共查询到20条相似文献，搜索用时 31 毫秒
1.
干湿循环对非饱和膨胀土抗剪强度影响的试验研究 总被引：1，自引：0，他引：1
膨胀土是一种气候敏感性土体,研究在干湿循环过程中膨胀土剪切强度的变化,对了解在自然界周期性蒸发和降雨作用下原位膨胀土体工程性质的变化以及由此导致的地质灾害发生过程具有重要意义。文中以重塑非饱和膨胀土为研究对象,模拟了3次干湿循环过程,对每次干燥路径中的试样进行了直剪试验,重点分析含水率、正压力及干湿循环次数对膨胀土剪切强度的影响,得到如下主要结果：（1）在干燥过程中,随着含水率的减小,试样的刚度、脆性、抗剪强度值（峰值剪切应力）、抗剪强度指标（黏聚力、内摩擦角）及抗剪强度损失（峰值强度与残余强度之差）均呈增加趋势;（2）正压力越高,试样的剪切强度和残余强度越大,而破坏后的峰值强度损失越小,破坏韧性增加;（3）在3次干燥过程中,试样的剪切强度及黏聚力呈先增加后减小的趋势,在第二次干燥过程中达到峰值,但内摩擦角受干湿循环的影响无明显规律;（4）试样经历多次干湿循环后,其剪切特性越来越类似于超固结土,脆性显著增加;（5）干燥过程和干湿循环对试样残余剪切强度的影响都不明显,残余剪切强度基本都在100 kPa附近变化;（6）非饱和膨胀土在干湿循环及干燥过程中剪切强度的变化除了与吸力有关外,还与其微观结构调整和裂隙发育状态密切相关,需要综合非饱和土力学和土质学理论对试验现象进行分析。 相似文献
2.
The impact of cyclic wetting and drying on the swelling behaviour of stabilized expansive soils 总被引：5，自引：0，他引：5
Black cotton soil (BCS) deposits, stabilized with waste materials-wood-ash and organic matter (leaves, grass, etc.) exist in BCS areas of North Karnataka, India. These ash-modified soils (AMS) are apparently stabilized by hydrated lime produced by biochemical, dissolution, and hydration reactions. The influence of cyclic wetting and drying on the swelling behaviour of wood-ash-modified BCS and laboratory lime-treated BCS specimens are examined in this study. Such a study is required to assess the long-term behaviour of chemically stabilized soils in geotechnical applications. Cyclic wetting and drying caused the AMS specimens to become more porous and less saturated. Consequently, the cyclically wetted and dried (or desiccated) AMS specimens collapsed significantly at the experimental flooding pressures. The beneficial effects of lime-stabilization of the BCS specimens were also partially lost in cyclically wetting and drying them. The clay contents of the lime-treated BCS specimens increased on cyclic wetting and drying. The increased clay contents in turn, affected their Atterberg limits and swell–shrink potentials. Partial loss of inter-particle cementation, increased porosity, and reduced degree of saturation, also imparted small to moderate collapse potentials to the desiccated lime-treated BCS specimens. 相似文献
3.
R. M. Hen-Jones P. N. Hughes R. A. Stirling S. Glendinning J. E. Chambers D. A. Gunn Y. J. Cui 《Acta Geotechnica》2017,12(5):1159-1173
Current assessments of slope stability rely on point sensors, the results of which are often difficult to interpret, have relatively high costs and do not provide large-area coverage. A new system is under development, based on integrated geophysical–geotechnical sensors to monitor groundwater conditions via electrical resistivity tomography. So that this system can provide end users with reliable information, it is essential that the relationships between resistivity, shear strength, suction and water content are fully resolved, particularly where soils undergo significant cycles of drying and wetting, with associated soil fabric changes. This paper presents a study to establish these relationships for a remoulded clay taken from a test site in Northumberland, UK. A rigorous testing programme has been undertaken, integrating the results of multi-scalar laboratory and field experiments, comparing two-point and four-point resistivity testing methods. Shear strength and water content were investigated using standard methods, whilst a soil water retention curve was derived using a WP4 dewpoint potentiometer. To simulate seasonal effects, drying and wetting cycles were imposed on prepared soil specimens. Results indicated an inverse power relationship between resistivity and water content with limited hysteresis between drying and wetting cycles. Soil resistivity at lower water contents was, however, observed to increase with ongoing seasonal cycling. Linear hysteretic relationships were established between undrained shear strength and water content, principally affected by two mechanisms: soil fabric deterioration and soil suction loss between drying and wetting events. These trends were supported by images obtained from scanning electron microscopy. 相似文献
4.
