共查询到20条相似文献，搜索用时 31 毫秒
1.
震电测井的现场试验中测得电磁首波幅值大于伴随电场幅值,这种情况在前人的理论模拟和模型井测量中从未出现.本文研究矿化度界面对震电测井波场的影响,基于Pride方程和边界连续条件模拟了震电测井波场,其中井外孔隙地层可以视为均匀的或者是径向分层的.计算结果表明:对于均匀孔隙地层,当井内流体矿化度大于井外地层孔隙流体矿化度时,电磁首波幅值可以比伴随斯通利波的电场幅值还大;井内流体矿化度与井外地层孔隙流体矿化度的比值越大,电磁首波相对伴随斯通利波的电场的幅值越大.对于径向分层地层,当井内流体矿化度大于内层地层的孔隙流体矿化度时,电磁首波幅值可以比伴随斯通利波的电场幅值还大;当外层地层矿化度小于内层地层矿化度时,电磁首波幅值可以比伴随斯通利波的电场幅值还大;增加内层地层厚度,电场全波幅值减小,电磁首波相对伴随电场的幅值减小.本文的模拟结果表明,震电测井中确实会出现电磁首波幅值比伴随电场幅值还大的情况,这对于解释震电测井的测量结果具有指导意义. 相似文献
2.
Based on the two-dimensional (2D) three-component first-order velocity-stress equation, the high order staggered mesh finite difference numerical simulation method was used to simulate the elastic and viscoelastic tilted transversely isotropic (TTI) media. The perfect matched layer (PML) absorption boundary condition was selected to eliminate the boundary effect. The results show that: ① Under the condition of fixed elastic parameters of elastic TTI medium, when the polarization angle and azimuth are 60° and 45° respectively, the degree of shear wave splitting is significantly greater than the angle of 0°; ② The influence of viscoelasticity on TTI medium is mainly reflected in the amplitude. If the quality factor decreases, the attenuation of the seismic wave amplitude increases, causing the waveform to become wider and distorted. If the quality factor increases, the viscoelastic medium becomes closer to elastic medium; ③ For TTI medium with different polarization angle and azimuth angle in the upper and lower layers, the shear wave can multiple splits at the interface of medium. The symmetry of seismograms is affected by the polarization angle and azimuth angle of TTI medium; ④ Viscoelasticity has a great influence on reflected wave, transmitted wave and converted wave in the low-velocity model. When the viscoelasticity is strong, the weaker waves may not be shown. 相似文献
3.
在油、气储层的勘探和开发中观察到的一个现象是储层岩石中普遍存在孔隙和裂隙.随着近年来孔、裂隙介质弹性波动理论的进展,我们可以将此理论应用于测井技术,以此来指导从声波测井中测量孔、裂隙地层的声学参数.本文计算了孔、裂隙地层里充流体井眼中的多极子声场,分析了声场随裂隙介质的两个主要参数(即裂隙密度和裂隙纵横比)的变化特征.井孔声场的数值计算表明裂隙密度可以大幅度地降低井中声波纵、横波的波速和振幅.随着裂隙密度的增加,在测井频段内也可以看到纵、横波速的频散现象(这种频散在孔隙地层中一般是观察不到的).本文还研究了多极子模式波 (即单极的Stoneley波、伪瑞利波以及偶极的弯曲波)随裂隙参数的变化特征.结果表明,这些模式波的振幅激发和速度频散都受裂隙密度的影响.裂隙密度越高影响越大.此外,裂隙还对模式波的传播造成较大的衰减.相对裂隙密度而言,裂隙纵横比是一个频率控制参数,它控制裂隙对声场影响的频率区间.本文的分析结果对裂缝、孔隙型地层的声波测井具有指导意义. 相似文献
4.
应用三维交错网格应力-速度有限差分方法,数值模拟了含有倾斜裂缝孔隙介质地层中点声源所激发的井孔声场问题.为满足薄裂缝计算需求,开发了不均匀网格有限差分算法,提高了计算精度及计算速度.利用将孔隙介质方程参数取为流体极限的办法来处理裂缝中的流体,实现了流体-孔隙介质界面处的差分方程统一,使界面处的计算更加灵活方便.在验证了方法正确性的基础上,分别考察了单裂缝宽度、裂缝带宽度、裂缝倾斜角度以及孔隙介质渗透率等参数的变化对井轴上阵列波形的影响并进行了分析.结果表明,声波经过裂缝时可能产生反射横波及斯通利波,后者随裂缝宽度的减小而减小,而前者随裂缝宽度的改变,变化不大,在裂缝很小(20μm)时依然存在;裂缝带的宽度、密度越大,反射斯通利波越强;当裂缝(裂缝带)倾斜时,反射横波消失,但反射斯通利波受裂缝倾斜角度的影响较小;渗透率的改变对斯通利波的衰减影响较为明显. 相似文献
5.
