首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献，搜索用时 31 毫秒
1.
Channel geometry, flow and sedimentation in a meander bend of the River South Esk were studied from bankfull stages (January–February) to low water stages (May) in 1974. Bed topography varied little over the study period, showing a typical pool and ripple geometry. Variation of mean depth and velocity with discharge differed from section to section around the bend, due primarily to locally varying flow resistance with stage. The flow pattern for all stages was dominated by a single spiral over the point bar, with a development zone at the bend entrance. Deviation of bed shear stress from the mean flow direction was in general accord with theory, especially for high stages. The use of a uniform longitudinal water surface slope in the calculation of bed shear stress is not justified because of a complicated water surface topography, also such calculated shear may not represent effective bed shear on grains, as it accounts also for energy losses associated with secondary flows. Dunes covered much of the bar at high stages, with increasing proportions of ripples, sand ribbons and lower phase plane beds at low stages. Local flow resistance generally decreases from dunes, diminished and ripple-backed dunes, ripples, sand ribbons to plane beds, and bed forms are predicted quite well by the stream power-grain size scheme. Mean size, sorting and skewness of sediment over the bed changes little with stage. In general, size decreases, sorting improves and skewness changes from positive to negative from the talweg to the inner bank, and in the downstream direction. Allen's (1970a, b) force balance equation for moving bed load particles is supported for bankfull stage, with some reservations, and textural characteristics are explained by progressive sorting in the direction of sediment transport. Large-scale trough cross stratification (with some flat bedding) formed at high stage by dunes (and lower phase plane beds) dominates the point bar sediments. Alternations of fine-medium sand (often cross-laminated) and vegetation-rich layers result from periodic deposition on the grassed upper bar surface. Fining upwards sequences produced by lateral channel migration are modified by a coarsening upward subsequence in the upstream bar region where spiral flow is developing from the bend upstream.  相似文献   

2.
The permeability of river beds is an important control on hyporheic flow and the movement of fine sediment and solutes into and out of the bed. However, relatively little is known about the effect of bed permeability on overlying near‐bed flow dynamics, and thus on fluid advection at the sediment–water interface. This study provides the first quantification of this effect for water‐worked gravel beds. Laboratory experiments in a recirculating flume revealed that flows over permeable beds exhibit fundamental differences compared with flows over impermeable beds of the same topography. The turbulence over permeable beds is less intense, more organised and more efficient at momentum transfer because eddies are more coherent. Furthermore, turbulent kinetic energy is lower, meaning that less energy is extracted from the mean flow by this turbulence. Consequently, the double‐averaged velocity is higher and the bulk flow resistance is lower over permeable beds, and there is a difference in how momentum is conveyed from the overlying flow to the bed surface. The main implications of these results are three‐fold. First, local pressure gradients, and therefore rates of material transport, across the sediment–water interface are likely to differ between impermeable and permeable beds. Second, near‐bed and hyporheic flows are unlikely to be adequately predicted by numerical models that represent the bed as an impermeable boundary. Third, more sophisticated flow resistance models are required for coarse‐grained rivers that consider not only the bed surface but also the underlying permeable structure. Overall, our results suggest that the effects of bed permeability have critical implications for hyporheic exchange, fluvial sediment dynamics and benthic habitat availability. © 2017 The Authors. Earth Surface Processes and Landforms published by John Wiley & Sons Ltd.  相似文献   

3.
Bedload, the transport of sediment remaining in contact with the stream bed, has mainly been studied from the perspective of the correlation between fluid driving forces and the responding sediment flux. Yet grain–grain interactions are important and bedload should also be considered as a granular phenomenon. We review progress made recently in the study of granular flows, especially on segregation and rheology, that better illuminates the nature of bedload. Granular flows may exhibit gas‐like or fluid‐like flow, or quasi‐solid deformation. All three conditions might be duplicated in bedload. Understanding of intense bedload transport occurring continuously in a layer several grains deep – typical of sand beds – might greatly benefit from results in granular physics, as illustrated by grain‐inspired bedload results. However, processes restricted to the surface of the bed, when particles move intermittently and the bed becomes structured, while characteristic in gravel‐bed channels, are not well addressed in granular physics. Mutual study of these phenomena may benefit both physics and fluvial geomorphology. We intend, therefore, to contribute to an enhanced dialogue between granular physics and bedload science communities. Copyright © 2010 John Wiley & Sons, Ltd.  相似文献   

