共查询到20条相似文献，搜索用时 31 毫秒
1.
颗粒破碎对颗粒材料宏观力学行为有重要影响。 结合Hardin的破碎经验公式,将表征破碎程度的破碎参量与Cosserat连续体的内部长度参数相关联,形成一个基于Cosserat连续体且能考虑颗粒破碎的弹塑性模型。数值算例主要考察了颗粒破碎对颗粒材料承载能力、塑性应变及局部化行为的影响,数值结果表明,颗粒破碎主要发生在剪切带内,颗粒破碎使得剪切带明显变窄且剪切带内外等效塑性应变梯度明显增大。 相似文献
2.
颗粒破碎是影响砂土宏-微观力学性质的重要因素。采用改进型的可破碎颗粒生成方法,通过设置不同强度的平行黏结键模拟不同强度的可破碎颗粒,并借用基于离散元方法（DEM）的双轴压缩试验详细研究了可破碎性土在剪切过程中颗粒破碎率/平均破碎程度、微观尺度上的能量耗散分配机制、剪切破碎带形成以及断裂键各向异性的演化过程。结果表明,颗粒破碎强烈地影响砂土在宏观尺度上的力学响应、颗粒尺度上的能量分配机制以及剪切过程中的颗粒的组织结构演化。颗粒破碎主要影响小应变阶段各能量耗散元的分配机制,而在临界状态下剪切带内的颗粒摩擦以及破碎耗能是消耗外界功的主要因素。数值结果亦表明,颗粒的破碎伴随着整个剪切过程,但破碎率的增长速度却随着剪切应变的发展逐渐降低。另外,在剪切过程中,对于低破碎性土,在临界状态下剪切破碎带基本形成,带内的原有组织结构被打乱,断裂键的各向异性也随之弱化。 相似文献
3.
The mechanical property of frozen saline sandy soil is complicated due to its complex components and sensitivity to salt content and confining pressure. Thus, a series of triaxial compression tests were carried out on sandy samples with different Na2SO4 contents under different confining pressures to explore the effects of particle breakage, pressure melting, shear dilation and strain softening or hardening. The test results indicate that the stress–strain curves exhibit strain softening/hardening phenomena when the confining pressures are below or above 6 MPa, respectively. A shear dilation phenomenon was observed in the loading process. With increasing confining pressure, the strength firstly increases and then decreases. By taking into consideration the changes between the grain size distributions before and after triaxial compression tests, a failure strength line incorporating the influences of both particle breakage and pressure melting is proposed. In order to describe the deformation characteristics of frozen saline sandy soil, an elastoplastic incremental constitutive model is established based on the test results. The proposed model considers the plastic compressive, plastic shear and breakage mechanisms by adopting the non-associated flow rule. The breakage mechanism can be reflected by an index related to the initial, current and ultimate grain size distributions. The hardening parameters corresponding to compressive and shear mechanisms consider the influence of particle breakage. Then the effect of particle breakage on both the stress–strain and volumetric strain curves is analyzed. The calculated results fit well with the test results, indicating that the developed constitutive model can well describe the mechanical and deformation features of frozen saline sandy soil under various stress levels and stress paths. In addition, the strain softening/hardening, contraction, high dilation and particle breakage can be well captured. 相似文献
4.
在单轴平面应变压缩条件下, 采用FLAC模拟了剪切扩容对含随机缺陷岩石破坏前兆及变形特征的影响。密实的岩石服从莫尔库仑剪破坏与拉破坏复合的破坏准则, 破坏之后呈现应变软化-理想塑性行为。缺陷在破坏之后经历理想塑性行为。随着轴向应变的增加, 试样内部破坏的单元数目增加, 直到达到一个常数, 该常数随着扩容角的增加而增加。当扩容角较高时, 计算得到的泊松比在峰前就可以超过0.5;剪切扩容于峰前发生; 变形后试样的最终体积大于初始体积。剪切局部化(导致了毗邻块体之间的相对滑动)及剪切扩容(发生于剪切带内部)是非零扩容角试样峰后体积膨胀的原因。在峰前, 通过观察剪切应变增量、破坏的单元数目、侧向应变、计算得到的泊松比及体积应变可以发现, 扩容角越高, 试样破坏的前兆越明显。在低扩容角时, 由于弯曲的剪切带边界, 试样内部充分发展的剪切带的倾角比较分散, 剪切带的倾角更接近Arthur理论。 相似文献
5.
