共查询到17条相似文献，搜索用时 147 毫秒
1.
为探究脆塑性转化带断层的力学性质和滑动稳定性,本文采用干燥的Carrara大理岩预切断层(saw-cut)样品,在气体介质三轴高温岩石力学实验仪上开展了摩擦实验研究,实验温度70～400℃,围压30～100 MPa,位移速率在0.08μm·s-1, 0.4μm·s-1, 2μm·s-1之间切换.实验力学数据揭示,不同围压下Carrara大理岩断层摩擦系数随温度变化规律不同：低围压(30 MPa)下,摩擦系数随温度升高先增大后减小,中高围压(≥70 MPa)下摩擦系数则表现为随温度先减小后增大.断层摩擦滑动行为在100～300℃的范围内表现出由稳定的速度强化转化为不稳定的速度弱化,且在400℃左右重新转变为稳定的速度强化.实验后断层滑动面形貌和微观结构分析表明,稳定滑动断层面为高反射镜面,擦痕清晰;黏滑断层面为有光泽的凹凸不平的表面;最高围压下蠕滑的断层面粗糙无光泽,擦痕不可辨别.本文认为受温度激活的塑性变形过程逐步主导了岩石变形,对断层激活发生不稳定滑动至关重要,而高围压则会抑制断层的不稳定滑动.本研究结果不仅为识别野外... 相似文献
2.
野外、实验和地震数据表明:浅部地壳的变形以脆性破裂为主,深部地壳的变形以晶体塑性流动为主.在这种认识的基础上,提出了地壳变形的2种机制模型,即发生脆性变形的上部地壳强度基于Byerlee摩擦定律以及发生塑性变形的下部地壳强度基于幂次蠕变定律.而位于其间的脆塑性转化带的深度与浅源地震深度的下限具有很好的一致性.然而,二元结构的流变模型局限性在于其力学模型过于简单,往往过高估计了脆塑性转化带的强度.问题的根源在于对脆塑性转化带的变形机制的研究已有很多,但没有定量的力学方程来描述脆塑性转化带强度;而且以往对断层脆塑性转化带的研究主要集中在温度引起的脆塑性转化方面,对因应变速率和流体对脆塑性转化的影响方面的研究也比较薄弱.对断层带内矿物变形机制研究表明,某些断层带脆塑性转化发生在相同深度(温度和压力)内,发生脆塑性转化的原因是应变速率的变化,而这种变化被认为与地震周期的同震、震后-间震期蠕变有关,这种变化得到了主震-余震深度分布变化的证实.对断层流体特征分析表明,断层带内可能存在高压流体,这种高压流体会随断裂带的破裂及愈合而周期性变化,在地震孕育及循环中起着关键性作用.高压流体的形成(裂隙愈合)有多种机理,其中,压溶是断层带裂隙愈合的主导机制之一.研究在水作用下的压溶,可以对传统的摩擦-流变二元地壳强度结构及其断层强度进行补充与修正.通过以上分析,认为有必要通过野外变形样品和高温高压实验,深入研究应变速率及流体压力对断层脆塑性转化的影响,同时,通过实验建立压溶蠕变的方程,近似地估计脆塑性转化带的强度. 相似文献
3.
玄武岩作为大洋地壳上的主要成分,研究其摩擦特性是更好地探究逆冲板块边界上大地震等力学行为机理的基础.为了研究少量橄榄石矿物是否会影响玄武岩的摩擦特性,本研究选用了国际大洋钻探计划(IODP)349航次获取的玄武岩样品,其中含有少量的橄榄石矿物.本次研究的实验温度范围为100～600℃,施加的有效正压力和孔隙水压分别为150 MPa和100 MPa.实验中玄武岩样品在300～400℃的温度条件下表现出不稳定的准静态震荡现象,并且在高温条件下(T>400℃)其剪切强度表现出显著的位移弱化现象,即摩擦系数随着剪切位移的进行而持续减小.在3 mm的剪切位移范围内,摩擦系数的变化范围为0.7～0.55.通过初步的微观剪切变形研究,我们推测橄榄石在摩擦实验过程中对一种弱矿物的生成可能起到了催化作用,但生成的弱矿物含量不足以显著地弱化断层泥的摩擦强度.同时微观构造分析也发现,随着温度的升高,断层泥的剪切构造由局部剪切向整体弥散性剪切变形转变,同时伴随着孔隙度的显著降低,因此我们认为剪切强度的位移弱化现象与流体参与下的颗粒间的压溶过程的逐步增强有关. 相似文献
4.