多次干湿循环后土-水特征曲线的模拟 总被引：3，自引：0，他引：3
目前对于土体的干湿循环过程中变形、强度变化规律研究较多,而对经过多次干湿循环后土-水特征曲线的试验研究较少。由于吸力平衡需要时间太长,对干湿循环过程中土-水特征曲线的研究也多限于单次的干湿循环试验。但考虑到实际岩土工程中气候条件的多变性和自然环境的复杂性,一般土体均要经历多次干湿循环,因此,对多次干湿循环后的土-水特性曲线研究显得非常重要。结合已有的试验数据总结脱湿曲线与吸湿曲线随着干湿循环次数的变化规律,通过引入一个与干湿循环次数有关的函数,提出能预测多次干湿循环后土-水特征曲线的方法。本方法仅需土-水特征曲线的首次干湿循环脱湿与吸湿曲线和塑性指数,就可以预测多次干湿循环后的土-水特征曲线。 相似文献
5.
Yahia E.-A. Mohamedzein Amer A. Al-Rawas 《Geotechnical and Geological Engineering》2011,29(6):999-1008
Sabkha soils are salt-bearing formations that are formed in arid regions. In their in situ states the sabkha soils have high
compressibility and low shear strength. These soils are also heterogeneous and their properties depend on the type and amount
of salt present. Thus, these soils are not suitable for support of infrastructures without the risk of high settlement and/or
bearing capacity failure. This paper investigates the possibility of using cement to improve the shear strength of sabkha
soils for possible use as a foundation-bearing soil. The sabkha soil used in this study is a sandy sabkha obtained from the
coastal plains at Al-Auzayba, Sultanate of Oman. Cement was added in percentages of 2.5, 5, 7.5 and 10%, by dry weight of
soil. The soil-stabilizer mixers were allowed to cure for 7, 14 and 28 days. Laboratory tests such as compaction, unconfined
compression, consolidated undrained triaxial and durability tests were performed to measure the engineering characteristics
of the stabilized material. The results showed substantial improvements in the shear strength of the sabkha–cement mixtures
and the mixtures are also durable with small weight loss after 12 wetting/drying cycles. Thus, cement can be used to improve
the shear strength of sabkha soils. Furthermore, the effective stress path and the tress-strain relation of the sabkha–cement
mixtures follow trends similar to those of cemented calcareous soils. 相似文献
6.
固化铅污染土的干湿循环耐久性试验研究 总被引：2，自引：0，他引：2
在商用高岭土、膨润土与商业黄砂混合物中加入硝酸铅溶液,添加水泥和石灰两种固化剂,采用室内压实制样方法获得固化的铅污染土试样。进行干、湿循环试验,测试固化体的质量损失和无侧限抗压强度等参数随干、湿循环次数的变化规律,评价固化铅污染土的干、湿耐久性。测试结果表明,本试验8种配比的试样都满足干、湿循环的要求;黏土矿物为膨润土的试样干、湿循环耐久性比黏土矿物为高岭土的试样要差;水泥固化土的干、湿循环耐久性要略优于石灰固化土;加入 8 000 mg/kg的铅可略增大土体的抗干、湿循环耐久性。水泥和石灰固化/稳定化重金属污染土时,土体中含水率是保证加固效果的关键参数之一。土体中含水率应能满足固化剂充分水化、水解、火山灰和碳酸化反应之需要。 相似文献
7.