In granular soils grain crushing reduces dilatancy and stress obliquity enhances crushability. These are well-supported specimen-scale experimental observations. In principle, those observations should reflect some peculiar micromechanism associated with crushing, but which is it? To answer that question the nature of crushing-induced particle-scale interactions is here investigated using an efficient DEM model of crushable soil. Microstructural measures such as the mechanical coordination number and fabric are examined while performing systematic stress probing on the triaxial plane. Numerical techniques such as parallel and the newly introduced sequential probing enable clear separation of the micromechanical mechanisms associated with crushing. Particle crushing is shown to reduce fabric anisotropy during incremental loading and to slow fabric change during continuous shearing. On the other hand, increased fabric anisotropy does take more particles closer to breakage. Shear-enhanced breakage appears then to be a natural consequence of shear-enhanced fabric anisotropy. The particle crushing model employed here makes crushing dependent only on particle and contact properties, without any pre-established influence of particle connectivity. That influence does not emerge, and it is shown how particle connectivity, per se, is not a good indicator of crushing likelihood. 相似文献
6.
Acta Geotechnica - An elastic–plastic constitutive model considering particle breakage for simulation of crushable granular soils behavior is proposed. In the model, elastic strain rates are... 相似文献
7.
A new elastoplastic model is developed for rockfills within the general critical state framework incorporating the state parameter. Two state functions are proposed to characterize the evolution of volume dilation and strain softening of rockfills, and a modified breakage index based on the concept of Hardin's relative breakage is defined to describe the progressive crushing of rockfills. The nonassociated plastic flow rule is derived from a state dependent dilatancy equation, and it incorporates energy dissipation due to intrinsic nonlinear friction and particle breakage upon shearing. Thus, their couple effect on the plastic deviatoric and volumetric deformation of rockfills is taken into account in the current model. The numerical analyses are carried out for a series of drained triaxial tests on the modeled rockfills at various consolidation pressures and stress paths. The volume dilation/contraction and strain softening/hardening of rockfills are accurately predicted by the proposed model, and the particle breakage and nonlinear critical state shear strength of rockfills are also well captured. The research findings indicate that the current model is applicable to represent the complex stress–strain–volume change behavior of rockfills in general. Copyright © 2013 John Wiley & Sons, Ltd. 相似文献
8.
It is well known that the compressibility of crushable granular materials increases with the moisture content,due to the decrease of particle strength in a humid environment.An existing approach to take into account the effect of grain breakage in constitutive modeling consists in linking the evolution of the grain size distribution to the plastic work.But how the material humidity can affect this relationship is not clear,and experimental evidence is quite scarce.Based on compression tests on dry and saturated crushable sand recently reported by the present authors,a new non-linear relationship is proposed between the amount of particle breakage and the plastic work.The expression contains two parameters:(1)a material constant dependent on the grain characteristics and(2)a constant depending on the wetting condition(in this study,dry or saturated).A key finding is that the relationship does not depend on the stress path and,for a given wetting condition,only one set of parameters is necessary to reproduce the results of isotropic,oedometric,and triaxial compression tests.The relationship has been introduced into an elastoplastic constitutive model based on the critical state concept with a double yield surface for plastic sliding and compression.The breakage ratio is introduced into the expression of the elastic stiffness,the critical state line and the hardening compression pressure.Incremental stress-strain computations with the model allow the plastic work to be calculated and,therefore,the evolution of particle crushing can be predicted through the proposed non-linear relationship and reintroduced into the constitutive equations.Accurate predictions of the experimental results in terms of both stress-strain relationships and breakage ratio were obtained. 相似文献
9.