汶川地震发震断层为高角度逆断层,这种断层滑动和发生强震需要断层深部具备特殊的力学条件。发震断层地区地表出露若干韧性剪切带,其中不同类型石英变形具有不同的变形温度。细粒糜棱岩中的石英表现为高温位错蠕变,变形温度为500~700℃;含残斑初糜棱岩中的石英表现为中温位错蠕变,其变形温度为400~500℃;早期石英脉中的石英表现为低温位错蠕变,变形温度为280~400℃;晚期石英脉以碎裂变形为主,其变形温度为150~250℃。石英的这些变形特征显示出断层带经历了多期脆-塑性转化。根据糜棱岩中的重结晶石英的粒度估计的断层塑性流动应力为15~80MPa。石英和长石内的微量水以晶体缺陷水、颗粒边界水和流体包裹体水的形式存在,水含量随岩石的应变增加而升高,变化范围为0.01~0.15wt%。断层脆-塑性转化带内石英含有大量与裂隙愈合相关的次生流体包裹体,其捕获温度为330~350℃,流体压力为70~405MPa,估计的流体压力系数为0.16~0.9,代表强震发生后,断层带内产生的大量微裂隙逐渐愈合过程中的流体特征。在考虑断层带流体压力和应变速率变化条件下,利用石英流变参数建立了从间震期到地震成核阶段断层脆-塑性转化带流变结构和震后快速蠕滑阶段断层脆-塑性转化带流变结构。结果表明,在间震期、地震成核阶段、震后快速滑动阶段,断层强度和脆-塑性转化深度随应变速率和流体压力变化而变化,且脆-塑性转化特征与石英的变形机制、断层速度弱化和强化转化深度、汶川地震震源深度等吻合,显示映秀-北川断层具备摩擦滑动速度弱化和地震成核的基础,而断层带内存在高压流体可能是触发高角度逆断层滑动和汶川地震发生的主要机制。 相似文献
5.
为探索断层岩石摩擦特性对于断层力学性质的影响,我们采集了龙门山汶茂断裂韧性剪切带中的富含层状硅酸盐矿物的糜棱岩样品进行了水热条件下摩擦滑动实验研究.实验在三轴压机之上完成,实验温度为100~600℃,有效正压力100MPa,孔隙水压分别为30MPa和130MPa.为获得摩擦滑动的稳定性参数(a-b),剪切滑移速率在1.22μm·s-1,0.244μm·s-1和0.0488μm·s-1之间切换.实验发现在200~500℃的温度范围内,摩擦系数随着温度的增加而显著增大(约0.56~0.72).在200~300℃范围内,随温度的升高糜棱岩的摩擦滑动表现出由稳定的速度强化向不稳定速度弱化转变的趋势.在有效正压力不变的情况下,孔隙水压的增大会促进糜棱岩的摩擦滑动在500~600℃温度范围内由不稳定的速度弱化向稳定的速度强化的转变.实验给出的断层在原地深度处的脆性和塑性变形机制的转变,有助于理解断层深部的地震成核机制以及成核的温压条件. 相似文献
6.
7.
大量研究表明,流体在断层弱化中起着非常重要的作用.在地壳浅部脆性域,自由水通过流体孔隙压力减小断层有效正压力,从而降低断层摩擦强度;在地壳深部,矿物中的微量结构水弱化岩石流变强度.另外,流体-岩石相互作用等化学过程,如长石水解反应,对断层强度的影响也非常显著.断层深部流体通过物理作用与化学作用影响着岩石的变形机制,从而影响断层力学性质与地震孕育和发生.断层内部流体孔隙压力周期性变化是断层带脆-塑性转化、裂缝张开与愈合等的直接体现,这种变化控制着断层强度与强震周期性发生现象. 相似文献
8.