本文首先由Christoffel方程推导出黏弹性EDA介质中均匀、 非均匀P波、 SV波和SH波的相速度表达式, 然后参照极端各向异性介质的相关计算方法, 推导出EDA介质中均匀、 非均匀地震波相衰减系数和群衰减系数的表达式, 并通过数值计算分析了相速度、 相衰减系数、 群衰减系数与裂隙方位的关系. 结果表明: 均匀介质中SH波的相速度和相衰减系数均可指示裂隙的走向; 非均匀介质中SH波相衰减系数随非均匀角的增大而增大, 且其对称轴与介质对称轴的夹角也相应增加; 由于地震波振幅的衰减随岩石物理性质的变化比地震波速度的变化更为灵敏, 而且携带了更多的岩石物理性质信息, 因此可用来探明裂隙走向、 密度及含水特性, 进而应用于预测、 预防地下工程地质灾害事故. 相似文献
6.
基于尘埃等离子体Mie-Debye散射模型,研究平衡态下尘埃等离子体中带电尘埃的电磁散射特性.根据输运理论计算高层大气环境中尘埃等离子体层的电磁散射场,给出电磁波垂直入射时尘埃等离子体层的反射函数,同时分析不同浓度、不同粒径分布状态下尘埃等离子体层对电磁波传播的影响.结果表明:尘埃粒子尺度对其电磁散射特性影响非常大;在对数正态分布情况下,当入射波长远大于Debye半径时,尘埃等离子体的散射主要表现为Debye散射,而入射波长远小于Debye半径时,Mie散射占主要部分;并且尘埃等离子体层对电磁波的衰减随尘埃粒子浓度以及尘埃粒子半径的增大而明显增强. 相似文献
7.
本文利用各向异性反射率技术计算理论地震图,提出海底高速薄层会产生沿高速层水平传播的波（简称径向波）,这种波在水层中作为P波,在固液界面激发下行横波,该均匀横波以临界角入射高速薄层,在层内作为超临界角的非均匀横波水平传播,再以临界角转换为上行传播的均匀横波,最终在固液界面上行透射转换为水层中P波.高速薄层传播的径向波不同于界面折射波,也不同于具有频散的面波和通道波.理论地震图的研究表明,径向波具有线性时距,能与海底强反射具有同等振幅水平;径向波有其振幅、时距位置和斜率这些观测记录参数,分别对应高速层的厚度、深度和近似的横波速度;径向波可以克服折射波解释中遇到的振幅强弱和高速层速度等困难.径向波可作为探测海底高速薄层的有力工具,对于研究高速层屏蔽、海底反射类型的多样性和相应的资料处理解释有重要意义. 相似文献
8.
开展复杂低渗储层特征、测井响应及其控制因素分析,有助于储层评价与油水层识别.鄂尔多斯盆地中东部长6期沉积具多物源供给、沉积相带频繁变化的特点,来自不同物源的沉积砂体岩石碎屑成分存在明显差异.长7、长6沉积期盆地周边的火山作用,致使一些地区的长6砂体具有相对高放射性特征.长6储层孔隙类型多样,孔隙结构特征复杂多变,再加上地层水系统的变化,致使一些油区长6低电阻率油层与常规油层、高电阻率水层与常规水层共存.研究结果表明,成藏动力与阻力的对比关系决定了在同一砂体中除存在常规油水分布外,还可能存在油水倒置分布.因此,加强钴前预测、钻井过程监督与调整、钻后综合研究、生产实践检验、解释模型与参数调整、老井复查等,有利于识别油水层,整体把握油水分布规律. 相似文献
9.
10.
11.
