共查询到20条相似文献，搜索用时 46 毫秒
1.
Understanding the behavior of colloids in groundwater is critical as some are pathogenic while others may facilitate or inhibit the transport of dissolved contaminants. Colloid behavior in saturated fractured aquifers is governed by the physical and chemical properties of the groundwater-particle-fracture system. The interaction between these properties is nonlinear, and there is a need for a mathematical model describing the relationship between them to advance the mechanistic understanding of colloid transport in fractures and facilitate modeling in fractured environments. This paper coupled genetic programming and linear regression within a multigene genetic programming framework to develop a robust mathematical model describing the relationship between colloid retention in fractures and the physical and chemical parameters that describe the system. The data employed for model development and validation were collected from a series of 75 laboratory-scale colloid tracer experiments conducted under a range of conditions in three laboratory-induced discrete dolomite fractures and their epoxy replicas. The model sufficiently reproduced the observed data with coefficients of determination (R2) of 0.92 and 0.80 for model development and validation, respectively. A cross-validation demonstrated the model generality to 86% of the observed data. A variance-based global sensitivity analysis confirmed that attachment is the primary retention mechanism in the systems employed in this work. The model developed in this study provides a tool describing colloid retention in factures, which furthers the understanding of groundwater-particle-fracture system conditions contributing to the retention of colloids and can aid in the design of groundwater remediation strategies and development of groundwater management plans. 相似文献
2.
《水文科学杂志》2013,58(6):1300-1309
Abstract A unique, large-scale tracer test performed along a 90-km reach of a natural river is presented. This method was crucial for evaluating the impact of a retention reservoir on protected areas of the river downstream, and to assess the threats due to potentially catastrophic releases of toxic substances into that river. The response to the slug injection of a soluble tracer is assumed to imitate the characteristics of a soluble pollutant, so an understanding of how tracers mix and disperse in a stream is essential to understanding the processes of pollution transport. The procedure applied during this experiment consisted of the instantaneous injection of a known quantity of Rhodamine WT into the stream and the determination of the temporal variation in concentration of the tracer at sites as it moved downstream. The results were analysed from the perspective of a transient storage model. Relevant model parameters were evaluated by fitting the computed breakthrough curves to the observed ones on a reach-by-reach basis. 相似文献
3.
The knowledge on particle deposition in streams is mainly based on investigations in mountain streams. No data exist from low‐gradient sand‐bed streams that largely differ in the morphological and hydraulic factors proposed to affect deposition. To identify physical control on particle deposition in low‐gradient streams, we assessed deposition of very fine and ultra fine organic particulate matter in 18 sand‐bed stream reaches. We added particles derived from lake sediment and assessed the mean transport distance SP and the deposition velocity vdep. Additionally, reach hydraulics were estimated by injections of a conservative solute tracer (NaCl). Among the low‐gradient streams, particle deposition kinetics were variable but similar to deposition in mountain streams. SP was solely related to the flow velocity. This relation was confirmed when comprising published data on deposition of fine organic particles. An association between particle deposition and transient storage factors was insignificant. We found significance of the transient storage to SP only for repeated measures within a single reach, when flow velocity and benthic conditions were nearly constant. Measured vdep/vfall ratios were much larger than unity in most reaches. Evidence from this relation suggests that the vertical transport of very fine and ultra fine organic particulate matter through the water column was caused mainly by vertical mixing. Copyright © 2006 John Wiley & Sons, Ltd. 相似文献
4.
M. C. Tom Kuo 《Ground water》2022,60(4):510-517
Few published data are available for two-phase flow in fractures from field studies. All measurements of relative permeability reported in the literature were done in laboratory-scale. The in situ water saturations are normally not known for multiphase flow in natural fractures; therefore, the direct measurements of relative permeability are difficult in field-scale. With the help of a case study before and after the 2008 Mw 5.4 Antung earthquake, groundwater radon was used as a tracer to determine the gas and water saturations in a small naturally fractured aquifer. Well tests were also conducted to estimate aquifer transmissivity before and after the 2008 Antung earthquake. Anomalous declines in both groundwater radon concentration and transmissivity were observed precursory to the 2008 Antung earthquake. Both declines are two precursory phenomena having a common effect of gas bubbles. Using the data from well tests and radon tracer, one data point of water relative permeability can be obtained for in situ fractures. This data point reveals strong phase interference between water and gas bubbles for multiphase flow in natural fractures. Both the data of well tests and radon tracer are essential to gain an improved understanding of mass transfer behavior of groundwater-dissolved gases between water and gas phases. 相似文献
5.
