共查询到20条相似文献，搜索用时 15 毫秒
1.
自然条件下,颗粒介质大多以非规则单元形态存在。非规则几何形态对颗粒介质的宏观力学性能有很大影响。针对颗粒单元的不同几何形态,采用团颗粒单元对离散介质的直剪试验过程进行了离散元数值计算,详细地讨论了颗粒形态对离散介质剪切强度的影响。该非规则颗粒由不同形态、不同数目、镶嵌尺寸、组合方位和颗粒大小的球形颗粒进行随机构造,其在局部与整体坐标之间的转动、力矩和方位关系通过4元素方法进行确定,基本球体颗粒之间的作用力采用具有Mohr-Coulomb摩擦定侓的Hertz-Mindlin非线性接触模型,并考虑了非线性法向粘滞力的影响。通过构造7种具有相同的质量概率分布的不同形态的团颗粒,在不同法向应力下,对团颗粒的直剪试验进行了离散元模拟,分析了不同形态颗粒的剪切强度。通过对不同形态颗粒介质剪切强度的数值分析,进一步揭示了非规则颗粒间的咬合互锁效应,为分析非规则颗粒的宏观动力特性提供了依据。 相似文献
2.
为实现结构性砂土离散元接触模型合理性的三维试验验证,设计了一套可用于三维半球形理想胶结颗粒成型及实现不同加载条件下的接触力学特性测试装置,制备了一定胶结尺寸的环氧树脂半球形颗粒胶结试样,在一系列辅助加载装置中初步开展了不同加载条件（拉伸、压缩、剪切、弯转、扭转）下的力学性能测试。结果表明,该装置可用于实现三维情况下胶结颗粒接触力学特性测试;不同加载条件下的实测试验结果与二维试验成果基本一致;峰值剪切、弯矩、扭矩随着法向荷载的增大呈现先增大后减小的趋势,存在一个相同的临界法向荷载。 相似文献
3.
接触模型的宏?细观参数标定是成功使用离散元方法的关键。在离散元的接触模型中线性接触模型与抗转线性接触模型均可用于模拟砂性土的力学行为,其中抗转线性接触模型在模拟密砂的剪胀性方面具备优势。采用抗转线性接触模型对室内密实砂土三轴试验进行了离散元模拟,验证了抗转线性接触模型的可靠性;进而系统分析了颗粒间摩擦系数、刚度比和抗转动系数等细观参数与砂土峰值内摩擦角、残余内摩擦角、峰值剪胀角等宏观参数的相关关系并进行了验证;揭示了偏应力作用下,细观参数对密实砂土试样内部剪切带宽度与倾角变化的影响规律,提出了考虑剪胀角的剪切带倾角经验公式。通过研究建立了抗转线性接触模型宏?细观参数的量化关系并给出了标定参数的具体流程图,提出了快速标定宏观参数的方法并应用实例进行了验证,为采用抗转线性接触模型精准模拟密实砂土的力学特性提供依据。 相似文献
4.
通过室内大型直剪试验和基于PFC2D的颗粒离散元数值模型,探讨考虑块石破碎的土石混合料的剪切特性及块石破碎特征。以土石混合料室内大型直剪试验和筛分试验为基础,提出了一种能真实描述块石形态特征并准确反映块石破碎效应的土石混合料颗粒离散元数值建模方法,模拟并分析了6种含石量土石混合料在4种不同法向应力作用下的剪切特性及块石破碎特征。结果表明：土石混合料抗剪强度随含石量的增大而增大,且基本符合摩尔-库仑（M-C）强度准则,随着含石量增大,内摩擦角呈现“慢-快-慢”增长趋势,黏聚力则呈现先增后减再增大的变化趋势。剪切后土石混合料块石破碎形式可归纳为表面研磨、局部破碎、完全破裂、完全破碎4种方式。提出了一种新的颗粒破碎指标,该指标能够准确描述粒径大于5 mm的块石的破碎程度,其随含石量和法向应力的增大而增大。通过对土石混合料颗粒离散元数值模型剪切面的分析发现,剪切面出现“剪斜”现象,其起伏程度随含石量增大愈加明显,且随着含石量增大剪切面附近剪裂隙数量增多,土石混合料在剪切过程中的破坏为拉-剪混合破坏。 相似文献
5.
为了研究颗粒棱角对颗粒材料力学行为的影响,建立了具有不同棱角度的对称多面体颗粒,采用了一种简单并适合任意颗粒形状的接触本构模型,对三维离散元开源程序YADE进行了修改,研究了颗粒棱角度在模拟直剪试验中的影响以及接触力各向异性在剪切过程中的演化规律。研究结果表明,颗粒棱角度越小,颗粒间相互咬合自锁的作用越小,颗粒受剪更易转动,致使颗粒体系的剪切强度和剪胀性下降;竖向加载力越大,颗粒棱角度的影响越明显;法向接触力的各向异性在剪切过程中表现为先增后减最后趋向稳定的趋势;法向接触力的各向异性变化程度随颗粒棱角度的增大而增大。 相似文献
6.