Finite‐difference P‐SV simulations of seismic scattering characteristics of faulted coal‐seam models have been undertaken for near‐surface P‐ and S‐wave sources in an attempt to understand the efficiency of body‐wave to channel‐wave mode conversion and how it depends on the elastic parameters of the structure. The synthetic seismograms clearly show the groups of channel waves generated at the fault: one by the downgoing P‐wave and the other by the downgoing S‐wave. These modes travel horizontally in the seam at velocities less than the S‐wavespeed of the rock. A strong Airy phase is generated for the fundamental mode. The velocity contrast between the coal and the host rock is a more important parameter than the density contrast in controlling the amplitude of the channel waves. The optimal coupling from body‐wave energy to channel‐wave energy occurs at a velocity contrast of 1.5. Strong guided waves are produced by the incident S‐sources for source angles of 75° to 90° (close to the near‐side face of the fault). As the fault throw increases, the amplitude of the channel wave also increases. The presence of a lower‐velocity clay layer within the coal‐seam sequence affects the waveguiding characteristics. The displacement amplitude distribution is shifted more towards the lower‐wavespeed layer. The presence of a ‘washout’ zone or a brecciated zone surrounding the fault also results in greater forward scattering and channel‐wave capture by the coal seam. 相似文献
12.
本文首先制作了TI地层模型井,对模型井的速度、密度等物理参数进行了测量,通过快速模拟退火算法得到了该介质的五个TI刚性系数,然后采用缩尺的偶极子探头在HTI地层井孔内进行超声测量实验模拟了实际的偶极子声波测井,并结合数值模拟的结果,研究了不同偏振方向的声源在HTI地层井孔中进行偶极子声波测井的响应特征.模拟结果表明,弯曲波的幅度和速度随声源的偏振方向不同而不同.正交分量的波形幅度在声源偏振方向平行或垂直于快横波面方位时最小,在与快横波面方位呈一定夹角时较大;同向分量波形幅度随声源的偏振方向的变化规律同正交分量相反.弯曲波速度在声源的偏振方向与快横波面方位的夹角小于30°或者大于60°时,分别接近于快弯曲波和慢弯曲波的速度,对于夹角的变化不敏感;当夹角在30°和60°之间时,弯曲波的速度对该夹角变化非常敏感,由接近快弯曲波速度快速变化到接近慢弯曲波速度. 相似文献
13.
过套管电阻率测井是在金属套管井中测量地层电阻率的一种电法测井技术,其测量结果受套管、层厚/围岩、水泥环等井眼环境因素的影响,所以在进行过套管电阻率测井资料解释时必须进行测井环境影响因素校正.本文在论述过套管电阻率测井原理的基础上,针对大庆油田引进的俄罗斯过套管电阻率测井仪器ECOS,分别考察了层厚/围岩、水泥环对测量结果的响应规律,利用正演模拟方法研制完成了层厚/围岩影响校正图版以及水泥环影响校正图版.在计算机上实现了层厚/围岩、水泥环影响校正的算法,并利用模型算例和测井实例验证了本文方法的合理性.该方法能够减少水泥环的影响,提高层厚小于1.0 m薄层电阻率的测量精度,为过套管电阻率测井资料正确解释提供了保障. 相似文献
14.
The conventional acoustic logging interpretation method, which is based on vertical wells that penetrate isotropic formations, is not suitable for horizontal and deviated wells penetrating anisotropic formations. This unsuitability is because during horizontal and deviated well drilling, cuttings will splash on the well wall or fall into the borehole bottom and form a thin bed of cuttings. In addition, the high velocity layers at different depths and intrinsic anisotropy may affect acoustic logging measurements. In this study, we examine how these factors affect the acoustic wave slowness measured in horizontal and deviated wells that are surrounded by an anisotropic medium using numerical simulation. We use the staggered-grid finite difference method in time domain (FDTD) combined with hybrid-PML. First, we acquire the acoustic slowness using a simulated array logging system, and then, we analyze how various factors affect acoustic slowness measurements and the differences between the effects of these factors. The factors considered are high-velocity layers, thin beds of cuttings, dipping angle, formation thickness, and anisotropy. The simulation results show that these factors affect acoustic wave slowness measurements differently. We observe that when the wavelength is much smaller than the distance between the borehole wall and high velocity layer, the true slowness of the formation could be acquired. When the wavelengths are of the same order (i.e., in the near-field scenarios), the geometrical acoustics theory is no longer applicable. Furthermore, when a thin bed of cuttings exists at the bottom of the borehole, Fermat's principle is still applicable, and true slowness can be acquired. In anisotropic formations, the measured slowness changes with increments in the dipping angle. Finally, for a measurement system with specific spacing, the slowness of a thin target layer can be acquired when the distance covered by the logging tool is sufficiently long. Based on systematical simulations with different dipping angles and anisotropy in homogenous TI media, slowness estimation charts are established to quantitatively determine the slowness at any dipping angle and for any value of the anisotropic ratio. Synthetic examples with different acoustic logging tools and different elastic parameters demonstrate that the acoustic slowness estimation method can be conveniently applied to horizontal and deviated wells in TI formations with high accuracy. 相似文献
15.
