共查询到20条相似文献，搜索用时 421 毫秒
1.
Introduction Analyzing tectonic stress field based on focal mechanism data is an important way to the study tectonic evolvement of lithosphere and associated dynamic process. Such studies growrapidly in China and abroad (Zoback, 1992; Plenefisch, Bonjer, 1997; XU, 1985; CUI, XIE, 1999). At present most of the studies focus on the inversion of focal mechanism data for the direction and relative magnitude of stress tensor, and few on absolute stress. Using focal mechanism and fault scratch,… 相似文献
2.
2008年汶川地震后,为查明北京地区现今地应力状态、评价断裂稳定性,相继在北京地区开展了5个深孔（600~1000 m）的水压致裂法地应力测量,并在适宜深度安装了地应力相对变化监测探头,建立了地应力变化监测台站.本文首先利用实测地应力数据分析了北京地区地壳浅表层应力状态,结果表明：（1）北京地区千米深度内,最大、最小水平主应力随深度增加梯度系数分别为0.0328和0.0221,侧压系数Kav和KHv值,最大、最小水平主应力之比KHh值与国内外已有认识基本一致,而水平向剪应力相对强度参数μm值较低;（2）北京地区最大水平主应力优势方向为近EW向,与华北地区构造应力场方向基本一致,同时受区内断裂活动等影响,存在与区域主应力方向偏差的局部应力场;（3）实测数据揭示的应力结构显示,北京地区地壳浅表层最大主应力（σ1）总体为最大水平主应力（σH）,受区域构造演化以及测点附近断裂的影响,中间主应力（σ2）与最小主应力（σ3）所对应的实测地应力存在变化,但总体来讲,实测地应力数据揭示的应力结构与北京地区主要断裂性质基本相吻合.其次,基于实测应力数据,采用库仑摩擦滑动准则,结合拜尔定律,并取摩擦系数为0.2~1.0,初步评价了北京地区主要断裂稳定性,结果显示：（1）在摩擦系数取0.6~1.0条件下,北京地区现今应力状态尚未达到导致断裂失稳滑动水平,断裂不会出现失稳滑动现象;（2）摩擦系数弱化到0.4时,西峰寺钻孔应力状态满足断裂失稳滑动条件,揭示出八宝山断裂存在失稳滑动可能性,而夏垫-马坊断裂和黄庄-高丽营断裂附近测点应力状态将趋近满足断裂失稳滑动条件,表明这两条断裂有趋向失稳滑动可能性;（3）只有当摩擦系数弱化到0.2时,北京地区主要断裂才可能在现今应力状态出现断裂失稳滑动.本文的认识对北京地区乃至华北地区构造应力场、地震地质研究有重要参考意义. 相似文献
3.
ANALYSIS OF THE CONFIDENCE INTERVAL OF THE COMPOSITE FAULT PLANE SOLUTION OBTAINED FROM THE GRID SEARCH METHOD: AN EXAMPLE OF SOUTHERN JIANGXI PROVINCE 
下载免费PDF全文
下载免费PDF全文 In order to quantitatively analyze the reliability of the composite fault plane solution of small earthquakes, the Bootstrap sampling technique is introduced into the grid search method, and the ideas and methods for calculating the confidence interval from the grid search method are proposed initially. There are two sample sets that can represent the characteristics of the composite fault plane solution. One sample set is the optional solutions obtained by the grid search method and the other is obtained by the Bootstrap sampling technique. Then, we calculate the confidence intervals of the two sample sets (P, B and T axis). The research results of tectonic stress field in southern Jiangxi Province are relatively few. In view of such situation, we use the focal mechanism solutions of small earthquakes to calculate and analyze the composite fault plane solution and the confidence interval. This study shows that the confidence interval of the principal stress axis can be obtained well by both of the sample methods. The reliability of the results and the confidence range of the principal stress axis can be better represented by the confidence intervals. The middle principal stress in southern Jiangxi Province is nearly vertical, and the maximum and minimum principal stresses are nearly horizontal. The direction of maximum principal stress is NWW-SEE and that of the minimum principal stress is NNE-SSW. And, the area is in a strike-slip stress regime. The results are consistent with previous studies, and the stress directions obtained by previous researchers are within the confidence interval calculated by this paper. 相似文献
4.