Venanzio R. Greco 《Geotechnical and Geological Engineering》2016,34(2):585-603
This paper presents a theoretical approach to evaluate the uncertainties and the correlation of the shear strength parameters c and t (cohesion and friction coefficient), obtained in direct shear tests. The analysis is based on the hypothesis that the soil is statistically homogeneous, with shear strength normally distributed having an expected resistance which is linearly dependent on the effective normal stress. With regard to the scatters of the population of the shear strength, two further statements have been formulated for the standard deviation: (1) a constant value, independent of the effective normal stresses and (2) a value which is linearly dependent on the normal effective stresses as a consequence of a constant coefficient of variation. The investigation shows that the strength parameters are negatively correlated and the coefficient of correlation and the coefficients of variation of cohesion and friction angle are highly dependent on the number of shear tests and the normal stresses used in the tests. 相似文献
7.
胶结颗粒接触力学特性测试装置研制 总被引：5，自引：2，他引：3
为验证天然结构性砂土离散元模拟中接触模型及其参数的合理性,设计了一套用于理想胶结颗粒成型及实现不同加载条件下接触力学特性测试装置。通过胶结颗粒成型装置在两大小相同的铝棒间形成具有特定几何尺寸的胶结物,随后,采用一系列辅助加载装置实现简单及复杂加载条件下胶结颗粒接触力学特性的测试。试验结果表明：该装置可用于胶结颗粒在不同加载条件下接触力学特性的测试,实测胶结颗粒接触力学响应与天然砂土离散元中接触模型基本相符,且其抗剪和抗扭强度均随着法向压力的增大而增大,在三维应力空间中胶结颗粒强度包线呈椭圆抛物面状。 相似文献
8.
转动阻抗被定义为作用颗粒接触上的一对对称力偶,用来抵抗颗粒之间的相互转动。将转动阻抗引入到离散元模拟中是对传统离散单元法的重要改进。开发出考虑颗粒转动阻抗的接触模型,并将其嵌入到PFC2D中,利用该模型进行粗粒土的双轴剪切数值模型试验,研究剪切过程中转动阻抗对粗粒土的宏细观力学性质的影响。结果显示,在宏观方面,颗粒转动阻抗对粗粒土的宏观力学行为（应力-应变及体应变-轴应变行为）有重要的影响,随着转动阻抗的增加,粗粒土的剪切强度和最大摩擦角随之增加,这与已有的研究结果一致,证明所建模型是可靠的;在微观方面,考察转动阻抗对粗粒土内部微观结构的影响发现,随着转动阻抗的增加,粗粒土的内部的接触数目减少,而粗粒土的剪切强度增加,表明转动阻抗能够提高粗粒土力链网络的稳定性,同时发现随着转动阻抗的增加,粗粒土的各向异性增加主要是强力链各向异性的增加,说明转动阻抗增强了强力链的传递力的能力以及抵抗力链屈曲破坏能力。数值模拟结果表明,增加颗粒转动阻抗,粗粒土出现组构与轴应变非共轴的现象。 相似文献
9.
Wei Shao Bora Cetin Yadong Li Jingpei Li Lin Li 《Geotechnical and Geological Engineering》2014,32(4):901-910
The addition of cementitious admixtures and/or inclusion of fibers are frequently used in practice to stabilize soils and to improve their mechanical properties. In this study, ring shear tests were conducted to investigate mechanical properties such as shear strength, angle of friction and cohesion values of randomly distributed discrete fiber-reinforced sand mixtures. The length and aspect ratio of the fibers used in the current study were 12 mm and 120, respectively. Specimens were prepared at four different fiber ratios (0.1, 0.3, 0.6, and 0.9 % by weight of sand). A series of ring shear tests were carried out on sand alone and fiber-reinforced sand mixtures at different normal stresses. The test results indicated that the addition of fiber had a significant effect on the shear strength of the sand. Shear stress of the unreinforced sand increases 1.29–2.32, 1.16–1.39, and 1.07–1.5 times at a normal stress of 50, 150, and 250 kPa, respectively with fiber inclusion. Fiber content had positive effects on improving the shear strength parameters (angle of internal friction and cohesion) of the mixtures. The cohesion and angle of internal friction of fiber-reinforced sand prepared at different ratios of fiber increased by 5.3–27.4 kPa and 2.0°–7.3° respectively. The inclusion of fibers improves the ductility of the soil by preventing the loss of post-peak strength. 相似文献
10.
A. D. Jefferson 《国际地质力学数值与分析法杂志》2002,26(5):515-535
A model for formed cracks in concrete is presented. The model can be used in isolation for existing cracks or linked with other damage or plasticity models and applied once a crack has fully formed. It can be applied directly to interface finite elements or used to control the behaviour of crack planes in more general constitutive models that are applied to 2D and 3D continuum elements. The focus of the present development is on aggregate interlock and crack closing behaviour, which is examined from available experimental data. A contact function is derived and is used to differentiate between three contact states. These states are named open, where there is no contact, interlock, for which the stresses depend upon the nearest distance to the contact surface and closed, for which the stresses depend upon the relative displacements directly. The model is developed within an elasto‐plastic framework using effective stresses, which are related to the total stresses via a contact proportion function. The relationship between the effective normal and shear yield stresses is found to be parabolic and the yield shear stress to be dependent upon the opening and embedment displacements. The performance of the model is assessed against experimental data from shear‐normal tests and it is concluded that the model is able to represent the key characteristics of the behaviour of formed cracks in concrete. Copyright © 2002 John Wiley & Sons, Ltd. 相似文献
11.
