共查询到20条相似文献，搜索用时 31 毫秒
1.
由坡度和挡墙倾角的改变造成碎屑流冲击力学模型的改变是目前被忽略的问题。在碎屑流冲击倾式拦挡墙物理试验的基础上,利用离散元数值计算方法研究了坡度对碎屑流冲击立式拦挡墙（墙面与地面的夹角为90°）力学特征的影响,依据死区颗粒堆积特征,流动层颗粒冲击特征以及二者的相互作用特征提出了两种新力学模型：由倾斜冲击挡墙向坡面堆积转变的力学模型和考虑流动层对死区冲切摩擦作用的水平直接冲击力学模型。对不同冲击力学模型进行了验证分析,结果表明：坡度和挡墙倾角改变了死区的堆积特征从而改变了流动层的冲击方向和冲击力大小。当坡度小于40°时,碎屑流流动层首先沿死区上覆面倾斜冲击挡墙,在最大冲击力作用时刻,流动在坡面层状堆积,最大法向冲击合力可按静土压力公式估算。随着坡度的增大,在最大冲击力时刻,流动层颗粒直接冲击挡墙,但由于死区颗粒对流动层颗粒具有摩擦缓冲减速作用,大幅降低了流动层对挡墙的直接冲击力。此时死区对挡墙的作用力主要包括3个部分：流动层沿坡面冲击死区,由死区传递至挡墙的冲击力、流动层对死区的冲切摩擦力以及死区自重的静土压力。死区对挡墙作用力占最大法向冲击合力的比例增大至90%左右。当坡度由40°增大到50°时,在最大法向冲击合力作用时刻,流动层对死区的冲切摩擦力占最大冲击力的比例由15%增大到49%,流动层与死区之间的摩擦系数由滚动摩擦系数转变为静摩擦系数。提出的流动层对死区的冲切摩擦力为碎屑流冲击刚性挡墙力学计算模型提供了新的研究思路。 相似文献
2.
W. D. Guo 《国际地质力学数值与分析法杂志》2014,38(18):1969-1989
Recent study indicates that the response of rigid passive piles is dominated by elastic pile–soil interaction and may be estimated using theory for lateral piles. The difference lies in that passive piles normally are associated with a large scatter of the ratio of maximum bending moment over maximum shear force and induce a limiting pressure that is ~1/3 that on laterally loaded piles. This disparity prompts this study. This paper proposes pressure‐based pile–soil models and develops their associated solutions to capture response of rigid piles subjected to soil movement. The impact of soil movement was encapsulated into a power‐law distributed loading over a sliding depth, and load transfer model was adopted to mimic the pile–soil interaction. The solutions are presented in explicit expressions and can be readily obtained. They are capable of capturing responses of model piles in a sliding soil owing to the impact of sliding depth and relative strength between sliding and stable layer on limiting force prior to ultimate state. In comparison with available solutions for ultimate state, this study reveals the 1/3 limiting pressure (of the active piles) on passive piles was induced by elastic interaction. The current models employing distributed pressure for moving soil are more pertinent to passive piles (rather than plastic soil flow). An example calculation against instrumented model piles is provided, which demonstrates the accuracy of the current solutions for design slope stabilising piles. Copyright © 2014 John Wiley & Sons, Ltd. 相似文献
3.
The numerical simulation of rapid landslides is quite complex mainly because constitutive models capable of simulating the mechanical behaviour of granular materials in the pre‐collapse and post‐collapse regimes are still missing. The goal of this paper is to introduce a constitutive model capable of capturing the response of dry granular flows from quasi‐static to dynamic conditions, in particular when the material experiences a sort of solid‐to‐fluid phase transition. An ideal assembly of identical spheres under simple shear conditions is considered. In the constitutive model, void ratio and granular temperature have been chosen as state variables, and both shear and normal stresses are computed as the sum of two contributions: the quasi‐static one and the collisional one. The former is determined by using a perfect elasto‐plastic model including the critical state concept, while the latter is derived from the kinetic theory of granular gases. The evolution of the granular temperature, fundamentally governing the material phase transition, is obtained by imposing the kinetic fluctuating energy balance. The constitutive relationship has been integrated, under both constant pressure and constant volume conditions, and the influence of shear strain rate, initial void ratio and normal pressure on the mechanical response has been investigated. Copyright © 2015 John Wiley & Sons, Ltd. 相似文献
4.
