共查询到20条相似文献，搜索用时 31 毫秒
1.
I used theoretical forward models to show that a cavity embedded in a stratified sedimentary sequence can induce an equivalence problem in the ERT data inversion. Conductive top soil increases the misfit between the ground feature and the ERT model. The misfit depends on array and stratigraphy sequences. The latter induce an equivalence problem that manifests itself as wrong cavity depth positioning. The misfit is greater in the data acquired with Schlumberger array than with dipole–dipole.The ambiguity of ERT data inversion problems was tested in the detection of cavities linked to an 8th–6th century B.C. Sabine tomb, 3 m wide × 3 m long × 2 m high, excavated from a shaly gray volcanic ash (cinerite) layer covered by semi-lithoid tuff and top soil layers. In the real study I reduced the ambiguity in the inverse problem of ERT data using a priori information on geometry and resistivity of the cavity. The constrains were carried out from georadar data acquired with 80 and 200 MHz antenna. I demonstrate that this procedure has a practical application in cavity detection, and is a key to the reduction of the uncertainty inherent in the inversion process of ERT data. 相似文献
2.
Inversion of resistivity in Magnetic Resonance Sounding 总被引：3，自引：0，他引：3
Magnetic Resonance Sounding (MRS, or Surface Nuclear Magnetic Resonance - SNMR) is used for groundwater exploration and aquifer characterization. Since this is an electromagnetic method, the excitation magnetic field depends on the resistivity of the subsurface. Therefore, the resistivity has to be taken into account in the inversion: either as a priori information or as an inversion parameter during the inversion process, as introduced in the presented paper. Studies with synthetic data show that water content and resistivity can be resolved for a low resistive aquifer even using only the amplitude of the MRS signal. However, the inversion result can be significantly improved using amplitude and phase of the MRS signal. The successful implementation of the inversion for field data shows that the resistivities derived from MRS are comparable to those from conventional geoelectric methods such as DC resistivity and transient electromagnetic. By having information about both the resistivity and the water content, MRS inversions give information about the quality of the water in the aquifer. This is of utmost interest in hydrogeological studies as this specific information cannot be determined solely by geoelectric measurements, due to the nonunique dependence of resistivity on water content and salinity. 相似文献
3.
Bernhard Siemon Esben Auken Anders Vest Christiansen 《Journal of Applied Geophysics》2009,67(3):259-268
Helicopter-borne frequency-domain electromagnetic (HEM) surveys are used for fast high-resolution, three-dimensional resistivity mapping. Standard interpretation tools are often based on layered earth inversion procedures which, in general, explain the HEM data sufficiently. As a HEM system is moved while measuring, noise on the data is a common problem. Generally, noisy data will be smoothed prior to inversion using appropriate low-pass filters and consequently information may be lost.For the first time the laterally constrained inversion (LCI) technique has been applied to HEM data combined with the automatic generation of dynamic starting models. The latter is important because it takes the penetration depth of the electromagnetic fields, which can heavily vary in survey areas with different geological settings, into account. The LCI technique, which has been applied to diverse airborne and ground geophysical data sets, has proven to be able to improve the HEM inversion results of layered earth structures. Although single-site 1-D inversion is generally faster and — in case of strong lateral resistivity variations — more flexible, LCI produces resistivity — depth sections which are nearly identical to those derived from noise-free data.The LCI results are compared with standard single-site Marquardt–Levenberg inversion procedures on the basis of synthetic data as well as field data. The model chosen for the generation of synthetic data represents a layered earth structure having an inhomogeneous top layer in order to study the influence of shallow resistivity variations on the resolution of deep horizontal conductors in one-dimensional inversion results. The field data example comprises a wide resistivity range in a sedimentary as well as hard-rock environment.If a sufficient resistivity contrast between air and subsurface exists, the LCI technique is also very useful in correcting for incorrect system altitude measurements by using the altitude as a constrained inversion parameter. 相似文献
4.
5.