粗粒土的颗粒破碎直接改变了土体本身结构,对粗粒土的剪胀和内摩擦角都会产生影响。在土体剪切过程中,体积应力和剪切应力在体积应变和剪切应变上做功,这部分能量在剪切过程中转化为颗粒的弹性储能、颗粒间的摩擦耗能、颗粒剪胀时对外做功和颗粒破碎耗能4部分。准确计算剪切过程中粗粒土破碎耗能的目的是：从能量角度分析颗粒破碎对土体本构关系的影响,为建立考虑颗粒破碎的粗粒土本构关系创造条件。通过分析粗粒土的常规三轴试验数据,计算得到了剪切过程中的粗粒土破碎耗能。计算结果表明,常规三轴试验条件下粗粒土破碎耗能主要受固结应力、土体摩擦系数M等因素的影响。 相似文献
10.
This study investigates the influence of the intermediate principle stress on the particle breakage of granular materials. The crushable agglomerate method is applied to model soil particles and numerical true triaxial tests were carried out. The results show that particle breakage increases with increasing b value, the relationship of which follows an exponential function and agrees well with previous experimental results. More importantly, the study found that the relationship between particle breakage and total energy input is independent of the intermediate principle stress, which provides a good basis for the constitutive modeling of granular materials. 相似文献
11.
A series of laboratory tests were performed to examine the fatigue behavior of granite subjected to cyclic loading under triaxial compression condition. In these tests, the influences of volumetric change and residual strain on the deformation modulus of granite under triaxial cyclic compression were investigated. It is shown that the fatigue behavior of granite varies with the tendency for volumetric change in triaxial cyclic compression tests. In the stress–strain space, there are three domains for fatigue behavior of rock subjected to cyclic loading, namely the volumetric compaction, volumetric dilation with strain-hardening behavior, and volumetric dilation with strain-softening behavior domains. In the different domains, the microscopic mechanisms for rock deformation are different. It was also found that the stress level corresponding to the transition from volumetric compaction to volumetric dilation could be considered as the threshold for fatigue failure. The potential of fatigue deformation was compared with that of plastic deformation. The comparison shows that rocks exhibit higher resistances to volumetric deformation under cyclic loading than under plastic loading. The influence of residual strain on the fatigue behavior of rock was also investigated. It was found that the axial residual strain could be a better option to describe the fatigue behavior of rock than the loading cycle number. A constitutive model for the fatigue behavior of rock subjected to cyclic loading is proposed according to the test results and discussion. In the model, the axial residual strain is considered as an internal state variable. The influences of confining pressure and peak deviatoric stress on the deformation modulus are considered in a term named the equivalent stress. Comparison of test results with model predictions shows that the proposed model is capable of describing the prepeak fatigue behavior of rock subjected to cyclic loading. 相似文献
12.
Crushability is one of the important behaviors of granular materials particularly under high stress states, and affects both the deformability and strength of the materials that are in essence associated with state‐dependent dilatancy. In this presentation, first, a new critical state model is proposed to take into account the three different modes of compressive deformation of crushable granular materials, i.e. particle rearrangement, particle crushing and pseudo‐elastic deformation. Second, the governing equations for cavity expansion in crushable granulates are introduced, in which the state‐dependent dilatancy as well as the bounding surface plasticity model are used. Then, the procedure to obtain semi‐analytical solutions to cavity expansion in the material is described in detail, in which a commercial differential equation solver is employed. Finally, cavity expansion analyses are carried out on Toyoura sand, a well‐documented granular material, to demonstrate the effects of crushability and state‐dependent dilatancy. The study shows that particle crushing does occur at both high stress and critical states and affects the stress fields and the deformation behavior of the material surrounding the cavity in association with state‐dependent dilatancy. This leads to conclusion that particle crushing and state‐dependent dilatancy have to be taken into account when cavity expansion theory is used to interpret cone penetration tests and pressuremeter tests. Copyright © 2011 John Wiley & Sons, Ltd. 相似文献
13.
