共查询到19条相似文献，搜索用时 171 毫秒
1.
海底地形是全球地形的重要组成部分,对地球物理科学研究、经济活动等具有重要作用。基于Parker公式,利用卫星测高重力异常和船测水深数据,采用频域的方法反演了疑似马航MH370失事区域的留尼汪海域的10°×10°的海底地形。最后将反演的水深和船测水深、国际通用的海深模型ETOPO1作比较进行精度评估,结果表明:本文反演结果与船测水深相比误差平均值为-26.038 m,标准差为176.588 m;与ETOPO1相比,差异平均值为-33.541 m,标准差为160.769 m。这表明采用重力异常数据,结合船测数据能较高精度地反演海底地形。 相似文献
2.
随着测高技术的不断发展,测高海洋重力场的精度不断提高,由其反演计算的海底地形精度也相应提高。利用Sandwell 2014年最新发布主要由Jason-1末期大地测量任务和Cryosat-2观测资料反演的测高重力场V23.1,采用重力地质法(GGM)反演了中国南海海域海底地形模型,并对结果进行了精度评价。该过程中首先直接计算一系列密度差下的反演结果,并通过船测数据检核选定优化的密度差范围,然后利用向下延拓的方法确定了最优密度差异常数为7g/cm3。与船测水深数据相比,反演得到的GGM模型与检核点船测水深数据差值的标准差达到了±70.32m;此外,还计算了由测高重力异常V15.2反演的海底模型,比较这两个模型发现:测高重力场短波部分的改善对海底地形反演精度的提升作用有限,为得到更高精度的海底地形模型,需引入短波更为敏感的重力梯度资料。 相似文献
3.
根据重力地质法(Gravity Geological Method, GGM),利用6 736个已知水深点数据和卫星测高重力异常反
演了马里亚纳海沟(142°36''~147°18''E,23°~27°N)1''×1''分辨率的海底地形,该计算中的密度差常数为1.20 g/cm3。将反演的地形与实测检核水深数据相比,两者较差标准差为152.9 m,平均误差为(±3.0) m,均方差为153.0 m,优于ETOPO1模型和直接把船测水深控制点格网化后的模型。将重力地质法反演的模型、ETOPO1模型、直接格网模型进行功率谱密度分析,结果显示3种模型在中长波地形能量一致,但对于短波地形,重力地质法模型能量高于其他2个模型,说明重力地质法更能描绘细致的海底地形地貌。选取2条测线与重力地质法模型进行对比研究,结果表明重力地质法在海底地形起伏小的区域优于在海底地形起伏较大区域的反演效果。 相似文献
4.
研究了基于EGM2008大地水准面模型的高程传递原理,通过青岛地区已知控制点数据计算得到EGM2008大地水准面模型与我国大地水准面差距,利用EGM2008模型计算高程异常的方法,结合GNSS技术实现高程传递。利用青岛市C级GNSS控制网数据,基于EGM2008模型,采用3种不同的拟合方法,建立了区域高程异常残差场,反演高程异常值与已知控制点高程异常值进行比对。利用青岛市D级GNSS点的数据对构建的格网模型的精度进行检核。结果表明:EGM2008大地水准面模型与我国的大地水准面存在22 cm左右的偏差;基于EGM2008模型的高程传递精度可达厘米级,可用于近海高程传递,几种拟合方法精度相当。 相似文献
5.
基于重力地质法(GGM)采用卫星重力异常数据反演了中国南海112°E~119°E,16°N~20°N范围1'×1'的海底地形模型,通过船测水深数据的直接格网化结果和ETOP01模型的检核进行了精度评价。结果表明,GGM模型较船测水深的直接格网化结果更为精细,在船测控制点分布均匀的海域,GGM模型能获得比ETOP01模型更高的精度。为进一步验证GGM模型受海底地形特征影响的情况,采用GGM模型与ETOP01模型分别内插出9356个检核点处的水深,并统计得到两模型差值的较差结果平均值为19.560m,标准差为130.156m,相对精度为4.79%。经分析得出:GGM模型与ETOP01模型在坡度变化平缓深海区有着较好的一致性,随着水深的依次变浅,二者的差异逐渐显现,在多海山的海域差异达到最大。最后,为充分发挥重力地质法在海底地形反演中的优势总结了其最佳适用条件。 相似文献
6.