Introduction The southeast coastal margin of Chinese mainland is important to understand the mutual movement, matter exchange and energy transfer between ocean and land lithospheres, as well as their effects. The coastal area in Fujian Province is advanced in economy development but it has frequent earthquakes, or even strong earthquakes. Therefore, the current study on in-situ stress state measurement is of great significance for studying continental dynamics, marginal sea dy- namics, seismo… 相似文献
5.
在距唐山地震震源约百公里的大港油田,以水压致裂法,在深度1000——4000米之间,测定了69次地应力值,对比了1973——1980年大地震前后八年内的应力值变化.在主震前,构造应力场出现明显变化:(1)水平应力梯度降低,即在最大与最小水平主应力方向呈现应力松弛;(2)水平应力与深度的相关系数降低,即构造应力场受到扰动;(3)断层滑动系数增高,断层出现无震蠕动.此外,结合地质构造与应力测量结果,对唐山地震发生过程中的一些异常现象,如无震蠕动、地下水位变化、浅层和外围地区的应力松弛,以及应力沿断层面向深层和闭锁区的转移等,进行了分析和讨论. 相似文献
6.
2008年和2009年, 通过和新加坡宜康地质技术有限责任公司合作, 在新加坡18个浅钻孔中进行了水压致裂地应力测量. 通过测量获得了新加坡地壳浅部的现今应力状态, 为新加坡拟建地下管缆隧道设计施工提供了地应力依据, 也为世界应力环境数据库提供了参考. 测试结果表明, 在38.00~56.95 m深度域内最大水平主应力σh值为3.45~9.64 MPa, 最小水平主应力σh为2.49~6.28 MPa. 水平主应力和用上覆岩层重量计算的垂直应力σv之间的关系为σh>σh>σv,最大、最小水平主应力平均值分别是垂直应力平均值的5.13倍和3.23倍, 表明新加坡应力场以水平应力为主导. 初步分析认为, 新加坡陆域浅部构造应力场的量值大致呈南、北两端偏低, 中间高的态势, 在北端最大与最小水平主应力值都小于它们各自的平均值, 而南端则与平均值相当. 最大水平主应力优势方向为NE—NEE向, 该方向与前人在其邻区获得的构造应力场方向和由震源机制解反映的主压应力方向较为一致. 新加坡现今构造应力场状态与印度板块、澳大利亚板块、菲律宾板块与欧亚板块的汇聚作用有着密切的联系. 根据库仑摩擦滑动准则, 断层面摩擦系数取0.6~1.0, 分析了研究区内断层产生摩擦滑动的可能性. 相似文献
7.
基于国家测震台网数据中心提供的波形资料, 采用gCAP方法反演2020年5月18日云南巧家M5.0地震及研究区域51次地震震源机制解, 并收集研究区域震源机制解50个。 采用网格搜索法反演区域构造应力场, 并对研究区域采用不同划分进行应力场反演。 获得以下结论: ① 主震震源机制解节面Ⅰ的走向、 倾角和滑动角分别为175°、 67°和-19°, 节面Ⅱ的走向、 倾角和滑动角分别为273°、 73°和-156°, 矩震级为4.97, 矩心深度为8.8 km。 表明主震属于兼具逆冲分量的走滑型地震; ② 震后区域应力场主压应力轴方位为NWW, 倾角接近水平, 主张应力轴方位为NNE, 倾角接近水平, 属于走滑型应力状态, 与周边地质构造运动状态相吻合; ③ 对研究区域采用不同划分所得应力场结果相差不大, 表明该区域应力场比较稳定, 受深大断裂带和震源机制解类型影响较小。 相似文献
8.