Soil pipe flow tracer experiments: 2. Application of a streamflow transient storage zone model 
下载免费PDF全文
下载免费PDF全文 Soil pipes are important subsurface flow pathways in many soil erosion phenomena. However, limited research has been performed on quantifying and characterizing their flow and transport characteristics. The objectives of this research were to determine the applicability of a streamflow model with transient storage in deriving flow and transport characteristics of soil pipes. Tracer data from pulse inputs were collected in four different soil pipes after a fluorescein dye was injected in the upstream end of each soil pipe network in three branches (west, middle, and east) of a main catchment and a back catchment in Goodwin Creek Experimental Watershed in Mississippi. Multiple sampling stations were positioned along each soil pipe network. The transient storage zone model OTIS‐P was executed inversely to estimate transport parameters by soil pipe reach such as the soil pipe cross‐sectional area (A), soil storage zone cross‐sectional area (As), and exchange rate between the soil pipe and the soil storage zone (αs). Model convergence was achieved, and simulated breakthrough curves of the reaches were in good agreement with actual tracer data for eight of the nine reaches of the three branches of the Main Catchment and five of the seven reaches of the Back Catchment soil pipe. Simulation parameters for the soil pipe networks were similar to the range of values reported for flow and transport characteristics commonly observed in streams. Inversely, estimated soil pipe flow velocities were higher with increased tortuosity, which led to a smaller cross‐sectional areas predicted for the soil pipe flowpaths, while other parameters were not sensitive to tortuosity. In general, application of One‐Dimensional Transport with Inflow and Storage‐P to this unique soil pipe condition suggested larger transient storage (As and αs) compared with most stream systems. This was hypothesized to be because of relatively higher ratio of the wetted perimeter to flow area in the soil pipe, the hydraulic roughness of the soil pipe, potential retention in collapsed portions of the pipe, and interaction with smaller preferential flow systems. Copyright © 2015 John Wiley & Sons, Ltd. 相似文献
6.
A tracer study performed on a 3 km long reach of the Danube River in Austria is presented. Forty artificial stones of three different sizes (intermediate b‐axis: 25 mm, 40 mm, 70 mm) were produced and a coded radio acoustic transmitter was implanted. The measurement system had to be improved to be applicable to large rivers with water depths up to 12 m. The positions of the stones were observed approximately once a week, depending on hydrology, over a period of at least one year by radio‐tracking from a boat, including a 15 year flood event. Transport paths and velocities, as well as the incipient motion of bedload transport, could be monitored for the first time on a large gravel‐bed river. The particle paths were found to be mostly bankline‐parallel, even though the stones passed a 30° river bend. The median of the transverse particle displacement was found to be 4% of the longitudinal displacement. Calculations considering both transverse slope and transverse flow velocities showed transverse transport to be 6·6% of the longitudinal transport indicating that marginal lateral transport is mainly influenced by morphology. A three‐dimensional (3D) numerical model using a stochastic particle tracing approach was validated with the data, indicating that the observed positions are well reproduced by the model. Within the observation period, 74% of all stones passed the reach. With more than 1000 detections, particle transport could be characterized by a mean travel velocity of about 10 m per day (variable for the different grain sizes); single tracer stones were transported up to 1000 m during a single flood event. Size‐selective behaviour could be shown and the incipient motion of the large 70 mm gravel was detected at lower discharges than predicted by commonly used uniform bedload transport formulae. Copyright © 2012 John Wiley & Sons, Ltd. 相似文献
7.
