共查询到20条相似文献，搜索用时 218 毫秒
1.
台湾浅滩海底沙波精细特征、分类与分布规律 总被引：2，自引：2，他引：0
迄今由于缺乏高精度的实测水深数据,对台湾浅滩沙波的精细结构缺乏详细的阐述。本文基于多波束实测资料研究台湾浅滩沙波形态的精细特征及其分布规律。多波束探测结果显示:研究区沙波的平均波高达到13.5m,沙波波峰处水深为20.42m,沙波平均波高约为水深的2/3,沙波的波长大多数处于500~700m之间。研究区内主要发育3种类型的沙波,即摆线型沙波、余弦型沙波和双峰型沙波。研究区西部主要发育双峰型沙波,中部则主要发育余弦型和摆线型沙波,而东部主要发育摆线型沙波,整个区域以摆线型沙波为主。海平面波动、台湾海峡复杂的水动力条件以及台湾岛丰富的山溪河流携带的大量沉积物进入海峡,对浅滩区的沙波具有强烈的改造作用。 相似文献
2.
台湾浅滩沉积物和沉溺海滩岩的研究 总被引：2，自引：0，他引：2
台湾浅滩位于南海北部大陆架之东部,面积约8800km~2,由众多的沙丘组成,水深一般为20—40m,呈北东向展布(图1)。近半个世纪以来,中外许多学者进行了研究,认为这套砂质沉积是冰期残留沉积物。1979年,中国科学院南海海洋研究所在台湾浅滩进行调查,本文对这次调查中采集的沉积物样品和沉溺海滩岩作了研究,并对古地理、古气候及海平面变化进行了讨论。 相似文献
3.
4.
对2006年8月所获台湾浅滩的底质、水深、多层位流速、流向以及CTD观测数据进行了分析,探讨了台湾浅滩大型沙波区水流的时空分布特征、沉积物输运过程及影响因素,结果表明,台湾浅滩动力作用较强,底质为粗砂,其上发育的沙波波长为325~822 m,波高为14.4~20.3 m,较接近由前人总结的沙波波高、波长的关系式计算出的波高和波长。沙波波峰、波谷、迎水面和背水面流速以12.5 h为周期沿顺时针方向旋转;底部最大流速出现在半日潮周期的同一时段,对应的方向均为偏南方向,且沙波迎水面的流速大于背水面的。在两个半日潮过程中研究区域的沉积物输入量大于输出量,处于淤积状态。在潮流作用下沉积物输运量较少,沙波脊线移动较小,而台湾浅滩有较大规模的沙波运动,故认为改造沙波的主要作用力应该是风暴流。在观测的断面中涨潮推移质输运量大于落潮的,且第一个半日潮涨落潮的输运能力均较第二个半日潮的大,这可能与潮流的流速-时间不对称特征及潮能变化形式有关。 相似文献
5.
基于FVCOM海洋数值模式,采用非结构三角形网格较好地刻画了台湾海峡复杂的岸线边界及海底地形,建立了台湾海峡的三维潮汐潮流数值模型.模拟结果同长期观测资料符合良好,较好地反映出台湾海峡内潮汐、潮流运动的变化状况和分布特征,利用T_tide工具包进行水位潮流调和分析给出了M2、S2、K1、O1四个主要分潮的同潮图、表层潮流椭圆分布.分析表明,M2分潮由台湾岛南北两端传入台湾海峡,两支潮波在澎湖—台湾浅滩南缘相遇,呈NE—SW向倾斜,振幅最大值为2.45m,出现在福建省湄洲湾、兴化湾一带.K1分潮潮波由东北向西南传入,并向南海传播,传播方向上右侧振幅较左侧大0.05m.台湾海峡存在一条分潮潮流椭圆率为0的分隔线,该分隔线大致呈NE—SW走向,分隔线上半部分潮流椭圆旋转方向为逆时针方向,下半部分为顺时针方向.四个主要分潮潮流椭圆长轴基本呈NE—SW走向,但在台湾浅滩表层潮流椭圆长轴方向为NW—SE向,澎湖水道呈N—S向.台湾浅滩处四个分潮的潮流椭圆均较大,对应的潮流也强,可能受当地水深较浅的影响. 相似文献
6.
7.
利用 1935年、1962年、2005年和 2010年 4个年份的水深地形资料,基于 GI S 技术采用数字化定量冲淤计算和
10m 特征等深线叠加分析,结合实测水文泥沙资料,探讨了象山港口门浅滩冲淤动态趋势。结果表明： 1935-2010年的 75
年间,象山港口门浅滩经历了略微冲刷或冲淤接近平衡、轻微淤积和缓慢淤积的动态调整过程,年均淤积速率 1. 41 cm/ a;东
北和西南两翼边界 10 m 特征等深线分别以年均速率 2. 0 m/ a外移和 0. 2 m/ a内移。近几年来,受所在陆域和梅山岛局部岸段
较大规模围涂造地岸线外移影响,该浅滩淤积速率较明显增加。 相似文献
8.
