共查询到20条相似文献，搜索用时 203 毫秒
1.
通过固结不排水三轴压缩试验,分析了围压、固结比和干密度等因素对饱和粉土静态液化特性的影响。试验结果表明,在干密度较小时,饱和粉土的偏应力-应变曲线呈现明显的硬变软化型,随轴向应变增大超静孔隙水压力增加、有效应力减小而发生静态液化,当干密度达到1.58 g· cm-3时,饱和粉土的偏应力-应变曲线表现出硬变硬化现象,超静孔隙水压力为负值或接近0,饱和粉土不再发生静态液化,即饱和粉土存在静态液化的干密度临界值;其他条件不变,随着围压、固结比或干密度的增大,偏应力峰值和残余强度均增大,静态液化势降低;根据有效应力路径建立了流滑面以作为饱和粉土稳定区与非稳定区的分界面。 相似文献
2.
钙质砂是海洋钙质生物死亡后形成的一种具有丰富内部孔隙、低强度、不规则形状和易破碎的岩土材料。通过对钙质砂分别开展的等向压缩、常规三轴压缩、平均主应力为常数的三轴压缩、减压的三轴压缩和等应力比加载5种试验,探讨了不同应力路径下钙质砂的力学及变形特性。试验结果表明应力路径对钙质砂的抗剪强度和变形特征具有重要影响。钙质砂在等向压缩条件下具有明显的各向异性特征;常规三轴压缩试验条件下,密实钙质砂呈现低压剪胀、高压剪缩的变形特征,且峰值强度与初始固结压力之间呈幂函数关系;平均主应力为常数的三轴压缩试验中,增加偏应力会引起试样的体变;与常规三轴压缩试验不同,在减压的三轴压缩试验中,应力-应变关系曲线均表现为应变软化;而等应力比加载试验中,试样基本处于弹性状态下,且轴向应力与轴向应变之间呈幂函数关系。试验结果还发现钙质砂的切线泊松比不仅要考虑钙质砂的变形和应力状态等的影响,还要考虑应力路径的影响。不同应力路径试验条件下峰值应力比大小顺序与最大体变大小顺序不受初始固结压力的影响。钙质砂的峰值内摩擦角均随着初始固结压力的增大而减小,大致与初始固结压力的对数呈线性函数关系。 相似文献
3.
通过对钙质砂进行不排水条件下声发射试验,探讨了不同围压、剪切速率、初始孔隙比和级配下钙质砂声发射规律。试验结果表明:低围压（围压低于400 kPa）时,钙质砂声发射活动频率随着围压的升高而增加;围压增至800 kPa时,声发射活动频率有所下降。低剪切速率下,钙质砂剪切试验明显分为颗粒破碎阶段和颗粒滑移阶段,随着剪切速率增大,二者之间较模糊,不能明显区分;松散和密实状态下,钙质砂声发射活动规律相似,钙质砂声发射活动频率均高于中密状态钙质砂;级配较好的钙质砂,声发射率峰值出现在试样发生剪切破坏前;级配稍差,试样声发射率相对均匀,声发射率峰值出现在邻近试验结束时。 相似文献
4.
为了分析剪切条件下零有效应力状态砂土的流动变形规律,对传统环剪仪进行了试样可视化改造,研制了透明环形剪切盒,通过对剪切盒膨胀性能分析及与标准砂的剪切试验对比,验证了环剪装置改造的合理性。通过分析不排水条件下饱和悬浮塑料砂的剪应力-应变曲线,发现其剪切强度具有应变软化的特性。通过分析环剪仪中饱和悬浮塑料砂试样的有效应力,证实了可视环剪试验中的土体基本处于零有效应力状态。开展了饱和悬浮塑料砂的流动变形可视环剪试验研究,结果表明：饱和悬浮塑料砂在固结不排水条件下剪切变形不连续,直接在剪切面发生断裂;在不固结不排水的条件下饱和悬浮塑料砂的剪切变形表现出流动形态,且与剪切速率有关：在低剪切速率下,剪切变形仅在剪切面处形成具有曲线轨迹的流动变形而在其他区域不发生变形;而在高剪切速率下剪切变形为整体的倾斜变形,符合黏性流体的流动变形特征。 相似文献
5.