Experimental Study of Dry Granular Flow and Impact Behavior Against a Rigid Retaining Wall 总被引：7，自引：1，他引：6
Shallow slope failure in mountainous regions is a common and emergent hazard in terms of its damage to important traffic routes and local communities. The impact of dry granular flows consisting of rock fragments and other particles resulting from shallow slope failures on retaining structures has yet to be systematically researched and is not covered by current design codes. As a preliminary study of the impact caused by dry granular flows, a series of dry granular impact experiments were carried out for one model of a retaining wall. It was indirectly verified that the total normal force exerted on a retaining wall consists of a drag force (F d), a gravitational and frictional force (F gf), and a passive earth force (F p), and that the calculation of F d can be based on the empirical formula defined in NF EN Eurocode 1990 (Eurocode structuraux. Base de calcul des structures, AFNOR La plaine Saint Denis, 2003). It was also indirectly verified that, for flow with Froude number from 6 to 11, the drag coefficient (C d) can be estimated using the previously proposed empirical parameters. 相似文献
5.
桩足够长、桩间距不大于6倍桩径的刚性桩复合地基中,在桩间土内部的剪切力和桩土间摩擦力共同作用下,桩顶段桩间土压力仅在一定深度范围内有所增加,且随深度迅速衰减,而桩顶段桩身轴力随深度增加。基于刚性桩复合地基的这一特点,紧邻刚性桩复合地基开挖基坑且基坑底高于刚性桩桩底时,得出刚性桩复合地基上的附加荷载作用在支护结构上的主动土压力可以简化为倒三角形,最大主动土压力作用在刚性桩桩顶平面与支护结构相交处,随深度增加,主动土压力迅速衰减至0。实践表明该计算方法比较符合工程实际。 相似文献
6.
Understanding the fundamental dynamics of interaction between multi-phase geophysical flows and engineering structures is crucial for mitigating geophysical hazards. Specifically, liquid phase between particles induces matric suction which could play a significant part in regulating flow dynamics and warrants further consideration. In this study, flume model tests were conducted to investigate the effects of water content (0–30%) on the impact behavior of granular flows. The particle image velocimetry technique was adopted to visualize the impact kinematics and the impact force was measured through a model barrier system. Results revealed that, besides geometric effects (kinetic sieving), mechanical effects (shearing and collision) are also vital for the mechanism of reverse segregation. At higher water contents, 20 and 30% in this study, discrete-surge impact, rather than a progressive impact process, was observed. The discrete surges induce impulses on the barrier. The discrete surges result from self-organization of unsaturated granular flows to overcome the enhanced shear strength induced by matric suction. Finally, a dimensionless index, namely the suction number, is used to quantify the effect of suction on the dynamic behavior of granular flows. Even for large-scale geophysical flows, if the content of fine particles is high, effect of suction should not be neglected. 相似文献
7.
We present a Lagrangian formulation for simulating the continuum hydrodynamics of dry granular flows based on multiplicative elastoplasticity theory for finite deformation calculations. The formulation is implemented within the smoothed particle hydrodynamics (SPH) method along with a variant of the usual dynamic boundary condition. Three benchmark simulations on dry sands are presented to validate the model: (a) a set of plane strain collapse tests, (b) a set of 3D collapse tests, and (c) a plane strain simulation of the impact force generated by granular flow on a rigid wall. Comparison with experimental results suggests that the formulation is sufficiently robust and accurate to model the continuum hydrodynamics of dry granular flows in a laboratory setting. Results of the simulations suggest the potential of the formulation for modeling more complex, field-scale scenarios characterized by more elaborate geometry and multi-physical processes. To the authors’ knowledge, this is the first time the multiplicative plasticity approach has been applied to granular flows in the context of the SPH method. 相似文献
8.