Reservoir induced earthquakes (RIE) are caused by impoundment of reservoir,with the characteristics of small magnitude and shallow focal depth,but they can also lead to not only economic loss,but also many serious secondary disasters,such as dam destruction,landslide,producing greater damages far more than the damages directly produced by earthquakes.So study on RIE is quite significant in the field of dam construction,thus more attentions should be paid to RIE.There are many factors to induce reservoir earthquakes,such as geological condition,rock mass mechanical index,state of crustal stress,pore pressure distribution,all of which are extremely difficult to measure due to the presence of many randomness;even if applying most advanced methods to measure them,the values fluctuate in great range,without a certain value in time and space.The great variety of these parameters gives rise to troubles to analyze RIE by deterministic approaches.How to handle the randomness of these factors has become vital problem in the field of RIE research.In this study,based on probability theory,and taking the main influence factors as stochastic variables,a new method to analyze probability of RIE was proposed by applying reliability theory.Firstly,the factors inducing reservoir earthquakes were analyzed,of which pore pressure in fault caused by water impounding of reservoir plays a vital role in triggering earthquakes.Then,taking these factors,including attitude,friction coefficient,cohesion of fault plane,stress state of fault plane and pore pressure in fault,as stochastic variables,performance function of triggering earthquakes was established by applying Coulomb stress on the fault plane,and reliability theory was used to analyze probability of earthquake induced by main factors.A special case analysis showed that:(1) The probability of induced earthquakes dramatically increases as pore pressure in fault increases;under the condition of equal pore pressure at triggering earthquakes area,probability of induced earthquakes obviously rises with enlarging of variation of pore pressure;(2) those faults with strike approximately parallel to horizontal maximum principal stress direction or with steep dip angle about more than 60° are prone to inducing earthquake;(3) as horizontal minimum principal stress increases,which has greater effect on induced earthquakes than horizontal maximum principal stress,probability of induced earthquakes becomes lower and fault keeps in more stable condition;(4) probability of induced earthquakes gradually decreases with the increase of friction coefficient and cohesion of fault plane;However,the effect of friction coefficient on induced earthquakes is much greater than the cohesion of fault plane. 相似文献
9.
世界应力图(WSM，World Stress Map)计划的应力指标，目前已累积数据共计10 920个，这些应力指标代表了该地区最大水平主应力的实际观测方向；与此同时，可以假定全球各个板块的绝对运动方向表征了相应各板块的最大水平主应力方向的长波分量．根据应力场的叠加原理，得到由该地区局部构造运动等因素贡献的短波分量的相对大小和方向．将全球划分成2.52.5的基本单元，对每个单元的WSM数据进行加权统计分析，得到其平均应力观测取向，利用HS2-NUVEL1全球绝对板块运动模型计算应力场的长波分量；平均观测应力取向和长波分量取向之间的夹角，决定了相应短波分量相对于观测应力场的大小及其取向的范围，并反映了特定研究地区局部应力场对总应力场的贡献程度．本文的计算结果表明，全球板块的绝大部分地区及各板块的平均效果，长波分量与短波分量对观测应力场的贡献程度相当．对于某些大陆板块内部，局部构造活动对观测应力场的贡献起到重要作用，因而控制着地震的孕育与发生． 相似文献
10.
岩芯非弹性应变恢复法是近年来发展起来的比较经济有效的深部地应力测量方法,汶川5.12地震后,我国大陆首次将该方法应用于汶川地震断裂带科学钻的地应力测量.本文简述了该方法的原理、计算方法和汶川地震科学钻一号孔的典型结果.给出了一号孔在所测深度之处的三个主应力的大小和方向.三个主应力中,最大主应力和中间主应力近于水平,最小主应力近于直立.最大主应力方向为北西.在746 m深度,三个主应力的大小为25.2 MPa,21.5 MPa,18.5 MPa.这种应力状态可使龙门山断层产生逆冲兼右行走滑运动,与汶川5.12地震的断层运动一致.该方法得到的结果与震源机制解及其他地应力测量方法得到的结果吻合.测量结果表明,非弹性应变恢复法具有较大的实用价值.特别是在较大深度的钻孔和地层较破碎的复杂地质条件下,应力解除法、水压致裂法等难以实施时,此方法仍有可能获得较可靠的地应力数据,适应性更强. 相似文献
11.
Based on 141 data of in-situ stress orientations data of breakouts, stress reliefs and hydraulic fracture tests, and some
data of stress magnitudes from oil-well hydrofracturing operations, this paper discusses in-situ stress regime and the tectonic
stress provinces in the China’s Sea and adjacent areas. Furthermore, the origin of tectonic stress field is expounded.
