首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献，搜索用时 437 毫秒
1.
This paper presents an efficient procedure to determine the natural frequencies, modal damping ratios and mode shapes for torsionally coupled shear buildings using earthquake response records. It is shown that the responses recorded at the top and first floor levels are sufficient to identify the dominant modal properties of a multistoried torsionally coupled shear building with uniform mass and constant eccentricity even when the input excitation is not known. The procedure applies eigenrealization algorithm to generate the state‐space model of the structure using the cross‐correlations among the measured responses. The dynamic characteristics of the structure are determined from the state‐space realization matrices. Since the mode shapes are obtained only at the instrumented floor (top and first floors) levels, a new mode shape interpolation technique has been proposed to estimate the mode shape coefficients at the remaining floor levels. The application of the procedure has been demonstrated through a numerical experiment on an eight‐storied torsionally coupled shear building subjected to earthquake base excitation. The results show that the proposed parameter identification technique is capable of identifying dominant modal parameters and responses even with significant noise contamination of the response records. Copyright © 2008 John Wiley & Sons, Ltd.  相似文献   

2.
为了验证提出的新型筒式自复位形状记忆合金阻尼器(telescopic recentering shape memory al-loy damper,TRSMAD)对结构平动-扭转耦联振动反应的抑制作用,进行了偏心结构消能减震体系的振动台试验。设计了一个1/4缩尺的三层两跨单向偏心的钢框架模型,将提出的新型SMA阻尼器安装在结构底层的一侧,通过振动台分别对无控条件下和装有阻尼器的有控条件下的结构反应进行了研究。试验结果表明:(1)在各地震波作用下,TRSMAD对结构的平动反应有很好控制效果,而对结构各层扭转角位移的控制效果稍低;(2)不同地震波下的控制效果有所不同:对结构的平动位移而言,天津波的减震率最高,El Centro波次之,最后为Taft波;对结构扭转角的控制,平均而言,除了天津波作用下第二层为特例外,对El Centro波的减震效果最好,其次为Taft波,最后为天津波;(3)同一地震波下,阻尼器对结构模型一层的位移控制效果较其他层为优。  相似文献   

3.
A new floor connecting system developed for low‐damage seismic‐resistant building structures is described herein. The system, termed Inertial Force‐Limiting Floor Anchorage System (IFAS), is intended to limit the lateral forces in buildings during an earthquake. This objective is accomplished by providing limited‐strength deformable connections between the floor system and the primary elements of the lateral force‐resisting system. The connections transform the seismic demands from inertial forces into relative displacements between the floors and lateral force‐resisting system. This paper presents the IFAS performance in a shake‐table testing program that provides a direct comparison with an equivalent conventional rigidly anchored‐floor structure. The test structure is a half‐scale, 4‐story reinforced concrete flat‐plate shear wall structure. Precast hybrid rocking walls and special precast columns were used for test repeatability in a 22‐input strong ground‐motion sequence. The structure was purposely designed with an eccentric wall layout to examine the performance of the system in coupled translational‐torsional response. The test results indicated a seismic demand reduction in the lateral force‐resisting system of the IFAS structure relative to the conventional structure, including reduced shear wall base rotation, shear wall and column inter‐story drift, and, in some cases, floor accelerations. These results indicate the potential for the IFAS to minimize damage to the primary structural and non‐structural components during earthquakes.  相似文献   

4.
选择美国加州大学圣地亚哥分校7层钢筋混凝土剪力墙足尺结构振动台实验,开展结构损伤识别研究,实验采用白噪声、环境振动和不同强度的地震动交替激发,记录地震动激发实验前后的结构反应。基于该记录计算和对比自振频率和振型曲率的变化、剪切波走时及其变化和结构层间位移角,分析发现一层和二层振型曲率较大,走时较长,走时变化也较大,现场检查发现一层和二层的破坏也较为严重,这些参数可用于识别结构损伤程度和定位损伤位置,而自振频率和层间位移角变化仅可反映出结构损伤程度,难以揭示结构损伤位置。  相似文献   

