共查询到20条相似文献，搜索用时 15 毫秒
1.
Sedimentary porous rocks can be used for long-term subsurface containment of CO2. Before injecting CO2 to sedimentary reservoirs, it is necessary to perform stability analysis of the reservoir and to estimate the maximum sustainable pore fluid pressures. In order to avoid the reservoir damage during the CO2 injection, the effective stresses in the reservoir should be evaluated. In this paper, numerical modeling techniques are used for the evaluation of stresses and deformations in a naturally fractured carbonate sedimentary reservoir. The developed numerical modeling scheme couples the behavior of the CO2 injection and the change in the geomechanical behavior of the sedimentary carbonate reservoir for a case study from Saudi Arabia. The present investigation extends the previous studies by considering the sorption-based deformation during the injection of the compressed CO2 fluid into the Arab-D naturally fractured carbonate reservoir. The change in permeability during the injection of CO2 is evaluated. The adopted CO2 injection scenario was shown to be within the safe maximum occupancy, and that the increase in the pore pressure does not result in the reservoir failure. 相似文献
2.
Laura Chiaramonte Mark D. Zoback Julio Friedmann Vicki Stamp 《Environmental Geology》2008,54(8):1667-1675
This paper reports a preliminary investigation of CO2 sequestration and seal integrity at Teapot Dome oil field, Wyoming, USA, with the objective of predicting the potential risk
of CO2 leakage along reservoir-bounding faults. CO2 injection into reservoirs creates anomalously high pore pressure at the top of the reservoir that could potentially hydraulically
fracture the caprock or trigger slip on reservoir-bounding faults. The Tensleep Formation, a Pennsylvanian age eolian sandstone
is evaluated as the target horizon for a pilot CO2 EOR-carbon storage experiment, in a three-way closure trap against a bounding fault, termed the S1 fault. A preliminary geomechanical
model of the Tensleep Formation has been developed to evaluate the potential for CO2 injection inducing slip on the S1 fault and thus threatening seal integrity. Uncertainties in the stress tensor and fault
geometry have been incorporated into the analysis using Monte Carlo simulation. The authors find that even the most pessimistic
risk scenario would require ∼10 MPa of excess pressure to cause the S1 fault to reactivate and provide a potential leakage
pathway. This would correspond to a CO2 column height of ∼1,500 m, whereas the structural closure of the Tensleep Formation in the pilot injection area does not exceed
100 m. It is therefore apparent that CO2 injection is not likely to compromise the S1 fault stability. Better constraint of the least principal stress is needed to
establish a more reliable estimate of the maximum reservoir pressure required to hydrofracture the caprock. 相似文献
3.
4.
5.
Zhang Liaoyuan Qu Zhanqing Zhai Mingyang Li Aishan Huang Bo Zhang Zilin 《Geotechnical and Geological Engineering》2021,39(2):839-854
Tight heterogeneous glutenite reservoir is typically not easy to form complex hydraulic fracture (HF) due to its poor physical properties, poor matrix seepage capacity, and small limit discharge radius and undeveloped natural fracture system. To improve the HF complexity and the stimulated reservoir volume (SRV), a novel stimulation technology called CO2 miscible fracturing has been introduced and its fracturing mechanism has been studied. The CO2 miscible fracturing modifies the in situ stress field by injecting low viscosity fluid to increase the HF complexity and SRV. Therefore, a series of numerical simulations based on a hydro-mechanical-damage model were carried out to study the effects of low viscosity fluid pre-injection on pore pressure, stress field, and fracturing effect in tight heterogeneous glutenite reservoirs. The results indicate that the low viscosity fluid injection can effectively increase the pore pressure around the wellbore and reduce the effective stress of the glutenite. The FCI and SRV increase with the increase of the pre-injection amount of the low viscosity fluid. The HF complexity and SRV can be improved by pre-injecting low viscosity fluid to transform the in situ stress field. The field application of this technology in a well of Shengli Oilfield showed that low-viscosity fluid pre-injection can effectively increase the width of the fractured zone, improve the SRV, and optimize the fracturing effect.
相似文献6.