The particle breakage of granular materials under compression is a phenomenon of great importance. In this paper, a micromechanically based model for the compression of crushable granular materials is developed in the framework of thermomechanics. Both the internal and dissipative energies in the model are derived using the micro–macro volume averaging approach to ensure that all parameters involved have concrete physical meanings. The particle breakage is quantified by the change of the maximum particle size, the size polydispersity and the fractal dimension of the gradation. Compared to other breakage models, there is a major difference that highlights the novelty of the proposed model: neither the ultimate particle size distribution, nor the evolution path of the gradation is predefined in the model. The initiation, evolution and the attenuation of the breakage can be determined by the maximum dissipation principle using thermomechanics and micromechanics. Finally, it is demonstrated that the proposed model can predict the stress dependence of the elastic bulk modulus, the size dependence of the yielding stress and the elastic–plastic-pseudoelastic phase transition of granular materials. 相似文献
14.
粗粒土在较大的应力条件下容易产生颗粒破碎现象,而现有的大多数模型都没有考虑剪切过程中的颗粒破碎。模型将塑性功引入土体受力变形过程的能量方程中,推导得到土体流动法则。采用直线型屈服轨迹和非相关联流动法则,利用不排水应力路径计算得到硬化函数,建立了一个考虑颗粒破碎的粗粒土本构模型。对比分析表明：该模型对粗粒土在各种围压下的应力-应变和体应变计算结果与试验曲线吻合较好。 相似文献
15.
颗粒破碎是粒状材料在高应力状态下的一种基本现象。为了研究冻结砂土中颗粒破碎对应力应变关系的影响,将冻结砂土视为复合颗粒材料,忽略冰的压融,考虑内摩擦角随应力状态的变化,构建一个适用于冻结砂土的考虑颗粒破碎的非线性本构模型。构建过程分为三步,首先是基于三轴剪切前后颗粒分析对冻结砂土颗粒破碎模式和产生机理进行探讨;其次是基于考虑颗粒破碎的能量平衡方程,对冻土在三轴剪切试验过程中的颗粒破碎耗能进行分析,结果表明颗粒破碎耗能随轴向应变呈双曲线变化趋势;最后应用考虑颗粒破碎的剪胀方程修正沈珠江三参数非线性模型中的体积切线模量ν t,得到一个考虑颗粒破碎的非线性本构模型,模型参数可以通过单轴压缩试验和常规三轴试验确定。将原模型和修正后模型的计算结果与控制温度为-6℃,围压为1 MPa、4 MPa、6 MPa、8 MPa和10 MPa时冻结砂土的试验结果进行对比,结果表明该模型能够较好的模拟冻结砂土从低围压到高围压的应变软化特征与剪胀特征。 相似文献
16.
The paper provides an in-depth exploration of the role of particle crushing on particle kinematics and shear banding in sheared granular materials. As a two-dimensional approximation, a crushable granular material may be represented by an assembly of irregularly shaped polygons to include shape diversity of realistic granular materials. Particle assemblies are subjected to biaxial shearing under flexible boundary conditions. With increasing percentage of crushed particles, mesoscale deformation becomes increasingly unstable. Fragmented deformation patterns within the granular assemblies are unable to form stable and distinct shear bands. This is confirmed by the sparsity of large fluctuating velocities in highly crushable assemblies. Without generating distinct shear bands, deformation patterns and failure modes of a highly crushable assembly are similar to those of loose particle assemblies, which are regarded as diffuse deformation. High degrees of spatial association amongst the kinematical quantities confirm the key role that non-affine deformation and particle rotation play in the generation of shear bands. Therefore, particle kinematical quantities can be used to predict the onset and subsequent development of shear zones, which are generally marked by increased particle kinematic activity, such as intense particle rotation and high granular temperature. Our results indicate that shear band thickness increases, and its speed of development slows down, with increasing percentage of crushed particles. As particles crush, spatial force correlation becomes weaker, indicating a more diffuse nature of force transmission across particle contacts. 相似文献
17.