4.
This paper presents the predicted flow dynamics from the application of a Reynolds‐averaged Navier–Stokes model to a series of bifurcation geometries with morphologies measured during previous flume experiments. The topography of the bifurcations consists of either plane or bedform‐dominated beds which may or may not possess discordance between the two bifurcation distributaries. Numerical predictions are compared with experimental results to assess the ability of the numerical model to reproduce the division of flow into the bifurcation distributaries. The hydrodynamic model predicts: (1) diverting fluxes in the upstream channel which direct water into the distributaries; (2) super‐elevation of the free surface induced at the bifurcation edge by pressure differences; and (3) counter‐rotating secondary circulation cells which develop upstream of the apex of the bifurcation and move into the downstream channels, with water converging at the surface and diverging at the bed. When bedforms are not present, weak transversal fluxes characterize the upstream channel for almost its entire length, associated with clearly distinguishable secondary circulation cells, although these may be under‐estimated by the turbulence model used in the solution. In the bedform dominated case, the same hydrodynamic conditions were not observed, with the bifurcation influence restricted and depth scale secondary circulation cells not forming. The results also demonstrate the dominant effect bed discordance has upon flow division between the two distributaries. Finally, results indicate that in bedform dominated rivers. Consequently, we suggest that sand‐bed river bifurcations are more likely to have an influence that extends much further upstream and have a greater impact upon water distribution. This may contribute to observed morphological differences between sand‐bedded and gravel‐bedded braided river networks. Copyright © 2012 John Wiley & Sons, Ltd.  相似文献   

5.
The Reynolds stress and bed shear stress are important parameters in fluvial hydraulics. Steady-nonuniform flow in open channels with streamwise sloping beds having upward seepage through loose beds is theoretically analyzed to estimate the Reynolds stress and bed shear stress. Equations of the Reynolds stress and bed shear stress are developed, assuming a modified logarithmic velocity distribution law due to upward seepage, and using the Reynolds and continuity equations of two-dimensional flow in open channels.  相似文献   

6.
This paper presents an approach to modeling the depth-averaged velocity and bed shear stress in compound channels with emergent and submerged vegetation. The depth-averaged equation of vegetated compound channel flow is given by considering the drag force and the blockage effect of vegetation, based on the Shiono and Knight method (1991) [40]. The analytical solution to the transverse variation of depth-averaged velocity is presented, including the effects of bed friction, lateral momentum transfer, secondary flows and drag force due to vegetation. The model is then applied to compound channels with completely vegetated floodplains and with one-line vegetation along the floodplain edge. The modeled results agree well with the available experimental data, indicating that the proposed model is capable of accurately predicting the lateral distributions of depth-averaged velocity and bed shear stress in vegetated compound channels with secondary flows. The secondary flow parameter and dimensionless eddy viscosity are also discussed and analyzed. The study shows that the sign of the secondary flow parameter is determined by the rotational direction of secondary current cells and its value is dependent on the flow depth. In the application of the model, ignoring the secondary flow leads to a large computational error, especially in the non-vegetated main channel.  相似文献   