2007年7月,对台湾浅滩43个站位进行了表层底质采样,在室内用Mastersizer 2000型激光粒度仪获得了沉积物的粒径分布,并用矩法计算其粒径参数.研究区内沉积物类型多为砂和含砾砂,平均粒径集中于0Φ到3Φ之间.福建—广东沿岸海域一带沉积略细,沿岸带外侧的浅槽,以及台湾浅滩东北边坡与南边坡沉积略粗.用粒径趋势分析计算结果显示,台湾浅滩东北方向与偏西方向的沉积物均向浅滩核部汇聚;而浅滩核心区的粒度参数比较接近,沉积物输运趋势弱化. 相似文献
9.
台湾浅滩中粗砂的时代与成因 总被引：6，自引：0，他引：6
本文根据台湾浅滩柱状沉积物的粒度、矿物、化学、微体古生物、~(14)C测年等项目的分析,讨论了该浅滩中粗砂的形成时代及其成因。结果表明,台湾浅滩中粗砂是20ka,B.P.前的异地物质,在10k～20ka,B.P.期间由单向海流搬运而来堆积形成的,当时的台湾浅滩处于浅海环境,其物质可能主要来自韩江河口;浅滩边缘区还可能受沿岸流影响,接受来自九龙江的物质。 相似文献
10.
11.
Chandralata Raghukumar G. Sheelu P. A. Loka Bharathi Shanta Nair C. Mohandass 《Marine Georesources & Geotechnology》2001,19(1):1-16
In order to assess the impact of deep-sea mining on the in situ benthic life, we measured the microbial standing stock and concentration of organic nutrients in the deep-sea sediments of the Central Indian Ocean Basin in the Indian pioneer area. Sediments were collected using box core and grab samples during September 1996. The total bacterial numbers ranged from 10 10 -10 11 cells per g -1 dry weight sediment. There was a marginal decrease in the number of bacteria from surface to 30 cm depth, though the subsurface section registered a higher number than did the surface. The highest numbers were encountered at depths of 4-8 cm. The retrievable number of bacteria were two orders less in comparison with the direct total counts of bacteria. An almost homogeneous distribution of bacteria, total organic carbon, living biomass, and lipids throughout the depth of cores indicates active microbial and benthic processes in the deep sea sediments. On the other hand, a uniform distribution of total counts of bacteria, carbohydrates, and total organic carbon in all the cores indicates their stable nature and suggests that they can serve as useful parameters for long-term monitoring of the area after the benthic disturbance. Further studies on temporal variability in this region would not only verify the observed norms of distribution of these variables but would also help to understand restabilization processes after the simulated benthic disturbance. 相似文献
12.
Derek V. Ellis 《Marine Georesources & Geotechnology》2001,19(1):51-63
This article reviews information recently available from existing marine and coastal mining for responses to environmental issues affecting marine mining at different depths. It is particularly but not exclusively concerned with those issues affecting seabed biodiversity impact and recovery. Much information has been gathered in the past 10 years from shallow mining operations for construction aggregate, diamonds, and gold, from coastal mines discharging tailings to shallow and deep water, and from experimental deep mining tests. The responses to issues identified are summarized in a series of eight tables intended to facilitate site-specific consideration. Since impacts can spread widely in the surface mixing layer SML, and can affect the biologically productive euphotic zone, the main issues considered arise from the depth of mining relative to the SML of the sea. Where mining is below the SML, the issue is whether it is environmentally better to bring the extraction products to the surface vessel for processing (and waste discharge), or to process the extraction products as much as possible on the seabed. Responses to the issues need to be sitespecific, and dependent on adequate preoperational environmental impact and recovery prediction. For deep tailings disposal from a surface vessel, there are four important environmental unknowns: (1) the possible growth of "marine snow" (bacterial flocs) utilizing the enormous quantities of fine tailings particles (hundreds or thousands of metric tons per day) as nuclei for growth, (2) the possibility that local keystone plankton and nekton species may migrate diurnally down to and beyond the depth of deep discharge and hence be subjected to tailings impact at depth, (3) the burrow-up capability of deep benthos and their ability to survive high rates of tailings deposition, and (4) the pattern and rate of dispersion of a tailings density current through the deep water column from discharge point to seabed. Actions to obtain relevant information in general and site-specifically are suggested. 相似文献
13.
G. Parthiban 《Marine Georesources & Geotechnology》2000,18(3):223-235
Particle fluxes were measured 7 m above the sea bottom during the predisturbance, disturbance, and postdisturbance periods by using time series sediment traps attached to seven deep-sea moorings deployed in the INDEX experiment site in the Central Indian Basin. The predisturbance particle fluxes varied between 22.3 to 55.1 mg m -2 day -1 . Increased and variable particle fluxes were recorded by the sediment traps during the disturbance period. The increase observed was 0.5 to 4 times more than the background predisturbance fluxes. The increases in particle fluxes (~4 times) recorded by the sediment trap located in the southwestern direction (DMS-1) were the greatest, which could be the result of preferential movement of resuspended particles generated during the deep-sea benthic disturbance along the general current direction prevailing in this area during the experimental period. Also, the traps located closer to the disturbance area recorded greater fluxes than did the traps far away, across the Deep Sea Sediment Resuspension System path. This variability in recorded particle fluxes by the traps around the disturbance area clearly indicates that physical characteristics such as grain size and density of the resuspended particles produced during the disturbance had an important effect on particle movement. The postdisturbance measurements during ~5 days showed a reduction in particle fluxes of ~50%, indicating rapid particle settlement. 相似文献
14.