为探究细粒含量FC、相对密实度D_r、初始有效围压■对饱和砂-粉混合料剪切波速V_s的影响,对不同FC、D_r和■组合情况的混合料开展了一系列弯曲元试验。试验表明:随着FC的增加,松散-中密混合料的V_s先减小再增大,而密实混合料的V_s呈减小趋势;FC相同时混合料的V_s与固结后孔隙比e_c呈负线性关系,但不同FC的混合料的V_s与e_c没有单一的负线性关系;不同FC、D_r、■组合的砂-粉混合料的V_s与等效骨架孔隙比e_(sk)*具有很好的负线性关系。文献中三类砂-粉混合料的V_s试验数据也佐证了这一结论。这说明e_(sk)*是与砂-粉混合料V_s唯一具有负线性相关的物理状态指标。 相似文献
6.
淞江古河道内地基土由饱和、呈松散—稍密状态亚砂土夹轻亚粘土、粉细砂等组成,各工点组成的地基土类型、反映在地震烈度7°时极易产生液化。产生严重液化深度主要在埋深3～10米,埋深10米以下往往仅具轻微液化。故于古河道内拟建建筑物,应重视地基土的液化判别工作,以利于地基土的处理。 相似文献
7.
黄土边坡开挖过程中常遇到边坡发生变形甚至破坏的情况,不同的开挖速率导致边坡的变形特征也不相同。通过饱和黄土的卸载三轴试验,研究固结围压及卸载速率对卸载状态下饱和黄土的应力-应变特性、孔隙水压力的发展及应力路径的影响。试验表明,固结围压越大,土体破坏所需的偏应力越大,抗剪强度越大;卸载速率越大,对应的偏应力峰值越大,抗剪强度越大。卸载速率相同时,土体卸载初期的超静孔压为负值,增大至正值后孔压的增长速率在其增大过程中逐渐减小;固结围压越大,土样剪切过程中对应的孔隙水压力越大。卸载三轴试验中,土体均表现为应变软化的特性;饱和黄土破坏时的应变均为1%~3%,且固结围压越高,破坏时的应变越小。固结围压相同时,卸载速率越大,孔压增长速率越快,但孔隙水压力值越小。 相似文献
8.
为研究主应力轴旋转复杂动应力对偏压固结粉土的性状演变影响,以空心圆柱试样为对象,开展具有不同初始固结比的密实粉土（Dr＝70%）在不排水主应力轴循环旋转下的系列试验。结果表明：①初始固结比不大于1.5时,主应力轴旋转导致试样发生中低应变崩塌,进而液化的脆性破坏模式;而固结比大于1.5时,试样变为应变持续稳定开展至高应变,孔压最终进入动态平衡的延性破坏模式,且不同固结比下试样发生崩塌液化和稳态延性破坏的孔压峰值间不存在交叉。②小偏压固结试样的液化峰值孔压和崩塌孔压均随固结比增加而有规律地下降,但受动剪应力水平影响很小,这与等压固结试样的崩塌孔压值受控于剪应力水平有很大差异。③相同初始球应力水平下,崩塌振次反映的小偏压固结试样强度高于等压固结试样,但在偏压条件下强度与固结比不存在单调变化关系,表明小偏压固结试样崩塌除受制初始围压水平外,很大程度上还取决于偏压程度。④基于上述试验结果,提出了主应力轴循环旋转下小偏压固结粉土的孔压预测模型,该模型不仅突显了崩塌状态对相变及液化破坏的重要预测作用,还反映了固结比和动剪应力对孔压开展的综合影响。 相似文献
9.