The research results show that the tectonic stress in China’s Sea region can be divided into some stress provinces which are
the extension of the Northern China and Southern China stress provinces toward the eastern sea area. The tectonic stress field
in the Bohai and Huanghai and their neighbouring regions is controlled by a ENE-WSW compression, where the faulting types
are mainly strike-slip. However, the stress in the East and South China’s sea region and the Taiwan Straits is dominated by
the WNW-NW-NNW compressions, that is to say that the orientations of the maximum horizontal stress spread radially from the
central mainland toward southeastern sea areas. The principal stress directions become more and more steady and uniform as
depth increases. In the North China and nearby areas, the types of faulting are primarily strike-slip. In Southern China and
adjacent sea areas, there is a transition layer at 1,700M depth, the faultings principally show reverse faults above that
depth and strike-slip below it. Furthermore the origin of the tectonic stress field in this region may primarily come from
the composite action of the Pacific, the Philippine sea and the India-Australian plates.
The Chinese version of this paper appeared in the Chinese edition ofActa Seismologica Sinica,14, 17–28, 1992. 相似文献
12.
本文在对龙滩库区2006年9月30日至2013年5月26日发生的3682次地震进行精定位的基础上,利用FOCMEC方法和改进的格点尝试法反演了ML2.0以上地震震源机制及区域构造应力场,并综合龙滩库区地层岩性、断裂构造和渗透条件等资料,探讨了地震活动类型与库区蓄水过程的关系,获得以下认识:(1)龙滩水库蓄水后的地震活动主要丛集在罗妥、八茂、拉浪、坝首和布柳河5个深水区,地震类型以逆断为主,正断和走滑也占有一定比例.蓄水初期,库区地震类型呈现多样性,蓄水约4年3个月后,地震主要发生在浅部地层中,并大多为逆断型地震.(2)5个地震丛构造应力场最大主应力方向以NW—SE为主,倾角均较小,中等和最小主应力分布较凌乱,在此构造应力环境中,龙滩库区主要断裂整体上呈现走滑运动的性质,局部伴生不同程度的逆倾滑或正倾滑运动分量.(3)库区深、浅部地震活动水平和地震性质之所以会随蓄水过程发生变化,可能与深、浅部构造应力环境、岩体力学性质和渗透性能的差异有关. 相似文献
13.
受印度板块向欧亚板块持续北东向挤压作用,青藏高原腹地拉萨块体内新构造活动强烈,其地应力特征一直是工程规划建设、地球动力学和地壳稳定性研究的重要内容.2014至2015年,沿雅鲁藏布江断裂带,分别在西藏林芝县(LZ)、朗县(LX)和乃东县(ND)开展了水压致裂原地应力测量工作.本文通过测试结果分析,获得了拉萨块体现今地壳浅表层的应力状态及分布特征.LX及ND测点应力强度均高于LZ测点,且应力结构均为逆断型,表现为S_HS_hS_v,水平应力作用占主导.LZ测点在测试深度内揭穿了断裂,且应力结构不够明确.三个测点的应力状态显示出拉萨块体现今地壳强度处于破裂临界状态,结合各测点所处构造环境,应力的持续累积可能会打破这种平衡导致断裂活动.主应力比值K_(Hv)=S_H/S_v,K_(av)=(S_H+S_h)/2S_v和K_f=(S_H—S_h)/2也显示出该区强烈的水平构造运动.三测点揭示的最大水平主应力方向集中于近SN(LX)-NNE(LZ及ND)向,与该区背景应力场特征相一致,且与地壳运动场相耦合,反映出该区应力状态主要受控于印度板块北向欧亚大陆持续挤压碰撞的构造背景,同时各测点之间应力状态的差异性也体现了区域构造作用的差异影响. 相似文献
14.
本文以1996年丽江MS7.0地震为例,以地震目录和强震震源模型为输入参数,将力学计算与统计分析相结合,反演计算了1986～1996年间丽江震区2.5°×3.0°空间范围内的地壳应力状态.结果表明,丽江地区应力场最大主应力为近南北向,方位角为355°,最小主应力方位角为241°,二者倾角为近水平,应力形因子为0.398,最大主应力大小约为53 MPa,远小于完整岩石的强度.该方法可获得地壳深部绝对应力大小、有效摩擦系数,反演获得的震区地壳深部应力状态的方向性特征与震源机制解结果基本一致;该研究表明地震活动的空间分布可以为我们提供有关强震孕震的地壳深部应力状态信息.这些结果对了解震区应力场具有理论上和实践上的意义. 相似文献
15.