In nature, soils are often composed of varying amounts of clay, silt and sand. Variation of the percentage of these compositions can affect the final strength of the soils when stabilised with cement. In this study, focus was placed on clayey soils with different gradation of sand impurities up to 40% in mass. An extensive study of such clayey soils treated with cement was investigated. For the results, it is noted that water:cement ratio was a major influence of strength development of cement-treated clayey soils. In contrast, the soil:cement ratio was found to have minor effects on the strength development. The presence of sand impurities has a significant reduction on the strength development of the cement-treated clayey soil mixture due to more free water available for hydration. The use of free-water:cement ratio is adopted which was shown to be capable of adjusting for such change in amount of free water and water holding capacity of the clay which is determined with Atterberg’s liquid limit tests. The effects of gradation (fine, coarse and well-graded) of the sand impurities were found to affect strength development minimally, owing to similarities in their liquid limits when mixed with clay. Ordinary Portland cement (OPC)-treated clayey soils produced a more rapid gain in strength but lower final strength at 28 days of curing as compared with Portland blast furnace cement (PBFC). This is found to be persistent for different gradation of sand impurities. A linear correlation can be established based on the log of the unconfined compressive strengths developed at different curing age, with slopes of these linear trends found to be similar for PBFC and OPC-treated clayey soil specimens. Finally, a strength prediction model comprising of these findings is developed. The parameters adopted in this model coincide with values proposed by past studies, thereby validating the robustness of the model. The practical benefits from this study offer a quality control scheme to forecast long-term performance of cement-treated clayey soils as well as optimise cement dosage in cement stabilisation to produce a more cost-effective and less environmental-invasive usage of the technology in geotechnical applications.
相似文献8.
为研究超细水泥含量对水泥固化软土的早期力学性能的影响,本文通过在普通水泥中加入不同掺量的超细水泥组成复合水泥固化剂用以固化软土。具体研究不同超细水泥掺量、不同初始含水率、及不同养护围压条件下,复合水泥固化剂对固化软土早期抗压强度及刚度的影响。采用自制K0围压养护装置(施加不同轴向压力的方式)、无侧限抗压强度仪(UCS)、X射线衍射仪(XRD)、电镜扫描仪(SEM)和低场核磁共振孔隙测试仪(NMR)等试验手段获取复合水泥固化软土不同龄期的抗压强度、刚度及微观结构的变化规律,并揭示其固化机理。研究结果表明:(1)相同轴向压力作用下,随着超细水泥掺量的增加,固化软土的抗压强度和弹性模量均有提高,其中复合固化剂中的活性颗粒发生水化反应生成大量胶凝产物用以黏聚土颗粒和填充孔隙,惰性颗粒用于填充土颗粒间的孔隙;(2)随着含水率的提高,固化软土中孔相对发育,从而使固化软土结构致密性减弱,抗压强度降低;(3)在K0围压养护7d时,固化软土的抗压强度和弹性模量随着轴向压力的提高而增加,表明养护围压对软土颗粒的压缩作用能提高固化软土的密实性,同时围压对固化软土产生有效应力,与水化产物共同促进固化软土形成密实的土骨架,进而使其在7d内具有较高的抗压强度。基于试验结果,建立轴向压力、含水率和超细水泥掺量等多因素的固化软土强度预测公式,并提出复合水泥固化软土结构模型,为工程实践提供理论基础。 相似文献
9.
The climatic zones where residual soils occur are often characterized by alternate wet and dry seasons. Laboratory studies
of earlier workers have established that the alternate wetting and drying process affects the swell-shrink potentials, water
content, void ratio and particle cementation of expansive soils. The influence of cyclic wetting and drying on the collapse
behaviour of residual soils has not been examined. This paper examines the influence of alternate wetting and drying on the
collapse behaviour of compacted residual soil specimens from Bangalore District. Results of such a study are useful in anticipating
changes in collapse behaviour of compacted residual soil fills. Experimental results indicated that the cyclic wetting and
drying process increased the degree of expansiveness of the residual soils and reduced their collapse tendency. Changes in
the swell/collapse behaviour of compacted residual soil specimens from wetting drying effects are attributed to reduction
in water content, void ratio and possible growth of cementation bonds. 相似文献
10.