CO2 is now considered as a novel heat transmission fluid to extract geothermal energy. It can achieve the goal of energy exploitation and CO2 geological sequestration. Taking Zhacanggou as research area, a “Three-spot” well pattern (one injection with two production), “wellbore–reservoir” coupled model is built, and a constant injection rate is set up. A fully coupled wellbore–reservoir simulator—T2Well—is introduced to study the flow mechanism of CO2 working as heat transmission fluid, the variance pattern of each physical field, the influence of CO2 injection rate on heat extraction and the potential and sustainability of heat resource in Guide region. The density profile variance resulting from temperature differences of two wells can help the system achieve “self-circulation” by siphon phenomenon, which is more significant in higher injection rate cases. The density of CO2 is under the effect of both pressure and temperature; moreover, it has a counter effect on temperature and pressure. The feedback makes the flow process in wellbore more complex. In low injection rate scenarios, the temperature has a dominating impact on the fluid density, while in high rate scenario, pressure plays a more important role. In most scenarios, it basically keeps stable during 30-year operation. The decline of production temperature is <5 °C. However, for some high injection rate cases (75 and 100 kg/s), due to the heat depletion in reservoir, there is a dramatic decline for production temperature and heat extraction rate. Therefore, a 50-kg/s CO2 injection rate is more suitable for “Three-spot” well pattern in Guide region. 相似文献
7.
射孔作为井筒与储层之间的液流通道,是水力压裂过程中的重要可控性参数。为研究水平井射孔-近井筒破裂机制,采用岩层变形-流体渗流方程描述应力状态变化,应用连续损伤破裂单元表征三维破裂位置与形态演化,并开发有限元求解程序模拟分析了射孔对水平井初始破裂压力、破裂位置及近井筒裂缝复杂性的调控作用。通过与解析模型及射孔压裂物理模型试验结果对比,验证了模型及有限元程序的有效性;水平井破裂压力数值分析结果与现场测试数据吻合较好。研究表明：射孔可调控水平井破裂压力与初始破裂位置,同时对近井筒区域裂缝扩展形态影响显著。通过优化射孔参数可以引导初始破裂向最优破裂面扩展、有效降低破裂压力,减小由于螺旋射孔空间排布引起的水平井近井筒裂缝迂曲与复杂程度,提高致密油气藏压裂改造效果。 相似文献
8.
This paper proposes a pressure-monitoring method to warn any possible CO2 leakage by monitoring pressure change at the upper layer of storage reservoirs within injection wells. The monitoring method is tested with two problems under various scenarios. With a current pressure detection limit, the proposed pressure-monitoring technique can be widely applicable wherever a permeable upper formation exists above the CO2 storage reservoir and is effective even in offshore storage sites wherever conventional monitoring methods for onshore sites cannot be applied. Meanwhile, the method is limited to apply during injection and is subject to any possible pressure dampening. 相似文献
9.
A Study of Stress Change and Fault Slip in Producing Gas Reservoirs Overlain by Elastic and Viscoelastic Caprocks 总被引：3，自引：2，他引：1
Geomechanical simulations were conducted to study the effects of reservoir depletion on the stability of internal and boundary faults in gas reservoirs overlain by elastic and viscoelastic salt caprocks. The numerical models were of a disk-shaped gas reservoir with idealized geometry; they mimic the structure of a gas field in the northern Netherlands which has experienced induced seismicity during gas production. The geomechanical simulations identified the area of the internal fault most sensitive to fault reactivation as coinciding with the epicenters of the largest seismic events associated with gas production. Depletion-induced shear slip is initiated at the depth of the reservoir, in the fault areas where the vertical fault throw ranges between 0.5 and 1.5 times the reservoir thickness. The extent of reactivated area differs depending on whether the caprock is viscoelastic or elastic: when it is viscoelastic, there is more down-dip shear displacement. High initial horizontal stresses in the rock salt and lower stresses in the elastic side-seal and the reservoir promote unloading of the internal and reservoir-bounding faults even before the reservoir is depleted. Particularly prone to fault reactivation are the fault zones along the interface between the reservoir rock and the salt caprock, which may already be critically stressed before depletion and are likely to be reactivated early during gas production. Stress relaxation and associated geomechanical changes affecting fault stability and ground surface deformation may continue long after production has ceased, due to the viscous behavior of the salt. 相似文献
10.