Out‐of‐plane effects in 2D borehole‐to‐surface resistivity tomography and applications in mineral exploration 
下载免费PDF全文
下载免费PDF全文 In this paper, we discuss the effects of anomalous out‐of‐plane bodies in two‐dimensional (2D) borehole‐to‐surface electrical resistivity tomography with numerical resistivity modelling and synthetic inversion tests. The results of the two groups of synthetic resistivity model tests illustrate that anomalous bodies out of the plane of interest have an effect on two‐dimensional inversion and that the degree of influence of out‐of‐plane body on inverted images varies. The different influences are derived from two cases. One case is different resistivity models with the same electrode array, and the other case is the same resistivity model with different electrode arrays. Qualitative interpretation based on the inversion tests shows that we cannot find a reasonable electrode array to determine the best inverse solution and reveal the subsurface resistivity distribution for all types of geoelectrical models. Because of the three‐dimensional effect arising from neighbouring anomalous bodies, the qualitative interpretation of inverted images from the two‐dimensional inversion of electrical resistivity tomography data without prior information can be misleading. Two‐dimensional inversion with drilling data can decrease the three‐dimensional effect. We employed two‐ and three‐dimensional borehole‐to‐surface electrical resistivity tomography methods with a pole–pole array and a bipole–bipole array for mineral exploration at Abag Banner and Hexigten Banner in Inner Mongolia, China. Different inverse schemes were carried out for different cases. The subsurface resistivity distribution obtained from the two‐dimensional inversion of the field electrical resistivity tomography data with sufficient prior information, such as drilling data and other non‐electrical data, can better describe the actual geological situation. When there is not enough prior information to carry out constrained two‐dimensional inversion, the three‐dimensional electrical resistivity tomography survey is the better choice. 相似文献
6.
2.5维井间电磁反演在中国东部孤岛油田的应用 总被引：3，自引：1，他引：2
In this study, we present a practical technique of transforming cross-hole EM data into the inter-well resistivity distribution. The a priori information constraint is incorporated into an iterative regularized inversion procedure and a variable roughness is added into the inversion process. Finite element approximation based on a two and a half-dimensional （2.5D） model has been developed for the forward problem and the ＂pseudo-forward＂ problem needed for constructing the sensitivity matrix and synthetic data set. The regularized least-squares inversion scheme, constrained with the a priori information obtained from well logs, was adopted to reconstruct the inter-well resistivity profile from two synthetic electromagnetic data sets and field data acquired in the Gudao Oil Field, East China. The partial derivatives of the sensitivity matrix were computed by the adjoint equation based on the reciprocity principle. Inversion results of the synthetic and field data examples suggest that our method is robust and stable in the presence of random noise in the field data and can be used for cross-hole EM field data interpretation. 相似文献
7.
椭圆极化现象是电磁场在导电介质中传播时产生的,为得到准确的相位信息,在计算激发磁场时应考虑椭圆极化。本文研究了地面核磁共振(SNMR)信号相位求取电阻率的基本方法,利用SNMR信号通过广义逆反演法得到电阻率未知情况下的含水率及层位分布,作为相位反演电阻率的先验值,通过模拟退火法实现对电阻率的反演。对SNMR的研究解决了通过相位对电阻率的求取,有利于进一步利用相位信息提高含水层和含水率反演的精度。 相似文献
8.
本文提出了一维垂直各向异性(VTI)介质倾斜偶极源频率域海洋可控源电磁(CSEM)资料高斯-牛顿反演方法.在电阻率各向异性介质水平偶极源和垂直偶极源海洋CSEM正演算法的基础上,利用欧拉旋转方法,实现了各向异性介质倾斜偶极源海洋CSEM正演算法.海洋可控源电磁场关于地下介质横向电阻率(ρ_h)和垂向电阻率(ρ_v)的偏导数(即灵敏度矩阵)是解析计算的,结合垂直各向异性介质横向电阻率与垂向电阻率的关系,将各向异性率融入到正则化因子选择中,实现了正则化因子的自适应选择.理论模型合成数据和实测资料反演算例表明,我们提出的反演方法能够较准确的重构海底围岩和基岩的各向异性电阻率以及高阻薄层的埋藏深度、厚度和垂向电阻率. 相似文献
9.
