首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献，搜索用时 15 毫秒
1.
In order to better constrain the interpretation and the nature of the seismic reflectors, experimental measurements at high confining pressure (up to 300 MPa) and room temperature of the compressional wave velocity (Vp) on 10 samples representative of the most common lithologies along the Aurina (Ahrntal), Tures (Tauferer Tal), and Badia (Abtei Tal) Valleys profile (Eastern Alps, Italy) have been performed. For each sample, the speed of ultrasonic waves was measured in three mutually perpendicular directions, parallel and normal to the rock foliation and lineation.The main results are:(a) Good agreement between the calculated vs. measured modal compositions of the considered rocks, indicating that they were presumably equilibrated at the estimated P–T conditions; therefore, the seismic properties are representative of the crustal level indicated by the thermobarometry.(b) Measured and calculated average Vp are in good agreement, and are typical of mid-crustal level (6.0–6.5 km/s). Only the amphibolites show Vp typical of the lower crust (7.2 km/s).(c) The seismic anisotropy of metapelites is very high (12–27%), both with orthorhombic and transverse isotropy symmetry; amphibolites are transversely isotropic with an anisotropy of 8%; orthogneisses and granitoids are isotropic or weakly anisotropic.(d) The contacts between amphibolites and all other rock types may generate good reflections, provided they are not steeply inclined. Although the metamorphic foliation remains steeply inclined, discordant buried sub-horizontal igneous contacts may be detected.  相似文献   

2.
Shear deformation in calcite-rich rocks can produce strong lattice preferred orientations (LPO), which result in a high anisotropy of bulk seismic properties because of the high elastic anisotropy of calcite (32% Vp anisotropy). Deformed rocks often show also strong shape preferred orientations (SPO). Theories for averaging the elastic properties have not yet satisfactorily predicted the contribution to the seismic anisotropy caused by the SPO alone.A calcite mylonite from Carrara (Italy) was investigated, which is characterised by a strong SPO and a weak LPO. It was composed of about 80% calcite, then white mica, quartz and hematite. Flattening of mica and of calcite grains defined the mylonitic foliation, and elongation of calcite grains defined the lineation. On average calcite grains have aspect ratios of about 2.5:1.6:1, and grain sizes of about 10 μm. At 400 MPa confining pressure, the measured Vp (km/s) parallel to the lineation (X direction) was highest (6.63), lower in the intermediate Y direction (6.47); the Vp normal to the foliation (Z direction) was lowest (6.30). This yielded a Vp anisotropy of 5%. The LPO, determined by automated electron backscatter diffraction (EBSD), was very weak (texture index 1.1), with intensities between 0.6 and 1.6 m.r.d. in the c-axis pole figure. Extrapolation of the texture index to an infinite number of orientation measurements indicated that the observed variations were mostly random noise in the orientation distributions and that the bulk rock texture was random. The Vp anisotropy of the Voigt, Reuss and Hill averages calculated from this calcite LPO is predicted to be close to zero. Adding 5% of muscovite with (001) perfectly aligned parallel to the foliation, we calculated a total anisotropy of 2.8%. The anisotropy calculated for the special directions X, Y and Z remained at 2.6% only.It was concluded that the measured seismic anisotropy cannot be explained by the LPO of calcite and by 5% of mica alone. It is also attributed to the strong SPO and to further grain boundary effects.  相似文献   

3.
We have measured P- and S-wave velocities on two amphibolite and two gneiss samples from the Kola superdeep borehole as a function of pressure (up to 600 MPa) and temperature (up to 600 °C). The velocity measurements include compressional (Vp) and shear wave velocities (Vs1, Vs2) propagating in three orthogonal directions which were in general not parallel to inherent rock symmetry axes or planes. The measurements are accompanied by 3D-velocities calculations based on lattice preferred orientation (LPO) obtained by TOF (Time Of Flight) neutron diffraction analysis which allows the investigation of bulk volumes up to several cubic centimetres due to the high penetration depth of neutrons. The LPO-based numerical velocity calculations give important information on the different contribution of the various rock-forming minerals to bulk elastic anisotropy and on the relations of seismic anisotropy, shear wave splitting, and shear wave polarization to the structural reference frame (foliation and lineation). Comparison with measured velocities obtained for the three propagation directions that were not in accordance with the structural frame of the rocks (foliation and lineation) demonstrate that for shear waves propagating through anisotropic rocks the vibration directions are as important as the propagation directions. The study demonstrates that proper measurement of shear wave splitting by means of two orthogonal polarized sending and receiving shear wave transducers is only possible when their propagation and polarization directions are parallel and normal to foliation and lineation, respectively.  相似文献   

