共查询到20条相似文献，搜索用时 593 毫秒
1.
用三维梁-颗粒模型BPM3D(beam-particlemodelinthreedimensions)对岩石类非均质脆性材料的力学性质和破坏过程进行了数值模拟。梁-颗粒模型是在离散单元法基础上,结合有限单元法中的网格模型提出的用于模拟岩石类材料损伤破坏过程的数值模型。在模型中,材料在细观层次上被离散为颗粒单元集合体,相邻颗粒单元由有限单元法中的弹脆性梁单元联结。梁单元的力学性质均按韦伯(Weibull)分布随机赋值,以模拟岩石类材料力学参数的空间变异性。材料内部裂纹通过断开梁单元来模拟。通过自动生成的非均质材料模型对岩石类材料的破坏机理进行研究。岩石类非均质脆性材料在单轴压缩状态下破坏过程细观数值模拟结果显示,岩石材料宏观破坏是由于其内部细观裂纹产生、扩展、贯通的结果。通过数值模拟结果之间的对比分析,揭示出岩石试样宏观破坏模式随细观层次上韦伯分布参数的变化而不同。与实际矿柱破坏形态的对比分析表明了模型的适用性。根据数值模拟结果对岩石类非均质材料的破坏机理进行了探讨。 相似文献
2.
大量的细观试验研究发现,岩石破坏主要是裂纹沿着岩石晶体颗粒边界的扩展造成的（沿晶断裂）,裂纹沿弯折晶界的扩展则构成了不同材料边界上翼裂纹的扩展。基于以上细观试验结果,建立奇异单元的有限元模型,通过对节点位移的数值外插法,得到了岩石材料沿晶断裂翼裂纹应力强度因子,并研究了晶粒几何特征和材料非均质性（Dundurs参数）对裂纹扩展的影响。研究表明：在均质情况下,晶粒的几何形状在接近正六边形的情况下最适合裂纹扩展。随着非均质性的增强,各主翼裂纹比和晶粒几何角度所对应的KI值都要较均质模型的结果更高,最大的KI 所对应的晶粒的内角角度也有所增加。综合所有计算结果可以看出,岩石中晶粒的非均质程度越高,越利于岩石破裂。 相似文献
3.
将数字图像技术与Munjiza提出的有限元法-离散元法（FDEM）耦合分析方法结合,研制了可表征岩石真实非均质性的FDEM分析系统,为从细观角度对岩体进行建模以及研究岩体的破裂机制提供了新途径。该系统借助数字图像技术从岩石断面的图像获取岩石材料的真实细观结构,借助成熟的网格剖分技术,将其映射到FDEM计算网格中,从而克服了原有FDEM在考虑材料非均质性所存在的不足。利用该系统,进行了巴西圆盘劈裂试验的数值模拟,再现了花岗岩在荷载作用下的真实破裂过程。数值模拟结果表明,考虑非均质性的岩样应力分布呈现出非对称性,岩石的细观结构对岩石中裂纹的扩展及应力分布有重要影响。 相似文献
4.
脆性岩石破裂演化过程的三维细胞自动机模拟 总被引：4，自引：1，他引：3
在三维条件下定义了实体细胞自动机的基本组件,综合运用弹塑性理论、细胞自动机自组织演化理论、统计原理以及岩石力学理论等,建立了模拟岩石三维破裂过程的张量型细胞自动机模型,并开发了相应的数值模拟软件EPCA3D。利用EPCA3D对脆性岩石进行单轴压缩破裂过程模拟,通过破裂模式、岩样内部破裂情况、全应力-应变曲线和声发射曲线等的分析,揭示岩石破裂的机制。结果表明,EPCA3D能够较好地模拟非均质岩石在载荷作用下微裂纹的萌生、扩展和贯通的全过程。利用该模拟系统,采用应力-应变线性组合的加载控制方式,研究了不同围压对岩石全应力-应变曲线的影响。研究结果表明：对于脆性非均质岩石,低围压下容易表现为II类行为,且强度较低;高围压下容易表现为I类变形行为,且强度较高。 相似文献
5.
6.