Resistivity in horizontal boreholes can give useful detailed information about the geological conditions for construction in rock, i.e. in front of a tunnel bore machine. This paper is an attempt to identify a suitable methodology for an effective measuring routine for this type of geophysical measurements under actual construction site conditions.Prior to any measurements numerical modelling was done in order to evaluate the resolution of different electrode arrays. Four different arrays were tested; dipole–pole, cross-hole dipole–dipole, cross-hole pole–tripole and multiple gradient array. Additionally the resolution of a combination of cross-hole dipole–dipole and multiple gradient was assessed. The 2D sensitivity patterns for various arrangements of the cross-hole dipole–dipole and multiple gradient array were examined. The sensitivity towards inaccurate borehole geometry and the influence of water in the boreholes were also investigated. Based on the model study the cross-hole dipole–dipole array, multiple gradient array and a combination of these were found to give the best result and therefore were used for test measurements in horizontal boreholes. The boreholes were 28.5 m long and drilled 6.5 m apart. Prototypes of semi-rigid borehole cables made it possible to insert multi electrode cables in an efficient way, allowing fast measurement routines. These measurements were then studied to determine their accuracy and applicability. The results showed a high resistivity rock mass at the site. A transition from high resistivity to slightly lower resistivity coincides well with a change in lithology from gneiss-granite to gneiss. It is likely that the shotcrete on the tunnel wall is seen as a low resistivity zone.The measurements are a valuable tool, but further development of the cables and streamlining of measuring routines have to be performed before the resistivity tomography can be used routinely in pilot holes during construction in rocks. 相似文献
10.
A method of detecting lateral resistivity inhomogeneities with a multi-electrode cable for the Schlumberger array is presented. Using such a cable system, two dipole-dipole soundings are gathered in addition to the Schlumberger sounding at each point. Offset differences calculated from the dipole-dipole data give qualitative information about lateral resistivity inhomogeneities. Results from 1D modelling can give quantitative information about the 2D resistivity distribution since the dipole-dipole soundings are made to either side of the Schlumberger sounding point. Examples from two different locations in Norway are shown. At Reinøya, northern Norway, a dipping layer, confirmed by refraction seismic data, was identified. In a sedimentary basin with a contamination plume at Haslemoen, southern Norway, the method has revealed lateral variations in resistivity. In both cases, the Schlumberger soundings could be fitted with a 1D resistivity model. 相似文献
11.
基于光滑约束的最小二乘法是三维电阻率反演的主要方法,但该方法在某些情况下存在着多解性较强的问题,且普遍耗时较长,严重制约了三维反演方法的推广与发展.为改善上述问题,将表征模型参数变化范围的不等式约束作为先验信息引入最小二乘线性反演方法中,有效地改善了反演结果的精度,降低了反演的多解性问题.为了解决耗时较长的问题,基于预条件共轭梯度(PCG)算法和Cholesky分解法的特点提出了一套优化三维电阻率反演计算效率的计算方案.在该方案中,Cholesky分解法被用来求解敏感度矩阵计算中的多个点源场的正演问题,Cholesky分解法只需对总体系数矩阵进行一次分解,然后对不同的右端向量进行回代即可.将预条件共轭梯度法引入到三维电阻率反演方程的求解中,将雅可比迭代中的对角阵作为预处理矩阵,其具有求逆方便、无需内存空间的特点,有效地加快了收敛速度.对合成数据以及实测数据的反演算例表明,借助不等式约束和反演效率优化方案,最小二乘反演方法可得到较为精确的反演结果,有效地提高了反演计算效率,具有良好的推广前景. 相似文献
12.