Aggregation processes of fine sediments have rarely been integrated in numerical simulations of cohesive sediment transport in riverine systems. These processes, however, can significantly alter the hydrodynamic characteristics of suspended particulate matter (SPM), modifying the particle settling velocity, which is one of the most important parameters in modelling suspended sediment dynamics. The present paper presents data from field measurements and an approach to integrate particle aggregation in a hydrodynamic sediment transport model. The aggregation term used represents the interaction of multiple sediment classes (fractions) with corresponding multiple deposition behaviour. The k–ε–turbulence model was used to calculate the coefficient of vertical turbulent mixing needed for the two‐dimensional vertical‐plane simulations. The model has been applied to transport and deposition of tracer particles and natural SPM in a lake‐outlet lowland river (Spree River, Germany). The results of simulations were evaluated by comparison with field data obtained for two levels of river discharge. Experimental data for both discharge levels showed that under the prevailing uniform hydraulic conditions along the river reach, the settling velocity distribution did not change significantly downstream, whereas the amount of SPM declined. It was also shown that higher flow velocities (higher fluid shear) resulted in higher proportions of fast settling SPM fractions. We conclude that in accordance with the respective prevailing turbulence structures, typical aggregation mechanisms occur that continuously generate similar distribution patterns, including particles that settle toward the river bed and thus mainly contribute to the observed decline in the total SPM concentration. In order to determine time‐scales of aggregation and related mass fluxes between the settling velocity fractions, results of model simulations were fitted to experimental data for total SPM concentration and of settling velocity frequency distributions. The comparison with simulations for the case of non‐interacting fractions clearly demonstrated the practical significance of particle interaction for a more realistic modelling of cohesive sediment and contaminant transport. Copyright © 2004 John Wiley & Sons, Ltd. 相似文献
8.
Modelling and experimental study of coupled exchange of p,p′‐DDE and colloids in a flume simulated stream–streambed system 下载免费PDF全文
下载免费PDF全文 Stream–subsurface exchange plays a significant role in the fate and transport of contaminants in streams. It has been modelled explicitly by considering fundamental processes such as hydraulic exchange, colloid filtration, and contaminant interactions with streambed sediments and colloids. The models have been successfully applied to simulate the transport of inorganic metals and nutrients. In this study, laboratory experiments were conducted in a recirculating flume to investigate the exchange of a hydrophobic organic contaminant, p,p′‐dichloro‐diphenyl‐dichloroethane (DDE), between a stream and a quartz sand bed. A previously developed process‐based multiphase exchange model was modified by accounting for the p,p′‐DDE kinetic adsorption to and desorption from the bed sediments/colloids and was applied to interpret the experimental results. Model input parameters were obtained by conducting independent small‐scale batch experiments. Results indicate that the immobilization of p,p′‐DDE in the quartz sand bed can occur under representative natural stream conditions. The observed p,p′‐DDE exchange was successfully simulated by the process‐based model. The model sensitivity analysis results show that the exchange of p,p′‐DDE can be sensitive to either the sediment sorption/desorption parameters or colloidal parameters depending on the experimental conditions tested. For the experimental conditions employed here, the effect of colloids on contaminant transport is expected to be minimal, and the stream–subsurface exchange of p,p′‐DDE is dominated by the interaction of p,p′‐DDE with bed sediment. The work presented here contributes to a better mechanistic understanding of the complex transport process that hydrophobic organic contaminants undergo in natural streams and to the development of reliable, predictive models for the assessment of impacted streams. Copyright © 2015 John Wiley & Sons, Ltd. 相似文献
9.