Clay soil with low-bearing capacities can present great problems underlying pavement and light structures due to uncertainty associated with their performance. This paper describes a sonic based testing methodology for quality control of a surface stabilized soil. From an engineering aspect, an increase in water content has a number of disadvantageous consequences: cohesion decreases, the soil swells, the alternating dry-out/shrinkage and wetting/swelling effects destroy the rock or a soil structure. Cement is mixed into the soil to increase both the strength and the usability of local soils in constructions purposes. This is to overcome the problems by strengthening the soil underlying the structure or diminishing the leads transmitted from the foundation to the soil. The compressive strength of the stabilized soil is highly dependent on the type of soil, moisture content, cement content, and compaction work, and can therefore vary significantly in the field. The authors performed the quality control by measuring the sonic and tensile strength velocity in the stabilized soil that has been correlated to compressive strength in native materials. The improvement of the soil materials by the addition of cement could make the material suitable as filling materials, foundation and/or a road base construction. The quality control for the stabilized soils was investigated using sonic measurements and strength gain. The test methods were performed to evaluate the degree of improvement achieved through the measurement of compression and shear-wave velocities of the soil under study. Scanning electron microscopy and electron dispersive X-ray analyses were performed on raw and laboratory treated for qualitative understanding the strength minerals formed during stabilization. The sonic test showed a considerable improvement with curing time and percentages of stabilizer. Mineralogical studies indicated the formation of silica and alumina hydrates along with interwoven structure of cement treated clay particles suggesting adequate mixing of the soil and binder owing to the strength of the soil materials. 相似文献
11.
Effect of Cement and Quarry Dust on Shear Strength and Hydraulic Characteristics of Lithomargic Clay
The lithomargic clay constitutes an important group of residual soils existing under lateritic soils. This soil is found on
the western and eastern coasts of India over large areas. This soil is a problematic one and is very sensitive to water and
loses a greater part of its strength when becomes saturated. These high silt deposits have invited many problems such as slope
failures, foundation failures, embankment failures, uneven settlements etc. In this investigation an attempt is made to study
the effect of cement and quarry dust on shear strength and hydraulic characteristics of the lithomargic clay after the stabilization.
Microfabric and mineralogical studies were carried out to find out the reason for the strength development of the stabilized
soil using SEM and XRD analysis. The results indicated that there is an improvement in the properties of the lithomargic clay
with the addition of cement and quarry dust. The XRD results indicated the formation of CSH and CAH, which are responsible
for strength development in the stabilized soil. 相似文献
12.
非饱和残积土的土-水特征曲线试验及模拟 总被引：4，自引：0，他引：4
土-水特征曲线是指基质吸力与含水率或饱和度的关系曲线。土-水特征及其相关数学模型可用于非饱和土性质如渗透系数和抗剪强度模型的建立。通常,土-水特征曲线仅有脱湿曲线。笔者详细讨论了初始含水率、干密度、竖向应力及干湿循环对脱湿曲线的影响。采用滤纸法测试了厦门地区残积土的土-水特征曲线(SWCC)及滞回环。结果表明,初始含水率对SWCC影响较小,最优含水率干侧试样SWCC的进气值小,滞回环小;湿侧试样的进气值大,滞回环大;最优含水率试样的滞回环居中。初始干密度对SWCC有显著影响,低干密度试样SWCC进气值小,脱湿速率快;高干密度试样SWCC进气值高,脱湿速率低。滞回环的大小随着初始干密度的减小而增大。不同竖向应力下SWCC变化较大。随着竖向应力的增加,进气值增大,脱湿速率减小,滞回环减小并趋于稳定。第1次干湿循环对SWCC影响最大,随着循环次数的增加,进气值减小,滞回环减小并趋于稳定。由于残积砂质黏性土SWCC的过渡区和残余区不易区分,残余含水率难以确定,因此,提出5种剔除残余含水率参数的修正SWCC模型,计算分析得出,修正Gardner模型最适合厦门地区残积土的SWCC建模。 相似文献
13.