Airborne electromagnetic (AEM) surveys are currently being flown over populated areas and applied to detailed problems using high flight line densities. Interpretation information is supplied through a model of the subsurface resistivity distribution. Theoretical and survey data are used here to study the character and reliability of such models. Although the survey data were obtained using a fixed-wing system, the corresponding associations with helicopter, towed-bird systems are discussed. Both Fraser half-space and 1D inversion techniques are considered in relation to their ability to distinguish geological, cultural and environmental influences on the survey data. Fraser half-space modelling provides the dual interpretation parameters of apparent resistivity and apparent depth at each operational frequency. The apparent resistivity was found to be a remarkably stable parameter and appears robust to the presence of a variety of at-surface cultural features. Such features provide both incorrect altitude data and multidimensional influences. Their influences are observed most strongly in the joint estimate of apparent depth and this accounts for the stability of the apparent resistivity. Positive apparent depths, in the example data, result from underestimated altitude measurements. It is demonstrated that increasingly negative apparent depths are associated with increasing misfits between a 1D model and the data. Centroid depth calculations, which are a transform of the Fraser half-space parameters, provide an example of the detection of non-1D influences on data obtained above a populated area. 1D inversion of both theoretical and survey data is examined. The simplest use of the 1D inversion method is in providing an estimate of a half-space resistivity. This can be undertaken prior to multilayer inversion as an initial assessment. Underestimated altitude measurements also enter the problem and, in keeping with the Fraser pseudo-layer concept, an at-surface highly resistive layer of variable thickness can be usefully introduced as a constrained parameter. It is clearly difficult to ascribe levels of significance to a ‘measure’ of misfit contained in a negative apparent depth with the dimensions of metres. The reliability of 1D models is better assessed using a formal misfit parameter. With the misfit parameter in place, the example data suggest that the 1D inversion methods provide reliable apparent resistivity values with a higher resolution than the equivalent information from the Fraser half-space estimates. 相似文献
13.
D. PATELLA 《Geophysical Prospecting》1980,28(6):956-960
In this paper a theorem is demonstrated which allows—after the introduction of a suitable dipole kernel function or dipole resistivity transform function—to write the apparent resistivity function as an Hankel transformable integral expression. As a practical application of the theorem a procedure of quantitative interpretation of dipole soundings is suggested in which the dipole resistivity transform function obtained after inversion of the original dipole apparent resistivity data is used to control the goodness of the set of layering parameters which have been derived with our previous method of transformation of dipole sounding curves into equivalent Schlumberger diagrams. 相似文献
14.
Trans‐dimensional Bayesian inversion of controlled‐source electromagnetic data in the German North Sea 下载免费PDF全文
下载免费PDF全文 Romina A. S. Gehrmann Jan Dettmer Katrin Schwalenberg Martin Engels Stan E. Dosso Asli Özmaral 《Geophysical Prospecting》2015,63(6):1314-1333
This paper presents the first controlled‐source electromagnetic survey carried out in the German North Sea with a recently developed seafloor‐towed electrical dipole–dipole system, i.e., HYDRA II. Controlled‐source electromagnetic data are measured, processed, and inverted in the time domain to estimate an electrical resistivity model of the sub‐seafloor. The controlled‐source electromagnetic survey targeted a shallow, phase‐reversed, seismic reflector, which potentially indicates free gas. To compare the resistivity model to reflection seismic data and draw a combined interpretation, we apply a trans‐dimensional Bayesian inversion that estimates model parameters and uncertainties, and samples probabilistically over the number of layers of the resistivity model. The controlled‐source electromagnetic data errors show time‐varying correlations, and we therefore apply a non‐Toeplitz data covariance matrix in the inversion that is estimated from residual analysis. The geological interpretation drawn from controlled‐source electromagnetic inversion results and borehole and reflection seismic data yield resistivities of ～1 Ωm at the seafloor, which are typical for fine‐grained marine deposits, whereas resistivities below ～20 mbsf increase to 2–4 Ωm and can be related to a transition from fine‐grained (Holocene age) to unsorted, coarse‐grained, and compacted glacial sediments (Pleistocene age). Interface depths from controlled‐source electromagnetic inversion generally match the seismic reflector related to the contrast between the different depositional environments. Resistivities decrease again at greater depths to ～1 Ωm with a minimum resistivity at ～300 mbsf where a seismic reflector (that marks a major flooding surface of late Miocene age) correlates with an increased gamma‐ray count, indicating an increased amount of fine‐grained sediments. We suggest that the grain size may have a major impact on the electrical resistivity of the sediment with lower resistivities for fine‐grained sediments. Concerning the phase‐reversed seismic reflector that was targeted by the survey, controlled‐source electromagnetic inversion results yield no indication for free gas below it as resistivities are generally elevated above the reflector. We suggest that the elevated resistivities are caused by an overall decrease in porosity in the glacial sediments and that the seismic reflector could be caused by an impedance contrast at a thin low‐velocity layer. Controlled‐source electromagnetic interface depths near the reflector are quite uncertain and variable. We conclude that the seismic interface cannot be resolved with the controlled‐source electromagnetic data, but the thickness of the corresponding resistive layer follows the trend of the reflector that is inclined towards the west. 相似文献
15.
