首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献，搜索用时 15 毫秒
1.
Summary. A geothermal and hydrochemical anomaly was observed in the Lower Triassic sandstone aquifer in the Vittel region (Vosges, France). This anomaly was attributed to a hydrothermal spring under sedimentary cover. In order to localize the hot spring and to quantify more precisely its flow rate and temperature, it is necessary to consider the 3-D thermal problem by taking into account the complex geometry of the domain and the flow rate in the aquifer. A 3-D numerical model of thermal conductive and forced convective transfer, developed for hydrological problems including approximate geometrical and topographical effects, is used which (i) can be directly applied to geologic strata (aquifers) with varying thickness and top and base slope; and (ii) allows calculation of heat flux anomalies associated with fluid flow in such geologically realistic aquifers.
The heat transfer equation is formulated in an orthogonal curvilinear coordinate system. As most geometries dealing with geothermal phenomena in sedimentary basins are nearly horizontal, this formulation can be simplified, leading readily to numerical solution with a finite difference method. The application of the 3-D model to the Vittel aquifer gives temperature results in agreement with measurements. These results provide evidence for the importance of associated forced convection and topographical effects for ground temperature distribution, and show clearly that heat flow in many basins is interpretable only if careful hydrological and thermal studies are made.  相似文献   

2.
In this research, a simulation was performed for evaluating power production from an abandoned geothermal well as an enhanced geothermal system by injecting a secondary fluid. Abandoned wells, due to lack of fluid or very low transmissivity, are regarded among the low-to moderate-temperature resources that have the potential for heat production without any cost for deep drilling. Accordingly, they are taken as suitable sources of energy. In the present paper, an abandoned geothermal well at Meshkinshahr geothermal field in Sabalan district, northwestern Iran, with 3176 m depth was simulated. The bottom-hole temperature of 148 °C, as well as well casing size, and real thermal gradient for well were applied in the model. A 3D heat transfer simulation model was designed by considering a coaxial pipe as a down-hole heat exchanger between surrounding rocks of the well and injected fluid. Injected fluid to the well with specified pressure and temperature receives heat from rocks surrounding the well, until it reaches the bottom of the well and converts to vapor. The vapor returns to the surface from inner pipe with very low heat loss during its return. The inner pipe is isolated by a thin layer having a low heat conductivity to prevent heat loss from the returned fluid. It was observed that obtained heat in the well depends on temperature profile of the well, injection velocity, and fluid mass flow rate. The model results were optimized by selecting suitable parameters such as inlet injection speed and fluid flow rate to achieve the highest temperature of the fluid returned from the well. A binary power plant was also modeled to determine the extractable power using returned fluid as input using ammonia and isobutene, as working fluids in binary cycle. Finally, electric power of 270 kW was generated from well NWS3 using designed down-hole heat exchanger.  相似文献   

3.
J.A. Nunn  G. Lin 《Basin Research》2002,14(2):129-145
ABSTRACT Sedimentary rocks rich in organic matter, such as coal and carbonaceous shales, are characterized by remarkably low thermal conductivities in the range of 0.2–1.0 W m?1 °C?1, lower by a factor of 2 or more than other common rock types. As a result of this natural insulating effect, temperature gradients in organic rich, fine‐grained sediments may become elevated even with a typical continental basal heat flow of 60 mW m?2. Underlying rocks will attain higher temperatures and higher thermal maturities than would otherwise occur. A two‐dimensional finite element model of fluid flow and heat transport has been used to study the insulating effect of low thermal conductivity carbonaceous sediments in an uplifted foreland basin. Topography‐driven recharge is assumed to be the major driving force for regional groundwater flow. Our model section cuts through the Arkoma Basin to Ozark Plateau and terminates near the Missouri River, west of St. Louis. Fluid inclusions, organic maturation, and fission track evidence show that large areas of upper Cambrian rocks in southern Missouri have experienced high temperatures (100–140 °C) at shallow depths (< 1.5 km). Low thermal conductivity sediments, such as coal and organic rich mudstone were deposited over the Arkoma Basin and Ozark Plateau, as well as most of the mid‐continent of North America, during the Late Palaeozoic. Much of these Late Palaeozoic sediments were subsequently removed by erosion. Our model results are consistent with high temperatures (100–130 °C) in the groundwater discharge region at shallow depths (< 1.5 km) even with a typical continental basal heat flow of 60 mW m?2. Higher heat energy retention in basin sediments and underlying basement rocks prior to basin‐scale fluid flow and higher rates of advective heat transport along basal aquifers owing to lower fluid viscosity (more efficient heat transport) contribute to higher temperatures in the discharge region. Thermal insulation by organic rich sediments which traps heat transported by upward fluid advection is the dominant mechanism for elevated temperatures in the discharge region. This suggests localized formation of ore deposits within a basin‐scale fluid flow system may be caused by the juxtaposition of upward fluid discharge with overlying areas of insulating organic rich sediments. The additional temperature increment contributed to underlying rocks by this insulating effect may help to explain anomalous thermal maturity of the Arkoma Basin and Ozark Plateau, reducing the need to call upon excessive burial or high basal heat flow (80–100 mW m?2) in the past. After subsequent uplift and erosion remove the insulating carbonaceous layer, the model slowly returns to a normal geothermal gradient of about 30 °C km?1.  相似文献   