Various mechanisms can affect the permeability of dense unconsolidated sands: Volumetric dilation can lead to permeability increase, whereas strain localization in shear bands may increase or decrease the permeability depending on the state of compaction and on the level of grains breakage inside the band. To investigate these various mechanisms, an experimental study has been performed to explore the effect of different factors such as grain size and grain shape, confining pressure, level of shear, stress path, and formation of one or several shear bands on the permeability of dense sands under triaxial loading. The experimental results show a reduction of permeability during the consolidation phase and during the volumetric contraction phase of shear loading, which can be related to the decrease of porosity. The experimental results also show that, depending on the confining pressure, the permeability remains stable or decreases during the volumetric dilation phase despite the increase of total porosity. This permeability reduction is attributed to the presence of fine particles, which result from grains attrition during pre-localization and grains breakage inside the shear band during the post-localization phase. 相似文献
18.
This article deals with the effect of grain crushing on shear localization in granular materials during plane strain monotonic compression tests under constant lateral pressure. The grain diameter and the initial void ratio were stochastically distributed using a spatial correlation. To describe the mechanical behavior of cohesionless granular materials during a monotonic deformation path in plane strain compression, we used a micropolar hypoplastic constitutive model that is able to describe the salient properties of granular bodies including shear localization. The model was extended by introducing changes to the grain diameter with varying pressure using formulae from breakage mechanics proposed for crushable granulates. The initial void ratios and grain diameters took the form of correlated random spatial fields described by both symmetric and nonsymmetric random distributions using a homogeneous correlation function. The field realizations were generated with the help of an original conditional rejection method. A few representative samples of the random fields selected from the generated set were taken into account in numerical calculations. Copyright © 2011 John Wiley & Sons, Ltd. 相似文献
19.
为探讨颗粒形状对粒状材料的颗粒破碎演化规律及强度特征的影响,提出了一个新的粒状材料颗粒形状量化参数,设计了一种考虑三维颗粒形状的人工试样制备方法,随即进行了常规三轴压缩试验,并分析了颗粒破碎和强度特征,最终建立了一个二元介质强度准则,具体的研究成果为：建立颗粒形状量化参数——球形模量GM,在此基础上制备了5种不同形状的可破碎粒状材料三轴试样,并发现球形模量影响着粒状材料的三轴压缩强度特征;通过筛分确定试样的颗粒破碎情况,对试样的颗粒破碎演化规律和临界状态进行探讨,发现颗粒形状通过影响颗粒破碎规律而控制着宏观强度的非线性演化特征;以二元介质理论为基础,建立了考虑颗粒形状的可破碎粒状材料强度准则,并通过试验对其适用性进行了验证。 相似文献
20.
A practical combined finite–discrete element method was developed to simulate the breakage of irregularly shaped particles in granular geomaterials, e.g., rockfill. Using this method, each particle is discretized into a finite element mesh. The potential fracture paths are represented by pre-inserted cohesive interface elements (CIEs) with a progressive damage model. The Mohr–Coulomb model with a tension cut-off is employed as the damage initiation criterion to rupture the predominant failure mode occurs at the particle scale. Two series of biaxial tests were simulated for both the breakable and unbreakable particle assemblies. The two assemblies have identical configurations, with the exception that the former is inserted with CIEs and is breakable. The simulated stress–strain–dilation responses obtained for both assemblies are in agreement with experimental observations. We present a comprehensive study of the role of particle breakage on the mechanical behavior of rockfill materials at both the macroscopic and microscopic scales. The underlying mechanism of particle breakage can be explained by the force chain in the assemblies. 相似文献
|