为了克服时间域航空电磁数据单点反演结果中常见的电阻率或层厚度横向突变造成数据难以解释的问题,通过引入双向约束实现航空电磁拟三维空间约束反演.除考虑沿测线方向相邻测点之间的横向约束外,同时还考虑了垂直测线方向测点在空间上的相互约束.为此,首先设计拟三维模型中固定层厚和可变层厚两种空间约束反演方案,然后通过在目标函数中引入沿测线和垂直测线方向上的模型参数约束矩阵,并使用L-BFGS算法使目标函数最小化,获得最优拟三维模型空间反演解.基于理论模型和实测数据反演,对单点反演与两种空间约束反演方案的有效性进行比较,证明本文空间约束反演算法对于噪声的压制效果好,反演的界面连续光滑,同时内存需求和反演时间少,是一种快速有效的反演策略. 相似文献
16.
Three‐dimensional modelling of magnetotelluric data to image Sehqanat hydrocarbon reservoir in southwestern Iran 下载免费PDF全文
下载免费PDF全文 A detailed magnetotelluric survey was conducted in 2013 in the Sehqanat oil field, southwestern Iran to map the geoelectrical structures of the sedimentary Zagros zone, particularly the boundary between the Gachsaran Formation acting as cap rock and the Asmari Formation as the reservoir. According to the electrical well logs, a large resistivity contrast exists between the two formations. The Gachsaran Formation is formed by tens to hundreds of metres of evaporites and it is highly conductive (ca. 1 Ωm–10 Ωm), and the Asmari Formation consists of dense carbonates, which are considerably more resistive (more than 100 Ωm). Broadband magnetotelluric data were collected along five southwest–northeast directed parallel lines with more than 600 stations crossing the main geological trend. Although dimensionality and strike analysis of the magnetotelluric transfer functions showed that overall they satisfied local 2D conditions, there were also strong 3D conditions found in some of the sites. Therefore, in order to obtain a more reliable image of the resistivity distribution in the Sehqanat oil field, in addition to standard 2D inversion, we investigated to what extent 3D inversion of the data was feasible and what improvements in the resistivity image could be obtained. The 2D inversion models using the determinant average of the impedance tensor depict the main resistivity structures well, whereas the estimated 3D model shows significantly more details although problems were encountered in fitting the data with the latter. Both approaches resolved the Gachsaran–Asmari transition from high conductivity to moderate conductivity. The well‐known Sehqanat anticline could also be delineated throughout the 2D and 3D resistivity models as a resistive dome‐shaped body in the middle parts of the magnetotelluric profiles. 相似文献
17.
传统核磁共振地下含水量解释多采用基于均匀半空间或层状导电模型的一维反演,分层给出地下含水信息.然而,这些方法忽略了地下复杂电阻率分布信息对结果的影响,也不能很好地反映局部三维含水构造.本文从三维电介质中核磁共振响应的正演理论出发,提出首先利用瞬变电磁数据进行基于等效导电平面法的快速电阻率成像,然后将成像结果作为核磁共振三维反演的电性模型,进行联合解释.激发磁场的分布采用有限元法直接求解,通过引入伪δ源实现电流源的加载,并强加散度条件排除了三维磁场模拟中"弱解"的影响.针对核磁共振灵敏度矩阵的病态性和数据中存在的干扰信号,提出考虑罚项的非线性拟合目标函数,利用线性化方法进行核磁共振反演.模型数据表明该方法能较准确反映地下三维含水构造,实测算例进一步证明了方法的有效性.本研究将促使核磁共振方法在岩溶、裂隙水、孤立水体等复杂水文地质条件及隧道、矿井灾害水源探测等方面得到有效应用. 相似文献
18.