Determining sources, quantities and travel distances of eroding soil is of increasing importance given its impact on‐ and off‐site, the sediment‐associated transport of nutrients, metals and micro‐organisms and the ongoing need to provide data for soil erosion model development and validation. Many soil tracers have been developed; however, most comprise foreign materials, such as fluorescent beads and rare earth oxides, which cast doubts on the validity of tracing results given their different physical characteristics. To avoid these problems, we have investigated the potential of soil, which has been heated under reducing conditions to enhance its ferrimagnetic content, as a soil erosion tracer; while the technique has been used successfully to trace river sediment it has not been successfully applied to soil erosion studies. For a suite of 16 magnetic concentration‐dependent properties, values were found to be significantly greater, by at least one order of magnitude, after heating, both for the bulk soil and nine individual particle size fractions. Individual size fractions could be differentiated using two different magnetic properties, thus illustrating the technique's potential to provide information on particle size‐specific erosion. Soil box experiments demonstrated the potential for both in situ measurement of magnetic susceptibility and laboratory measurement of the magnetic properties of eroded sediment, to trace and quantify soil erosion. Thus, heated soil, with artificially‐enhanced ferrimagnetic properties, is successfully demonstrated to have great potential as a size‐specific, cost‐effective and representative soil erosion tracer. Copyright © 2012 John Wiley & Sons, Ltd. 相似文献
10.
Tracer studies are a commonly used tool to develop and test Einstein-type stochastic bedload transport models. The movements of these tracers are controlled by many factors including grain characteristics, hydrologic forcing, and channel morphology. Although the influence of these sediment storage zones related to morphological features (e.g., bars, pools, riffles) have long been observed to “trap” bedload particles in transport, this influence has not been adequately quantified. In this paper we explore the influence of channel morphology on particle travel distances through the development of a Bayesian survival process model. This model simulates particle path length distributions using a location-specific “trapping probability” parameter (pi ), which is estimated using the starting and ending locations of bedload tracers. We test this model using a field tracer study from Halfmoon Creek, Colorado. We find that (1) the model is able to adequately recreate the observed multi-modal path length distributions, (2) particles tend to accumulate in trapping zones, especially during large floods, and (3) particles entrained near a trapping zone will travel a shorter distance than one that is further away. Particle starting positions can affect path lengths by as much as a factor of two, which we confirm by modelling “starting-location-specific” path length probability distributions. This study highlights the importance of considering both tracer locations and channel topography in examinations of field tracer studies. © 2020 John Wiley & Sons, Ltd. 相似文献
11.
Fine particulate organic matter (FPOM) represents a major component of stream organic matter budgets, and its dynamics greatly affect the productivity and metabolism of a stream community. FPOM transport dynamics has been well documented in high-gradient streams with rocky substrates, but information from low-gradient, sandy-bottom streams has been lacking. We estimated FPOM retention patterns in Payne Creek, a 2nd order Coastal Plain stream (USA), under naturally varying hydraulic conditions (discharge and velocity). Corn pollen, as an FPOM analogue, was released along with a conservative solute tracer and the particle retention coefficient (k p) was calculated by fitting the ratio of total pollen remaining in the water column against the longitudinal transport distance to an exponential decay model. Pollen k p (n = 4) ranged from 0.034 to 0.214 /m, and particle transport distance (S p) ranged from 4.7 to 29.7 m. The S p measured in Payne Creek was in the lowest range of previously reported values, and such rapid particle retention was attributed to the low channel slope and slow current velocity. S p was significantly correlated to water velocity and the channel friction factor, but not to discharge (Q). Two summer experiments conducted in contiguous stream segments resulted in the shortest (4.7 m) and longest (29.7 m) S p, despite the similar Q. This was attributed to the segment-scale channel alterations that occurred during the previous winter, which led to very different hydraulic conditions in the two stream segments. In Payne Creek, seasonal changes in hydrology and segment-scale variation in channel morphology were the main factors controlling FPOM transport and retention. 相似文献
12.
This study investigates sediment transport at a very low‐energy backbarrier beach in southern Portugal, from a spring‐to‐neap tide period, during fair‐weather conditions. Rates and directions of transport were determined based on the application of fluorescent tracer techniques. Wind and currents were collected locally, whereas the dominant small and short‐period wind waves were characterized using a morphodynamic modelling system coupling a circulation model, a spectral wave model, and a bottom evolution model, well validated over the study area. For the recorded conditions sediment transport was small and ebb oriented, with daily transport rates below 0.02 m3 day‐1. Tidal currents (mainly ebb velocities) were found to be the main causative forcing controlling sediment displacements. Transport rates were higher during spring tides, tending towards very small values at neap tides. Results herein reported points towards the distinction between tracer advection and tracer dispersion in this type of environment. Transport by advection was low as a consequence of the prevailing hydrodynamic conditions (Hs < 0.1 m, and max. current velocity of 0.5 m s‐1) and the tracer adjustment to the transport layer, whereas dispersion was relatively high (few metres per day). Tracer techniques allowed distinguishing the broad picture of transport, but revealed the need for refinement in this type of environments (bi‐directional forcing by ebb and flood cycles). Copyright © 2012 John Wiley & Sons, Ltd. 相似文献
13.