The Geomechanics of CO2 Storage in Deep Sedimentary Formations 总被引：1，自引：0，他引：1
Jonny Rutqvist 《Geotechnical and Geological Engineering》2012,30(3):525-551
This paper provides a review of the geomechanics and modeling of geomechanics associated with geologic carbon storage (GCS), focusing on storage in deep sedimentary formations, in particular saline aquifers. The paper first introduces the concept of storage in deep sedimentary formations, the geomechanical processes and issues related with such an operation, and the relevant geomechanical modeling tools. This is followed by a more detailed review of geomechanical aspects, including reservoir stress-strain and microseismicity, well integrity, caprock sealing performance, and the potential for fault reactivation and notable (felt) seismic events. Geomechanical observations at current GCS field deployments, mainly at the In Salah CO2 storage project in Algeria, are also integrated into the review. The In Salah project, with its injection into a relatively thin, low-permeability sandstone is an excellent analogue to the saline aquifers that might be used for large scale GCS in parts of Northwest Europe, the U.S. Midwest, and China. Some of the lessons learned at In Salah related to geomechanics are discussed, including how monitoring of geomechanical responses is used for detecting subsurface geomechanical changes and tracking fluid movements, and how such monitoring and geomechanical analyses have led to preventative changes in the injection parameters. Recently, the importance of geomechanics has become more widely recognized among GCS stakeholders, especially with respect to the potential for triggering notable (felt) seismic events and how such events could impact the long-term integrity of a CO2 repository (as well as how it could impact the public perception of GCS). As described in the paper, to date, no notable seismic event has been reported from any of the current CO2 storage projects, although some unfelt microseismic activities have been detected by geophones. However, potential future commercial GCS operations from large power plants will require injection at a much larger scale. For such large-scale injections, a staged, learn-as-you-go approach is recommended, involving a gradual increase of injection rates combined with continuous monitoring of geomechanical changes, as well as siting beneath a multiple layered overburden for multiple flow barrier protection, should an unexpected deep fault reactivation occur. 相似文献
11.
Carbon dioxide (CO2) has been injected in the subsurface permeable formations as a means to cut atmospheric CO2 emissions and/or enhance oil recovery (EOR). It is important to constrain the boundaries of the CO2 plume in the target formation and/or other formations hosting the CO2 migrated from the target formation. Monitoring methods and technologies to assess the CO2 plume boundaries over time within a reservoir of interest are required. Previously introduced methods and technologies on pressure monitoring to detect the extent of the CO2 plume require at least two wells, i.e. pulser and observation wells. We introduce pressure transient technique requiring single well only. Single well pressure transient testing (drawdown/buildup/injection/falloff) is widely used to determine reservoir properties and wellbore conditions. Pressure diagnostic plots are used to identify different flow regimes and determine the reservoir/well characteristics. We propose a method to determine the plume extent for a constant rate pressure transient test at a single well outside the CO2 plume. Due to the significant contrast between mobility and storativity of the CO2 and native fluids (oil or brine), the CO2 boundary causes deviation in the pressure diagnostic response from that corresponding to previously identified heterogeneities. Using the superposition principle, we develop a relationship between the deviation time and the plume boundary. We demonstrate the applicability of the proposed method using numerically generated synthetic data corresponding to homogeneous, heterogeneous, and anisotropic cases to evaluate its potential and limitations. We discuss ways to identify and overcome the potential limitations for application of the method in the field. 相似文献
12.
直井开发煤层气钻井和压裂成本高,控制面积小,单井产气量低;煤层内水平井钻进难度大,风险高,薄煤层中井眼轨迹控制难度大,钻井液有害固相对储层伤害严重,采收率低。基于此,分析贵州织金区块煤系地质构造,提出在煤系地层内稳定的非储层内布水平井,通过压裂造缝沟通水平井上下煤层同时开发多层煤层的新思路。与常规开发方式相比,非储层内水平井具有钻井风险小、储层伤害小、单井产量高的优点,同时还可以开发煤系致密气和页岩气,提高非常规天然气利用率。研究非储层内水平井开发贵州织金煤层气技术,为解决贵州煤系地层煤层多而薄、层间距小等特性煤层气开发难题以及综合利用煤系气提供新的方式。 相似文献
13.