天津宝坻县隐伏岩溶区地下水开发与地裂缝成生关系研究 总被引：5，自引：0，他引：5
在调查分析地裂缝时空分布特征的基础上,研究地裂活动与区内水文地质条件、地下水开采过程的关系,认为过量开采奥灰水是产生地裂缝的主导因素。随着水位下降,盖层介质固结压密作用是导致地面压缩变形乃至地裂缝发生的直接原因。地下水系统结构特征以及固结压密作用的物质基础———松散盖层的厚度、岩性,是构成地面不均匀沉降的充要条件。当这种不均匀变形程度足以使土体连续性破坏时,则地裂缝便在沉降区应力集中的部位发生。 相似文献
10.
由于吹填过程的水力分选作用钙质砂土地基颗粒分布不均匀,容易形成分布不均、形态各异的以不同细粒含量的粉细砂层为主的细粒汇集层,引起钙质砂土地基承载力和不均匀沉降问题。开展不同细粒含量的粉细砂三轴固结排水剪切试验,分析细粒含量对钙质砂土力学特性的影响。研究结果表明,（1）当细粒含量增加时相同围压下土样剪胀性逐渐减弱,且峰值偏应力也逐渐减小;（2）各组试样干密度为1.40 g/cm3状态下各含量粉细砂均表现出应变软化特征,当细粒含量为10%时粉细砂土体强度稳定性最差,之后稳定性随细粒含量增加而逐渐增大;（3）钙质细砂由于颗粒咬合作用,具有表观黏聚力,当细粒含量小于40%时,随着细粒含量增加,颗粒之间的咬合作用显著降低,表观黏聚力线性减小。研究成果可为粉细砂层的地基处理及边坡稳定分析提供参考。 相似文献
11.
Wiam Khebizi Sidali Denine Jean Canou Jean-Claude Dupla 《Geomechanics and Geoengineering》2019,14(1):30-40
Soil improvement using fibres is widely used in soil stabilisation to prevent sand liquefaction. In order to study the undrained behaviour and liquefaction resistance of sand reinforced with polypropylene fibres, a series of triaxial compressive tests were conducted on unreinforced and reinforced Chlef sand with different contents of polypropylene fibres (0, 0.3, 0.5 and 0.8%). Samples were prepared at 30% and 80% relative densities representing loose and dense states respectively, and triaxial tests were performed at confining pressures of 50, 100 and 200 kPa. Tests results show that fibre inclusion has a significant effect on the shear strength and dilation of sandy soil. The increase in strength is function of fibre content, relative density and confining pressure. The maximum strength improvement for both loose and dense fibre-reinforced sand is more pronounced at higher confining pressure and at higher fibre content. 相似文献
12.
The effects of initial state of the samples and the overconsolidation ratio (OCR) on the behavior of Chlef sand were studied in this article. For this purpose, the results of two series of undrained monotonic triaxial compression tests on medium dense sand are presented. In the first test series, the influence of the specimen's fabric and confining pressure has been studied. The tests were conducted at initial confining pressure of 50, 100, and 200 kPa. Two methods of sample preparation, which included the dry funnel pluviation and the wet deposition, were utilized. All the samples were subjected to a monotonic loading after consolidation phase. The results of the tests demonstrate that an increase in initial confining pressure leads to an increase in the resistance to liquefaction. The results also show that the samples prepared with the dry funnel pluviation method exhibit a greater resistance to liquefaction than those prepared with the wet deposition method. In the second series of tests, the overconsolidation influence on the resistance to the sand liquefaction has been realized on samples at an effective stress of 100 kPa for OCR varying between 1 and 8. The tests show that the increase of OCR improves the stiffness of sand and accelerates the appearance of dilatancy. 相似文献
13.