5.
不对称大底板多塔楼隔震结构的地震响应分析   总被引：1，自引：0，他引：1  
党育  杜永峰 《地震学刊》2012,(4):452-458
针对不对称大底板多塔楼隔震结构体系,通过建立地震响应的动力分析简化模型,推导出不对称大底板多塔楼隔震结构体系地震作用下的运动方程。对一实际的不对称大底板多塔楼隔震结构进行地震响应仿真分析,探讨塔楼质量偏心率和塔楼质量比对结构周期比、位移比和层剪力比的影响。结果显示,不对称大底板多塔楼隔震结构扭转角主要由隔震层产生;与不隔震结构相比,不对称大底板多塔楼隔震体系的扭转角减小,可取得较好的减震效果;塔楼与底板的位置分布和质量分布会影响体系的扭转效应和减震效果,应尽量使塔楼的质心与底板质心重合,塔楼质量分布均匀,以减小结构的扭转效应,提高减震效果。  相似文献   

6.
This paper presents the development of a deformable connection that is used to connect each floor system of the flexible gravity load resisting system (GLRS) with the stiff lateral force resisting system (LFRS) of an earthquake‐resistant building. It is shown that the deformable connection acts as a seismic response modification device, which limits the lateral forces transferred from each floor to the LFRS and allows relative motion between the GLRS and LFRS. In addition, the floor accelerations and the LFRS story shears related to the higher‐mode responses are reduced. The dispersion of peak responses is also significantly reduced. Numerical simulations of the earthquake response of a 12‐story reinforced concrete shear wall example building with deformable connections are used to define an approximate feasible design space for the deformable connection. The responses of the example building model with deformable connections and the example building model with rigid‐elastic connections are compared. Two configurations of the deformable connection are studied. In one configuration, a buckling restrained brace is used as the limited‐strength load‐carrying hysteretic component of the deformable connection, and in the other configuration, a friction device is used. Low damping laminated rubber bearings are used in both configurations to ensure the out‐of‐plane stability of the LFRS and to provide post‐elastic stiffness to the deformable connection. Important experimental results from full‐scale tests of the deformable connections are presented and used to calibrate numerical models of the connections. Copyright © 2016 John Wiley & Sons, Ltd.  相似文献   

7.
大多数建筑结构由梁、柱、支撑、剪力墙、地基和楼板等主要结构组成。一般而言,楼板对建筑结构的抗震性能可以忽略不计,所以进行建筑结构分析的模型是无楼板的。因此,楼板被刚性隔板代替,以提高分析效率。本文提出的建筑结构抗震分析解析模型考虑了楼板抗弯刚度,该模型采用超级单元、刚性隔板和子结构技术来减少自由度。通过实例分析,验证了该模型在多层建筑结构抗震分析中的有效性和准确性。且此模型能够显著减少计算量,提高分析效率,振动周期和响应时间等分析结果的精度与精化模型的结果非常接近,说明该模型的提出是合理的。  相似文献   

8.
Response of asymmetric buildup under earthquake excitation often involves lateral vibration coupled with torsional vibration. Floor slab is, in general, assumed as rigid along the in‐plane direction. Building code provisions to account for the torsional effect in static force procedure are based on centre of rigidity or shear centre of the building. A convenient procedure is developed here to locate the centre of rigidity or shear centre, which can be implemented, using any standard building analysis software. The procedure is applicable for orthogonal as well as non‐orthogonal building systems and accounts for all possible definitions of static eccentricity to compute the design response. An irregular building is analysed to illustrate the proposed methodology. Significant variation in member force resultants is observed due to different definitions of static eccentricity. Finally, a mathematical proof is presented to substantiate the applicability of the proposed procedure to a non‐orthogonal building. Copyright © 2006 John Wiley & Sons, Ltd.  相似文献   

9.
The differences between the increase in building response due to accidental eccentricity predicted by code-specified static and dynamic analyses are studied for symmetric and unsymmetric single and multistorey buildings. The increase in response computed from static analysis of the building is obtained by applying the equivalent static forces at distance ea, equal to the storey accidental eccentricity, from the centre of mass at each floor. Alternatively, this increase in response is computed by dynamic analysis of the building with the centre of mass of each floor shifted through a distance ea from its nominal position. A parametric study is performed on single-storey systems in order to evaluate the differences in response predicted by both analysis procedures. It is shown that these results are essentially the same as the ones obtained for a special class of multistorey systems. Upper and lower bounds for the differences in response computed from static and dynamic analyses are obtained for general multistorey systems. These differences in response depend primarily on the ratio of the fundamental torsional and lateral frequencies of the building. They are larger for small values of the frequency ratio and decrease to zero as the frequency ratio becomes large. Further, these discrepancies are in many cases of the same order as the code-intended increase in response due to accidental eccentricity. This implies that the code-specified static and dynamic analyses to account for accidental torsion should be modified to be mutually consistent.  相似文献   