4.
Chlorite peridotites from Almklovdalen in southwest Norway were studied to understand the deformation processes and seismic anisotropy in the upper mantle. The lattice preferred orientation (LPO) of olivine and chlorite was determined using electron backscattered diffraction (EBSD)/scanning electron microscopy. A sample with abundant garnet showed [100] axes of olivine aligned sub-parallel to lineation, and [010] axes aligned subnormal to foliation: A-type LPO. Samples rich in chlorite showed different olivine LPOs. Two samples showed [001] axes aligned sub-parallel to lineation, and [010] axes aligned subnormal to foliation: B-type LPO. Two other samples showed [100] axes aligned sub-parallel to lineation, and [001] axes aligned subnormal to foliation: E-type LPO. Chlorite showed a strong LPO characterized by [001] axes aligned subnormal to foliation with a weak girdle subnormal to lineation. Fourier transform infrared (FTIR) spectroscopy of the specimens revealed that the olivines with A-type LPO contain a small amount (170 ppm H/Si) of water. In contrast, the olivines with B-type LPOs contain a large amount (340 ppm H/Si) of water.

The seismic anisotropy of the olivine and chlorite was calculated. Olivine showed Vp anisotropy of up to 3.8% and a maximum Vs anisotropy of up to 2.7%. However, the chlorite showed a much stronger Vp anisotropy, up to 21.1%, and a maximum Vs anisotropy of up to 31.7%. A sample with a mixture of 25% of olivine and 75% of chlorite can produce a Vp anisotropy of 14.2% and a maximum Vs anisotropy of 22.9%. Because chlorite has a wide stability field at high pressure and high temperature in the subduction zone, the strong LPO of chlorite can be a source of the observed trench-normal or trench-parallel seismic anisotropy in the mantle wedge as well as in subducting slabs depending on the dipping angle of slab in a subduction zone where chlorite is stable.  相似文献   

5.
Automated electron backscattered diffraction (EBSD) was applied using a scanning electron microscope to obtain lattice preferred orientation (LPO) data for olivine in garnet peridotites of the Central Alps. As a reference frame, the LPOs of enstatite were also investigated. In the garnet peridotite at Cima di Gagnone (CDG), a weak foliation carrying a distinct lineation is present. The lineation is characterized by elongated enstatite, olivine and poikiloblastic garnet. Olivine shows a very unusual LPO with [100] normal to foliation and [001] parallel to lineation. Achsenverteilungsanalyse (AVA) maps demonstrate that [001] of olivine grains corresponds quite well to their maximum length axes which are preferentially parallel to the lineation. Numerous planar hydrous defects within (001) planes of olivine are marked by palisades of ilmenite rods and show a preferred orientation normal to lineation. Calculated P-wave velocities for CDG are fastest (8.32 km sу) normal to foliation with a relatively low anisotropy (2.9%). Compared to mantle peridotites with the usual (010)[100] LPO where the fastest Vp direction is towards the lineation, the relationship between flow geometry and seismic anisotropy is significantly different at CDG. Several mechanisms for the formation of the LPO type at CDG are considered, with glide possible on (100)[001] of olivine. On the basis of field data as well as petrographic and petrologic evidence, it has been demonstrated that the CDG garnet peridotite formed by prograde metamorphism from a hydrous protolith at pressures and temperatures of about 3.0 GPa and 750 °C, respectively. The CDG LPO is interpreted to have formed during hydrous subduction zone metamorphism. The same interpretation may hold for the previously investigated olivine LPO at Alpe Arami, which is similar to that at the nearby CDG. The observed anomalous LPO is no proof for ultradeep (>3.0 GPa) conditions.  相似文献   