Shear strength and pore-water pressure characteristics of sandy soil mixed with plastic fine 总被引：1，自引：0，他引：1
Recent earthquake case histories have revealed the liquefaction of mixtures of sand and fine particles during earthquakes. Different from earlier studies which placed an emphasis on characterisation of liquefaction in terms of the induced shear stress required to cause liquefaction, this study adopted a strain approach because excess pore-water pressure generation is controlled mainly by the level of induced shear strains. The current study includes the results of a set of laboratory tests carried out on sand specimens with the same relative densities and variation in the plastic fines (kaolinite or bentonite) contents ranging from 0 to either 30 % and consolidated at mean confining pressure of 100, 200 and 300 kPa using static triaxial test apparatus, in order to study the influence of fine content and other parameters on the undrained shear strength and liquefaction potential of clayey sand specimens; also, pore-water pressures in the specimens are discussed. Results of tests show that the peak strength decreases as the fines (kaolinite or bentonite) content increases up to a threshold content of fines (FCth) after which, increases in plastic fine content lead to improve the peak shear strength of specimens, and also the ultimate steady-state strength has been improved due to the increased in plastic fines content. Also, pore pressure build-up in clayey sands is generally slower than that observed in pure sand. 相似文献
14.
为研究钙质砂剪切特性的围压效应和粒径效应,开展了在不同粒径、不同相对密实度以及不同围压条件下的三轴剪切试验,并引入应力相对软化系数和剪胀系数对应变软化特征及剪胀特征进行了定量表征。试验研究表明,随围压的增大,不同粒径钙质砂试样应变软化特征及剪胀特征逐渐减弱,且围压与应力相对软化系数和剪胀系数均呈半对数线性相关。不同粒径钙质砂试样存在一强度临界围压和体变临界围压分别使得应变软化特征和剪胀特征消失。在粒径为5～0.075 mm范围内,对松样而言,围压对软化特征和剪胀特征存在显著影响,但与粒径不存在显著相关性;对密样而言,随粒径逐渐减小,围压对试样软化特征的影响逐渐增强,而对试样剪胀特征的影响逐渐减弱。在低围压（50 kPa）条件下,0.5～0.25 mm粒径组试样破碎最显著。 相似文献
15.
In practical engineering, cyclic shear stresses induced by earthquakes, traffic, and waves are superimposed on the initial static shear stress in sand fills or deposits, leading to complex responses of soils such as their deformation characteristics, pore pressure generation, and susceptibility (or cyclic resistance) to liquefaction. To experimentally investigate the undrained cyclic response of saturated sand, a series of triaxial tests were performed, covering a broad range of initial static and cyclic deviatoric stress levels. The results indicate that different stress conditions lead to two types of cyclic behavior: cyclic mobility and residual deformation accumulation. The compressional static stress is beneficial to the cyclic resistance of the dense sand, whereas the extensional static stress is regarded as detrimental as it tended to reduce the cyclic strength. Moreover, by comparing the available test data obtained from the same sand with varying initial densities and confining pressures, the static shear effect on cyclic resistance was found to be dependent on the state of the sand. Compared to the interpretation made using the limiting pore pressure-based criterion, the conventional failure criterion using a cyclic axial strain of 5% may lead to a substantial overestimation of the cyclic resistance, thus resulting in unsafe assessment and design. Hence, by employing the pore pressure criterion, the pore pressure generated in the cyclic tests was investigated and was found to be significantly influenced by the static shear stress. A pore pressure generation model is proposed to obtain the pore pressure characteristics of sand under various static shear stress conditions. 相似文献
16.
Hanifi Missoum Mostefa Belkhatir Karim Bendani Mustapha Maliki 《Geotechnical and Geological Engineering》2013,31(1):279-296
In a number of recent case studies, the liquefaction of silty sands has been reported. To investigate the undrained shear and deformation behaviour of Chlef sand–silt mixtures, a series of monotonic and stress-controlled cyclic triaxial tests were conducted on sand encountered at the site. The aim of this laboratory investigation is to study the influence of silt contents, expressed by means of the equivalent void ratio on undrained residual shear strength of loose, medium dense and dense sand–silt mixtures under monotonic loading and liquefaction potential under cyclic loading. After an earthquake event, the prediction of the post-liquefaction strength is becoming a challenging task in order to ensure the stability of different types of earth structures. Thus, the choice of the appropriate undrained residual shear strength of silty sandy soils that are prone to liquefaction to be used in engineering practice design should be established. To achieve this, a series of undrained triaxial tests were conducted on reconstituted saturated silty sand samples with different fines contents ranging from 0 to 40 %. In all tests, the confining pressure was held constant at 100 kPa. From the experimental results obtained, it is clear that the global void ratio cannot be used as a state parameter and may not characterize the actual behaviour of the soil as well. The equivalent void ratio expressing the fine particles participation in soil strength is then introduced. A linear relationship between the undrained shear residual shear strength and the equivalent void ratio has been obtained for the studied range of the fines contents. Cyclic test results confirm that the increase in the equivalent void ratio and the fines content accelerates the liquefaction phenomenon for the studied stress ratio and the liquefaction resistance decreases with the increase in either the equivalent void ratio or the loading amplitude level. These cyclic tests results confirm the obtained monotonic tests results. 相似文献
17.