开发导致的时移地震差异代表了油藏的岩石物理性质变化,本文从差异波形角度出发,明确了声波阻抗界面的反射系数与油层声波阻抗变化之间的函数关系,进而分析薄油层时移地震差异波形特征.通过分析得出,开发前后油层阻抗变化越大,时移地震的差异振幅幅度越大;薄油层的差异波形特征仅与油层的声波阻抗变化有关,油层声波阻抗增大导致与地震子波微分形式相同的差异波形,油层声波阻抗减小产生的差异波形与180°相位的地震子波微分形式相同;油层声波阻抗变化方向导致差异波形振幅幅度变化的快慢. 相似文献
16.
地质成因和构造/热应力导致地壳岩石中的孔隙结构（裂隙和粒间孔）的变化.影响岩石黏弹性的因素包括压力、孔隙度、孔隙中包含的流体和孔隙几何形状等.相对于岩石中的硬孔隙,岩石黏弹性（衰减和频散）受软孔隙（裂隙）的影响更大.本文选取三块白云岩样本,进行了不同围压和流体条件下的超声波实验测量.利用CPEM（Cracks and Pores Effective Medium,裂隙和孔隙有效介质）模型获得了岩石高、低频极限的弹性模量,并通过Zener体（标准线性体）模型将CPEM模型拓展到全频带而得到CPEM-Zener模型,用该模型拟合岩石松弛和非松弛状态下的实验数据,本文得到平均裂隙纵横比和裂隙孔隙度以及纵波速度和品质因子随频率的变化关系.结果表明,饱水岩石的平均裂隙纵横比和裂隙孔隙度均高于饱油岩石,随着压差（围压和孔隙压力的差值）的增加,饱油岩石中的裂隙首先闭合.并且压差在70 MPa以内时,随着压差增大,岩石的平均裂隙纵横比和裂隙孔隙度在饱水和饱油时的差值增大,此时流体类型对于岩石裂隙的影响越来越显著,此外,对饱水岩石,平均裂隙纵横比随压差增加而增大,这可能是由于岩石中纵横比较小的裂隙会随压差增大而逐渐趋于闭合.在饱水和饱油岩石中,裂隙孔隙度和裂隙密度都随着压差增加而减小.通过对裂隙密度和压差的关系进行指数拟合,本文获得压差趋于0时的裂隙密度,且裂隙密度随孔隙度增大而增大,增大速率随压差增加而降低.针对饱水和饱油的白云岩样本,CPEM-Zener模型预测的纵波频散随压差增大而减小,此变化趋势和实验测得的逆品质因子随压差的变化关系基本一致,由此进一步验证了模型的实用性.本研究对岩石的孔隙结构和黏弹性分析以及声波测井、地震勘探的现场应用有指导意义. 相似文献
17.
Most amplitude versus offset (AVO) analysis and inversion techniques are based on the Zoeppritz equations for plane‐wave reflection coefficients or their approximations. Real seismic surveys use localized sources that produce spherical waves, rather than plane waves. In the far‐field, the AVO response for a spherical wave reflected from a plane interface can be well approximated by a plane‐wave response. However this approximation breaks down in the vicinity of the critical angle. Conventional AVO analysis ignores this problem and always utilizes the plane‐wave response. This approach is sufficiently accurate as long as the angles of incidence are much smaller than the critical angle. Such moderate angles are more than sufficient for the standard estimation of the AVO intercept and gradient. However, when independent estimation of the formation density is required, it may be important to use large incidence angles close to the critical angle, where spherical wave effects become important. For the amplitude of a spherical wave reflected from a plane fluid‐fluid interface, an analytical approximation is known, which provides a correction to the plane‐wave reflection coefficients for all angles. For the amplitude of a spherical wave reflected from a solid/solid interface, we propose a formula that combines this analytical approximation with the linearized plane‐wave AVO equation. The proposed approximation shows reasonable agreement with numerical simulations for a range of frequencies. Using this solution, we constructed a two‐layer three‐parameter least‐squares inversion algorithm. Application of this algorithm to synthetic data for a single plane interface shows an improvement compared to the use of plane‐wave reflection coefficients. 相似文献
18.