6.
The Ibituruna quartz-syenite was emplaced as a sill in the Ribeira-Araçuaí Neoproterozoic belt (Southeastern Brazil) during the last stages of the Gondwana supercontinent amalgamation. We have measured the Anisotropy of Magnetic Susceptibility (AMS) in samples from the Ibituruna sill to unravel its magnetic fabric that is regarded as a proxy for its magmatic fabric. A large magnetic anisotropy, dominantly due to magnetite, and a consistent magnetic fabric have been determined over the entire Ibituruna massif. The magmatic foliation and lineation are strikingly parallel to the solid-state mylonitic foliation and lineation measured in the country-rock. Altogether, these observations suggest that the Ibituruna sill was emplaced during the high temperature (~ 750 °C) regional deformation and was deformed before full solidification coherently with its country-rock. Unexpectedly, geochronological data suggest a rather different conclusion. LA-ICP-MS and SHRIMP ages of zircons from the Ibituruna quartz-syenite are in the range 530–535 Ma and LA-ICP-MS ages of zircons and monazites from synkinematic leucocratic veins in the country-rocks suggest a crystallization at ~ 570–580 Ma, i.e., an HT deformation > 35My older than the emplacement of the Ibituruna quartz-syenite. Conclusions from the structural and the geochronological studies are therefore conflicting. A possible explanation arises from 40Ar–39Ar thermochronology. We have dated amphiboles from the quartz-syenite, and amphiboles and biotites from the country-rock. Together with the ages of monazites and zircons in the country-rock, 40Ar–39Ar mineral ages suggest a very low cooling rate: < 3 °C/My between 570 and ~ 500 Ma and ~ 5 °C/My between 500 and 460 Ma. Assuming a protracted regional deformation consistent over tens of My, under such stable thermal conditions the fabric and microstructure of deformed rocks may remain almost unchanged even if they underwent and recorded strain pulses separated by long periods of time. This may be a characteristic of slow cooling “hot orogens” that rocks deformed at significantly different periods during the orogeny, but under roughly unchanged temperature conditions, may display almost indiscernible microstructure and fabric.  相似文献   

7.
Two different Pan-African tectono-metamorphic events are recognised in the Taita Hill Tsavo East National Park/Galana river area, SE-Kenya (Mozambique belt) based on petrographic and geothermobarometric evidence. Structurally, this area can be subdivided into four units: (1) the easternmost part of the basement along the Galana river is characterized by subhorizontal slightly to the west and east dipping foliation planes. Migmatic paragneisses with intercalated marbles, calcsilicates and metapelites and bands of amphibolites are the dominant rock type. (2) The western part of the Galana river within the Tsavo East National Park is a ca. 25 km wide shear zone with subvertical foliation planes. The eastern part shows similar rocks as observed in unit 1, while towards west, metasedimentary units become rare and the main rock types are tonalitic gneisses with intercalated amphibolites. (3) A 10 km wide zone (Sagala Hills zone) between the strike slip zone (unit 2) and the Taita Hills (unit 4) is developed. This zone is characterized by elongated and folded felsic migmatic amphibole and garnet bearing orthogneiss bodies with intercalated bands of mafic rocks. (4) The Taita Hills are a slightly to the N dipping nappe stack. The main rock type in the Taita Hills are amphibole–biotite–plagioclase–quartz ± garnet ± clinopyroxene ± scapolite bearing migmatic gneisses with mafic bands. In the southern part, metapelites, marbles and some amphibolites are common.Although the geological structures are different in units 1 and 2, the calculated PT conditions are similar with peak PT of 760–820 °C and 7.5–9.5 kbar. Temperatures in unit 3 (Sagalla Hills zone) and unit 4 (Taita Hills) are slightly higher ca. 760–840 °C, but pressure is significantly higher, ranging from 10 to 12 kbar. Sillimanite growth around kyanite, garnet zonation pattern, mineral reaction textures, and PT calculations constrain a “clock-wise” PT-path with near isobaric cooling following the peak of metamorphism. The different PT conditions, tectonic setting, and a different age of metamorphism are evidence that units 1 and 2 (Galana river) belong to a different tectono-metamorphic event than unit 3 (Sagala Hills zone) and 4 (Taita Hills). The major shear zone (unit 2) marks a tectonic suture dividing the two different tectono-metamorphic domains. It is also likely that it played an important role during exhumation of the granulite facies rocks from units 3 and 4.  相似文献   