用Geosat高度计数据提取东海大地水准面 总被引：4，自引：1，他引：4
大地水准面是地球重力势等势面,它反映了地球形状及海面重力场异常特征,对大地测量学及海底探矿意义重大.本文利用Geosat高度计50个ERM周期共2.3a的数据,对包括东海区域的20°～40°N,120°～140°E海域进行了大地水准面反演计算.本文采用时间平均处理法有效地抑制了高度计数据中含有的由海洋时变因素引起的高度偏差,并用两种计算模型得到了东海大地水准面.计算出的大地水准面可反映出某些小区域海底特征,但与大尺度海底地形相关较差,这主要是由地壳均衡补偿作用引起的.对计算误差分析得出,采用模型-1和模型-2得出的大地水准面中残留的轨道误差分别为10.8和5.6cm,与OSU91A大地水准面模型偏差分别为37.6和42.2cm,时间平均处理使海洋时变因素引起的海面高度偏差降低了7倍. 相似文献
7.
针对基于测高重力异常反演海底地形理论众多、选取标准无法确定的情况,利用中国南海海域内的测高重力异常和船测水深数据研究比较了重力地质法(GGM)和SmithSandwell (SAS)法两种精度高、计算速度相对较快的海底地形反演理论。其中,GGM方法的密度差异常数Δρ由向下延拓技术确定为2.15 g·cm-3,SAS方法采用移去-恢复技术得到反演波段内重力异常和水深数据。结果表明:测线分布条件一定时,水深多在-1 000 m左右或反演区域岛礁、海山等复杂海底地形较多时选取SAS方法,水深主要在-3 000 m以深的区域或海底地形复杂程度不高时选取GGM方法则能获取更好的效果,其效果最优处与船测水深在检核点处的差值最优平均值能达-0.61 m,标准差可达14.67 m。 相似文献
8.
9.
卫星测高在海洋测绘中的应用 总被引：1，自引：0，他引：1
研究了卫星测高数据在海山探测以及无图海域水深预测方面的应用。介绍了匹配滤波法检测海山的理论与方法，并研究了反演海底地形时的重力导纳理论以及滤波窗口和滤波函数的选择。实践表明，利用卫星测高数据反演海底地形的精度可优于水深的10％。 相似文献
10.
11.
《Marine Geodesy》2012,35(1):63-85
AbstractWe introduce an iterative inversion method to address the problems in high-order seafloor topography inversion using gravity data (gravity anomaly and vertical gravity gradient anomaly), such as the difficulty in computing the equation and the uniqueness of the calculation results. A part of the South China Sea is selected as the experimental area. Considering the coherence and admittance function of gravity topography and vertical gravity gradient topography, the inversion band of the gravity anomaly and vertical gravity gradient anomaly in the study area is 30?km–120?km. Seafloor topography models of different orders are constructed using an iterative method, and the performance of each seafloor topography model is analyzed against ETOPO1 and other seafloor topography models. The experimental results show that as the inversion order increases, the clarity and richness of seafloor topographic expression continuously improve. However, the accuracy of seafloor topography inversion does not improve significantly when the inversion order exceeds a certain value, which is related to the contribution of high-order seafloor topography to gravity information. The results show that the accuracy of BGT4 (inversion model constructed by the gravity anomaly) is slightly poorer than that of BVGGT4 (inversion model constructed by the vertical gravity gradient anomaly) in areas with complex topography, such as multi-seamounts and trenches, and the results are generally better in areas with flat seafloor topography. 相似文献
12.