以非饱和粉土为研究对象,利用吸力可控的动三轴仪对其进行动力变形试验,得到了在不同净围压和不同吸力路径下非饱和粉土试样的骨架曲线、动弹性模量和阻尼比,研究了先脱湿后吸湿的吸力历史对其动力变形特性的影响。结果表明,在同一净围压和吸力下,非饱和粉土试样经历过先脱湿后吸湿的骨架曲线和动弹性模量比仅经过脱湿的要高,而试样经历过先脱湿后吸湿的阻尼比比仅经过脱湿的要小;此外,随着非饱和粉土试样经历过最大吸力的增大,其骨架曲线和动弹性模量增大,而阻尼比减小。试验结果可用非饱和土的平均骨架应力和弯液面水的表面张力作用来解释,并用两项联合预测非饱和土试样的最大剪切模量。 相似文献
14.
水泥土固化过程中Ca2+浓度会随水化反应的进行而逐步降低,导致水泥颗粒未完全水化,固化土强度增长受限,而水泥基渗透结晶型防水材料（CCCW）中活性物质能催化未水化水泥颗粒反应。选择硫铝酸盐水泥（SAC）为胶凝材料、CCCW为添加剂,通过单掺与复掺的方式,结合X射线衍射（XRD）、电镜扫描（SEM）表征,分析了固化土的无侧限抗压强度、水稳定性、耐干湿循环性能及微观结构。结果表明,复掺16%混合料（4%CCCW+12%SAC）的固化土强度是同掺量下单掺SAC固化土强度的1.5倍,且比单掺20%SAC的固化土强度高1.41 MPa;复掺16%混合料（4%CCCW+12%SAC）的固化土泡水2～8 d软化系数平均达0.97,而同掺量下SAC固化土平均仅为0.73;单掺的固化土强度随干湿循环次数增加逐级降低,而复掺混合料的固化土强度呈波浪式发展;CCCW中活性物质能增加固化土中钙矾石生成量并修复微裂缝,钙矾石长径比显著增大,可直接连接两个甚至多个土颗粒,形成三维网状结构,显著提高结晶体的微观加筋、骨架及填充作用,改善SAC固化土强度、水稳定性及耐干湿循环性能。 相似文献
15.
高钙粉煤灰是燃煤电厂排出的固体废物,其堆放不仅需占用大量土地,而且对周围环境存在严重威胁。通过系统的室内试验,着重研究了高钙粉煤灰固化铅与锌污染土的工程性质,揭示了其作用机制,探讨了利用高钙粉煤灰固化重金属污染土的可行性。试验结果表明,土体受到重金属离子污染后其无侧限抗压强度降低,掺入高钙粉煤灰可提高土体强度,并能抑制重金属离子的滤出;污染物浓度较低时,固化污染土中的Pb2+和Zn2+均能得到有效固化,污染物浓度较高时,Zn2+的固化效果优于Pb2+。干湿循环试验结果表明,高钙粉煤灰固化污染土的强度随干湿循环次数的增加,先增大后减小;固化土体中重金属离子浓度较低时,滤出液中金属离子浓度随干湿循环次数增加而增大;重金属离子浓度较高时,滤出液中金属离子浓度基本保持不变。 相似文献
16.
为研究水泥砂浆固化土剪切强度特性和合理确定水泥砂浆固化土工程应用的配比,从掺砂量、水泥掺入比、原料土含水率及砂料粒径入手,对水泥砂浆固化土进行了室内固结不排水三轴（CU）试验研究。结果表明,掺砂可以改善固化土强度;随掺砂量的增加,黏聚力和有效黏聚力先增加后减小,转折点的掺砂量为最佳掺砂量（10%左右）,内摩擦角和有效内摩擦角不断增加,一定掺砂量下增加水泥掺入比可有效地提高固化土的强度;随着含水率的增加,固化土的黏聚力呈近似线性减小的关系,而内摩擦角几乎保持不变,采用水泥砂浆处理高含水率软弱地基时适当提高掺砂量,可以较大幅度改善固化土的力学性质;在掺料配比一定的情况下砂料粒径对固化土的抗剪强度指标存在一定的影响。采用单一粒径砂料的固化土抗剪强度更高,该单一粒径在固化土级配良好的前提下,不均匀系数Cu趋于最大、曲率系数Cc趋于最小 相似文献
17.