8.
The ratio of P- to S-wave velocities (Vp/Vs) is regarded as one of the most diagnostic properties of natural rocks. It has been used as a discriminant of composition for the continental crust and provides valuable constraints on its formation and evolution processes. Furthermore, the spatial and temporal changes in Vp/Vs before and after earthquakes are probably the most promising avenue to understanding the source mechanics and possibly predicting earthquakes. Here we calibrate the variations in Vp/Vs in dry, anisotropic crustal rocks and provide a set of basic information for the interpretation of future seismic data from the Wenchuan earthquake Fault zone Scientific Drilling (WFSD) project and other surveys. Vp/Vs is a constant (φ0) for an isotropic rock. However, most of crustal rocks are anisotropic due to lattice-preferred orientations of anisotropic minerals (e.g., mica, amphibole, plagioclase and pyroxene) and cracks as well as thin compositional layering. The Vp/Vs ratio of an anisotropic rock measured along a selected pair of propagation-vibration directions is an apparent value (φij) that is significantly different from the value for its isotropic counterpart (φ0). The usefulness of apparent Vp/Vs ratios as a diagnostic of crustal composition depends largely on rock seismic anisotropy. A 5% of P- and S-wave velocity anisotropy is sufficient to make it impossible to determine the crustal composition using the conventional criteria (Vp/Vs<1.756 for felsic rocks, 1.756l.944 fluid-tidied porous/fractured or partially molten rocks) if the information about the wave propagation-polarization directions with respect to the tectonic framework is unknown. However, the variations in Vp/Vs measured from borehole seismic experiments can be readily interpreted according to the orientations of the ray path and the polarization of the shear waves with respect to the present-day principal stress directions (I.e., the orientation of cracks) and the frozen fabric (I.e., foliation and lineation).  相似文献   

9.
The lattice preferred orientation (LPO) of an anorthosite (composed of andesine) sampled from a highly deformed anorthositic mylonite (Grenville Province, Quebec) was measured by TOF neutron diffraction and SEM-EBSD. The quantitative texture analysis of neutron data was accomplished by using the Rietveld texture analysis with the WIMV algorithm, implemented in the program package Materials Analysis Using Diffraction (MAUD). The texture calculations of the EBSD data were performed by using the program BEARTEX. Analyses from neutron and electron diffraction data gave similar results if EBSD data are smoothed to account for grain statistics. The principal pole figures show (010) roughly parallel to the rock foliation, (001) poles exhibiting a low angle (25°) to the pole to foliation, and (100) poles close to the Y-direction (perpendicular to the lineation and foliation pole). The [100] crystallographic direction shows a maximum in the lineation direction, [010] directions concentrate near the foliation pole. The geological deformation conditions and the constructed pole figure patterns indicate that the preferred orientation could be attributed to intracrystalline slip dominantly on (010) with [100] as slip direction. Elastic properties, calculated by averaging, document weak anisotropy that has implications for the seismic structure of the lower crust.  相似文献   

10.
The 5158-m-deep main borehole of the Chinese Continental Scientific Drilling Project (CCSD-MH) penetrated granitic gneisses, paragneisses, eclogites, retrograde eclogites, amphibolites and ultramafic rocks in the Sulu ultrahigh-pressure (UHP) metamorphic terrane, eastern China. The CCSD-MH consists of four petro-structural units separated by three SE-dipping ductile shear zones DFa (835-1280 m), DFb (2010-2280 m) and DFc (2920-3225 m), which are correspondent with the regional shear zones in the northern Sulu UHP supracrustal zone. Using the electron backscatter diffraction (EBSD) technique, we investigated the lattice-preferred orientations (LPOs) of omphacite, diopside and quartz in core samples from the CCSD-MH. Omphacite from eclogites and diopside from garnet pyroxenites display very strong LPOs, which are characterized by the maximum concentration of [001]-axes parallel to the lineation and (010)-poles normal to the foliation. Quartz in para- and granitic mylonites/gneisses from the shear zones DFa, DFb and DFc developed multiple slip systems. 40Ar/39Ar dating of biotite in para- and granitic gneisses from the CCSD-MH yields 223-202 Ma, which constrains the formation ages of the quartz high-temperature prism slip systems {m}<a> and {m}[c]. The asymmetric LPOs of omphacite, diopside, olivine and quartz with respect to the structural frame reveal three deformation phases in the Sulu terrane. In the Middle Triassic, the northward subduction of the Yangtze plate to depths > 100 km produced a top-to-the-south shear sense in LPOs of omphacite, diopside and olivine, and a nearly N-S-striking foliation and a subhorizontal N-S-trending lineation in eclogites and ultramafic rocks. In the Late Triassic, the UHP rocks were exhumed to the lower crust and quartz developed high-temperature slip systems with a top-to-the-NW shear sense, which is consistent with the regional SE-dipping foliation and SE-plunging lineation in the ductile shear zones. In the Cretaceous the UHP rocks were exhumed to the middle crust when the migmatization and granitic intrusion formed a NE-striking antiform structure. As a result, the activation of quartz low-temperature basal slip (0001)<a> is characterized by a top-to-the-SE shear sense in the south, but a top-to-the-NW shear sense in the north.  相似文献   