轨道交通振动下南京片状细砂的有效应力路径及破坏模式 总被引：2，自引：1，他引：1
以南京片状结构细砂为研究对象,采用英国WFI动静多功能三轴仪,研究了饱和南京片状结构细砂在列车振动荷载作用下静偏应力水平、循环应力比对其动力特性的影响;把振动孔压的发展与应力路径相联系,分析了循环荷载作用下不同阶段南京片状结构细砂所处的初始压密状态、压缩状态和膨胀状态的发生和发展过程;同时,根据静偏应力与循环偏应力的大小,视有无偏应力反向,南京片状结构细砂的破坏模式可分为循环活动性和塑性应变累积破坏,并对其循环活动性的机制进行了初步探讨。 相似文献
18.
Awad A. Al-Karni 《Arabian Journal of Geosciences》2011,4(7-8):1095-1101
The shear strength of cohesionless soil is reduced as the water pressure inside the pores of the soil mass increases. The mathematical relationship between the shear strength and the pore water pressure was derived using Mohr–Coulomb failure criteria as a function of the confining pressure and the effective angle of friction. Experimentally, a series of consolidated drained triaxial tests with back pore water pressure was run on samples of saturated uniform dense sand. The tests were conducted at different confining pressures in the range of 100–400 kPa with an increment of 100 kPa. At each level of confining pressure, the tests were repeated at different values of back pore water pressure in the range of 0–100 kPa with an increment of 25 kPa. For each test, the initial applied back pore water pressure was kept constant during the test for comparing the results at the same effective confining pressure. This study concludes that the mathematical relationship gives accurate results at any level of confining pressure and/or pore water pressure as a function of the effective angle of friction that can be evaluated using single consolidated drained triaxial test at zero back pore water pressure. 相似文献
19.
四氢呋喃水合物沉积物静动力学性质试验研究 总被引：1，自引：0，他引：1
利用研制的天然气水合物沉积物合成与力学性质测试一体化试验设备,以粉细砂土和蒙古砂土作为沉积物骨架,对四氢呋喃(THF)水合物沉积物进行了静动三轴试验,获得了水合物分解前后沉积物样品的应力-应变关系、强度和液化特性,对两种骨架的水合物沉积物的性质进行了对比,同时将水合物分解后的沉积物与对应的饱和土的动三轴试验结果进行了对比。结果表明：水合物沉积物均表现为塑性破坏;围压越大,水合物沉积物强度越高;水合物分解导致沉积物的强度大幅降低;水合物分解后沉积物液化所需的时间较饱和水沉积物缩短 相似文献
20.
城市生活垃圾焚烧炉渣具有活性,饱和炉渣的剪切强度随时间增加而增加。本文采用常规三轴试验测试饱和炉渣的剪切强度,围压σ3分别为50kPa、100kPa、200kPa和400kPa,试样的干密度ρd分别为1.4g·cm-3、1.5g·cm-3和1.6g·cm-3,龄期t分别为3d、7d、14d和28d。三轴试验结果表明:饱和炉渣的破坏模式受龄期和围压的影响明显。围压小于200kPa,龄期小于14d的试样表现为脆性破坏。在τ-σ坐标上,应力莫尔圆的包络线不是直线;炉渣在σ1-σ3坐标上表现为两段直线,分界点为σ3=200kPa,由σ1-σ3相关关系确定炉渣的内摩擦角和黏聚力更合理可信。 相似文献