Joint inversion of Rayleigh‐wave dispersion data and vertical electric sounding data: synthetic tests on characteristic sub‐surface models 下载免费PDF全文
下载免费PDF全文 In the traditional inversion of the Rayleigh dispersion curve, layer thickness, which is the second most sensitive parameter of modelling the Rayleigh dispersion curve, is usually assumed as correct and is used as fixed a priori information. Because the knowledge of the layer thickness is typically not precise, the use of such a priori information may result in the traditional Rayleigh dispersion curve inversions getting trapped in some local minima and may show results that are far from the real solution. In this study, we try to avoid this issue by using a joint inversion of the Rayleigh dispersion curve data with vertical electric sounding data, where we use the common‐layer thickness to couple the two methods. The key idea of the proposed joint inversion scheme is to combine methods in one joint Jacobian matrix and to invert for layer S‐wave velocity, resistivity, and layer thickness as an additional parameter, in contrast with a traditional Rayleigh dispersion curve inversion. The proposed joint inversion approach is tested with noise‐free and Gaussian noise data on six characteristic, synthetic sub‐surface models: a model with a typical dispersion; a low‐velocity, half‐space model; a model with particularly stiff and soft layers, respectively; and a model reproduced from the stiff and soft layers for different layer‐resistivity propagation. In the joint inversion process, the non‐linear damped least squares method is used together with the singular value decomposition approach to find a proper damping value for each iteration. The proposed joint inversion scheme tests many damping values, and it chooses the one that best approximates the observed data in the current iteration. The quality of the joint inversion is checked with the relative distance measure. In addition, a sensitivity analysis is performed for the typical dispersive sub‐surface model to illustrate the benefits of the proposed joint scheme. The results of synthetic models revealed that the combination of the Rayleigh dispersion curve and vertical electric sounding methods in a joint scheme allows to provide reliable sub‐surface models even in complex and challenging situations and without using any a priori information. 相似文献
19.
David Lopes de Castro Nilo Costa Pedrosa Jr.Fernando Acácio Monteiro Santos 《Journal of Applied Geophysics》2011,75(3):431-443
A joint inversion of gravity and geoelectrical data has been performed along a 100 km long profile across the oil-bearing Potiguar rift basin in NE Brazil. The integrated approach is based on the connection between density and resistivity of a sedimentary sequence through the porosity. Seventy-one gravity stations and twenty-nine vertical electrical soundings were carried out across the central part of the Early Cretaceous basin in the Precambrian Borborema Province to apply the proposed joint inversion. Both the physical properties and geometry of the multilayer deep model were well constrained by a wide set of prior information obtained by surface mapping, geophysical logs and seismic sections. The results reveal a rift architecture formed by a 5000 m thick half-graben structure separated by an intervening basement high and an extensive adjacent platform with a sedimentary infill of about 300 m thick. The calculated model shows geometries for the sedimentary density/resistivity interfaces in agreement with the seismostratigraphic sequences revealed by seismic section, representing a substantial improvement in comparison with previously published gravity models. 相似文献
20.
井地电阻率成像法利用井套管作电流源向井下供入大功率直流电流,在地表测量由地下介质的电性变化形成的电位分布,通过反演可得到地下介质的电阻率分布.针对大斜度井和水平井开展井地三维电阻率数值模拟和反演研究,对油田注水及压裂效果监测具有重要意义.基于井地电阻率成像法原理,采用有限差分法和不完全切勒斯基共轭梯度法进行了三维正演模拟,研究了大斜度井和水平井的井地电位响应特征.提出了采用层状约束阻尼最小二乘法由浅到深地进行大斜度井和水平井的多层联合反演,并对实际水平井井地电位各个层段数据进行了三维反演.模拟结果表明,倾斜线源和水平线源会对地面电位响应产生明显影响,在反演中需要考虑线源形态.实际水平井井地电位反演成像表明,考虑倾斜线源或者水平线源的联合反演得到了准确的水平井三维注水层成像图,得出注水层的真电阻率分布,能够判断注水运移方向. 相似文献