11.
Lattice-preferred orientations (LPO) of olivine, diopside, enstatite and garnet from the Zhimafang garnet peridotite body in the Sulu ultrahigh-pressure (UHP) metamorphic terrane (China) were measured using the electron backscatter diffraction (EBSD) technique. The peridotite was captured from a mantle wedge immediately adjacent the subducted Yangtze slab and then experienced the UHP metamorphism at 750–950 °C and 4–7 GPa. The olivine LPO is characterized by the [001] axis close to the stretching lineation and the (100) plane subparallel to the foliation, indicating the prevailing of (100) [001] slip. Enstatite LPO displays the dominance of (100) [001] slip. Diopside developed complex LPO patterns that are difficult to explain using a single slip system of (100) [001]. Garnet is almost randomly oriented due to its low volume fractions, cubic symmetry and the presence of numerous slip systems. Calculated seismic properties of the peridotite yield a maximum P-wave velocity normal to the foliation and a minimum along the foliation, with anisotropy up to 8% in strongly sheared samples. The S-wave velocity pattern is complex but the fast polarization plane generally normal to the foliation. The inferred shear sense from the olivine LPO is top-to-SE, in contrary to exhumation-induced top-to-NW thrusting recorded in the quartz LPO, implying that the olivine LPO formed at early UHP metamorphic conditions. The olivine crystals have relatively low water contents (141–475 H/106 Si), indicating a fluid-deficient environment for the LPO formation. The present study suggests that a combination of low temperature and UHP plays a much more important role than the water content to promote the activation of (100) [001] slip in olivine.  相似文献   

12.
Multi-equilibrium thermobarometry shows that low-grade metapelites (Cubito-Moura schists) from the Ossa–Morena Zone underwent HP–LT metamorphism from 340–370 °C at 1.0–0.9 GPa to 400–450 °C at 0.8–0.7 GPa. These HP–LT equilibriums were reached by parageneses including white K mica, chlorite and chloritoid, which define the earliest schistosity (S1) in these rocks. The main foliation in the schists is a crenulation cleavage (S2), which developed during decompression from 0.8–0.7 to 0.4–0.3 GPa at increasing temperatures from 400–450 °C to 440–465 °C. Fe3+ in chlorite decreased greatly during prograde metamorphism from molar fractions of 0.4 determined in syn-S1 chlorites down to 0.1 in syn-S2 chlorites. These new data add to previous findings of eclogites in the Moura schists indicating that a pile of allochtonous rocks situated next to the Beja-Acebuches oceanic amphibolites underwent HP–LT metamorphism during the Variscan orogeny. To cite this article: G. Booth-Rea et al., C. R. Geoscience 338 (2006).  相似文献   

13.
M. Faccenda  G. Bressan  L. Burlini   《Tectonophysics》2007,445(3-4):210-226
The compressional and shear wave velocities have been measured at room temperature and pressure up to 450 MPa on 5 sedimentary rock samples, representative of the most common lithologies of the upper crust in the central Friuli area (northeastern Italy). At 400 MPa confining pressure the Triassic dolomitic rock shows the highest velocities (Vp  7 km/s, Vs  3.6 km/s), the Jurassic and Triassic limestones samples intermediate velocities (Vp  6.3 /s, Vs  3.5 km/s) and the Cenozoic and Paleozoic sandstones the lowest velocities (Vp  6.15 km/s, Vs  3.35 km/s). The Paleozoic sandstone sample is characterized by the strongest anisotropy (10%) and significant birefringence (0.2 km/s) is found only on the Cenozoic sandstone sample. We elaborated the synthetic profiles of seismic velocities, density, elastic parameters and reflection coefficient, related to 4 one-dimensional geological models extended up to 22 km depth. The synthetic profiles evidence high rheological contrasts between Triassic dolomitic rocks and the soft sandstones and the Jurassic limestones. The Vp profiles obtained from laboratory measurements match very well the in-situ Vp profile measured by sonic log for the limestones and dolomitic rocks, supporting our one-dimensional modelling of the calcareous-carbonatic stratigraphic series. The Vp and Vs values of the synthetic profiles are compared with the corresponding ones obtained from the 3-D tomographic inversion of local earthquakes. The laboratory Vp are generally higher than the tomographic ones with major discrepancies for the dolomitic lithology. The comparison with the depth location of seismicity reveals that the seismic energy is mainly released in correspondence of high-contrast rheological boundaries.  相似文献   