《地震地质》2020,(1)
地震精定位结果显示,大陆地震多数集中于大陆地壳的多震层内,该多震层向下收敛于中部地壳的脆塑性转化带。地壳脆塑性转化带的主要成分为花岗质岩石,前人通常用石英-斜长石的组合代替花岗岩进行变形研究,反演转化带的深度和变形特征,并且认为花岗岩的变形强度由弱项矿物——石英的塑性变形控制。近年来,实验和野外研究均表明钾长石的变形强度高于石英和斜长石。大应变量变形实验和野外韧性剪切带的研究结果显示,在中地壳脆塑性转化带内,钾长石变形以脆性破裂为主,斜长石和石英通常表现为动态重结晶。因此,用石英和斜长石的组合体代替花岗岩来反演断层的变形特征,无法全面、真实地解释断层深部脆塑性转化带的变形特征。文中总结了花岗岩在野外和实验变形条件下的研究结果,并分析了花岗岩的主要组成矿物——石英、斜长石和钾长石的变形特征以及其温压条件的不同步性,讨论了断层深部脆塑性转化带的失稳条件。 相似文献
9.
研究表明 ,干的基性下地壳处于半脆性摩擦与半脆性流变的过渡状态 ,因此 ,文中采用多种基性岩样品进行了干的和含水基性岩的脆塑性转化实验 ,以深入理解大陆下地壳的力学性质。实验围压 4 5 0～ 5 0 0MPa ,应变速率 1× 1 0 - 4s- 1。实验结果表明 ,济南辉长岩 (样品C)、延庆辉绿岩 (样品D)和含水辉绿岩从 30 0℃到 90 0℃经历了脆性破裂、碎裂流动、半脆性流动和塑性流动几个变形域 ,而细粒攀枝花辉长岩 (样品A)和中细粒攀枝花辉长岩 (样品B)从 70 0℃到 90 0℃经历了半脆性流动和塑性流动 2个变形域。干的辉长岩样品比干的辉绿岩样品发生脆延性转化的温度高 1 0 0℃ ;所有干的基性岩样品的脆塑性转化都发生在 70 0℃ ,但半脆性流动域变形微观结构有差别 ,辉绿岩中斜长石和辉石发生了细粒化 ,并存在强烈的定向 ,形成初糜棱岩结构 ,辉长岩样品的细粒化和定向特征不明显。干的基性岩在以位错滑移为主的高温塑性流变域的强度和微观结构基本相同。水对基性岩脆塑性转化的影响体现在岩石的强度和脆延性与脆塑性的转化温度两方面。在实验温度范围内 ,含水辉绿岩样品的强度远小于干的辉绿岩和辉长 相似文献
10.
为了探讨大陆地壳断层深部的力学性质,我们选择了采自红河断裂带的糜棱岩作为实验样品,进行热水条件下的高温高压摩擦滑动实验.实验在一个以气体为介质的高温高压三轴实验系统中进行.实验条件是：有效正应力为200 MPa;孔隙水压为30 MPa（在400 ℃到600 ℃之间为超临界水条件）;温度为100 ℃到600 ℃;轴向加载的速率范围从0.04 μm/s到0.2 μm/s再到1 μm/s.实验结果表明：（1）当温度小于300 ℃时,糜棱岩的摩擦强度随着温度的上升而增大;当温度大于300 ℃时,糜棱岩的摩擦强度随着温度的上升而减小.这种趋势和以往花岗岩的摩擦滑动数据基本一致;（2）糜棱岩在200 ℃和400 ℃时表现为速度弱化,其余温度下为速度强化;（3）糜棱岩与已有花岗岩的摩擦滑动数据并不完全一致;（4）花岗质糜棱岩速度弱化向速度强化转变的温度在430 ℃附近,以此我们可以推测：在变形机制为摩擦滑动的深部条件下,地震成核的深度范围可以比以往的估计更深. 相似文献
11.
蒙脱石的脱水作用对断层摩擦本构行为的影响 总被引：4，自引：3，他引：4
利用高温双轴摩擦装置，研究了含蒙脱石的断层带在不同温度下摩擦滑动的速度依赖性，以期了解脱水作用对摩擦行为的影响。结果表明，断层带摩擦强度随温度而升高，而速度依赖性较为复杂，以１．４ｕ／ｓ为界，室温和１００℃时，低滑动速率下表现为微弱的速度弱化，高滑动速率下则表现为速度强化；２００℃时均为速度强化；３００℃时高滑动速率下仍为速度强化，但低滑动速率下转变为速度弱化；４００℃以上，均为明显的速度弱化。摩擦行为的变化与脱水过程及相应的断层物质变形方式的变化密切相关 相似文献
12.