7.
Mass exchange between debris flow and the bed plays a vital role in debris flow dynamics. Here a depth‐averaged two‐phase model is proposed for debris flows over erodible beds. Compared to previous depth‐averaged two‐phase models, the present model features a physical step forward by explicitly incorporating the mass exchange between the flow and the bed. A widely used closure model in fluvial hydraulics is employed to estimate the mass exchange between the debris flow and the bed, and an existing relationship for bed entrainment rate is introduced for comparison. Also, two distinct closure models for the bed shear stresses are evaluated. One uses the Coulomb friction law and Manning's equation to determine the solid and fluid resistances respectively, while the other employs an analytically derived formula for the solid phase and the mixing length approach for the fluid phase. A well‐balanced numerical algorithm is applied to solve the governing equations of the model. The present model is first shown to reproduce average sediment concentrations in steady and uniform debris flows over saturated bed as compared to an existing formula underpinned by experimental datasets. Then, it is demonstrated to perform rather well as compared to the full set of USGS large‐scale experimental debris flows over erodible beds, in producing debris flow depth, front location and bed deformation. The effects of initial conditions on debris flow mass and momentum gain are resolved by the present model, which explicitly demonstrates the roles of the wetness, porosity and volume of bed sediments in affecting the flow. By virtue of extended modeling cases, the present model produces debris flow efficiency that, as revealed by existing observations and empirical relations, increases with initial volume, which is enhanced by mass gain from the bed. Copyright © 2017 John Wiley & Sons, Ltd.  相似文献   

8.
Debris flows can grow greatly in size by entrainment of bed material, enhancing their runout and hazardous impact. Here, we experimentally investigate the effects of debris‐flow composition on the amount and spatial patterns of bed scour and erosion downstream of a fixed to erodible bed transition. The experimental debris flows were observed to entrain bed particles both grain by grain and en masse, and the majority of entrainment was observed to occur during passage of the flow front. The spatial bed scour patterns are highly variable, but large‐scale patterns are largely similar over 22.5–35° channel slopes for debris flows of similar composition. Scour depth is generally largest slightly downstream of the fixed to erodible bed transition, except for clay‐rich debris flows, which cause a relatively uniform scour pattern. The spatial variability in the scour depth decreases with increasing water, gravel (= grain size) and clay fraction. Basal scour depth increases with channel slope, flow velocity, flow depth, discharge and shear stress in our experiments, whereas there is no correlation with grain collisional stress. The strongest correlation is between basal scour and shear stress and discharge. There are substantial differences in the scour caused by different types of debris flows. In general, mean and maximum scour depths become larger with increasing water fraction and grain size, and decrease with increasing clay content. However, the erodibility of coarse‐grained experimental debris flows (gravel fraction = 0.64) is similar on a wide range of channel slopes, flow depths, flow velocities, discharges and shear stresses. This probably relates to the relatively large influence of grain‐collisional stress to the total bed stress in these flows (30–50%). The relative effect of grain‐collisional stress is low in the other experimental debris flows (<5%), causing erosion to be largely controlled by basal shear stress. Copyright © 2016 John Wiley & Sons, Ltd.  相似文献   

9.
When sediment grains are transported as bed load in overland flow, there is a net transfer of momentum from the flow to the grains. When these grains collide with other grains, whether on the bed or in the flow, streamwise flow velocity decreases and resistance to flow increases. Resistance to flow generated in this manner is termed bed‐load transport resistance. Resistance to flow f over a plane bed may be partitioned into grain resistance fg and bed‐load transport resistance fbt. We use the symbols fbtf and fbtm to denote fbt for flows over fixed beds and over mobile beds, respectively, and we compute the effect of bed mobility on flow resistance fmob by subtracting fbtf from fbtm. The data for this study come from 54 flume experiments with fixed beds and 38 with mobile beds. On average fmob is approximately equal to half of fbtm, which is about one‐quarter of f. Hence, fmob is about one‐tenth of f. Predictive equations are developed for fbtf, fbtm and fmob using dimensional analysis to identify the relevant independent variables and regression analysis to evaluate the coefficients associated with these variables. Values of fmob are always positive which implies that mobile beds offer greater resistance to flow than do fixed beds. Evidently bed‐load grains colliding with mobile beds lose more momentum to the bed than do grains colliding with fixed beds. In other words, grain collisions with mobile beds are less elastic than those with fixed beds. Copyright © 2005 John Wiley & Sons, Ltd.  相似文献   