14.
Seismic anisotropy in the upper mantle provides important constraints on mantle dynamics, continental evolution and global tectonics and is believed to be produced by the flow-induced lattice-preferred orientation (LPO) of olivine. Recent experimental studies at high pressure and temperature have suggested that the LPO of olivine is affected by pressure in addition to water and stress. However, there has been no report yet for the pressure-induced LPO of natural olivine because samples from the deep upper mantle are rare and often unsuitable for study due to ambiguous foliation and lineation. Here we show evidence of the pressure-induced LPO of natural olivine in diamond-bearing garnet peridotites from Finsch, South Africa. We found that the [010] axes of olivine are aligned subnormal to foliation and that the [001] axes are aligned subparallel to lineation, which is known as B-type LPO of olivine. The equilibrium pressure of the samples, as estimated using geobarometer, was greater than 4 GPa, indicating that the samples originated from a depth greater than ∼120 km. In addition, FTIR spectroscopy of the olivine showed that the samples are dry, with a water content of less than 90 ± 20 ppm H/Si (5.5 ± 1.2 ppm wt. H2O). These data suggest that the samples are the first natural examples of olivine displaying B-type LPOs produced due to high pressure under dry condition. Our data indicate that the trench-parallel seismic anisotropy observed in many subduction zones in and below subducting slabs at depths greater than ∼90 km under dry condition may be attributed to the pressure-induced olivine fabrics (B-type LPO) and may be interpreted as the entrainment of the sub-lithospheric mantle in the direction of subduction rather than anomalous trench-parallel flow.  相似文献   

15.
In this work, we report the results of combined geological, structural, and anisotropy of magnetic susceptibility (AMS) studies carried out on Quaternary deposits in the Picentini Mountains, southern Apennines (Italy). The study concerns four small continental basins, Acerno, Tizzano, Iumaiano, and Piano del Gaudo, related to fluvial–lacustrine depositional environments, ranging in altitude from 600 to 1,200 m a.s.l. and strongly incised during recent time. Stratigraphic and structural analyses, integrated by low- and high-field anisotropy of magnetic susceptibility (AMS), show that the formation of these basins has been controlled by extensional and transtensional tectonics. Most of the AMS sites exhibit a well-defined magnetic foliation parallel to the bedding planes. A well-defined magnetic lineation has also been measured within the foliation planes. In the Iumaiano, Tizzano, and Piano del Gaudo basins, magnetic lineations cluster around NNE–SSW trend and are parallel to the stretching directions inferred by structural analysis of faults and fractures. On the basis of structural, sedimentological, and high-field AMS data, we suggest a tectonic origin for the magnetic lineation, analogously to what has been observed in other weakly deformed sediments from Neogene and Quaternary extensional basins of the Mediterranean region. Our results demonstrate that onset and the evolution of the investigated basins have been mainly controlled since lower Pleistocene by NW–SE normal and transtensional faults. This deformation pattern is consistent with a prevalent NE–SW extensional tectonic regime, still active in southern Apennines, as revealed by seismological and geodetic data.  相似文献   

16.
This paper describes quartz ribbons parallel to foliation, containing elongate recrystallized quartz grains aligned oblique to the foliation within a mylonite of the southern Tasman Belt, southeastern Australia. The shape fabric of quartz grains varies in obliquity (with respect to the foliation) and intensity (grain aspect ratio) from one ribbon to another, whereas the c-axis fabric pattern is stable with respect to the mylonitic foliation and lineation. It is argued that the grain shape fabric is an oscillating foliation due to competition between deformation and syntectonic recrystallization.  相似文献   