储层非均质性对水力压裂的影响 总被引：1，自引：0，他引：1
从岩石细观非均质性的特点出发,采用RFPA2D-Flow软件对单孔和双孔数值模型进行压裂计算,研究岩石非均质性对水力压裂的响应,重点探讨双孔模型孔间吸引效应对裂纹演化形态的影响。岩石细观单元的力学、水力学特性由统计分布生成以体现岩石的随机不均质性,水力压裂过程中流体压力传递通过单元渗流-损伤耦合迭代来实现。数值计算结果表明:(1)岩石非均质性影响裂缝的扩展形态,导致水力裂纹尖端微裂纹的分支。随着均质度的增加,水力裂纹的扩展形态变得更加平直光滑,单孔模型两侧裂纹更加对称,双孔间裂纹的连通性变差。(2)岩石的非均匀性对于岩石的起裂压力和地层破裂压力影响较大。随着均质度的增大,起裂应力和地层破裂应力增大,并且两者间的差值逐渐变小,在储层为均质的条件下,两者几乎相等。(3)相同的边界条件下,均质模型的应力分布曲线光滑连续,非均质模型的应力分布曲线呈现出明显波动,井眼对称剖面上的应力分布不尽相同,反映了细观单元强度非均匀性及裂缝扩展形态对应力分布的影响。(4)双孔模型孔间存在孔隙水压力增加带,孔间产生吸引效应,双孔方位影响临界压力。研究结果对水压裂试验设计和现场压裂施工具有一定的参考意义。 相似文献
7.
化学溶液及其水压作用下单裂纹灰岩破裂的细观试验 总被引：3，自引：0，他引：3
采用岩石破裂全过程的细观力学试验系统进行了化学溶液及其水压力作用下单裂纹灰岩压缩破裂试验。通过电镜扫描、X衍射、水质分析等分析方法,对岩石微观形貌、矿物成分等进行研究。采用数字显微系统,对其压缩破裂过程进行实时观测和记录,得到了岩石破裂过程的细观图像;探讨了蒸馏水、不同pH值的0.1 mol/L Na2SO4溶液及其水压力作用对单裂纹灰岩变形和强度特性的影响。研究表明,受化学侵蚀后岩石的结构及成分均发生了不同程度的变化,导致其非均质性增加,而强度、弹性模量等降低,其力学性质劣化的程度与岩石中矿物成分的变化程度相关;孔隙水压的作用改变了岩石内部裂隙面和颗粒间的受力状态,加速了岩石裂纹的扩展,降低了岩石强度,水化学溶液及其水压作用使得岩石的破裂形式变得更为复杂。 相似文献
8.
在振动载荷作用下,岩石内部细观缺陷的发展将导致其宏观力学性能的劣化。为了提高超声波振动碎岩效率,采用数值模拟与实验研究相结合的方法,对超声波振动下岩石内部的损伤过程进行分析;采用有限元与统计技术相结合的方法,建立岩石二维模型,引入损伤增量因子的概念,分析岩石非均匀性对岩石裂纹扩展过程的影响。研究结果表明:1)岩石材料在超声波振动下的损伤过程分为萌生、扩展、贯通3个阶段,随着非均匀系数的增加,岩石原始裂纹的扩展效率逐渐加快。2)损伤因子存在一个临界值,约为0.005 4:当某一时刻岩石的损伤因子低于0.005 4时,损伤增量因子与非均匀系数的响应关系不明显;当损伤因子高于0.005 4时,损伤增量因子随着非均匀系数的增大而急剧增大,此时岩石非均匀性对损伤因子的影响不容忽视。 相似文献
9.
冲击载荷作用下准脆性材料Ⅱ型裂纹扩展研究 总被引：1，自引：0，他引：1
冲击载荷作用下准脆性材料的动态断裂一直是关注的热点问题,Ⅱ型裂纹试样受冲击剪切时其裂纹扩展方向同材料力学性质和冲击速度等密切相关。应用岩石动态破裂过程动态分析系统软件,对单边平行双裂缝试样开展了冲击载荷作用下的裂纹动态扩展数值模拟,分别研究了不同材料力学性质、材料均质度、入射应力脉冲幅值和历时对II型裂纹动态扩展的影响。数值模拟结果表明,纯II型裂纹在动荷载作用下的扩展,不仅受到剪切损伤,而且还存在拉伸损伤;准脆性材料的非均匀性导致了主裂缝周围产生大量微裂纹的破坏,影响裂缝的分岔和内部的应力值;应力幅值和应力脉冲历时分别超过某一定值时,主裂缝将出现分叉现象,试样的破坏程度加剧,其研究结果对于深入揭示准脆性材料在动荷载作用下II型裂纹扩展的规律及准脆性材料的损伤断裂机制具有重要的参考价值。 相似文献
10.