A tracer test was conducted in a laboratory chamber representing a two‐dimensional aquifer to investigate the longitudinal dispersivity (αL) and the ratio (αT/αL) of transverse to longitudinal dispersivity of sandy aquifer materials. Dispersive parameters were obtained by matching the observed chloride plumes at 9 hours and 16 hours after tracer injection with those simulated by a flow and transport model. The best match was found for αL = 0·2 ? 0·25 cm and αT/αL = 0·2. The ratio of αT/αL = 0·2 was within the range of laboratory values reported in the literature. Sensitivity analysis revealed that the tracer plume concentration and shape were more sensitive to variations in longitudinal dispersivity than to the ratio of transverse to longitudinal dispersivity. This result contrasted with findings of others, showing that the dispersivity ratio greatly affects contaminant plume shape. However, our experimental boundary conditions restricted expansion of the plume normal to the direction of flow and thus affected the parameter estimation. Copyright © 2004 John Wiley & Sons, Ltd. 相似文献
14.
Hydraulic fracturing has become an important technique for enhancing the permeability of hydrocarbon source rocks and increasing aquifer transmissivity in many hard rock environments where natural fractures are limited, yet little is known about the nature or behaviour of these hydraulically induced fractures as conduits to flow and transport. We propose that these fractures tend to be smooth based on observed hydraulic and transport behaviour. In this investigation a multi‐faceted approach was used to quantify the properties and characteristics of an isolated hydraulically induced fracture in crystalline rocks. Packers were used to isolate the fracture that is penetrated by two separate observation wells located approximately 33 m apart. A series of aquifer tests and an induced gradient tracer test were performed to better understand the nature of this fracture. Aquifer test results indicate that full recovery is slow because of the overall low permeability of the crystalline rocks. Drawdown tests indicate that the fracture has a transmissivity of 1–2 m2/day and a specific storage on the order of 2–9 × 10?7/m. Analysis of a potassium–bromide tracer test break through curve shows classic Fickian behaviour with minimal tailing analogous to parallel plate flow. Virtually all of the tracer was recovered, and the breakthrough curve dilution indicates that the swept area is only about 11% of a radial flow field and the estimated aperture is ≤0.5 mm, which implies a narrow linear flow region. These outcomes suggest that transport within these hydraulically induced ‘smooth’ fractures in crystalline rocks is rapid with minimal mixing, small local velocity fluctuations and no apparent diffusion into the host rock or secondary fractures. Copyright © 2016 John Wiley & Sons, Ltd. 相似文献
15.
Simulation of less‐mobile porosity dynamics in contrasting sediment water interface porous media 下载免费PDF全文
下载免费PDF全文 Farzaneh MahmoodPoor Dehkordy Martin A. Briggs Frederick D. Day‐Lewis Amvrossios C. Bagtzoglou 《水文研究》2018,32(13):2030-2043
Considering heterogeneity in porous media pore size and connectivity is essential to predicting reactive solute transport across interfaces. However, exchange with less‐mobile porosity is rarely considered in surface water/groundwater recharge studies. Previous research indicates that a combination of pore‐fluid sampling and geoelectrical measurements can be used to quantify less‐mobile porosity exchange dynamics using the time‐varying relation between fluid and bulk electrical conductivity. For this study, we use macro‐scale (10 s of cm) advection–dispersion solute transport models linked with electrical conduction in COMSOL Multiphysics to explore less‐mobile porosity dynamics in two different types of observed sediment water interface porous media. Modeled sediment textures contrast from strongly layered streambed deposits to poorly sorted lakebed sands and cobbles. During simulated ionic tracer perturbations, a lag between fluid and bulk electrical conductivity, and the resultant hysteresis, is observed for all simulations indicating differential loading of pore spaces with tracer. Less‐mobile exchange parameters are determined graphically from these tracer time series data without the need for inverse numerical model simulation. In both sediment types, effective less‐mobile porosity exchange parameters are variable in response to changes in flow direction and fluid flux. These observed flow‐dependent effects directly impact local less‐mobile residence times and associated contact time for biogeochemical reaction. The simulations indicate that for the sediment textures explored here, less‐mobile porosity exchange is dominated by variable rates of advection through the domain, rather than diffusion of solute, for typical low‐to‐moderate rate (approximately 3–40 cm/day) hyporheic fluid fluxes. Overall, our model‐based results show that less‐mobile porosity may be expected in a range of natural hyporheic sediments and that changes in flowpath orientation and magnitude will impact less‐mobile exchange parameters. These temporal dynamics can be assessed with the geoelectrical experimental tracer method applied at laboratory and field scales. 相似文献
16.