4.
Basin and petroleum systems are routinely modelled to provide qualitative and quantitative assessments of a hydrocarbon play. The importance of the rock thermal properties and heat flow density in thermal modelling the history of a basin are well-known, but little attention is paid to assumptions of the thermal conductivity, present-day heat flow density and thermal history of basins. Assumed values are often far from measured values when data are available to check parameters, and effective thermal conductivity models prescribed in many basin simulators require improvement. The reconstructed thermal history is often justified by a successful calibration to present-day temperature and vitrinite reflectance data. However, a successful calibration does not guarantee that the reconstruction history is correct. In this paper, we describe the pitfalls in setting the thermal conductivity and heat flow density in basin models and the typical uncertainties in these parameters, and we estimate the consequences by means of a one-dimensional model of the super-deep Tyumen SG-6 well area that benefits from large amounts of reliable input and calibration data. The results show that the entire approach to present-day heat flow evaluations needs to be reassessed. Unreliable heat flow density data along with a lack of measurements of rock thermal properties of cores can undermine the quality of basin and petroleum system modelling.  相似文献   

5.
We investigate the effects of convective heat transfer on the thermal history of sediments and petroleum formation within continental rift basins using one-dimensional mathematical modelling. The transport equations used in this study to describe vertical groundwater flow and conductive/convective heat transfer are solved by the finite element method. Sediment thermal history is quantitatively represented using first-order rate kinetic expressions for kerogen degradation and an empirical fanning Arrhenius model for apatite fission track annealing. Petroleum generation is also represented in the model by a suite of first-order rate kinetic expressions. The analysis provides insights into how pore fluid circulation patterns are preserved in the rock record as anomalies in palaeogeothermometric data within continental rifts. Parameters varied in the numerical experiments include the ratio of conductive to convective heat transfer (thermal Peclet number; Pe) and the composition of the disseminated organic matter in the sediment (type II and III kerogen). Quantitative results indicate that vertical groundwater flow rates on the order of a mm/yr cause a change in computed vitrinite reflectance of the rocks and a shift in the depth to oil generation by as much as 3000 m. Differences in thermal gradients between recharge and discharge areas (Pe= 0.6) also change the width of the zone of oil generation by a factor of two. Even more dramatic, however, are the large changes in predicted apatite fission track length distributions and model ages between recharge and discharge areas. For example, a sediment package buried to a depth of 2400 m over 200 Myr within the groundwater recharge column had a fission track length distribution with a computed mean and standard deviation of 12.83 μm and 0.77 μm, respectively. The fission track model age for this sediment package was 209 Ma. The same sediment package in the discharge area has a distribution with a mean track length of 5.68 μm, a standard deviation of 3.37 μm, and a fission track model age of 2.6 Ma. Transient groundwater flow simulations, in which fluid circulation ceases after a period of time within the rift basin, are also presented to illustrate how disturbances in palaeogeothermometric parameters are preserved on geological time-scales. Vitrinite reflectance profiles require about 10 Myr to return to conductive conditions within groundwater recharge areas while the convective disturbances are preserved indefinitely along the discharge column, as long as further subsidence does not occur. Ancient groundwater flow systems are preserved as anomalies in computed apatite fission track model ages and distributions much longer after groundwater flow stops, relative to organic-based geothermometers. Significant differences exist in model ages between recharge (145 Ma) and discharge (90 Ma) areas 200 Myr after flow has ceased. However, calculated fission track histogram distributions are virtually identical in recharge and discharge areas after about 50 Myr. Our study suggests that ancient groundwater flow systems can be detected by comparing thermochronometric data between suspected recharge and discharge areas within continental rifts. Vitrinite reflectance profiles, observed offsets in the depth to the onset of petroleum generation, and apatite fission track annealing studies are all well suited for detecting groundwater flow systems which have been relatively long lived (107 years). Apatite fission track age data are probably best suited for identifying ancient groundwater flow systems within rifts long (>200 Myr) after flow ceases.  相似文献   