10.
《国际泥沙研究》2020,35(6):609-620
The fluvial geomorphology in tectonically active (particularly rapid uplift) regions often undergoes continuous change. The rapid uplift is coincident with high erosion rates; consequently, incised valleys are formed. Mass flows (for example, avalanches, landslides, and debris flows) in incised valleys can markedly influence fluvial processes and even reshape valley geomorphology. However, these processes and long-term evolution corresponding to mass flows require further clarification. Field campaigns were carried out in the region near the Yigong Tsangpo and Palong Tsangpo Rivers (hereafter the Yigong and Palong Rivers), the two largest tributaries of the lower Yarlung Tsangpo River, to examine the feedback between fluvial processes and mass flows. Remote sensing images from recent decades were used to compare the channel morphology before and after typical mass flows (particularly catastrophic ones). The morphology of the lower Yigong River has evidently been impacted by landslides, while that of the Palong River has mainly been shaped by glacial processes and debris flows. At present, the morphology of the latter consists of alternating sections of gorges and wide valleys, with a staircase-like longitudinal profile. The gorge sections exhibit single and deeply incised channels with a high-gradient channel bed and terraces. In contrast, the wide valley sections consist of lakes, braided or anabranching channels, gentle bed gradients, and thick alluvial deposits. Debris flows occur more frequently in gullies in the reaches of the gorge sections and rarely in gullies along the wide valley sections. The occurrence of mass flow events has resulted in an imbalance of the previous (quasi-)equilibrium in the river morphology; however, this has triggered negative feedback that is driving the transient river morphology to a new state of (quasi-)equilibrium.  相似文献   

11.
Particle dynamics are investigated experimentally in supercritical high‐speed open channel flow over a fixed planar bed of low relative roughness height simulating flows in high‐gradient non‐alluvial mountain streams and hydraulic structures. Non‐dimensional equations were developed for transport mode, particle velocity, hop length and hop height accounting for a wide range of literature data encompassing sub‐ and supercritical flow conditions as well as planar and alluvial bed configurations. Particles were dominantly transported in saltation and particle trajectories on planar beds were rather flat and long compared with alluvial bed data due to (1) increased lift forces by spinning motion, (2) strongly downward directed secondary currents, and (3) a planar flume bed where variation in particle reflection and damping effects were minor. The analysis of particle saltation trajectories revealed that the rising and falling limbs were almost symmetrical contradicting alluvial bed data. Furthermore, no or negligible effect of particle size and shape on particle dynamics were found. Implications of experimental findings for mechanistic saltation‐abrasion models are briefly discussed. Copyright © 2017 John Wiley & Sons, Ltd.  相似文献   

12.
Existing numerical investigations of dam-break flows rarely consider the effects of vegetation.This paper presents a depth-averaged two-dimensional model for dam-break flows over mobile and vegetated beds.In the model,both the consequences of reducing space for storing mass and momentum by the existence of vegetation and dragging the flow are considered:the former is considered by introducing a factor (1-c) to the flow depth,where c is the vegetation density;the later is considered by including an additional sink term in the momentum equations.The new governing equations are discretized by the finite volume method;and an existing second-order central-upwind scheme embedded with the hydrostatic reconstruction method for water depth,is used to estimate the fluxes;the source terms are estimated by either explicit or semi-explicit methods fulfilling the stability requirement.Laboratory experiments of dam-break flows or quasi-steady flows with/without vegetation effects/sediment transport are simulated.The good agreements between the measurements and the numerical simulations demonstrate a satisfactory performance of the model in reproducing the flow depth,velocity and bed deformation depth.Numerical case studies of six scenarios of dam-break flows over a mobile and vegetated bed are conducted.It is shown that when the area of the vegetation zone,the vegetation density,and the pattern of the vegetation distribution are varied,the resulted bed morphological change differs greatly,suggesting a great influence of vegetation on the dam-break flow evolution.Specifically,the vegetation may divert the direction of the main flow,hindering the flow and thus result in increased deposition upstream of the vegetation.  相似文献   