The goal of this research was to compare hyporheic activity in recently restored and adjacent un‐restored reaches of the Truckee River downstream from the Reno/Sparks metropolitan area. The installation of rocky riffles and raised channel bed elevations in the restored reaches may have increased the degree of surface–subsurface interaction. A fluctuating chloride concentration signal served as the tracer, induced by the variable influx of higher salinity water several miles upstream from the study reach. The solute transport model, OTIS, was used in conjunction with the hydrodynamic model, DYNHYD5, to estimate transient storage parameters under unsteady flow conditions. The model was calibrated to chloride concentrations measured over a period of three days at six in‐stream locations representing restored and un‐restored reaches. An automated parameter estimation algorithm (SCE‐UA) was used to optimize parameters for multiple reaches simultaneously and generate a distribution of parameter estimates. Results suggest that the transient storage zone cross‐sectional area (As) is larger in the restored reaches than in the unrestored reaches, but the exchange coefficient (α) is smaller, leading to increased hyporheic residence time and hydrologic retention in the vicinity of channel reconstructions. Scenarios were used to simulate the potential effects of increased subsurface residence time on denitrification and in‐stream NO3‐N concentrations. Monte Carlo analysis was performed to assess uncertainty in the simulation results and show the potential for greater nutrient retention in the lower Truckee River as a result of channel restoration. Copyright © 2009 John Wiley & Sons, Ltd. 相似文献
17.
Clogging of saturated porous media by silt‐sized suspended solids under varying physical conditions during managed aquifer recharge 下载免费PDF全文
下载免费PDF全文 Managed aquifer recharge is an effective method for utilizing excess flood flows, but clogging of porous media is a limiting factor in the implementation of this water storage technique. In recent years, much research on the physical clogging of porous media during artificial recharge has been conducted. However, the understanding of clogging due to silt‐sized suspended solids (SS) is still inadequate, especially under varying physical conditions. Here, we subjected sand columns to controlled rates of flow and SS suspensions to investigate the influence of media size, SS size, SS concentration, and flow velocity on the clogging of porous media by silt‐sized SS. The results show that the diameter ratio of SS particles to sand grains is the dominant factor influencing the position of physical clogging. As pore velocity increased, the mobility of silt‐sized SS was enhanced and retention in the porous media decreased noticeably. The spatial retention profiles in the porous media were found to vary greatly at different flow velocities. The SS concentration of the infiltrating suspension also dramatically influenced the mobility and deposition of silt‐sized SS particles, such that high concentrations accelerated the clogging process. As the different physical factors changed, the breakthrough curves and retention profiles of silt‐sized SS particles changed obviously and the mechanisms of retention differed. On the whole, clogging position is mainly determined by particle size ratio, but clogging rate is dominated by a variety of factors including particle size ratio, SS concentration, and flow velocity. 相似文献
18.