Min zhang Hu Jian cheng Li Hui Li Chong Yang Shen Tao yong Jin Le lin Xing 《Marine Geodesy》2013,36(2):176-189
A new one-minute global seafloor topography model was derived from vertical gravity gradient anomalies (VGG), altimetric gravity anomalies, and ship soundings. Ship soundings are used to constrain seafloor topography at wavelengths longer than 200 km and to calibrate the topography to VGG (or gravity) ratios at short wavelengths area by area. VGG ratios are used to predict seafloor topography for wavelength bands of 100–200 km and to suppress the effect of crust isostasy. Gravity anomalies are used to recover seafloor topography at wavelengths shorter than 100 km. The data processing procedure is described in detail in this paper. The accuracy of the model is evaluated using ship soundings and existing models, including General Bathymetric Charts of the Oceans (GEBCO), DTU10, ETOPO1, and SIO V15.1. The results show that, in the discussed regions, the accuracy of the model is better than ETOPO1, GEBCO, and DTU10. Additionally, the model is comparable with V15.1, which is generally believed to have the highest accuracy. In the north-central Pacific Ocean, the accuracy of the model increased by approximately 29.5% compared with the V15.1 model. This indicates that a more accurate seafloor topography model can be formed by combining gravity anomalies, VGG, and ship soundings. 相似文献
13.
This study concerns the determination of a regional geoid model in the North Atlantic area surrounding the Azores islands by combining multi-mission altimetry from the ERS (European Remote Sensing) satellites and surface gravity data. A high resolution mean sea surface, named AZOMSS99, has been derived using altimeter data from ERS-1 and ERS-2 35-day cycles, spanning a period of about four years, and from ERS-1 geodetic mission. Special attention has been paid to data processing of points around the islands due to land contamination on some of the geophysical corrections. A gravimetric geoid has been computed from all available surface gravity, including land and sea observations acquired during an observation campaign that took place in the Azores in October 1997 in the scope of a European and a Portuguese project. Free air gravity anomalies were derived by altimetric inversion of the mean sea surface heights. These were used to fill the large gaps in the surface gravity and combined solutions were computed using both types of data. The gravimetric and combined solutions have been compared with the mean sea surface and GPS (Global Positioning System)-levelling derived geoid undulations in five islands. It is shown that the inclusion of altimeter data improves geoid accuracy by about one order of magnitude. Combined geoid solutions have been obtained with an accuracy of better than one decimetre. 相似文献
14.
This study concerns the determination of a regional geoid model in the North Atlantic area surrounding the Azores islands by combining multi-mission altimetry from the ERS (European Remote Sensing) satellites and surface gravity data. A high resolution mean sea surface, named AZOMSS99, has been derived using altimeter data from ERS-1 and ERS-2 35-day cycles, spanning a period of about four years, and from ERS-1 geodetic mission. Special attention has been paid to data processing of points around the islands due to land contamination on some of the geophysical corrections. A gravimetric geoid has been computed from all available surface gravity, including land and sea observations acquired during an observation campaign that took place in the Azores in October 1997 in the scope of a European and a Portuguese project. Free air gravity anomalies were derived by altimetric inversion of the mean sea surface heights. These were used to fill the large gaps in the surface gravity and combined solutions were computed using both types of data. The gravimetric and combined solutions have been compared with the mean sea surface and GPS (Global Positioning System)-levelling derived geoid undulations in five islands. It is shown that the inclusion of altimeter data improves geoid accuracy by about one order of magnitude. Combined geoid solutions have been obtained with an accuracy of better than one decimetre. 相似文献
15.