10.
This paper proposes a model‐based state observer to perform high‐definition response estimation in partially instrumented building structures. The proposed estimator is verified in a simulated five‐story shear‐building structure and validated using measurements from a seven‐story reinforced concrete building slice tested at the NEES‐University of California at San Diego shake table. In both cases the proposed estimator yielded satisfactory results by estimating the time history of shear forces, bending moments, displacements, and strains at various points/sections of interest. The proposed algorithm can be used in instrumented buildings for various practical applications such as post‐earthquake damage assessment, structural control, and building code calibration. Copyright © 2016 John Wiley & Sons, Ltd.  相似文献   

11.
This paper investigates numerically the seismic response of six seismically base‐isolated (BI) 20‐story reinforced concrete buildings and compares their response to that of a fixed‐base (FB) building with a similar structural system above ground. Located in Berkeley, California, 2 km from the Hayward fault, the buildings are designed with a core wall that provides most of the lateral force resistance above ground. For the BI buildings, the following are investigated: two isolation systems (both implemented below a three‐story basement), isolation periods equal to 4, 5, and 6 s, and two levels of flexural strength of the wall. The first isolation system combines tension‐resistant friction pendulum bearings and nonlinear fluid viscous dampers (NFVDs); the second combines low‐friction tension‐resistant crosslinear bearings, lead‐rubber bearings, and NFVDs. The designs of all buildings satisfy ASCE 7‐10 requirements, except that one component of horizontal excitation, is used in the 2D nonlinear response history analysis. Analysis is performed for a set of ground motions scaled to the design earthquake and to the maximum considered earthquake (MCE). At both the design earthquake and the MCE, the FB building develops large inelastic deformations and shear forces in the wall and large floor accelerations. At the MCE, four of the BI buildings experience nominally elastic response of the wall, with floor accelerations and shear forces being 0.25 to 0.55 times those experienced by the FB building. The response of the FB and four of the BI buildings to four unscaled historical pulse‐like near‐fault ground motions is also studied. Copyright © 2013 John Wiley & Sons, Ltd.  相似文献   

12.
带SRC桁架转换层及钢加强层高层建筑抗震性能研究   总被引：6，自引：2，他引：4  
本文对一座设置钢骨混凝土桁架转换层及两道钢桁架加强层的超高层建筑结构模型振动台试验结果进行了分析,发现Ⅶ度小震和中震阶段在下部转换层和中部加强层加速度突变较大,而上部加强层突变较小：在Ⅶ度大震阶段由于转换层及其附近楼层裂缝的出现,地震能量转嫁到中部加强层,致使中部加强层加速度突变出现大幅度的增长,该层及附近楼层核心筒墙肢出现一定程度的破坏。采用SAP2000有限元程序对该结构模型进行了小震阶段三维分析,并与试验值进行了对比：从动力特性来看,前几阶周期比较吻合,高阶周期误差较大;从动力反应来看,侧移曲线、加速度包络图、地震作用包络图在整体上符合较好,但在中部加强层和转换层处突变幅度计算值偏小;从层间剪力包络图来看,试验值与有限元计算值都呈现近似直线分布。  相似文献   

13.
A new concept for the earthquake resistant design of timber shear wall structures is proposed. By providing friction devices in the corners of the framing system of the shear wall, its earthquake resistance and damage control potential can be enhanced considerably. During severe earthquake excitations, the friction devices slip and a large portion of the seismic energy input is dissipated by friction rather than by inelastic deformation of the sheathing-to-framing connectors. A simple numerical model is developed and results of inelastic time-history dynamic analyses show the superior performance of the friction damped timber shear walls compared to conventional shear wall systems. The proposed friction devices act both as safety valves by limiting the inertia forces transmitted to the structure, and as structural dampers by dissipating a significant portion of the seismic energy input. The devices can be used in any configuration of the framing system to accommodate architectural or construction requirements. The damping system may also be conveniently incorporated in existing timber shear wall buildings to upgrade significantly their earthquake resistance.  相似文献   