FRICTIONAL SLIDING OF PLAGIOCLASE GOUGE UNDER LOWER-CRUST TEMPERATURE AND RELATIVELY LOW EFFECTIVE NORMAL STRESS 
下载免费PDF全文
下载免费PDF全文 The discovery of tremors on the lower crust portion of the San Andreas Fault has attracted more attention on the mechanical properties of the lower crust in recent years, and some experimental studies have been carried out to understand the mechanical behavior. Previous experiments under effective normal stresses of 200MPa have shown that pyroxene and plagioclase mineral separated from the gabbro and their mixtures all show velocity weakening in the lower-crust temperature range, which results in unstable slip when frictional sliding is the dominant deformation mechanism. This work is to examine whether the velocity-weakening behavior of plagioclase gouge also applies to relatively lower effective normal stress. Our experiments were performed under effective normal stress of about 100MPa, with a constant confining pressure control, with pore pressure of 30MPa and temperature of 100℃ to 600℃. We found that the frictional sliding of plagioclase are basically the same with the previous results obtained under effective normal stress of 200MPa, both of which show velocity weakening over the entire temperature range. The only difference is the out-of-trend drop of constitutive parameter a at 600℃ for the lower effective normal stress of 100MPa. It is thus concluded that reducing the effective normal stress has little effect on the sliding stability of plagioclase, and the previous conclusion made for mechanical behavior of the lower crust that unstable slips are possible therein also applies to the lower effective normal stress of 100MPa. 相似文献
13.
EXPERIMENTAL STUDY ON THE EFFECT OF WATER ON THE STRENGTH AND DEFORMATION MECHANISM OF CARRARA MARBLE AT HIGH TEMPERATURE 下载免费PDF全文
下载免费PDF全文 We performed deformation experiments using Carrara marble in dry and wet conditions under temperature of 400~700℃ and confining pressure 300MPa with two different strain rates. Water contents of deformed samples were measured using FTIR spectroscopy. The microstructure and deformation mechanisms of samples were observed under optical microscopy, scanning electron microscopy and energy spectroscopy analysis. The mechanical data show that samples display strain hardening at 400℃, and transition to steady creep at temperature from 500~700℃. The strength of marble reduced gradually with elevated temperatures or decreased strain rate. However, water effect to the strength of the marble is significantly weak. Microstructures observed show that the deformation is cataclastic flow in dry samples, fracture and pressure solution in wet samples at 400℃. Samples underwent brittle-plastic transition at 500℃. Dislocation glide is major deformation mechanism for dry samples at 600℃. Dislocation climb and dynamic recrystallization are major deformation mechanism for wet samples at 600℃ and for all wet samples and dry samples at 700℃. Lower strain rate and higher water content could promote the process of pressure solution and diffusion as well as dynamic recrystallization. 相似文献
14.
为了深入理解断层带摩擦滑动速度依赖性转换及其机制,利用双轴摩擦实验对干燥及含水条件下岩盐断层带摩擦的速度依赖性进行了实验研究,并观测了摩擦滑动过程中的声发射,分析了断层带的微观结构.实验结果表明,干燥岩盐断层带在0.1~100 μm/s的速度范围内表现为速度弱化,增大σ2会使断层带向速度强化转变;含水条件下岩盐断层带在1~100 μm/s的速度范围内表现为速度弱化,而在0.1~0.01 μm/s的速度范围内表现为速度强化,速度依赖性转换出现在0.1~1 μm/s,其中断层表现为振荡或应力释放时间较长的黏滑事件;岩盐断层带在干燥条件下表现出很强的声发射活动,每个黏滑均对应一丛声发射事件,而在含水条件下一次黏滑只对应一个声发射事件.显微观察表明,局部化的脆性破裂是速度弱化域的主要变形机制,分布式的碎裂流动是干燥岩盐断层带在速度强化域的变形机制,颗粒边界迁移以及压溶作用的塑性变形是含水条件下岩盐断层带在速度强化域的主要变形机制,而脆性破裂和塑性变形共同控制着速度依赖性转换域断层带的变形.水的存在促进岩盐发生塑性变形,进而导致断层带从速度弱化向速度强化转换.上述结果有助于理解断层带上地震活动的特征和慢地震的机制. 相似文献
15.