Michael P. Stewart Will E. Featherstone Jonathan F. Kirby Mark Dumville 《Marine Geodesy》2013,36(4):319-330
Sea surface height profiles derived from 2‐year, repeat track, Geosat altimeter data have been compared with a regional gravimetric geoid in the western North Sea, computed using a geopotential model and terrestrial gravity data. The comparison encompasses 18 Geosat profiles covering a 750 × 850 km area of the North Sea. After a second‐order polynomial was used to model the long‐wavelength differences which cannot be clearly separated over an area of this size, results show agreement to better than ±3 cm for wavelengths between approximately 20 and 750 km. In regions where terrestrial gravity data were not available to improve the geoid, similar comparisons with the OSU91A geopotential model alone show differences of up to ±6 cm. This illustrates the importance of incorporating local gravity data in regional geoid computations, and partly validates the regional gravimetric geoid solution and Geosat sea surface profiles in the western North Sea. It is concluded that, in marine areas where the sea surface topography is known to be small in magnitude, Geosat sea surface profiles can act as an independent control on gravimetric geoids in the medium‐wavelength range. 相似文献
16.
Robert E. Cheney Bruce C. Douglas David T. Sandwell James G. Marsh Thomas V. Martin John J. McCarthy 《Marine Geophysical Researches》1984,7(1-2):17-32
Satellite-borne altimeters have had a profound impact on geodesy, geophysics, and physical oceanography. To first order approximation,
profiles of sea surface height are equivalent to the geoid and are highly correlated with seafloor topography for wavelengths
less than 1000 km. Using all available Geos-3 and Seasat altimeter data, mean sea surfaces and geoid gradient maps have been
computed for the Bering Sea and the South Pacific. When enhanced using hill-shading techniques, these images reveal in graphic
detail the surface expression of seamounts, ridges, trenches, and fracture zones. Such maps are invaluable in oceanic regions
where bathymetric data are sparse. Superimposed on the static geoid topography is dynamic topography due to ocean circulation.
Temporal variability of dynamic height due to oceanic eddies can be determined from time series of repeated altimeter profiles.
Maps of sea height variability and eddy kinetic energy derived from Geos-3 and Seasat altimetry in some cases represent improvements
over those derived from standard oceanographic observations. Measurement of absolute dynamic height imposes stringent requirements
on geoid and orbit accuracies, although existing models and data have been used to derive surprisingly realistic global circulation
solutions. Further improvement will only be made when advances are made in geoid modeling and precision orbit determination.
In contrast, it appears that use of altimeter data to correct satellite orbits will enable observation of basin-scale sea
level variations of the type associated with climatic phenomena. 相似文献
17.
海底地形对开展海洋科学调查和研究十分重要。以多波束为主的回声测深技术测量成本高且效率低,几十年来仅实现了全球约20%的海床测绘。对于空白区（特别是深海区域）,可以借助重力异常和重力垂直梯度异常进行回归分析反演得到,但该方法得到的比例因子鲁棒性不强。为了解决这一问题,同时考虑到两种重力数据在表征海底地形长短波长的不同优势,本文结合滑动窗口赋权和稳健回归分析来反演海底地形。在太平洋皇帝山海域（35°～45°N,165°～175°E）的实验结果表明:在船测检核点处,本文构建模型的标准差为61.02 m,相比于单一重力数据反演模型,精度分别提高了14.92%（重力异常）和2.08%（重力垂直梯度异常）,能较好地反映皇帝海山链的地形走势。 相似文献
18.
Maaria Nordman Jaakko Kuokkanen Mirjam Bilker-Koivula Hannu Koivula Pasi Häkli Sonja Lahtinen 《Marine Geodesy》2013,36(5):457-476
AbstractWe studied geoid validation using ship-borne global navigation satellite systems (GNSS) on the Baltic Sea. We obtained geoid heights by combining GNSS–inertial measurement unit observations, tide gauge data, and a physical sea model. We used two different geoid models available for the area. The ship route was divided into lines and the lines were processed separately. The GNSS results were reduced to the sea surface using attitude and draft parameters available from the vessel during the campaign. For these lines, the residual errors between ellipsoidal height versus geoid height and absolute dynamic topography varied between 0 and 15?cm, grand mean being 2?cm. The mean standard deviations of the original time series were approximately 11?cm and reduced to below 5?cm for the time series filtered with 10?min moving average. We showed that it is possible to recover geoid heights from the GNSS observations at sea and validate existing geoid models in a well-controlled area. 相似文献