14.
An ensemble of earthquake records is used to carry out non-linear analyses of simple torsionally unbalanced systems considering both resisting elements and earthquake components along two perpendicular directions. These fully bidirectional analyses are focused to study the effect of the following factors: (i) seismic-force reduction factor; (ii) factors α and δ used to compute the design eccentricity; (iii) initial lateral period; and (iv) initial stiffness eccentricity. Results indicate that the amplification factor α can be specified as a function of the force reduction factor, the lateral uncoupled period, and the stiffness eccentricity. It is concluded that the coefficient δ depends on the lateral period, the stiffness eccentricity, and the geometrical eccentricity. It was observed that negative shears caused by torsion should be neglected in the design of the stiff element, particularly in the case of systems with large stiffness eccentricity. Results suggest that additional studies should be performed to verify the assumed (partial) equivalence between unidirectional (resisting elements and earthquake components along one direction only) and fully bidirectional analyses to study building torsion problems. Copyright © 1999 John Wiley & Sons, Ltd.  相似文献   

15.
We apply a combination of earthquake early warning system (EEWS) and real-time strong motion monitoring system (RSMS) to emergency response for a high-rise building; The Kogakuin University has a 29-story high-rise building in Shinjuku Ward, Tokyo. The proposed strategy is based on the Plan, Do, Check, Action (PDCA) Cycle to brush up the systems and the users: in the “Plan” stage, we apply EEWS and RSMS to the building, where EEWS predicts not only short-period strong ground motions but also long-period ground motions [1]. The system is built into a building announcement system, an emergency elevator control system, and an email message system, which quickly send emails to the emergency response team. Meanwhile, RSMS provides information on seismic intensities at each floor of the building via the web browser in real time using the existing network in the building. In addition, the building response and structural damage can be estimated based on this information. The network system is impervious to the earthquake damage, because the network cable has extra length, there is, however, possible that a network system does not work due to power outage. Thus, we develop the network system that has uninterruptible power-supply system (UPS) and apply it to EEWS and RSMS. The high-rise building has the emergency call units to the security control center in the building on every floor. The emergency call line, however, will be busy promptly, because it is able to use only one line. Therefore, we installed IP telephone which uses the network system on main floors. UPS will work about 30 min after a major earthquake, it is supposed to be enough time for gathering the damage information about the building during initial response. In the “Do” stage, we prepare emergency response instruction manuals and educate the faculty members and students to carry out promptly emergency response. In the “Check” stage, the validity of the proposed systems are verified by carrying out an earthquake drill in an actual high-rise building. The earthquake drill confirmed that our proposed approach is valid. In the final “Action” stage, we improve these systems and emergency response manual and educate people in the building how to use effectively these systems.  相似文献   

16.
Post-earthquake damages investigation in past and recent earthquakes has illustrated that the building structures are vulnerable to severe damage and/or collapse during moderate to strong ground motion. Among the possible structural damages, seismic induced pounding has been commonly observed in several earthquakes. A parametric study on buildings pounding response as well as proper seismic hazard mitigation practice for adjacent buildings is carried out. Three categories of recorded earthquake excitation are used for input excitations. The effect of impact is studied using linear and nonlinear contact force model for different separation distances and compared with nominal model without pounding consideration. The severity of the impact depends on the dynamic characteristics of the adjacent buildings in combination with the earthquake characteristics. Pounding produces acceleration and shear forces/stresses at various story levels that are greater than those obtained from the no pounding case, while the peak drift depends on the input excitation characteristics. Also, increasing gap width is likely to be effective when the separation is sufficiently wide to eliminate contact. Furthermore, it is effective to provide a shock absorber device system for the mitigation of impact effects between adjacent buildings with relatively narrow seismic gaps, where the sudden changes of stiffness during poundings can be smoothed. This prevents, to some extent, the acceleration peaks due to impact. The pounding forces exerted on the adjacent buildings can be satisfactorily reduced.  相似文献   