6.
Summary. We demonstrate a method of performing linear programming optimizations of functionals of subsurface temperature, when thermal conductivity is a known piecewise-constant function. Data comprise heat flow measurements on the flat isothermal surface of this structure, within which heat transfer is by steady-state conduction. Two-dimensionality is assumed. The approach involves establishing constraints which demand the continuity of temperature and the normal component of heat flow across all internal boundaries. These unknown functions are expanded as truncated Fourier series whose coefficients become unknowns of the linear programming solution vector; linear relations are established between these coefficients which guarantee harmonicity of temperature in each region of uniform conductivity, as well as the continuity requirements. Variations of the formalism are detailed for three simple types of geometry. As an example the method is applied to a heat flow data set from Sass, Killeen & Mustonen over the Quirke Lake Syncline of Ontario, Canada.  相似文献   

7.
Defining temperature at depth to identify geothermal resources relies on the evaluation of the Earth heat flow based on equilibrium temperature measurements as well as thermal conductivity and heat generation rate assessment. Such high-quality geothermal data can be sparse over the region of interest. This is the case of the St. Lawrence Lowlands sedimentary basin covering 20,000 km2 to the south of Québec, Canada, and enclosing only three wells up to a depth of 500 m with equilibrium heat flow measurements. However, more than 250 oil and gas exploration wells have been drilled in this area, providing for this study (parce que c'est 93 sinon) 81 locations with bottom-hole temperature up to a depth of 4300 m, however, not at equilibrium. Analyzing these data with respect to the deep geothermal resource potential of this sedimentary basin requires evaluating the thermal conductivity and heat generation rate of its geological units to properly extrapolate temperature downward. This was done by compiling literature and recent thermal conductivity measurements in outcrop and core samples as well as new heat generation rate estimates from spectral gamma ray logs to establish a first thermal assessment of geological units deep down into the basin. The mean thermal conductivity of the thermal units varies from 2.5 to 6.3 W/m·K, with peak values in the basal sandstones, while the heat generation rate varies from 1.6 to 0.3 µW/m3, decreasing from the upper caprocks toward the base of the sequence. After correcting the bottom-hole temperatures for drilling disturbance with the Harrison correction and subsequently for paleoclimate variations, results indicate a mean geothermal gradient of 23.1 °C/km, varying from 14 to 40 °C/km. Evaluating the basin thermal state from oil and gas data is a significant challenge facilitated by an understanding of its thermal properties.  相似文献   