17.
三维参照变形及应变相研究评述   总被引：2，自引：0，他引：2  
三维参照变形和应变相是最近构造地质学领域中取得的重要进展,三维参照变形是理想化的三维变形分类,每一参照变形是共轴级分（拉伸、压扁或纯剪）和与其垂直的简单切组分同时作用的产物,三种可能的面理取向和三种可能的线理取向的不同组合构成六咱应变相,三维参照变形和应变相研究证明糜陵面理未必平行剪切带,可与剪切带斜交,甚至垂直,线理未必与剪切方向一致,可与剪切方向斜交,甚至垂直,出现横向面理时,剪切指向标志位于该面理内,出现横向线理时,剪切指向出现在与线理垂直的ａｃ面理内,三维变形分析不公可解决三维分析难以解释的横向面理和线理,而且可确定共轴组分的类型及其与单剪组分的结合方式。  相似文献   

18.
In the high-grade Moldanubian Zone of the European Variscides, numerous bodies of ultramafic rocks occur embedded in granulite. The anisotropy of magnetic susceptibility and its low-field variation as well as the anisotropy of magnetic remanence were used to investigate magnetic fabrics of some ultramafic bodies and host granulite. In granulite, the magnetic foliation is roughly parallel to the metamorphic foliation and the magnetic lineation is near the mineral alignment lineation. In ultramafite, the magnetic foliation is relatively scattered spatially, but mostly oriented in a different way than that in granulite. The magnetic lineation is also scattered, but still relatively well defined spatially. Again, its orientation is mostly different than that of granulite. The magnetic fabric in ultramafic rocks is therefore different from that in the host granulite even though both rock types underwent at least partially common structural history. The componental movements forming the granulite fabric, mostly during amphibolite facies retrograde metamorphism, were evidently not intensive enough to strongly overprint the magnetic fabric of ultramafite. The ultramafite is therefore strong enough to maintain its pre-metamorphism fabric even at such high temperatures and pressures that are characteristic of high amphibolite facies retrograde metamorphism.  相似文献   

19.
Jean-Philippe Bellot   《Tectonophysics》2008,449(1-4):133-144
The role of fluids in the deformation of continental serpentinites is investigated from structural, microstructural and petrographic analyses applied to a km-scale porphyroclast mantled in a viscous matrix of amphibolites. The clast is sited within a shear zone of the Palaeozoic Maures massif, France. Syntectonic fluid–rock interactions occurred from km to mm scales, at first on the clast borders (along the main rheological boundaries) then within the clast. They are accommodated macroscopically by slickenfibers faults and microscopically by shear microcracks within crack-seal veins, typifying an intermediate, brittle–ductile behaviour of serpentinites. Three main stages of deformation–serpentinisation processes occurred in relation with the left-lateral movement of the hosted shear zone. They developed under metamorphic conditions evolving from amphibolites to green-schists facies conditions ( 400 MPa/550 °C to  200 MPa/< 300 °C), as inferred from the surrounding sheared amphibolites. Deformation and serpentinisation increase through time although fluid pressure decreases. If the shape of the inclusion and its orientation relative to the shear zone mainly controlled the deformation pattern though time (P then R' shears), fluid pressure is required for starting deformation–serpentinisation processes along inherited anisotropy planes. Whatever the origin of fluids, they play a key role all along the deformation processes by influencing stress states within the shear zone at the onset of deformation and by changing at various scales and through time behaviour of the rock, depending of the intensity of serpentinisation and the rate of deformation.  相似文献   

20.
本文对藏东昌都地区侏罗纪汪布组、东大桥组和小索卡组红层共71个采点开展了磁组构(AMS)研究。磁组构测试结果表明,早侏罗世汪布组岩石磁线理较磁面理发育,磁化率各向异性度较高,磁化率椭球最小轴K3散布于层面缩短方向,代表了与构造成因相关的磁组构;中侏罗世东大桥组和晚侏罗世小索卡组岩石则磁面理较磁线理发育,磁化率各向异性度较低,磁化率椭球最小轴K3与层面近垂直,指示了原生沉积磁组构。早侏罗世汪布组地层的磁组构揭示了其构造应力场方向为NE-SW向。中侏罗世东大桥组的磁组构指示了其沉积时的古水流方向为SE向(138.3°),而晚侏罗世小索卡组磁组构指示了其沉积时的古水流方向为NNW向(328.3°)。古水流方向的明显变化揭示了昌都地区从中侏罗世到晚侏罗世沉积物物源发生了相应的转变,表明昌都地区南早北晚的隆升过程。  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号