对预制交叉裂隙岩石试样进行裂纹扩展试验,研究了裂纹萌生、扩展、聚合过程,分析了主裂隙和轴向载荷夹角及主次裂隙夹角对裂纹起裂应力和聚合应力的影响,并用混合有限元-离散元程序,即图形处理器并行化的3D Y-HFDEM代码对试验进行了仿真计算,实现了岩石破坏从连续介质向非连续介质的过渡,对裂纹类及损伤破坏模式进行了识别,捕捉到了试验中难以发现的现象。研究表明：随主裂隙与轴向载荷夹角增加,裂纹聚合区的拉伸裂纹数量增加;裂纹起裂和聚合应力与主裂隙与轴向载荷夹角成正比;主次裂隙夹角增加,岩石的破坏模式由拉伸破坏转为剪切破坏,交叉裂隙加剧岩石破碎程度;主裂隙尖端萌生扩展的拉伸-剪切混合裂缝引起的破坏在岩石破坏中占主导地位,是导致岩体失去承载能力的主控裂纹;混合有限元-离散元仿真软件GPGPU并行化的3D Y-HFDEM IDE在岩石裂纹扩展研究中具有优势,可以捕捉实验室难以发现的损伤断裂类型,可以作为岩石裂纹扩展研究的有力工具。 相似文献
11.
风化花岗岩物理力学性质的弱化给工程稳定性带来很大影响,因此,研究不同风化程度花岗岩的破坏特性具有重要意义。利用河南五岳抽水蓄能电站库区采集的风化花岗岩,结合现场岩芯特征的定性描述及波速比定量评价指标,划分出了微、弱、强3种不同风化程度的花岗岩;对单轴压缩破坏后产生的碎屑进行质量和尺度的特征分析,在此基础上建立了碎屑分形维数值与波速比之间的对应关系,并利用MATLAB对花岗岩破坏后主破裂表面裂缝进行分形维数计算。结果表明：风化试样产生的碎屑以粗粒组为主,且随风化程度增强,粗粒组碎屑质量占比逐渐增大;强风化岩石碎屑长厚比分布范围小,块状碎屑占比低,破坏动力学特性不明显,其形状更单一,主要以板状为主;随着风化程度的降低,块状碎屑含量增多,岩石动力学破坏特征增强,碎屑分形维数随着表征风化程度波速比的增大而呈增大趋势;相较于碎屑质量、宽度和厚度,碎屑数量和长度是影响碎屑分形维数的主控因素,是反映不同风化程度花岗岩破碎分形特征的主要参量;强风化类组花岗岩表面裂缝分形随波速比变化不明显,而弱风化、微风化花岗岩的裂缝分形维数随波速比增大而呈显著增大趋势,说明其自相似程度更高,形状更复杂,而在裂缝形成过... 相似文献
12.
Muhammad Saleem Mughal Muhammad Sabir Khan Muhammad Rustam Khan Sohail Mustafa Fahad Hameed Muhammad Basharat Abrar Niaz 《Arabian Journal of Geosciences》2016,9(8):528
Late Proterozoic rocks of Tanol Formation in the Lesser Himalayas of Neelum Valley area are largely green schist to amphibolite facies rocks intruded by early Cambrian Jura granite gneiss and Jura granite representing Pan-African orogeny event in the area. These rocks are further intruded by pegmatites of acidic composition, aplites, and dolerite dykes. Based on field observations, texture, and petrographic character, three different categories of granite gneiss (i.e., highly porphyritic, coarse-grained two micas granite gneiss, medium-grained two micas granite gneiss, and leucocratic tourmaline-bearing muscovite granite gneiss), and granites (i.e., highly porphyritic coarse-grained two micas granite, medium-grained two micas granite, and leucocratic tourmaline-bearing coarse-grained muscovite granite) were classified. Thin section studies show that granite gneiss and granite are formed due to fractional crystallization, as revealed by zoning in plagioclase. The Al saturation index indicates that granite gneiss and granite are strongly peraluminous and S-type. Geochemical analysis shows that all granite gneisses are magnesian except one which is ferroan whereas all granites are ferroan except one which is magnesian. The CaO/Na2O ratio (>0.3) indicates that granitic melt of Jura granite gneiss and granite is pelite-psammite derived peraluminous granitic melt formed due to partial melting of Tanol Formation. The rare earth element (REE) patterns of the Jura granite and Jura granite gneiss indicate that granitic magma of Jura granite and Jura granite gneiss is formed due to partial melting of rocks that are similar in composition to that of upper continental crust. 相似文献
13.