8.
Open fractures provide high-permeability pathways for fluid flow in sedimentary basins. The potential for flow along permeable or open fractures and faults depends on the continuity of flow all the way to the surface except in the case of convective flow. Upward flowing fluid cools and may cause cementation due to the prograde solubility of quartz, but in the case of carbonates such flow may cause dissolution. The rate and duration of these processes depend on the mechanisms for sustaining fluid flow into the fracture, the geometries of fracture and sedimentary beds intersected, permeability, pressure and temperature gradients. Heat loss to the adjacent sediments causes sloping isotherms which can induce non-Rayleigh convection. To analyse these problems we have used a simple model in which a single fracture acts as a pathway for vertically moving fluid and there is no fluid transport across the walls of the fracture except near its inlet and outlet. Four mechanisms for fluid flow into the lower part of the fracture are considered: decompression of pore water; compaction of intersected overpressared sediments; focusing of compaction water derived from sediments beneath the fracture; and finally focusing of pore water moving through an aquifer. Water derived from the basement is not considered here. We find that sustained flow is unlikely to have velocities much higher than 1–100 m/yr, and the flow is laminar. The temperature of the fluid expelled at the top of the fracture increases by less than 1% and the vertical temperature gradient in the fracture remains close to the geothermal gradient. Where hot water is introduced from basement fractures (hydrothermal water) during tectonic deformation, much higher velocities may be sustained in the overlying sediments, but here also this depends on the permeability near the surface. Most of the cooling of water with (ore) mineral precipitation will then occur near the surface. In most cases, pore water decompression and sediment compaction will yield only very limited pore water flux with no significant potential for cementation or heating of the sediments adjacent to the fracture. Focusing of compaction water from sediments beneath the fracture or from an intersected aquifer can yield fluxes high enough to cement an open fracture significantly but the flow must be sustained for a very long time. For velocities of 1–100 m/yr, it takes typically 0.3–30 Myr to cement a fracture by 50%. The highest velocities may be obtained when a fracture extends all the way to the surface or sea floor. When a fracture does not reach the sediment surface, the flow velocity is reduced by the displacement of water in the sediments near the top of the fracture. The flow into the fracture from the sediments may often be rate limiting rather than the flow on the fracture. Sedimentary rocks only a few metres from the fracture will receive a much lower flux than the fracture. The fracture will therefore close due to cementation before significant amounts of silica can be introduced into adjacent sandstones. The isotherm slope in the adjacent sediments will in most cases be less than 10–20°. Non-Rayleigh convection velocities in the sediments adjacent to the fracture are too small to cause any significant diagenetic reactions such as quartz cementation. These quantifications of fluid flow in fractures in sedimentary basins are important in terms of constraining models for diagenesis, heat transport and formation of ore minerals in a compaction-driven system.  相似文献   

9.
The Chagan Depression in the Yingen-Ejinaqi Basin, located at the intersection of the Paleo-Asian Ocean and the Tethys Ocean domains is an important region to gain insights on terrestrial heat flow, lithospheric thermal structure and deep geodynamic processes. Here, we compute terrestrial heat flow values in the Chagan Depression using a large set of system steady-state temperature data from four representative wells and rock thermal conductivity. We also estimate the “thermal” lithospheric thickness, mantle heat flow, ratio of mantle heat flow to surface heat flow and Moho temperature to evaluate the regional tectonic framework and deep dynamics. The results show that the heat flow in the Chagan Depression ranges from 66.5 to 69.8 mW/m2, with an average value of 68.3 ± 1.2 mW/m2. The Chagan Depression is characterized by a thin “thermal” lithosphere, high mantle heat flow, and high Moho temperature, corresponding to the lithospheric thermal structure of “cold mantle and hot crust” type. We correlate the formation of the Yingen-Ejinaqi Basin to the Early Cretaceous and Cenozoic subduction of the western Pacific Plate and the Cenozoic multiple extrusions. Our results provide new insights into the thermal structure and dynamics of the lithospheric evolution in central China.  相似文献   

10.
A model of time-periodic mantle flow   总被引：1，自引：0，他引：1  
Summary. The instability of a layer consisting of a lighter viscous fluid on top of a heavier less viscous fluid is considered in the case when the heavy fluid is adiabatically stratified and the light fluid contains heat sources and possesses a lower heat conductivity. A perturbation in the thickness of the upper fluid layer causes horizontal temperature variations in the lower fluid. The motions induced by thermal buoyancy can interact with the distortion of the interface in such a way that the initial perturbation is reinforced in the form of an overstable oscillation. It is proposed that this mechanism is relevant to the problem of time-dependent flow in the Earth's mantle.  相似文献   

11.
To decipher the thermal structure of the sedimentary veneer in southern Israel, new values of thermal conductivity and porosity as well as of the radiogenic heat budget are provided. Thermal conductivity is measured for lithotypes and scaled up for geological formations. The new data are higher than most of the previously measured values, in particular for sandstones and siltstones, whose mean values are 5.0 and 2.9 W m?1 K?1. Mean values of the most abundant lithotypes, which are dolomites and limestones, are on the order of 4.1 and 2.7 W m?1 K?1, respectively. The total radiogenic heat production of the sedimentary cover varies slightly over southern Israel, due to variable lithology and total sediment thickness, yielding a maximum heat flow on the order of 4 mW m?2 where the sedimentary section is thickest (ca. 7 km). A temperature prognosis was made by calculating temperature profiles to the top of the crystalline basement at five well locations applying the new thermal‐conductivity data set and three scenarios of surface heat flow (50, 55 and 60 mW m?2). The calculated temperatures best match with measured drillstem‐test temperatures by using heat‐flow values close to the upper bound of range. Surface heat flow on the order of 55–60 mW m?2 is supported by a reevaluation of an existing temperature log and the application of thermal conductivity from this study. The temperature prediction for southern Israel shows values of 100–120°C at 3500–4500 m depth, indicating a geothermal potential that can be used for heating as well as electricity production.  相似文献   