CHARACTERISTICS OF FOCAL MECHANISMS AND STRESS FIELD IN THE EASTERN BOUNDARY OF SICHUAN-YUNNAN BLOCK AND ITS ADJACENT AREA 下载免费PDF全文
下载免费PDF全文 This study is devoted to a systematic analysis of the stress state of the eastern boundary area of Sichuan-Yunnan block based on focal mechanisms of 319 earthquakes with magnitudes between M3.0 and M6.9, occurring from January 2009 to May 2018. We firstly determined the mechanism solutions of 234 earthquakes by the CAP method, using the broadband waveforms recorded by Chinese regional permanent networks, and collected 85 centroid moment tensor solutions from the GCMT. Then we investigated the regional stress regime through a damp linear inversion. Our results show that:1)the focal mechanisms of moderate earthquakes are regionally specific with three principal types of focal mechanisms:the strike-slip faulting type, the thrust faulting type and the normal faulting type. The strike-slip faulting type is significant in the eastern boundary area of Sichuan-Yunnan block along the Xianshuihe-Xiaojiang Fault, the Daliangshan Fault, and the Zhaotong-Lianfeng Fault. The thrust faulting type and the combined thrust/strike-slip faulting type are significant along the Mabian-Yanjin Fault, Ebian-Yanfeng Fault and the eastern section of Lianfeng Fault; 2)The most robust feature of the regional stress regime is that, the azimuth of principal compressive stress axis rotates clockwise from NWW to NW along the eastern boundary of Sichuan-Yunnan Block, and the clockwise rotation angle is about 50 degrees. Meanwhile, the angels between the principal compressive axis and the trend of eastern boundary of Sichuan-Yunnan Block remain unchanged, which implies a stable coefficient of fault friction in the eastern boundary fault zone of Sichuan-Yunnan Block. The movement of the upper crust in the southeastern Tibetan plateau is a relatively rigid clockwise rotation. On the whole, the Xianshuihe-Xiaojiang Fault is a small arc on the earth, and its Euler pole axis is at(21°N, 88°E). The Daliangshan Fault is surrounded by the Anninghe-Zemuhe Fault, which formed a closed diamond shape. When the Sichuan-Yunnan block rotates clockwise, the Daliangshan Fault locates in the outer of the arc, while the Anninghe-Zemuhe Fault is in the inward of the arc, and from the mechanical point of view, left-lateral sliding movement is more likely to occur on the Daliangshan Fault. Our results can be the evidence for the study on the "cut-off" function of the Daliangshan Fault based on the stress field background; 3)The regional stress regime of the eastern boundary faults zone of the Sichuan-Yunnan Block is the same as the south section of the Dalianshan Fault, and the focal mechanism results also reveal that the Dalianshan Fault is keeping left-lateral strike-slip. There may be the same tectonic stress field that controls the earthquake activities in the southern section of Daliangshan Fault and Zhaotong-Lianfeng Fault. The regional stress regime of Zhaodong-Lianfeng Fault is also the same with the Sichuan-Yunnan Block, which implies that the control effect of the SE movement of the Sichuan-Yunnan block may extend to Weining. 相似文献
16.
本文研究斜俯冲板块边界由俯冲的逆掩断层和平行于火山弧的走滑断层所切割出的岩石层窄条的宏观力学状态．分析计算表明，当断层强度小而构造压应力大时，海沟处板块俯冲形成的逆掩断层地震滑动方向与斜收敛板块运动方向将不一致，震源机制反映的主压应力和断层错动方向变得近乎垂直于海沟；板块间的强耦合和大陆板块边缘软弱带的存在为窄条滑动提供了有利条件．给定俯冲倾角和震源机制滑动角的观测值，可以计算逆掩和走滑断层上的有效摩擦系数．计算结果表明，两种断层上的有效摩擦系数一般都不大于０．２，反映或存在着高孔隙水压，或存在断层泥之类弱物质，或两者兼而有之． 相似文献
17.