13.
Modelling dam-break flows over mobile beds using a 2D coupled approach   总被引：1，自引：0，他引：1  
Dam-break flows usually propagate along rivers and floodplains, where the processes of fluid flow, sediment transport and bed evolution are closely linked. However, the majority of existing two-dimensional (2D) models used to simulate dam-break flows are only applicable to fixed beds. Details are given in this paper of the development of a 2D morphodynamic model for predicting dam-break flows over mobile beds. In this model, the common 2D shallow water equations are modified, so that the effects of sediment concentrations and bed evolution on the flood wave propagation can be considered. These equations are used together with the non-equilibrium transport equations for graded sediments and the equation of bed evolution. The governing equations are solved using a matrix method, thus the hydrodynamic, sediment transport and morphological processes can be jointly solved. The model employs an unstructured finite volume algorithm, with an approximate Riemann solver, based on the Roe-MUSCL scheme. A predictor–corrector scheme is used in time stepping, leading to a second-order accurate solution in both time and space. In addition, the model considers the adjustment process of bed material composition during the morphological evolution process. The model was first verified against results from existing numerical models and laboratory experiments. It was then used to simulate dam-break flows over a fixed bed and a mobile bed to examine the differences in the predicted flood wave speed and depth. The effects of bed material size distributions on the flood flow and bed evolution were also investigated. The results indicate that there is a great difference between the dam-break flow predictions made over a fixed bed and a mobile bed. At the initial stage of a dam-break flow, the rate of bed evolution could be comparable to that of water depth change. Therefore, it is often necessary to employ the turbid water governing equations using a coupled approach for simulating dam-break flows.  相似文献   

14.
The acceleration of saltating grains by overland flow causes momentum to be transferred from the flow to the grains, thereby increasing flow resistance and bed roughness. To assess the impact of saltating sediment on overland flow hydraulics, velocity profiles in transitional and turbulent flows on a fixed sand-covered bed were measured using hot-film anemometry. Five discharges were studied. At each discharge, three flows were measured: one free of sediment, one with a relatively low sediment load, and one with a relatively high sediment load. In these flows from 83 to 90 per cent of the sediment was travelling by saltation. As a result, in the sediment-laden flows the near-bed velocities were smaller and the velocity profiles steeper than those in the equivalent sediment-free flows. Sediment loads ranged up to 87·0 per cent of transport capacity and accounted for as much as 20·8 per cent of flow resistance (measured by the friction factor) and 89·7 per cent of bed roughness (measured by the ratio of the roughness length to median grain diameter). It is concluded that saltating sediment has a considerable impact on overland flow hydraulics, at least on fixed granular beds. Saltation is likely to have a relatively smaller effect on overland flow on natural hillslopes and agricultural fields where form and wave resistance dominate. Still, saltation is generally of greater significance in overland flow than in river flow, and for this reason its effect on overland flow hydraulics is deserving of further study. © 1998 John Wiley & Sons, Ltd.  相似文献   

15.
  相似文献   

16.
An investigation has been conducted to identify the key parameters that are likely to scale laboratory sediment deposits to the field scale. Two types of bed formation were examined: one where sediment is manually placed and screeded and the second where sediment is fed into a running flume. This later technique created deposits through sequential cycles of sediment transport and deposition. Detailed bed surface topography measurements have been made over a screeded bed and three fed beds. In addition, bulk subsurface porosity and hydraulic conductivity have been measured. By comparing the four beds, results revealed that certain physical properties of the screeded bed were clearly different from those of the fed beds. The screeded bed had a random organization of grains on both the surface and within the subsurface. The fed beds exhibited greater surface and subsurface organization and complexity, and had a number of properties that closely resembled those found for water‐worked gravel beds. The surfaces were water‐worked and armoured and there was preferential particle orientation and direction of imbrication in the subsurface. This suggested that fed beds are able to simulate, in a simplified manner, both the surface and subsurface properties of established gravel‐bed river deposits. The near‐bed flow properties were also compared. It revealed that the use of a screeded bed will typically cause an underestimation in the degree of temporal variability in the flow. Furthermore, time‐averaged streamwise velocities were found to be randomly organized over the screeded bed but were organized into long streamwise flow structures over the fed beds. It clearly showed that caution should be taken when comparing velocity measurements over screeded beds with water‐worked beds, and that the formation of fed beds offers an improved way of investigating intragravel flow and sediment–water interface exchange processes in gravel‐bed rivers at a laboratory scale. Copyright © 2008 John Wiley & Sons, Ltd.  相似文献   