12.
The North Slope foreland basin, Alaska, USA is an east–west asymmetrical trough‐shaped basin adjacent to the Brooks Range fold‐thrust mountain belt. Lower Cretaceous age rocks make up much of the sediment fill, including flysch‐like marine turbidites and shales of the Torok and Fortress Mountain formations and marine and sandstones, shales and conglomerates of the overlying Nanushuk group. Lower Cretaceous age rocks were deposited on top of a Palaeozoic and Mesozoic age passive margin sequence. We have conducted numerical simulations of fluid flow driven by topographic recharge in the Central North Slope foreland basin. These simulations are constrained by salinity estimates from well logs, location of oil and gas fields, vitrinite reflectance and heat flow measurements. Our model results indicate that there are two south to north pathways for fluid migration. The primary pathway for fluid movement is downward through the Fortress Mountain formation, then upwards along the interface between the Fortress Mountain and Torok Formation and finally northward through the permeable Nanushuk group. A smaller mass of groundwater moves along sands below the Torok formation and into offshore sediments north of Alaska. Very little meteoric water enters the underlying Palaeozoic rocks in our simulations, which could explain the presence of deep saline pore waters. Our results also show that permafrost is a primary control on the pathway and rate of fluid flow by controlling the distribution of surface recharge and discharge. For example, areas of high heat flow and low saline waters along the arctic coast may represent upward groundwater discharge because of the absence of permafrost. As surface temperatures were warmer in the Miocene, the absence of permafrost would produce a more local fluid circulation pattern and less transfer of heat energy from south to north.  相似文献   

13.
Significant lateral variations in observed temperatures in the Beaufort‐Mackenzie Basin raise the question on the temperature‐controlling factors. Based on the structural configuration of the sediments and underlying crust in the area, we calculate the steady‐state 3D conductive thermal field. Integrated data include the base of the relic permafrost layer representing the 0 °C‐isotherm, public‐domain temperature data (from 227 wells) and thermal conductivity data. For >75% of the wells the predicted temperatures deviate by <10 K from the observed temperatures, which validates the overall model setup and adopted thermal properties. One important trend reproduced by the model is a decrease in temperatures from the western to the eastern basin. While in the west, a maximum temperature of 185 °C is reached at 5000 m below sea level, in the east the maximum temperature is 138 °C. The main cause for this pattern lies in lateral variations in thermal conductivity indicating differences in the shale and sand contents of the different juxtaposed sedimentary units. North‐to‐south temperature trends reveal the superposition of deep and shallow effects. At the southern margin, where the insulating effect of the low‐conductive sediments is missing, temperatures are lowest. Farther north, where the sub‐sedimentary continental crust is thick enough to produce considerable heat and a thick pile of sediments efficiently stores heat, temperatures tend to be highest. Temperatures decrease again towards the northernmost distal parts of the basin, where thinned continental and oceanic crust produce less radiogenic heat. Wells with larger deviations of the purely conductive model from the temperature observations (>15 K at 10% of the wells) and their basin‐wide pattern of misfit tendency (too cold vs. too warm temperature predictions) point to a locally restricted coupling of heat transport to groundwater flow.  相似文献   

14.
1985—1986年度和1986—1987年度在菲尔德斯半岛对地面温度进行了测量,共获得129个数据,并对带回的样品进行了岩石热导率测量,共获得210个数据。本文在分析和归纳这些数据的基础上对菲尔德斯半岛的地温特征和岩石热物理性质进行了初步探讨。  相似文献   