Arne Schnack-Friedrichsen Angela M. Davis Jim D. Bennell Dei G. Huws 《Marine Georesources & Geotechnology》2001,19(4):221-243
The interdependence between the seismo-acoustic properties of a marine sediment and its geotechnical/physical parameters has been known for many years, and it has been postulated that this should allow the extraction of geotechnical information from seismic data. Though in the literature many correlations have been published for the surficial layer, there is a lack of information for greater sediment depths. In this article, a desktop study on a synthetic seafloor model illustrates how the application of published near-surface prediction equations to subsurface sediments (up to several tens of meters burial depth) can lead to spurious predictions. To test this further, acoustic and geotechnical properties were measured on a number of sediment core samples, some of which were subjected to loading in acoustically-equipped consolidation cells (oedometers) to simulate greater burial depth conditions. For low effective pressures (representing small burial depths extending to around 10 meters subsurface), the general applicability of established relationships was confirmed: the prediction of porosity, bulk density, and mean grain size from acoustic velocity and impedance appears generally possible for the investigated sedimentary environments. As effective pressure increases through, the observed relationships deviate more and more from the established ones for the near-surface area. For the samples tested in this study, in some instances increasing pressure even resulted in decreasing velocities. There are several possible explanations for this abnormal behavior, including the presence of gas, overconsolidation, or bimodal grain size distribution. The results indicate that an appropriate depth correction must be introduced into the published prediction equations in order to obtain reliable estimates of physical sediment properties for greater subsurface depths. 相似文献
15.
海上大直径钢管桩打桩过程中,桩周土体受到强烈扰动而发生强度弱化,掌握桩周土体强度弱化规律对于准确预测打桩过程、保证工程安全具有重要意义。为研究土体强度弱化规律,开展了环剪试验模拟打桩对桩周土体的扰动,测试土体强度随剪切速率的变化规律,建立了描述土体强度弱化规律的拟合公式,引入到打桩分析软件中。研究结果表明：土体的强度折减程度不仅与土体本身的性质有关还受到土体的埋深和剪切速率的影响,埋深越深土体强度折减程度越低,剪切速率越高土体强度折减越高,在打桩分析中可采用这里推荐的线性折减方法来模拟不同深度处土体强度的折减规律。 相似文献
16.
Geoacoustic Inversion via Genetic Algorithm and Its Application to Manganese Sediment Identification
An acoustic inversion method using a wide-band signal and two near field receivers is proposed and applied to multiple layered seabed models including a manganese sediment. The inversion problem can be formulated into a probabilistic model comprised of signals, a forward model, and additive noise. The forward model simulates wide-band signals, such as chirp signals, and is chosen to be the source-waveletconvolution plane wave modeling method. The wavelet matching technique, using weighted least-squares fitting, estimates the sediment sound-speed and thickness on which determination of the possible numerical ranges for a priori uniform distribution is based. The genetic algorithm is applied to a global optimization problem to find a maximum a posteriori solution for determined a priori search space. Here the object function is defined by an L 2 norm of the difference between measured and modeled signals. Not only the marginal pdf but also its statistics are calculated by numerical evaluation of integrals using the samples selected during importance sampling process of the genetic algorithm. 相似文献
17.
The advanced piston corer (APC) has been used by the Ocean Drilling Program since 1985 for recovering soft sediments from the ocean floor. The pullout force measured on extracting the core barrel from the sediment is shown to correlate with the average shear strength of the sediment core measured in the ship's laboratory. A simple rule of thumb is derived relating the shear strength of the sediment to the pullout force. Multiple APC holes at individual sites allow the consistency of the pullout measurements to be assessed. The effects of different operational procedures during APC coring are also explored. Although generally applicable, the correlation between pullout force and laboratory measurements of shear strength breaks down for some APC holes, possibly because of the disturbance of some sediment types during the APC coring process. A better understanding of the physical process of APC coring, and its effect on the properties of the sediment both inside and immediately outside the core barrel, would indicate what confidence can be put on the measurement of pullout force as a way of evaluating the in situ shear strength of deep sea sediments. 相似文献
18.
19.
20.
《海洋学报(英文版)》2014,(11):161-F0003
<正>Acta Oceanologica Sinica(AOS)is a comprehensive academic journal edited by the Editorial Committee of Acta Oceanologica Sinica and is designed to provide a forum for important research papers of the marine scientific community which reflect the information on a worldwide basis.The journal publishes scholarly papers on marine science and technology,including physics,chemistry,biology, 相似文献