共查询到20条相似文献，搜索用时 468 毫秒
1.
用半解析方法研究孤立的截断的浮式Spar平台主体的一阶绕射问题,在入射波浪周期为4～40 s的范围内分别得到迎浪0(°)和45(°)角时的纵荡激励力、垂荡激励力和纵摇激励力矩图,得到的数值计算结果与MOSES和WAMIT应用软件计算结果一致.所得计算结果,可应用于Spar平台的运动计算. 相似文献
2.
本文给出有限水深二维物体二阶绕射势在外域中的解析表达式，从而准确满足二阶绕射势的辐射条件。二阶绕射势在内域自由表面上的边界条件则由一阶势的数值微分求得。然后对内域用简单Ｇｒｅｅｎ函数法求得二阶绕射势。本文对二维浮体和潜体在不同水深和潜深情况下的绕射问题进行了计算，求得了二阶绕射势和二阶定常及倍频波浪力。讨论了水深和潜深对波浪力的影响以及二阶绕射势对非线性波浪力的贡献 相似文献
3.
浮式防波堤非线性波浪力实验研究 总被引：2，自引：1，他引：2
对浮式防波堤在不同吃水深度、周期、波高和入射波波型情况，进行了波浪对浮式防波堤非线性作用力的研究，给出了有关实验结果。实验结果表明波浪力在周期较大时，随着波高的增加，出现一阶力减小、高阶力增大的强非线性现象。实验中出现了二阶力大于一阶力的现象，也出现了三阶力大于二阶力和一阶力的现象。 相似文献
4.
冰区四季通用灯浮标是一种为满足北方冬季冰冻港口一年四季的助航服务需求研制的新型灯浮标,二阶波浪力对其漂浮姿态和漂移运动有较大影响。文中研究了浮标受到的二阶波浪力的数值计算方法,计算了不同流速下罐形和锥形灯浮标的二阶波浪力。研究结果显示,罐形和锥形灯浮标受到的一阶波浪力相差不大,罐形的二阶波浪力明显小于锥形,具有一定的外形优势。 相似文献
5.
6.
应用非线性谱分析理论，对三阶Stokes型随机波浪载荷谱进行了分析，将波面方程及海水质点的水平速度用一阶波面的非线性组表示，导出了随机波浪谱的表达式。为了便于求解随机波浪的载荷谱，将阻力项展开为幂级数式，并应用非线性谱分析理论，确定了幂级数的系数，进而将波浪载荷表示为一阶波面及其导数的非线性组合，最后得出波浪载荷谱密度的表达式，并应用数值分析方法，得出单位桩柱波浪力及总波浪力谱密度。 相似文献
7.
应用理论推导及数值计算方法，对Stokes随机波的谱特性进行了分析。首先将波面方程，海水质点水平速度用一阶波面分量的非线性组合表示，应用平稳随机高阶短的降阶计算法则，得到了波面方程及海水质点水平速度与一阶波面分量的自相关函数之间的关系，从而确定了Stokes随机波浪的波浪谱密度及海水质点水平速度和加速度谱密度，进而求得有关波浪要素的均方根值。文章还应有数值计算方法，分析了波浪基本参数对均方根值的影响。 相似文献
8.
方形网箱水平波浪力的迭加计算和实验验证 总被引：4，自引：3，他引：4
采用小直径圆柱体绕流理论和网渔具理论为基础的经验水动力计算法，分别考虑网箱框架是刚性体、网衣和绳索是柔性体的特征，结合正弦波理论对方形网箱及其构件受到的水平波浪力特性进行了分析研究，理论给出了波浪力迭加计算法，并把计算结果与小尺度的网箱水槽实验进行对比验证。结果表明，计算数值与试验数据较接近，平均误差率在15％以内。网箱水平波浪力呈周期性、不对称变化，在波浪周期小于0.72s时，主要以框架的波浪力为主，反之以网衣的为主。在波长为0.8m、周期为0.72s、水深为0.7m、波高为68.3mm情形下，计算结果显示网箱的框架尺寸和形状及其系泊、布局的选择应根据实际海况而定，网箱高度可适当增加，当设置水层下降深度相对于网箱高度比率为20％-40％，时，波浪力峰值下降相对率达68.03％-88.20％，表明可以较大程度地降低其波浪力。 相似文献
9.
通过理论研究定量地说明流向Morison波浪力,即拖曳力和惯性力的高阶统计矩随采样次数增加的规律.主要应用二阶Stokes波理论,推导了流向Morison波浪力的前四阶累积量.计算了作用于实际海底管线上的流向Morison波浪力的偏斜度和峰度.结果表明,随着采样次数的增加,拖曳力和惯性力的偏斜度和峰度驱于收敛.文中给出的方法为后续理论工作奠定了基础. 相似文献
10.