为了探讨韧性剪切带中纳米颗粒的发育过程和形成机制,进而厘定纳米颗粒对韧性剪切带形成过程和应力机制的指示作用,选取了在小妹韧性剪切带里发育的3种岩石样品（花岗岩、花岗质片麻岩和石英片岩）,在扫描电镜下观察其中的纳米颗粒结构及纳米颗粒的聚集形态.观察结果表明:存在2种基本形态——球形的粒状和长条形的柱状,粒状纳米粒子（纳米粒）在3种岩石中都广泛发育,而柱状纳米颗粒（纳米棒）则在花岗质片麻岩中最发育.对纳米颗粒聚集形态研究,可将发育阶段分为:粒化阶段-异化阶段-成层堆积阶段.再次活动时,首先是经过活化阶段,形成复体颗粒,然后再重复上述阶段.结合纳米颗粒形态变化过程,其形成机制可能为脆-韧性变形. 相似文献
14.
15.
Akindele O. Oyinloye 《Journal of African Earth Sciences》1998,26(4):633-641
The basement complex in the Ilesha area consists of two distinct units — the gneisses and the schists. The Ilesha Schist Belt is a back-arc basin where there has been a subduction of an ocean slab into the mantle. This was followed by partial melting of mantle and ocean sediments to generate a wet basaltic magma, as revealed by spidergrams and REE fractionation patterns for the rocks in this belt. In this environment, differentiation of the wet basaltic magma led to the emplacement of a set of rocks, which formed a proto-continent. These rocks were then eroded to generate a sedimentary sequence which was metamorphosed into banded gneiss from which the granite gneisses were derived. The banded gneiss, characterised by alternation of felsic and mafic bands, is composed of medium to very coarse plagioclase, hornblende, quartz and biotite. The granite gneiss, composed of biotite, K--feldspars, quartz and minor garnet, occurs in close association with the banded gneiss.Chemical evidence revealed that elements that are depleted in the banded gneiss are concentrated in the granite gneiss and vice-versa; suggesting a petrogenetic link between these rocks.The schists were deposited as sediments composed of quartz, muscovite, biotite and Fe oxides. These sediments were metamorphosed to form quartzite schists which were folded into the gneisses. After the emplacement of these rocks, there was transpressive tectonic activity in this schist belt, causing deformation of these rocks, and emplacement of the northeast-southwest Ifewara-Zungeru Fault System, which separates the Ilesha Schist Belt into two halves. 相似文献
16.
辽西台里地区花岗质岩石主要由花岗质片麻岩、斑状花岗质片麻岩和黑云母二长花岗岩等组成,这些花岗质岩石均曾被视为新太古代花岗岩。根据各类花岗质岩石的产状序次关系确定,块状/片麻状黑云母二长花岗岩呈岩脉或岩枝状侵入太古宙花岗质片麻岩和斑状花岗质片麻岩中,分别出露于研究区南北两侧。地球化学研究表明,黑云母二长花岗岩属于准铝质-弱过铝质的I型花岗岩,显示火山弧花岗岩的特点。黑云母二长花岗岩中锆石组成复杂,大量继承性锆石和新生锆石共存。新生锆石岩浆结晶特征明显,内部发育振荡生长环带,并具较高的Th/U值（0.15~1.70）。两个样品的新生锆石U-Pb定年结果（加权平均年龄）分别为(153.7±2.0) Ma和(153.7±4.7) Ma。研究表明,黑云母二长花岗岩为源自下地壳中基性火成岩的晚侏罗世花岗质侵入岩,其构造背景与古太平洋板块向亚洲大陆下俯冲作用有关。 相似文献
17.
《Gondwana Research》2002,5(2):401-408
In this paper, field evidence documenting the polydeformed nature of banded gneiss that comprises a part of the Godhra Granite and Gneiss in the southern portion of Aravalli Mountain Belt (AMB), India, is presented. The structural geometry involving an episode of recumbent-reclined folding in the gneiss lying in the vicinity of Devgadh Bariya town is worked out. The banded gneiss occurs as enclaves in the granite. Therefore, it is suggested that the banded gneiss of the region is older than Godhra Granite. Microstructures preserved in the granitic rocks are documented and it is suggested that the granitic rocks underwent deformation and strain during their evolutionary history. Variation in the mesoscopic scale fabric of the gneiss and granite along a south-to-north traverse within the study area is documented, and different possibilities for evolution of Godhra Granite are discussed. 相似文献
18.