Analysis of induced seismicity for stress field determination and pore pressure mapping 总被引：1，自引：0，他引：1
The focal mechanisms of some one hundred microseismic events induced by various water injections have been determined. Within the same depth interval, numerous stress measurements have been conducted with the HTPF method. When inverted simultaneously, the HTPF data and the focal plane solutions help determine the complete stress field in a fairly large volume of rock (about 15×106 m3). These results demonstrate that hydraulically conductive fault zones are associated with local stress heterogeneities. Some of these stress heterogeneities correspond to local stress concentrations with principal stress magnitudes much larger than those of the regional stress field. They preclude the determination of the regional stress field from the sole inversion of focal mechanisms. In addition to determining the regional stress field, the integrated inversion of focal mechanisms and HTPF data help identify the fault plane for each for each of the focal mechanisms. These slip motions have been demonstrated to be consistent with Terzaghi's effective stress principle and a Coulomb friction law with a friction coefficient ranging from 0.65 to 0.9. This has been used for mapping the pore pressure in the rock mass. This mapping shows that induced seismicity does not outline zones of high flow rate but only zones of high pore pressure. For one fault zone where no significant flow has been observed, the local pore pressure has been found to be larger than the regional minimum principal stress but no hydraulic fracturing has been detected there. 相似文献
18.
IntroductionSouthwest Yunnan region is located in the southeastern margin of Qinghai-Tibet Plateau, bordering on the Sichuan-Yunnan rhomboidal block in the east and on the northeast corner of Indian Plate in the northwest. It is one of the regions of intense tectonic activities and frequent strong earthquakes in China continent. To study the features of modern tectonic stress field of this region is of significance for revealing the evolution mechanisms of Tibetan Plateau as well as for un… 相似文献
19.
SUN DongSheng LIN WeiRen CUI JunWen WANG HongCai CHEN QunCe MA YinSheng WANG LianJie 《中国科学:地球科学(英文版)》2014,57(6):1212-1220
In situ stress state becomes more and more significant with in-depth research on geodynamics and energy development.However,there has not been an economic and effective method developed to determine deep three-dimensional in situ stress.The Anelastic Strain Recovery(ASR)method is a newly developed technique that can determine three-dimensional in situ stresses.After the 12 May 2008 Ms8.0 Wenchuan earthquake,the ASR method was used for the first time in mainland China to measure the in situ stresses in the WFSD scientific boreholes in Sichuan Province,China.In this paper,the basic procedure of the ASR method is introduced in detail and the compliances of ASR for boring cores are investigated.The results show that the maximum principal stress direction was NW64°at a measured depth(MD)of 1173 m(vertical depth 1151 m)in WFSD-1.The ratio of shear mode to the volume mode compliance of ASR was 2.9.And the three principal stresses at 1173 m MD in WFSD-1are 43,28 and 25 MPa.Combined with stress measurement results determined using other in situ measurement methods along the Longmenshan fault zone,the directions of the maximum horizontal principal stress changes from E-W to NEE-SWW to NWW-SEE when moving from NE to SW along the Longmenshan fault zone.This change is in agreement with the stress regime of the Longmenshan fault zone of the Wenchuan Earthquake,which supports a stress regime consisting predominantly of thrusts in the southwest and strike-slip in the northeast. 相似文献
20.
通过对构造变形、构造空间展布关系、断面产状变化以及构造应力场等的综合分析研究认为,阿尔金北缘活动断裂带在第四纪内的运动方式经历了由挤压逆掩为主（早更新世—中更新世初期）到左旋走滑兼具挤压逆冲（中更新世中、晚期）直至纯左旋走滑运动（晚更新世—现今）的逐渐转变过程．作用于这种转变,研究区内区域构造应力场的演变大致可以划分为三期,其主压应力轴方向由老至新依次为近南北向、北北东向和北东向．构造应力场和断裂带运动方式的这些变化主要是由于印度板块持续向北推挤导致青藏高原内部次级块体向东滑动、岩石圈物质向东流展而造成的． 相似文献