11.
Chandralata Raghukumar G. Sheelu P. A. Loka Bharathi Shanta Nair C. Mohandass 《Marine Georesources & Geotechnology》2001,19(1):1-16
In order to assess the impact of deep-sea mining on the in situ benthic life, we measured the microbial standing stock and concentration of organic nutrients in the deep-sea sediments of the Central Indian Ocean Basin in the Indian pioneer area. Sediments were collected using box core and grab samples during September 1996. The total bacterial numbers ranged from 10 10 -10 11 cells per g -1 dry weight sediment. There was a marginal decrease in the number of bacteria from surface to 30 cm depth, though the subsurface section registered a higher number than did the surface. The highest numbers were encountered at depths of 4-8 cm. The retrievable number of bacteria were two orders less in comparison with the direct total counts of bacteria. An almost homogeneous distribution of bacteria, total organic carbon, living biomass, and lipids throughout the depth of cores indicates active microbial and benthic processes in the deep sea sediments. On the other hand, a uniform distribution of total counts of bacteria, carbohydrates, and total organic carbon in all the cores indicates their stable nature and suggests that they can serve as useful parameters for long-term monitoring of the area after the benthic disturbance. Further studies on temporal variability in this region would not only verify the observed norms of distribution of these variables but would also help to understand restabilization processes after the simulated benthic disturbance. 相似文献
12.
Derek V. Ellis 《Marine Georesources & Geotechnology》2001,19(1):51-63
This article reviews information recently available from existing marine and coastal mining for responses to environmental issues affecting marine mining at different depths. It is particularly but not exclusively concerned with those issues affecting seabed biodiversity impact and recovery. Much information has been gathered in the past 10 years from shallow mining operations for construction aggregate, diamonds, and gold, from coastal mines discharging tailings to shallow and deep water, and from experimental deep mining tests. The responses to issues identified are summarized in a series of eight tables intended to facilitate site-specific consideration. Since impacts can spread widely in the surface mixing layer SML, and can affect the biologically productive euphotic zone, the main issues considered arise from the depth of mining relative to the SML of the sea. Where mining is below the SML, the issue is whether it is environmentally better to bring the extraction products to the surface vessel for processing (and waste discharge), or to process the extraction products as much as possible on the seabed. Responses to the issues need to be sitespecific, and dependent on adequate preoperational environmental impact and recovery prediction. For deep tailings disposal from a surface vessel, there are four important environmental unknowns: (1) the possible growth of "marine snow" (bacterial flocs) utilizing the enormous quantities of fine tailings particles (hundreds or thousands of metric tons per day) as nuclei for growth, (2) the possibility that local keystone plankton and nekton species may migrate diurnally down to and beyond the depth of deep discharge and hence be subjected to tailings impact at depth, (3) the burrow-up capability of deep benthos and their ability to survive high rates of tailings deposition, and (4) the pattern and rate of dispersion of a tailings density current through the deep water column from discharge point to seabed. Actions to obtain relevant information in general and site-specifically are suggested. 相似文献
13.
G. Parthiban 《Marine Georesources & Geotechnology》2000,18(3):223-235
Particle fluxes were measured 7 m above the sea bottom during the predisturbance, disturbance, and postdisturbance periods by using time series sediment traps attached to seven deep-sea moorings deployed in the INDEX experiment site in the Central Indian Basin. The predisturbance particle fluxes varied between 22.3 to 55.1 mg m -2 day -1 . Increased and variable particle fluxes were recorded by the sediment traps during the disturbance period. The increase observed was 0.5 to 4 times more than the background predisturbance fluxes. The increases in particle fluxes (~4 times) recorded by the sediment trap located in the southwestern direction (DMS-1) were the greatest, which could be the result of preferential movement of resuspended particles generated during the deep-sea benthic disturbance along the general current direction prevailing in this area during the experimental period. Also, the traps located closer to the disturbance area recorded greater fluxes than did the traps far away, across the Deep Sea Sediment Resuspension System path. This variability in recorded particle fluxes by the traps around the disturbance area clearly indicates that physical characteristics such as grain size and density of the resuspended particles produced during the disturbance had an important effect on particle movement. The postdisturbance measurements during ~5 days showed a reduction in particle fluxes of ~50%, indicating rapid particle settlement. 相似文献
14.