17.
This paper presents a detailed study on feasibility of un‐bonded fiber reinforced elastomeric isolator (U‐FREI) as an alternative to steel reinforced elastomeric isolator (SREI) for seismic isolation of un‐reinforced masonry buildings. Un‐reinforced masonry buildings are inherently vulnerable under seismic excitation, and U‐FREIs are used for seismic isolation of such buildings in the present study. Shake table testing of a base isolated two storey un‐reinforced masonry building model subjected to four prescribed input excitations is carried out to ascertain its effectiveness in controlling seismic response. To compare the performance of U‐FREI, same building is placed directly on the shake table without isolator, and fixed base (FB) condition is simulated by restraining the base of the building with the shake table. Dynamic response characteristic of base isolated (BI) masonry building subjected to different intensities of input earthquakes is compared with the response of the same building without base isolation system. Acceleration response amplification and peak response values of test model with and without base isolation system are compared for different intensities of table acceleration. Distribution of shear forces and moment along the height of the structure and response time histories indicates significant reduction of dynamic responses of the structure with U‐FREI system. This study clearly demonstrates the improved seismic performance of un‐reinforced masonry building model supported on U‐FREIs under the action of considered ground motions. Copyright © 2015 John Wiley & Sons, Ltd.  相似文献   

18.
This paper presents the results from shaking table tests of a one-tenth-scale reinforced concrete (RC) building model. The test model is a protype of a building that was seriously damaged during the 1985 Mexico earthquake. The input ground excitation used during the test was from the records obtained near the site of the prototype building during the 1985 and 1995 Mexico earthquakes. The tests showed that the damage pattern of the test model agreed well with that of the prototype building. Analytical prediction of earthquake response has been conducted for the prototype building using a sophisticated 3-D frame model. The input motion used for the dynamic analysis was the shaking table test measurements with similarity transformation. The comparison of the analytical results and the shaking table test results indicates that the response of the RC building to minor and the moderate earthquakes can be predicated well. However, there is difference between the predication and the actual response to the major earthquake.  相似文献   

19.
The use of collision shear walls (bumper‐type), acting transversely to the side subject to pounding, as a measure to minimize damage of reinforced concrete buildings in contact, is investigated using 5‐story building models. The buildings were designed according to the Greek anti‐seismic and reinforced concrete design codes. Owing to story height differences potential pounding in case of an earthquake will occur between floor slabs, a case specifically chosen because this is when pounding can turn out to be catastrophic. The investigation is carried out using nonlinear dynamic analyses for a real earthquake motion and also a simplified solution for a triangular dynamic force of short duration, comparable to the forces caused by pounding. For such analyses, nonlinear, prismatic beam–column elements are used and the effects of pounding are expressed in terms of changes in rotational ductility factors of the building elements. The local effects of pounding on the collision shear walls are investigated using a detailed nonlinear finite element model of the shear walls and results are expressed in terms of induced stresses. It is found that pounding will cause instantaneous acceleration pulses in the colliding buildings and will somewhat increase ductility demands in the members of the top floor, but all within tolerable limits. At the same time the collision walls will suffer repairable local damage at the points of contact, but will effectively protect both buildings from collapse, which could occur if columns were in the place of the walls. Copyright © 2008 John Wiley & Sons, Ltd.  相似文献   

20.
Earthquake dynamic response analysis of large complex structures, especially in the presence of nonlinearities, usually turns out to be computationally expensive. In this paper, the methodical developments of a new model order reduction strategy (MOR) based on the proper orthogonal decomposition (POD) method as well as its practical applicability to a realistic building structure are presented. The seismic performance of the building structure, a medical complex, is to be improved by means of base isolation realized by frictional pendulum bearings. According to the new introduced MOR strategy, a set of deterministic POD modes (transformation matrix) is assembled, which is derived based on the information of parts of the response history, so‐called snapshots, of the structure under a representative earthquake excitation. Subsequently, this transformation matrix is utilized to create reduced‐order models of the structure subjected to different earthquake excitations. These sets of nonlinear low‐order representations are now solved in a fractional amount of time in comparison with the computations of the full (non‐reduced) systems. The results demonstrate accurate approximations of the physical (full) responses by means of this new MOR strategy if the probable behavior of the structure has already been captured in the POD snapshots. Copyright © 2016 The Authors. Earthquake Engineering & Structural Dynamics Published by John Wiley & Sons Ltd.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号