Leonhard Ganzer Viktor Reitenbach Dieter Pudlo Daniel Albrecht Arron Tchouka Singhe Kilian Nhungong Awemo Joachim Wienand Reinhard Gaupp 《Acta Geotechnica》2014,9(1):39-47
The feasibility of CO2 storage and enhanced gas recovery (EGR) effects in the mature Altmark natural gas field in Central Germany has been studied in this paper. The investigations were comprehensive and comprise the characterization of the litho- and diagenetic facies, mineral content, geochemical composition, the petrophysical properties of the reservoir rocks with respect to their potential reactivity to CO2 as well as reservoir simulation studies to evaluate the CO2 wellbore injectivity and displacement efficiency of the residual gas by the injected CO2. The Rotliegend sediments of the Altmark pilot injection area exhibit distinct mineralogical, geochemical, and petrophysical features related to litho- and diagenetic facies types. The reservoir rock reactivity to CO2 has been studied in autoclave experiments and associated effects on two-phase transport properties have been examined by means of routine and special core analysis before and after the laboratory runs. Dissolution of calcite and anhydrite during the short-term treatments leading to the enhancements of permeability and porosity as well as stabilization of the water saturation relevant for CO2 injection have been observed. Numerical simulation of the injection process and EGR effects in a sector of the Altmark field coupled with a wellbore model revealed the possibility of injecting the CO2 gas at temperatures as low as 10 °C and pressures around 40 bar achieving effective inflow in the reservoir without phase transition in the wellbore. The small ratio of injected CO2 volume versus reservoir volume indicated no significant EGR effects. However, the retention and storage capacity of CO2 will be maximized. The migration/extension of CO2 varies as a function of heterogeneity both in the layers and in the reservoir. The investigation of CO2 extension and pressure propagation suggested no breakthrough of CO2 at the prospective production well during the 3-year injection period studied. 相似文献
14.
The sensitivity of coal permeability to the effective stress means that changes in stress as well as pore pressure within a coal seam lead to changes in permeability. In addition coal swells with gas adsorption and shrinks with desorption; these sorption strains impact on the coal stress state and thus the permeability. Therefore the consideration of gas migration in coal requires an appreciation of the coupled geomechanical behaviour. A number of approaches to representing coal permeability incorporate the geomechanical response and have found widespread use in reservoir simulation. However these approaches are based on two simplifying assumptions; uniaxial strain (i.e. zero strain in the horizontal plane) and constant vertical stress. This paper investigates the accuracy of these assumptions for reservoir simulation of enhanced coalbed methane through CO2 sequestration. A coupled simulation approach is used where the coalbed methane simulator SIMED II is coupled with the geomechanical model FLAC3D. This model is applied to three simulation case studies assembled from information presented in the literature. Two of these are for 100% CO2 injection, while the final example is where a flue gas (12.5% CO2 and 87.5% N2) is injected. It was found that the horizontal contrast in sorption strain within the coal seam caused by spatial differences in the total gas content leads to vertical stress variation. Thus the permeability calculated from the coupled simulation and that using an existing coal permeability model, the Shi–Durucan model, are significantly different; for the region in the vicinity of the production well the coupled permeability is greater than the Shi–Durucan model. In the vicinity of the injection well the permeability is less than that calculated using the Shi–Durucan model. This response is a function of the magnitude of the strain contrast within the seam and dissipates as these contrasts diminish. 相似文献
15.
Numerical analysis of the effect of natural microcracks on the supercritical CO2 fracturing crack network of shale rock based on bonded particle models 
下载免费PDF全文
下载免费PDF全文 The problem of predicting the geometric structure of induced fractures is highly complex and significant in the fracturing stimulation of rock reservoirs. In the traditional continuous fracturing models, the mechanical properties of reservoir rock are input as macroscopic quantities. These models neglect the microcracks and discontinuous characteristics of rock, which are important factors influencing the geometric structure of the induced fractures. In this paper, we simulate supercritical CO2 fracturing based on the bonded particle model to investigate the effect of original natural microcracks on the induced‐fracture network distribution. The microcracks are simulated explicitly as broken bonds that form and coalesce into macroscopic fractures in the supercritical CO2 fracturing process. A calculation method for the distribution uniformity index (DUI) is proposed. The influence of the total number and DUI of initial microcracks on the mechanical properties of the rock sample is studied. The DUI of the induced fractures of supercritical CO2 fracturing and hydraulic fracturing for different DUIs of initial microcracks are compared, holding other conditions constant. The sensitivity of the DUI of the induced fractures to that of initial natural microcracks under different horizontal stress ratios is also probed. The numerical results indicate that the distribution of induced fractures of supercritical CO2 fracturing is more uniform than that of common hydraulic fracturing when the horizontal stress ratio is small. 相似文献
16.