Summary The Fracture process zone in compact tension specimens of Indiana limestone was investigated to study its effect on the fracture mechanics parameters in such materials. Specimens were tested up to the peak load, and propagation of the crack from a preexisting notch was monitored. Experiments were designed to study the two features of the fracture process zone in rocks: ligament connections and microcracking.To observe this zone with high sensitivity and accuracy, laser interferometry methods were adopted. Holographic Interferometry was used to observe initial crack propagation. To obtain more quantitative measurements of the displacement field, in realtime, the recently developed technique of electronic speckle pattern interferometry was applied. This technique can provide continuous video recording of the interferometric fringe pattern, depict the evolution of the fracture process, and measure profiles of crack opening displacements.The macroscopic observations of full-field displacement by the laser techniques were supplemented by post mortem observation of the fracture region under a scanning electron microscope. Regions around the crack were studied after the test for possible presence of microcracks.An interactive finite element code was used to compute the stress intensity factors of the propagating crack-tip and displacements. Finite element computations were used to evaluate the effect of the process zone on crack propagation. 相似文献
19.
《International Geology Review》2012,54(10):1194-1211
A belt of khondalite-series rocks in the Western Block of the North China craton (NCC) are considered to represent products of the collision between the north Yinshan and the south Ordos terranes before final amalgamation of the NCC basement. The Jining Complex of Inner Mongolia occurs in the eastern part of the Khondalite Belt and is crosscut by the Trans-North China Orogen. Khondalite rocks of the Jining Complex mainly comprise sillimanite-garnet gneiss, garnet/sillimanite-bearing granite, massive porphyritic granite, garnet quartzite, calc-silicate, and marble with minor felsic gneiss and mafic granulite. LA-ICP-MS, U–Pb dating and cathodoluminescence (CL) image analysis of zircons from five rocks from the complex, i.e. Sil-Bt-Grt leptynite gneiss, Spl-Sil-Ksp-Grt vein in (Crd)-Sil-Grt gneiss, Sil-Grt-K-Fsp mylonite from a shear zone, Crd-bearing Sil-Grt gneiss, and granite were used to determine protolith and metamorphic ages of the khondalite-series rocks. Results of 315 detrital zircon grains indicate five age populations: 2410–2550 Ma, 2162 Ma, 2047–2099 Ma, 1950–1993 Ma, and 1866 Ma. CL investigation reveals that zircon grains of most samples are rounded, unzoned with low Th/U, indicating a metamorphic origin, whereas quite a few grains in some rocks are characterized by magmatic oscillatory zoning and comparatively high Th/U, and are typically overgrown by metamorphic, low CL rims with low Th/U. Three samples of Sil-Bt-Grt gneiss record oldest ages of ～2550–2480 Ma, suggesting an Archaean/early Palaeoproterozoic provenance for the Jining Complex. Ages of ～2162–2047 Ma are interpreted as the metamorphic modified inherited source of supercrustal protoliths of the khondalite-series rocks. The khondalite depositional age is defined as 2228–2027 Ma by concordant ages obtained in this research. The Sil-Ksp-Grt vein and the granite have single population ages of 1985?±?28 Ma and 1957?±?19 Ma, respectively, and are inferred to record the same metamorphic event, i.e. formation of the Khondalite Belt within the Western Block owing to the collision of the north Yinshan and the south Ordos terranes. The Sil-Grt-K-Fsp mylonite yields a single group age of 1866?±?22 Ma, which may date final suturing of the Eastern Block and the Western Block and stabilization of the NCC. 相似文献
20.
湖南上堡矿区钨锡矿成矿条件及找矿前景分析 总被引：1，自引：0，他引：1
上堡矿区出露地层有石炭系和二叠系,壶天群及栖霞组的灰岩、白云质灰岩化学性质活泼.W、Sn含量较高;区内的燕山早期黑云母花岗岩呈岩株或岩枝状产出,岩石具钠长石化和云英岩化,微量元素丰度值高;花岗岩体顶面的洼部构造很发育,规模大,是有利的成矿空间;围岩蚀变强烈,以矽卡岩化为主;W、Sn等元素的土壤异常围绕岩体分布,并且强度大,范围广;经钻探揭露,在接触带上有具工业意义的矽卡岩型钨锡矿体.通过分析,认为上堡矿区成矿地质条件优越,具有大型规模钨锡矿找矿潜力. 相似文献