Influence of bed clusters and size gradation on operational time distribution for non‐uniform bed‐load transport 下载免费PDF全文
下载免费PDF全文 The operational time distribution (OTD) defines the time for bed‐load sediment spent in motion, which is needed to characterize the random nature of sediment transport. This study explores the influence of bed clusters and size gradation on OTD for non‐uniform bed‐loads. First, both static and mobile bed armouring experiments were conducted in laboratorial flumes to monitor the transport of mixed sand/gravel sediments. Only in the mobile armouring experiment did apparent bed clusters develop, because of stable feeding and a longer transport period. Second, a generalized subordinated advection (GSA) model was applied to quantify the observed dynamics of tracer particles. Results show that for the static armour layer (without sediment feed), the best‐fit OTD assigns more weight to the large displacement of small particles, likely because of the size‐selective entrainment process. The capacity coefficient in the GSA model, which affects the width of the OTD, is space dependent only for small particles whose dynamics can be significantly affected by larger particles and whose distribution is more likely to be space dependent in a mixed sand and gravel system. However, the OTD for the mobile armour layer (with sediment recirculation) exhibited longer tails for larger particles. This is because the trailing edge of larger particles is more resistant to erosion, and their leading front may not be easily trapped by self‐organized bed clusters. The strong interaction between particle–bed may cause the capacity coefficient to be space‐dependent for bed‐load transport along mobile armour layers. Therefore, the combined laboratory experiments and stochastic model analysis show that the OTD may be affected more by particle–bed interactions (such as clusters) than by particle–particle interactions (e.g. hiding and exposing), and that the GSA model can quantify mixed‐size sand/gravel transport along river beds within either static or mobile armour layers. Copyright © 2016 John Wiley & Sons, Ltd. 相似文献
19.
Fluid flow exerts a critical impact on the convection of thermal energy in geological media, whereas heat transport in turn affects fluid properties, including fluid dynamic viscosity and density. The interplay of flow and heat transport also affects solute transport. To unravel these complex coupled flow, heat, and solute transport processes, here, we present a theory for the idealized scale‐dependent Poiseuille flow model considering a constant temperature gradient (?T) along a single fracture, where fluid dynamic viscosity connects with temperature via an exponential function. The idealized scale‐dependent model is validated based on the solutions from direct numerical simulations. We find that the hydraulic conductivity (K) of the Poiseuille flow either increases or decreases with scales depending on ?T > 0°C/m or ?T < 0°C/m, respectively. Indeed, the degree of changes in K depends on the magnitude of ?T and fracture length. The scale‐dependent model provides an alternative explanation for the well‐known scale‐dependent transport problem, for example, the dispersion coefficient increases with travel distance when ?T > 0°C/m according to the Taylor dispersion theory, because K (or equivalently flux through fractures) scales with fracture length. The proposed theory unravels intertwined interactions between flow and transport processes, which might shed light on understanding many practical geophysical problems, for example, geothermal energy exploration. 相似文献
20.
Tracer experiments conducted in the laboratory on undisturbed core samples (<7.3-cm-diameter) have been a standard method for estimating hydraulic and transport properties of fractured till since the 1980s. This study assesses the relationship between visible fractures on the top and bottom of core samples and the resulting hydraulic and mass transport properties of the core. We hypothesized that more visible fractures would indicate the presence of a well-connected fracture network, leading to greater hydraulic conductivity (K) values and earlier chemical breakthrough times. To test this hypothesis, water flow and bromide (Br-) tracer experiments were performed on 10, 16-cm diameter, 16-cm-tall samples of fractured Dows Formation till from central Iowa. Visually identifiable fractures were present on the top and bottom of every sample. Results indicate that the visual identification of fractures does not predict a connected fracture network, as some samples produced breakthrough curves showing rapid first arrival times and shapes characteristic of solute transport in a fractured medium, while others appeared similar to an unfractured medium. No correlation was found between the number of visible fractures and K (Pearson's r = 0.25), or Br- first arrival time (r = −0.33), but a strong negative correlation between K and first arrival time (r = −0.92). Results indicate that the sample volume was not large enough to reliably contain a connected fracture network. Thus, testing large volumes of till at the field scale coupled with fracture-flow modeling likely represents the best approach for estimating hydraulic and mass transport properties for fractured till. 相似文献