石灰改良红层无侧限抗压强度试验研究 总被引：3，自引：1，他引：2
红层是一种特殊岩土,作为路基材料时,常会导致不均匀沉陷、翻浆冒泥等病害。为改善其力学性质,工程上通常掺入一定剂量的石灰（Ca（OH）2）进行改良。由于降水-蒸发的周期性变化,运营期间反复干湿循环作用对路基土的工程性质造成较大影响。基于此,结合室内无侧限抗压强度试验,研究了干湿循环作用对不同掺量的石灰改良红层无侧限抗压强度的影响。结果表明：在最佳含水率下,石灰改良红层的无侧限抗压强度随石灰掺量的增加而增大;干湿循环作用对改良红层无侧限抗压强度的影响与石灰掺量有关,石灰掺量较低时,改良红层的抗压强度随干湿循环次数的增加而减小,石灰掺量较高时,改良红层的无侧限抗压强度随干湿循环次数的增加而显著增大;未改良红层塑性较大,试样均为塑性鼓胀破坏,掺入石灰后,红层强度增大,脆性增强,呈脆性剪切破坏,经历干湿循环作用后,石灰改良红层试样呈多缝锥形破坏。 相似文献
18.
矿渣胶凝材料固化软土的力学性状及机制 总被引：4，自引：0，他引：4
利用矿渣胶凝材料固化软土,既可利用工业废渣,又能减少水泥的用量。以矿渣胶凝材料固化黏土、砂土二种软土。发现矿渣胶凝材料加固软土的效果远好于水泥、石灰,其9 %掺量的固化土28 d的无侧限强度达到2.0 MPa以上,普遍高于15 %掺量的水泥固化土,且其28 d固化土的软化系数普遍高于90 %以上,固化黏土后CBR值远高于同掺量的石灰固化土。X衍射结构分析表明,矿渣胶凝材料水化时产生的高强难溶的矿物晶体是其固化软土效果好的主要原因。因此,矿渣胶凝材料是一种性能优异的软土加固材料。 相似文献
19.
This paper investigates the drying and wetting soil water retention curves (SWRCs) of statically compacted lime-stabilised London Clay specimens. A series of tests were performed using the contact filter paper method, pressure plate apparatus and a suction-controlled triaxial system incorporating the axis translation technique. These investigated the water retention of the soil under different boundary and stress-state conditions and simultaneously determined the volume change in the soil during drying and wetting. Factors relevant to the lime treatment of soils, such as curing period and method (air vs. water curing), were also considered. Finally, the hysteresis of the SWRC of the chemically treated soil (for which there appears to be a lack of information in the international literature) was investigated. The results showed that the treatment with lime increased the volumetric stability but reduced the water retention ability due to a more open structure enabled by the flocculation and chemical bonding effects. Curing period and method effect appears to be small. Hysteresis was noted to some degree in all instances. 相似文献
20.
硅酸盐水泥作为常规的土壤固化剂存在高能耗、高排放等问题,研究人员一直在寻求一种更加经济环保的水泥代替品。使用基于高炉矿渣（ground granulated
blast-furnace slag,简称 GGBS）、粉煤灰（ fly ash,简称 FA）的地聚合物对砂土进行加固,通过调整激发剂的种类和配比、矿渣与粉煤灰比例、水灰比和养护条件等,研究不同因素对地聚合物固化砂土力学性能的影响。通过无侧限抗压强度（unconfined compressive
strength,简称 UCS）测试、电子计算机断层扫描（ computed tomography,简称 CT ）分析、扫描电子显微镜（scanning electron
microscope,简称 SEM）对试样进行了深入研究。结果表明：基于 GGBS-FA 的地聚合物可有效地提高砂土的力学性能;复合激发剂的加固效果优于单组分激发剂;低温不会明显降低地聚合物固化砂土的最终力学性能,仅延缓了地质聚合反应和结构的形成;碱性环境对地聚合物固化砂土的强度有促进作用;酸性环境及长时间暴露在空气中,会降低地聚合物固化砂土的强度。 相似文献