Effect of crack aperture on P-wave velocity and dispersion 总被引：1，自引：0，他引：1
We experimentally studied the effect of crack aperture on P-wave velocity, amplitude, anisotropy and dispersion. Experimental models were constructed based on Hudson’s theory. Six crack models were embedded with equal-radius penny-shaped crack inclusions in each layer. The P-wave velocity and amplitude were measured parallel and perpendicular to the layers of cracks at frequencies of 0.1 MHz to 1 MHz. The experiments show that as the crack aperture increases from 0.1 mm to 0.34 mm, the amplitude of the P-waves parallel to the crack layers decreases linearly with increasing frequency and the P-wave velocity dispersion varies from 1.5% to 2.1%, whereas the amplitude of the P-wave perpendicular to the crack layers decreases quadratically with increasing frequency and the velocity dispersion varies from 1.9% to 4.7%. The variation in the velocity dispersion parallel and perpendicular to the cracks intensifies the anisotropy dispersion of the P-waves in the crack models (6.7% to 83%). The P-wave dispersion strongly depends on the scattering characteristics of the crack apertures. 相似文献
19.
The phenomenon of an increase in tidal wave height in cone-shaped estuaries is studied. The effect of estuary narrowing in the direction of tidal wave propagation (the hydrodynamic effect of confusor) is among the factors amplifying the tide. An opposite effect of turbulent friction, whose manifestation increases with decreasing bay’s depth, conversely, reduces tide amplitude because of the dissipation of tidal wave energy. Stokes diffusion layer also plays a significant role in the formation of wave transformation regime. In an estuary with a median depth, which is much greater than the Stokes layer thickness, the confusor effect is stronger and tide amplitude increases at estuary head. At depths lesser than Stokes layer thickness, the turbulent friction dominates over the confusor effect and the amplitude of tidal wave decreases at the head of the estuary. The depths of the order of Stokes layer thickness cause an interesting intermediate phenomenon—at the entrance into the estuary, first the effect of friction manifests itself, resulting in a decrease in the amplitude of tidal wave, but later, the effect of confusor starts dominating, and the amplitude of tidal wave again increases toward estuary head. When the period of tidal wave coincides with seiche period, a resonance enhancement of seiche oscillations takes place in the estuary. 相似文献
20.
P. Caillol 《地球物理与天体物理流体动力学》2015,109(2):111-144
In a previous paper, Caillol [Geophys. Astrophys. Fluid Dyn., 2014, 108] investigated the steady nonlinear vortical structure of a singular vortex Rossby mode that has survived to a strong critical-layer-like interaction with a linearly stable, columnar, axisymmetric and dry vortex. We presented a general theory for this wave/mean flow interaction through the nonlinear critical layer theory and calculated the mean azimuthal and axial winds induced at the critical radius at the end of this interaction in the final stage. We here apply that theory to rapidly rotating geophysical vortices: tropical cyclones, cold-air mesocyclones and tornadoes. We find that the numerous assumptions invoked in that paper agree well with the reality of those intense vortices. We also find that in spite of a lack of moist-convection modelling, this dry vortex is fairly well accelerated at the critical radius by such a shear wave with a magnitude of order the square root of the damped-wave amplitude. The intensification level strongly depends on the aspect ratio, height of the system: rapid vortex and parent vortex, over core radius. The thinner the vortex is, the sharper the intensification is. This result is in sharp contrast to the numerous numerical simulations on VR wave/vortex interactions that yield a much smaller intensification of order the square of the wave amplitude. This weakly nonlinear approach nevertheless fails to model small vertical wavelength VR wave/vortex interactions for their related asymptotic expansions are divergent and for they yield strongly nonlinear VR waves coupled with evolving critical layers whose extent can no longer be considered as thin. 相似文献