15.
基于盐湖资源的硝酸熔盐储能材料性能研究   总被引：1，自引：1，他引：0  
太阳能光热发电是可再生能源发展的主要方向。作为太阳能光热发电的核心技术,熔融盐以热容量大、粘度低、蒸汽压低、使用温度范围宽等诸多独特的性能优势,成为光热发电储能的首选。相比之下,硝酸熔盐具有优良的传热和流体流动等特性,使其在光热储热系统中的性能优势较为突出。我国盐湖地区具备太阳能光热发电的发展空间和优势,丰富的无机盐资源可以降低相关相变储能材料的生产成本,有利于推进太阳能的规模化发展、能源结构的调整优化。据此,立足于盐湖资源的开发利用,以硝酸盐系列传热蓄热介质的工业应用为背景,针对产业化的二元硝酸盐熔盐做了更深入的系统研究;在此基础上,通过添加硝酸镁,制备了低熔点的三元熔盐储能材料;并将碳纳米管引入到硝酸盐体系,进一步提升了其导热性能。这不仅为硝酸熔盐储热材料的制备提供了理论基础,也为其在光热发电的应用打开了更多的可能性。  相似文献   

16.
《极地研究》1991,2(2):38-46
Based on detailed measurements of density and a numerous data on temperature in shallow bore holes (about 20m deep), the thermal properties and temperature distribution of snow/firn layer on the Law Dome ice cap, Antarctica, are discussed. According to a review of works on thermal properties of snow by Yen (1981), a relationship between thermal conductivity (K) and density (~) is proposed to be expressed by a formula, K=0.0784+2.697_(ρ~2). Then an eqation of heat transfer in a deformed ununiform medium is applied and solved analytically by two approaches. Comparison of calculated and measured temperatures indicates that the difference is mainly dependent on the determination of boundary donditions.  相似文献   

17.
A methodology for calculating the thermal conductivity of soils and rocks is developed which takes into account their origin and mineralogical composition.This method utilizes three approaches.One is founded on the structural modeling of contact heat interaction between particles and fills and estimates the statistical probability distribution of the particles in the volume of the medium.The second approach analyses perturbation to the temperature field of the matrix medium by ellipsoidal inclusions.The third approach is to find the mean thermal conductivity of the solid skeleton in the universal model at different composition of rock-forming minerals.  相似文献   

18.
The Cameros Basin (North Spain) is a Late Jurassic‐Early Cretaceous extensional basin, which was inverted during the Cenozoic. It underwent a remarkable thermal evolution, as indicated by the record of anomalous high temperatures in its deposits. In this study, the subsidence and thermal history of the basin is reconstructed, using subsidence analysis and 2D thermal modelling. Tectonic subsidence curves provide evidence of the occurrence of two rapid subsidence phases during the syn‐extensional stage. In the first phase (Tithonian‐Early Berriasian), the largest accommodation space was formed in the central sector of the basin, whereas in the second (Early Barremian‐Early Albian), it was formed in the northern sector. These rapid subsidence phases could correspond to relevant tectonic events affecting the Iberian Plate at that time. By distinguishing between the initial and thermal subsidence and defining their relative magnitudes, Royden's (1986) method was used to estimate the heat flow at the end of the extensional stage. A maximum heat flow of 60–65 mW/m2 is estimated, implying only a minor thermal disturbance associated with extension. In contrast with these data, very high vitrinite reflectance, anomalously distributed in some case with respect to the typical depth‐vitrinite reflectance relation, was measured in the central‐northern sector of the basin. Burial and thermal data are used to construct a 2D thermal basin model, to elucidate the role of the processes involved in sediment heating. Calibration of the thermal model with the vitrinite reflectance (%Ro) and fluid inclusion (FI) data indicates that in the central and northern sectors of the basin, an extra heat source, other than a typical rift, is required to explain the observed thermal anomalies. The distribution of the %Ro and FI values in these sectors suggests that the high temperatures and their distribution are related to the circulation of hot fluids. Hot fluids were attributed to the hydrothermal metamorphic events affecting the area during the early post‐extensional and inversion stages of the basin.  相似文献   

19.
The blanketing effect in sedimentary basins   总被引：3，自引：0，他引：3  
  相似文献   

20.
Sedimentary rocks such as coal and carbonaceous mudstone which contain abundant carbonaceous matter are characterized by thermal conductivity much lower than that exhibited by other common rock types, by a factor of 5–10. As a result, temperature gradients in such sediments can range up to 0.25 °Cm-1 even under conditions of average heat flow. When such steep gradients extend over a significant sedimentary thickness, temperatures of underlying rock units are elevated, causing both organic and inorganic phases to record what seem to be anomalously high levels of thermal maturity. This carbonaceous blanket insulating effect may help to explain unusual levels of maturity observed at shallow depths in the Appalachian Basin, Michigan Basin and other regions of the world with significant carbonaceous strata.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号