Pouria Behnoud far Mohammad Javad Ameri Mostafa Orooji 《Arabian Journal of Geosciences》2017,10(18):397
Geomechanical changes may occur in reservoirs due to production from reservoirs. Study of these changes has an important role in upcoming operations. Frictional equilibrium is one of the items that should be determined during the depletion as it may vary with respect to time. Pre-existing faults and fractures will slide in regions where there is no frictional equilibrium. Hence, it may be concluded that reduction in pore pressure can initiate the sliding of faults. Whereas, it is also possible that faults will not exist after a certain time as production recovers the equilibrium. Casing shearing or lost circulation may be occurred due to faulting. In reservoirs which depletion leads to frictional equilibrium, decrease of fractures and faults leads to some variations in permeability. Hence, predicting the effect of depletion on frictional equilibrium is required in dealing with casing shearing or lost circulation in drilling of new wells. In addition, permeability modeling will be more precise during the life of reservoirs. Estimation of necessary time to create or vanish faults is vital to be successful in production from wells or drilling new wells. Achieving or loosing of equilibrium mainly depends on in situ stresses and rate of production. Estimation of the in situ stresses at the initiation state of reservoir is the key to study the state of faults. The next step is to predict the effects of depletion on in situ stresses. Different models are suggested in which decrease of horizontal stresses is predicted as function of pore pressure variation. In these models, different assumptions are made such as simplifying the poroelastic theory, ignoring the passing time, and considering the geometry of reservoir. In this article, a new model is proposed based on theory of inclusions and boundary element method. This state-of-the-art model considers the geometry of reservoir. In addition, changes of in situ are obtained as a function of time to reach to a more precise model capable of applying during the reservoir life. Finally, the model is imposed on real cases. The effect of depletion on faults is studied in reservoirs of normal and strike-slip stress regimes, and conventional and proposed models are compared. For this aim, in the first step, mechanical earth models of these two reservoirs are built using logging and coring data. Stress polygon method and poroelastic horizontal strain model are used for strike-slip and normal regimes, respectively. In reservoir 1 which is in a strike-slip stress regime, a fault is distinguished in formation microimaging (FMI) log. For this reservoir, the required time to achieve to frictional equilibrium is calculated. In the reservoir 2, the potential depth of fault sliding is analyzed and required time for faulting in that depth is predicted. The predicted time for satisfaction of frictional equilibrium using the proposed model has a significant difference with the predicted time using the previous methods. In addition, the proposed model predicts that different parts of reservoir 2 are willing for faulting during depletion. The previous model determines only one point that faulting may happen. It is necessary to use this new model to consider different important factors such as geometry and time to gain more accurate predictions. 相似文献
17.
This paper studied the CO2-EGR in Altmark natural gas field with numerical simulations. The hydro-mechanical coupled simulations were run using a linked simulator TOUGH2MP-FLAC3D. In order to consider the gas mixing process, EOS7C was implemented in TOUGH2MP. A multi-layered 3D model (4.4 km × 2 km × 1 km) which consists of the whole reservoir, caprock and base rock was generated based on a history-matched PETREL model, originally built by GDF SUEZ E&P Deutschland GmbH for Altmark natural gas field. The model is heterogeneous and discretized into 26,015 grid blocks. In the simulation, 100,000 t CO2 was injected in the reservoir through well S13 within 2 years, while gas was produced from the well S14. Some sensitivity analyses were also carried out. Simulation results show that CO2 tends to migrate toward the production well S14 along a NW–SE fault. It reached the observation wells S1 and S16 after 2 years, but no breakthrough occurred in the production well. After 2 years of CO2 injection, the reservoir pressure increased by 2.5 bar, which is beneficial for gas recovery. The largest uplift (1 mm) occurred at the bottom of the caprock. The deformation was small (elastic) and caprock integrity was not affected. With the injection rate doubled the average pressure increased by 5.3 bar. Even then the CO2 did not reach the production well S14 after 2 years of injection. It could be concluded that the previous flow field was established during the primary gas production history. This former flow field, including CO2 injection/CH4 production rate during CO2-EGR and fault directions and intensity are the most important factors affecting the CO2 transport. 相似文献
18.