17.
  相似文献   

18.
In the Dolomitic region, abundant coarse hillslope sediment is commonly found at the toe of rocky cliffs. Ephemeral channels originate where lower permeability bedrock surfaces concentrate surface runoff. Debris flows initiate along such channels following intense rainfall and determine the progressive erosion and deepening of the channels. Sediment recharge mechanisms include rock fall, dry ravel processes and channel-bank failures. Here we document debris flow activity that took place in an active debris flow basin during the year 2015. The Cancia basin is located on the southwestern slope of Mount Antelao (3264 m a.s.l.) in the dolomitic region of the eastern Italian Alps. The 2.5 km2 basin is incised in dolomitic limestone rocks. The data consist of repeated topographic surveys, distributed rainfall measurements, time-lapse (2 s) videos of two events and pore pressure measurements in the channel bed. During July and August 2015, two debris flow events occurred, following similarly intense rainstorms. We compared rainfall data to existing rainfall triggering thresholds and simulated the hydrological response of the headwater catchment with a distributed model in order to estimate the total and peak water discharge. Our data clearly illustrate how debris entrainment along the channel is the main contributor to the overall mobilized volume and that erosion is dominant when the channel slope exceeds 16°. Further downstream, sediment accumulation and depletion occurred alternately for the two successive events, indicating that sediment availability along the channel also influences the flow behaviour along the prevailing-transport reach. The comparison between monitoring data, topographical analysis and hydrological simulation allows the estimation of the average solid concentration of the two events and suggests that debris availability has a significant influence on the debris flow volume. © 2020 John Wiley & Sons, Ltd.  相似文献   

19.
The present experimental investigation focuses on the characteristics of near bed turbulence in a fully rough, uniform open-channel flow over a gravel-type bed. Due to bed topography small scale heterogeneity, the flow is not uniform locally in the near bed region and a double averaging methodology is applied over a length scale much larger than the gravel size. The double-averaged Turbulent Kinetic Energy (TKE) budget derived in the context of the present flow over a gravel bed differs from the TKE budget written for flow over a vegetation canopy. The non-constant shape of the roughness function measured in our gravel bed leads to an additional bed-induced production term which is null for vertical roughness elements, such as simplified vegetation elements. The experimental estimation of the terms of the TKE budget reveals that the maximum turbulent activity takes place away from the reference plane, near the roughness crests. However, within the interface sublayer the work of the bed induced velocity fluctuations against the Reynolds stress is of the same magnitude as the main turbulence production term. Consequently, the characteristics of the TKE budget have similarities with uniform flows over canopies and strongly differ from uniform flows over smooth and transitionally rough flows over sedimentlike beds.  相似文献   

20.
The formation of landslide dams is often induced by earthquakes in mountainous areas.The failure of a landslide dam typically results in catastrophic flash floods or debris flows downstream.Significant attention has been given to the processes and mechanisms involved in the failure of individual landslide dams.However,the processes leading to domino failures of multiple landslide dams remain unclear.In this study,experimental tests were carried out to investigate the domino failure of landslide dams and the consequent enlargement of downstream debris flows.Different blockage conditions were considered,including complete blockage,partial blockage and erodible bed（no blockage）.The mean velocity of the flow front was estimated by videos.Total stress transducers（TSTs）and Laser range finders（LRFs） were employed to measure the total stress and the depth of the flow front,respectively.Under a complete blockage pattern,a portion of the debris flow was trapped in front of each retained landslide dam before the latter collapsed completely.This was accompanied by a dramatic decrease in the mean velocity of the flow front.Conversely,under both partial blockage and erodible bed conditions,the mean velocity of the flow front increased gradually downward along the sloping channel.Domino failures of the landslide dams were triggered when a series of dams（complete blockage and partial blockage） were distributed along the flume.However,not all of these domino failures led to enlarged debris flows.The modes of dam failures have significant impacts on the enlargement of debris flows.Therefore,further research is necessary to understand the mechanisms of domino failures of landslide dams and their effects on the enlargement of debris flows.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号