Understanding the interaction between complex geophysical flows and barriers remains a critical challenge for protecting infrastructure in mountainous regions. The scientific challenge lies in understanding how grain stresses in complex geophysical flows become manifested in the dynamic response of a rigid barrier. A series of physical flume tests were conducted to investigate the influence of varying the particle diameter of mono-dispersed flows on the impact kinematics of a model rigid barrier. Particle sizes of 3, 10, 23 and 38 mm were investigated. Physical tests results were then used to calibrate a discrete element model for carrying out numerical back-analyses. Results reveal that aside from considering bulk characteristics of the flow, such as the average velocity and bulk density, the impact load strongly depends on the particle size. The particle size influences the degree of grain inertial stresses which become manifested as sharp impulses in the dynamic response of a rigid barrier. Impact models that only consider a single impulse using the equation of elastic collision warrant caution as a cluster of coarse grains induce numerous impulses that can exceed current design recommendations by several orders of magnitude. Although these impulses are transient, they may induce local strucutral damage. Furthermore, the equation of elastic collision should be adopted when the normalized particle size with the flow depth, δ/h, is larger than 0.9 for Froude numbers less than 3.5. 相似文献
9.
挡土墙主动土压力的库仑统一解 总被引：6，自引：1，他引：5
基于极限平衡理论,视墙后填土为服从Mohr-Coulomb屈服准则的理想弹塑性材料,指出库仑土压力理论存在的一些缺陷,明确提出极限土压力是由墙后塑性土体产生,并假定塑性区的一族滑移线为直线,即平面滑裂面,建立了更为完善的滑楔分析模型,求解了在一般情况下考虑黏性土作用的挡土墙主动土压力、滑裂面土反力以及它们的分布,而经典库仑和朗肯主动土压力为其特例。 相似文献
10.
Flexible barriers undergo large deformation to extend the impact duration, and thereby reduce the impact load of geophysical flows. The performance of flexible barriers remains a crucial challenge because there currently lacks a comprehensive criterion for estimating impact load. In this study, a series of centrifuge tests were carried out to investigate different geophysical flow types impacting an instrumented flexible barrier. The geophysical flows modelled include covered in this study include flood, hyperconcentrated flow, debris flow, and dry debris avalanche. Results reveal that the relationship between the Froude number, Fr, and the pressure coefficient α strongly depends on the formation of static deposits called dead zones which induce static loads and whether a run-up or pile-up impact mechanism develops. Test results demonstrate that flexible barriers can attenuate peak impact loads of flood, hyperconcentrated flow, and debris flow by up to 50% compared to rigid barriers. Furthermore, flexible barriers attenuate the impact load of dry debris avalanche by enabling the dry debris to reach an active failure state through large deformation. Examination of the state of static debris deposits behind the barriers indicates that hyperconcentrated and debris flows are strongly influenced by whether excessive pore water pressures regulate the depositional process of particles during the impact process. This results in significant particle rearrangement and similar state of static debris behind rigid barrier and the deformed full-retention flexible barrier, and thus the static loads on both barriers converge. 相似文献
11.
单锚类土质边坡锚固预应力传递规律的研究 总被引：1，自引：1，他引：0
在前人理论上推导的基础上,进一步计算了类土质边坡单锚预应力自坡面向坡体内的传递范围,计算了坡体内不同位置处的预应力传递系数,分析得出单锚预应力自坡面向坡体内传递的扩散角为39°左右、合理锚间距为3.2 m左右。以G323改造工程K617段花岗岩风化形成的类土质边坡为原型进行了离心模型试验,在坡体模型内不同位置埋设土压力盒,通过测读土压力盒的读数,得出预应力在坡体内不同位置处引起的土压力变化,间接得出预应力自坡面向坡体内的传递规律。离心模型试验得出的预应力传递规律与理论推导得出规律基本吻合,并得出了预应力传递系数与初始锚固预应力有关的结论,认为这主要是因为边坡岩土体产生塑性形变的结果。理论分析和离心模型试验均得出,锚固措施对近坡面处的浅层土体并无明显的加固作用,锚固边坡也必须进行坡面防护。 相似文献
12.