Arne Schnack-Friedrichsen Angela M. Davis Jim D. Bennell Dei G. Huws 《Marine Georesources & Geotechnology》2001,19(4):221-243
The interdependence between the seismo-acoustic properties of a marine sediment and its geotechnical/physical parameters has been known for many years, and it has been postulated that this should allow the extraction of geotechnical information from seismic data. Though in the literature many correlations have been published for the surficial layer, there is a lack of information for greater sediment depths. In this article, a desktop study on a synthetic seafloor model illustrates how the application of published near-surface prediction equations to subsurface sediments (up to several tens of meters burial depth) can lead to spurious predictions. To test this further, acoustic and geotechnical properties were measured on a number of sediment core samples, some of which were subjected to loading in acoustically-equipped consolidation cells (oedometers) to simulate greater burial depth conditions. For low effective pressures (representing small burial depths extending to around 10 meters subsurface), the general applicability of established relationships was confirmed: the prediction of porosity, bulk density, and mean grain size from acoustic velocity and impedance appears generally possible for the investigated sedimentary environments. As effective pressure increases through, the observed relationships deviate more and more from the established ones for the near-surface area. For the samples tested in this study, in some instances increasing pressure even resulted in decreasing velocities. There are several possible explanations for this abnormal behavior, including the presence of gas, overconsolidation, or bimodal grain size distribution. The results indicate that an appropriate depth correction must be introduced into the published prediction equations in order to obtain reliable estimates of physical sediment properties for greater subsurface depths. 相似文献
15.
Geoacoustic Inversion via Genetic Algorithm and Its Application to Manganese Sediment Identification
An acoustic inversion method using a wide-band signal and two near field receivers is proposed and applied to multiple layered seabed models including a manganese sediment. The inversion problem can be formulated into a probabilistic model comprised of signals, a forward model, and additive noise. The forward model simulates wide-band signals, such as chirp signals, and is chosen to be the source-waveletconvolution plane wave modeling method. The wavelet matching technique, using weighted least-squares fitting, estimates the sediment sound-speed and thickness on which determination of the possible numerical ranges for a priori uniform distribution is based. The genetic algorithm is applied to a global optimization problem to find a maximum a posteriori solution for determined a priori search space. Here the object function is defined by an L 2 norm of the difference between measured and modeled signals. Not only the marginal pdf but also its statistics are calculated by numerical evaluation of integrals using the samples selected during importance sampling process of the genetic algorithm. 相似文献
16.
海上大直径钢管桩打桩过程中,桩周土体受到强烈扰动而发生强度弱化,掌握桩周土体强度弱化规律对于准确预测打桩过程、保证工程安全具有重要意义。为研究土体强度弱化规律,开展了环剪试验模拟打桩对桩周土体的扰动,测试土体强度随剪切速率的变化规律,建立了描述土体强度弱化规律的拟合公式,引入到打桩分析软件中。研究结果表明：土体的强度折减程度不仅与土体本身的性质有关还受到土体的埋深和剪切速率的影响,埋深越深土体强度折减程度越低,剪切速率越高土体强度折减越高,在打桩分析中可采用这里推荐的线性折减方法来模拟不同深度处土体强度的折减规律。 相似文献
17.
The advanced piston corer (APC) has been used by the Ocean Drilling Program since 1985 for recovering soft sediments from the ocean floor. The pullout force measured on extracting the core barrel from the sediment is shown to correlate with the average shear strength of the sediment core measured in the ship's laboratory. A simple rule of thumb is derived relating the shear strength of the sediment to the pullout force. Multiple APC holes at individual sites allow the consistency of the pullout measurements to be assessed. The effects of different operational procedures during APC coring are also explored. Although generally applicable, the correlation between pullout force and laboratory measurements of shear strength breaks down for some APC holes, possibly because of the disturbance of some sediment types during the APC coring process. A better understanding of the physical process of APC coring, and its effect on the properties of the sediment both inside and immediately outside the core barrel, would indicate what confidence can be put on the measurement of pullout force as a way of evaluating the in situ shear strength of deep sea sediments. 相似文献
18.
Shigehisa Nakamura 《Marine Geodesy》2000,23(1):55-61
Specific properties of the interannual sea level variations and annual tides in the Northwestern Pacific were studied. Several tide stations were monitored. The monthly mean sea level for the year of 1995 was analyzed at each tide station. A seismic event in 1995, some tectonic activity around the subject area, and the Kuroshio (the oceanic western boundary current) may possibly contaminate results which would have occurred from the astronomical annual tide alone. 相似文献
19.
20.