Carbon dioxide injection and associated hydraulic fracturing of reservoir formations 总被引：2，自引：1，他引：1
The storage potential of subsurface geological systems makes them viable candidates for long-term disposal of significant quantities of CO2. The geo-mechanical responses of these systems as a result of injection processes as well as the protracted storage of CO2 are aspects that require sufficient understanding. A hypothetical model has been developed that conceptualises a typical well-reservoir system comprising an injection well where the fluid (CO2) is introduced and a production/abandoned well sited at a distant location. This was accomplished by adopting a numerical methodology (discrete element method), specifically designed to investigate the geo-mechanical phenomena whereby the various processes are monitored at the inter-particle scale. Fracturing events were simulated. In addition, the influence of certain operating variables such as injection flow rate and fluid pressure was studied with particular interest in the nature of occurring fractures and trend of propagation, the pattern and magnitude of pressure build-up at the well vicinity, pressure distribution between well regions and pore velocity distribution between well regions. Modelling results generally show an initiation of fracturing caused by tensile failure of the rock material at the region of fluid injection; however, fracturing caused by shear failure becomes more dominant at the later stage of injection. Furthermore, isolated fracturing events were observed to occur at the production/abandoned wells that were not propagated from the injection point. This highlights the potential of CO2 introduced through an injection well, which could be used to enhance oil/gas recovery at a distant production well. The rate and magnitude of fracture development are directly influenced by the fluid injection rate. Likewise, the magnitude of pressure build-up is greatly affected by the fluid injection rate and the distance from the point of injection. The DEM modelling technique illustrated provides an effective procedure that allows for more specific investigations of geo-mechanical mechanisms occurring at subsurface systems. The application of this methodology to the injection and storage of CO2 facilitates the understanding of the fracturing phenomenon as well as the various factors governing the process. 相似文献
19.
Analysis of refracturing in horizontal wells: Insights from the poroelastic displacement discontinuity method 下载免费PDF全文
下载免费PDF全文 Ali Rezaei Giorgio Bornia Mehdi Rafiee Mohamed Soliman Stephen Morse 《国际地质力学数值与分析法杂志》2018,42(11):1306-1327
In this paper, a fully coupled 2‐dimensional poroelastic displacement discontinuity method is used to investigate the refracturing process in horizontal wells. One of the objectives of refracturing is to access new reserves by adding new hydraulic fractures in zones that were bypassed in the initial fracturing attempt. Pore pressure depletion in the vicinity of old fractures directly affects the state of stress and eventually the propagation of newly created hydraulic fractures. Thus, a poroelastic analysis is required to identify guidelines for the refracturing process, in particular to understand the extension of the pore pressure depletion, and eventually, the orientation of new as well as old fractures. We propose a fully coupled approach to model the whole process of child fracture propagation in a depleted area between 2 parent fractures in the same wellbore. This approach omits the need of using multistep workflow that is regularly used to model the process. The maximum tensile stress criterion (σ criterion) is used for hydraulic fracture propagation. The proposed method is verified using available analytical solutions for total stress and pore pressure loading modes on a line fracture in drained and undrained conditions. Then, test cases of multifractured horizontal wells are studied to calculate the time evolution of the stress and pore pressure fields around old fractures and to understand the effect of these fields on the propagation path of newly created fractures. Finally, the effect of the pore pressure depletion on the propagation path of the newly created fractures in the bypassed area of the same wellbore is studied. The results show that the depleted areas around old fractures are highly affected by the extent and severity of the stress redistribution and pore pressure depletion. It is observed that a successful creation of new fractures may only happen in certain time frames. The results of this study provide new insights on the behavior of newly created fractures in depleted zones. They also clarify the relationship between stress change and pore pressure depletion in horizontal wells. 相似文献