断层带摩擦稳定性转换及其对应的微破裂特征对于地震成核条件和慢地震机理研究具有重要的意义.本文利用双轴实验装置研究了硬石膏断层带摩擦稳定性的转换及其对应的应变变化、微破裂特征,并分析了实验标本的微观结构.实验结果表明,σ2和加载点速度对断层滑动稳定性具有显著影响.在低σ2条件下,硬石膏断层带出现不稳定滑动,变形以局部化的脆性破裂和摩擦为主;随σ2的增加,断层由不稳定滑动向稳定滑动转换,断层带变形方式逐渐转变为分布式的破裂.在低σ2条件下,硬石膏断层带在较低加载点速度下表现为速度强化且滑动稳定,在中等加载点速度下表现为速度弱化并伴有准周期性的黏滑,在较高加载点速度下又有转向速度强化的趋势,σ2的提高使得速度弱化的范围逐渐减少,滑动趋于稳定.上述两次转换对应不同的微破裂特征,在较高速度下从速度弱化转换为速度强化时,断层滑动伴有能量较小但频度很高的微破裂活动,而在较低速度下从速度弱化转换为速度强化时,断层滑动伴有间歇性的微破裂,这与断层带的微观结构特征有较好的对应关系,表明其转换机制是不同的. 相似文献
16.
17.
Field studies and seismic data show that semi-brittle flow of fault rocks probably is the dominant deformation mechanism at the base of the seismogenic zone at the so-called frictional-plastic transition. As the bottom of seismogenic fault, the dynamic characteristics of the frictional-plastic transition zone and plastic zone are very important for the seismogenic fault during seismic cycles. Granite is the major composition of the crust in the brittle-plastic transition zone. Compared to calcite, quartz, plagioclase, pyroxene and olivine, the rheologic data of K-feldspar is scarce. Previous deformation studies of granite performed on a quartz-plagioclase aggregate revealed that the deformation strength of granite was similar with quartz. In the brittle-plastic transition zone, the deformation characteristics of granite are very complex, temperature of brittle-plastic transition of quartz is much lower than that of feldspar under both natural deformation condition and lab deformation condition. In the mylonite deformed under the middle crust deformation condition, quartz grains are elongated or fine-grained via dislocation creep, dynamic recrystallization and superplastic flow, plagioclase grains are fine-grained by bugling recrystallization, K-feldspar are fine-grained by micro-fractures. Recently, both field and experimental studies presented that the strength of K-feldspar is much higher than that of quartz and plagioclase. The same deformation mechanism of K-feldspar and plagioclase occurred under different temperature and pressure conditions, these conditions of K-feldspar are higher than plagioclase. The strength of granite is similar to feldspar while it contains a high content of K-feldspar. High shear strain experiment studies reveal that granite is deformed by local ductile shear zones in the brittle-plastic transition zone. In the ductile shear zone, K-feldspar is brittle fractured, plagioclase are bugling and sub-grain rotation re-crystallized, and quartz grains are plastic elongated. These local shear zones are altered to local slip-zones with strain increasing. Abundances of K-feldspar, plagioclase and mica are higher in the slip-zones than that in other portions of the samples (K-feldspar is the highest), and abundance of quartz is decreased. Amorphous material is easily formed by shear strain acting on brittle fine-grained K-feldspar and re-crystallized mica and plagioclase. Ductile shear zone is the major deformation mechanism of fault zones in the brittle-plastic transition zone. There is a model of a fault failed by bearing constant shear strain in the transition zone:local shear zones are formed along the fractured K-feldspar grains; plagioclase and quartz are fine-grained by recrystallization, K-feldspar is crushed into fine grains, these small grains and mica grains partially change to amorphous material, local slip-zones are generated by these small grains and the amorphous materials; then, the fault should be failed via two ways, 1)the local slip-zones contact to a throughout slip-zone in the center of the fault zone, the fault is failed along this slip-zone, and 2)the local slip-zones lead to bigger mineral grains that are in contact with each other, stress is concentrated between these big grains, the fault is failed by these big grains that are fractured. Thus, the real deformation character of the granite can't be revealed by studies performing on a quartz-plagioclase aggregate. This paper reports the different deformation characters between K-feldspar, plagioclase and quartz under the same pressure and temperature condition based on previous studies. Then, we discuss a mode of instability of a fault zone in the brittle-plastic transition zone. It is still unclear that how many contents of weak mineral phase(or strong mineral phase)will control the strength of a three-mineral-phase granite. Rheological character of K-feldspar is very important for study of the deformation characteristic of the granitic rocks. 相似文献