKa completed its first year in orbit in March 2014. The 1 Hz GDR-T data of the first 10 cycles of the mission are used to perform a comprehensive quality assessment by means of a global multi-mission crossover analysis. Within this approach, SARAL sea surface heights are compared with data from other current missions, mainly Jason-2 and Cryosat-2, to reveal its accuracy and consistency with the other altimeter systems. Alongside with global mean range bias and instrumental drifts, investigations on geographically correlated errors as well as on the realization of the systems origin are performed. The study proves the high quality and reliability of SARAL. The mission shows only a small range bias of about ?5 cm with respect to Jason-2 and neither significant time-tag bias nor instrumental drifts. With 1.3 cm the scatter of radial errors is in the same order of magnitude as for Cryosat-2 and Jason-1 GM and will probably further improve using an enhanced sea state bias (SSB) model. However, the wet tropospheric corrections from SARAL radiometer still show some systematic effects influencing the range bias as well as geographically correlated error patterns and the z-component of the origin. Improved inflight calibration will be necessary to overcome these effects.  相似文献   

18.
In the present study, behavior of the SARAL/AltiKa (Satellite with ARgos and ALtiKa) waveforms over Maithon Reservoir (～65 km2 of surface area), Jharkhand, India, has been studied. The estimated water level has been compared with the in situ measurements at hydro-gauging station at the dam site. The problem of minimization of errors in the water level retrieval from AltiKa measurements has been resolved by improvement of the retracking method. A real retracking gate detection algorithm based on statistical analysis harnessing various physical parameters of the waveform has been developed, which has been applied to SARAL/AltiKa waveforms over the Maithon reservoir. Comparing the in-situ measurements with altimetry data (from cycle 1, 19 March 2013 to cycle 12, 8 April 2014) showed that it is crucial to improve the retracking method. Results showed accuracy of water level monitoring increased by nearly 76% by the newly developed waveform retracking algorithm over non-retracked water level. We also compared this new method with the existing ice-1 algorithm and found that with the new method there is improvement of ～27% over ice-1 retracked water level. The correlation coefficient values and root mean square values without retracking, with ice-1 algorithm and with newly developed retracking algorithm were 0.87, 0.91, and 0.95, and 8.12 cm, 2.08 cm, and 1.42 cm, respectively. This shows the proposed retracker performed better than ice-1. The retracking procedure helped in outliers' identification and substitution and with waveform fitting and waveform parameter extraction. This algorithm should have good performance capability for retrieving water level over inland water bodies like Maithon reservoir.  相似文献   

19.
SARAL/AltiKa has a Dual Frequency Microwave Radiometer (DFMR), and Jason-2 has an Advanced Microwave Radiometer (AMR). Both microwave radiometer sensors include a 23.8 GHz primary water sensing channel. The measurement consistencies between DFMR and AMR are important for establishing a consistent altimetry data set between SARAL/AltiKa and Jason-2 in order to accurately assess sea level rise in a long-term time series. This study investigates the measurement consistency in the 23.8 GHz channel between DFMR and AMR at the Simultaneous Nadir Overpasses (SNO's) between the two satellites and also at coldest ocean brightness temperature locations. Preliminary results show that while both instruments show no significant trends over the one year since the launch of SARAL, a consistent relative bias of 2.88 K (DFMR higher than AMR) with a standard deviation of 0.98 K is observed. The relative bias at the lowest brightness temperature from the SNO method (-3.82 K) is consistent with that calculated from coldest ocean method (-3.74 K). The relative bias exhibits strong latitude (and scene temperature) dependency, changing from -3.82 K at high latitudes to -0.92 K near the equator. There also exists an asymmetry between the northern and southern hemisphere. The relative bias increases toward the lower end of brightness temperature.  相似文献   

20.
With the launch of SARAL/AltiKa altimeter, efforts have been made to develop wind speed retrieval algorithms. Here we present two algorithms for estimating and validating wind speed from AltiKa. The first method is based on a theoretical Geophysical Model Function (GMF) using forward model simulations for Ka band specifications. The second is the model function developed using the matched database of input and output vectors of Normalized Radar Cross Section (NRCS) from AltiKa and wind speed measurements from concurrent Jason-2 altimeters. Since the NRCS depends on both the surface roughness due to surface wind speed and on mean square slope of the surfaces, the significant wave height is used along with wind speed for model development as an proxy variable. Both the theoretical and empirical GMFs are evaluated for retrieval of wind speed from AltiKa and validated with NDBC buoys data. The empirical model provide wind speed retrieval accuracy of 1.4 m/s. The accuracy of wind retrievals from theoretical model is also in the similar range (1.6 m/s), indicating the sound physical basis applicable for the future altimeters with various incidence angles. The retrieved wind speed is applied for various case studies, bringing out all the regional and global features quite well.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号