In this work, the interface behavior between an infinite extended narrow granular layer and a rough surface of rigid body is investigated numerically, using finite element method in the updated Lagrangian (UL) frame. In this regard, the elasto‐plastic micro‐polar (Cosserat) continuum approach is employed to remove the limitations caused by strain‐softening of materials in the classical continuum. The mechanical properties of cohesionless granular soil are described with Lade's model enhanced by polar terms, including Cosserat rotations, curvatures, and couple stresses. Furthermore, the mean grain diameter as the internal length is incorporated into the constitutive relations accordingly. Here, the evolution and location of shear band, within the granular layer in contact with the rigid body, are mainly focused. In this regard, particular attention is paid to the effects of homogeneous distribution and periodic fluctuation of micro‐polar boundary conditions, prescribed along the interface. Correspondingly, the effects of pressure level, mean grain diameter, and stratified soil are also considered. The finite element results demonstrate that the location and evolution of shear band in the granular soil layer are strongly affected by the non‐uniform micro‐polar boundary conditions, prescribed along the interface. It is found that the shear band is located closer to the boundary with less restriction of grain rotations. Furthermore, the predicted thickness of shear band is larger for higher rotation resistance of soil grains along the interface, larger mean grain diameter, and higher vertical pressure. Regarding the stratified soil, comprising a thin layer with slightly different initial void ratio, the shear band moves towards the layer with initially higher void ratio. Copyright © 2011 John Wiley & Sons, Ltd. 相似文献
13.
The impact force to a rigid obstruction from a granular mass sliding down a smooth incline provides insights into the solid-like and fluid-like behaviors of granular avalanches and useful information for risk assessment and engineering design against landslides. In this study, a series of 2-D flume tests were performed to systematically investigate the effects of inclination angle, sliding distance, and initial relative density on the flow front velocity and impact force on a rigid obstruction. The experimental results show that for inclination angles smaller than the critical state friction angle of sand, an increase in the sliding distance and/or initial relative density results in smaller impact forces; for higher inclination angles, the trend is reversed. Based on the experimental results, an analytical equation is proposed to estimate the flow front velocity and an empirical approach is presented to estimate the maximum impact force based on elastic solid and hydrodynamic methods. The proposed equations are found to provide more accurate predictions for the maximum impact force than similar equations in the literature. 相似文献
14.
从水平简谐振动作用下二维土?悬臂式刚性墙计算模型出发,基于波动力学理论,同时考虑土层的竖向应力和竖向位移,对二维场地中悬臂式刚性墙的动力响应特性进行了解析研究。首先对土层振动方程进行变换,得到关于体积应变? 的方程,通过分离变量法进行求解,再回代振动方程得到关于位移运动方程的非齐次方程,结合墙与土层的相互作用条件及远场边界条件得到振动方程定解,进而得到地下刚性墙墙上土压力、墙底剪力及弯矩的更为严格的解析解。将所得解与忽略竖向应力解、忽略竖向位移解进行了对比。研究表明,所得解能多反映出一个共振频率,且当土体泊松比大于0.45时,忽略竖向位移解失去意义。通过参数分析,表明激励频率与土体阻尼因子对墙体动力响应影响较大,考虑的振动模态阶数对墙体动力响应影响较小。 相似文献
15.
The aim of this study is to numerically model the fracture system at percussive drilling. Because of the complex behavior of rock materials, a continuum approach is employed relying upon a plasticity model with yield surface locus as a quadratic function of the mean pressure in the principal stress space coupled with an anisotropic damage model. In particular, Bohus granite rock is investigated, and the material parameters are defined based on previous experiments. This includes different tests such as direct tension and compression, three‐point bending, and quasi‐oedometric tests to investigate the material behavior at both tension and confined compression stress states. The equation of motion is discretized using a finite element approach, and the explicit time integration method is employed. Edge‐on impact tests are performed, and the results are used to validate the numerical model. The percussive drilling problem is then modeled in 3D, and the bit‐rock interaction is considered using contact mechanics. The fracture mechanism in the rock and the bit penetration‐ resisting force response are realistically captured by the numerical model. Copyright © 2013 John Wiley & Sons, Ltd. 相似文献
16.
Carlos Lam Julian S. H. Kwan Y. Su Clarence E. Choi Charles W. W. Ng 《Landslides》2018,15(9):1779-1786
This paper reports an investigation on the performance of ethylene-vinyl acetate (EVA) foam when used as a cushion layer for rigid barriers used to resist debris flow. Large-scale pendulum impact tests were conducted to study the effects of layer thickness on cushion performance under six successive impacts. Results show that for the first impact at 70 kJ, the peak contact force with the EVA foam thickness of 500 mm is about twice larger compared to that of 1000 mm. Results also reveal that the cushion mechanism of elastic collapse of cell walls in the EVA foam results in peak contact forces and maximum transmitted loads that are up to 30 and 50% lower compared to gabions for the first impact at 70 kJ, respectively. The elastic behavior of EVA foam provides consistent cushioning efficiency. Furthermore, EVA foam is found to be susceptible to degradation by ultraviolet light so that a suitable coating layer is required for outdoor use. Polyurea was identified as a suitable coating material and a small-scale coating trial was performed to confirm this. Findings presented in this paper will have direct implications on the future design of cushion layers for rigid barriers used to intercept debris flows. 相似文献
17.
18.
An approximate two‐dimensional model for indentation of blunt objects into various types of rigid‐perfectly plastic cohesive‐frictional material is derived. Particular emphasis is placed on considering indentation as a process involving evolution of the boundary of material displaced by the indenter. Force–penetration relationships are obtained by an incremental approach utilizing key kinematic and static information from indentation of a flat punch. Albeit approximate, the proposed model applies to arbitrary indenter geometry and weightless or ponderable cohesive‐frictional materials exhibiting associated or non‐associated plastic flow. Two specific indenter geometries, the cylinder and blunt wedge, are explored in detail. Favorable agreement is found between the analytic results and those obtained using the finite element method (FEM). For both the wedge and cylinder, it is further shown that accurate analytic expressions relating indentation force explicitly to penetration can be derived. In the case of the wedge and weightless material, predictions of indentation force obtained from the derived expressions are very close to those computed from implicit equations available in the literature. Copyright © 2011 John Wiley & Sons, Ltd. 相似文献
19.
On 13 August 2010, significant debris flows were triggered by intense rainfall events in Wenchuan earthquake-affected areas, destroying numerous houses, bridges, and traffic facilities. To investigate the impact force of debris flows, a fluid–structure coupled numerical model based on smoothed particle hydrodynamics is established in this work. The debris flow material is modeled as a viscous fluid, and the check dams are simulated as elastic solid (note that only the maximum impact forces are evaluated in this work). The governing equations of both phases are solved respectively, and their interaction is calculated. We validate the model with the simulation of a sand flow model test and confirm its ability to calculate the impact force. The Wenjia gully and Hongchun gully debris flows are simulated as the application of the coupled smoothed particle hydrodynamic model. The propagation of the debris flows is then predicted, and we obtain the evolution of the impact forces on the check dams. 相似文献
20.
In this paper, we present the exact solution of the Riemann problem for the nonlinear one‐dimensional so‐called shallow‐water or Saint‐Venant equations with friction proposed by SAVAGE and HUTTER to describe debris avalanches. This model is based on the depth‐averaged thin layer approximation of granular flows over sloping beds and takes into account a Coulomb type friction law with a constant friction coefficient. A particular configuration of the Riemann problem corresponds to a dam of infinite length in one direction from which granular material is released from rest at a given time over an inclined rigid or erodible bed. We solve analytically and numerically the depth‐averaged long‐wave equations derived in a topography‐linked coordinate system for all the possible Riemann problems. The detailed mathematical proof of the derivation of the analytical solutions and the analysis of their structure and properties is intended, first of all, for geophysicists, mathematicians, and physicists because of the possible extension of this study to more complex problems (geometries, friction laws, …). The numerical solution of the first‐order finite‐volume method based on a Godunov‐type scheme is compared with the proposed exact Riemann problem solution. This solution is used to solve the dam‐break problem and analyze the influence of the thickness of the erodible bed on the speed of the granular front. Comparison with existing experimental results shows that, for an erodible bed, the equations lack fundamental physical significance to reproduce the observed dynamics of erosive granular flows. Copyright © 2012 John Wiley & Sons, Ltd. 相似文献