Earthquakes are recognized as resulting from a stick–slip frictional instability along faults. Based on the node‐to‐point contact element strategy (an arbitrarily shaped contact element strategy applied with the static‐explicit algorithm for modelling non‐linear frictional contact problems proposed by authors), a finite element code for modelling the 3‐D non‐linear friction contact between deformable bodies has been developed and extended here to analyse the non‐linear stick–slip frictional instability between deformable rocks with a rate‐ and state‐dependent friction law. A typical fault bend model is taken as an application example to be analysed here. The variations of the normal contact force, the frictional force, the transition of stick–slip instable state and the related relative slip velocity along the fault between the deformable rocks and the stress evolution in the total bodies during the different stages are investigated, respectively. The calculated results demonstrate the usefulness of this code for simulating the non‐linear frictional instability between deformable rocks. Copyright © 2003 John Wiley & Sons, Ltd. 相似文献
12.
钙质砂与钢板接触面力学特性试验研究 总被引：3，自引：0，他引：3
对一种人工制备的钙质砂与光滑铜板接触面进行了一系列的单调和循环剪切试验,表明钙质砂与光滑钢板的接触属于摩擦接触,界面剪应力与正应力之比与剪切位移关系有较好的归一性。等正应力试验中钙质砂的的缩性较大;等体积试验中接触面的抗剪强度因正应力的降低而远低于等正应力试验;循环剪切中加荷与卸荷曲线基本重合,经历循环剪切作用后接触面的抗剪强度有降低的趋势。界面湿摩擦系数低于干摩擦系数。 相似文献
13.
A new finite element model based on a large strain formulation has been developed to study cone penetration in normally consolidated sand. An auto‐adaptive remeshing technique was utilized for handling the very large distortion of sand surrounding the cone tip. A frictional contact interface utilizing Mohr–Coulomb's theory was chosen to represent interactions between the surface of the cone and sand. To model the sand behaviour, the non‐associated Drucker–Prager constitutive model was selected. ABAQUS, a commercial finite element software package, was used to implement the model. The explicit solution algorithm was chosen due to its effectiveness for complicated contact problems. Analysis results proved that the model successfully captured the cone penetration behavior in sand. In addition, a chart to predict internal friction angles based on cone tip resistance for different vertical effective stresses was provided. This paper also shows a typical distribution of sleeve resistance, tip resistance—penetration relationship, and typical contours of vertical, horizontal, and shear stresses in normally consolidated sand. Finally, a non‐uniform resistance was found along the length of the friction sleeve. Copyright © 2003 John Wiley & Sons, Ltd. 相似文献
14.
单调荷载下砂土变形过程数值模拟及细观机制研究 总被引：6，自引：0，他引：6
采用离散单元法的颗粒流理论,模拟了松砂和密砂在单调荷载作用下的变形过程,研究了砂土渐进破坏过程中的宏观力学行为和细观组构参量的演化规律。采用PFC的FISH语言开发了细观组构统计程序,通过记录加载不同时刻试样的细观参量,如配位数、接触法向分布、粒间法向接触力、切向接触力等的演化,分析了砂土变形过程中细观组构变化与宏观力学响应之间的内在联系。应用表征上述量的组构参数研究了砂土的诱发各向异性,探讨了松砂剪缩、密砂剪胀的细观机制。研究成果对于揭示砂土变形的细观机制以及建立砂土的细观力学模型具有重要意义。 相似文献
15.
基于微观胶结厚度模型的深海能源土宏观力学特性离散元分析 总被引：1，自引：0，他引：1
首先,引入蒋明镜等提出的考虑水合物胶结厚度的深海能源土粒间微观胶结模型,用以反映能源土颗粒之间水合物微观胶结接触力学特性;其次,采用C++语言将模型程序化,并将其引入离散单元法中;然后,对选定的水合物饱和度经过实际二维离散元模拟调算,得出相应的水合物胶结尺寸,以修正水合物临界胶结厚度、最小胶结厚度及胶结宽度,进而确定水合物微观胶结参数;最后,根据所确定的胶结参数,针对不同水合物饱和度试样进行能源土宏观力学特性离散元双轴试验模拟,并从应力-应变、体变、剪胀角等方面与Masui等所进行的能源土室内三轴试验进行对比分析。结果表明：采用考虑粒间胶结厚度的水合物微观胶结模型,能够定性反映深海能源土的宏观力学特性,能源土试样的峰值强度、黏聚力和剪胀角均随水合物饱和度的增加而增加,但水合物饱和度对内摩擦角的影响规律不明朗;能源土试样的峰值强度、残余强度及体积剪缩量随着有效围压的增大而增大;剪胀角随有效围压的增大而减小。 相似文献
16.
Effects of Material Composition and Water Content on the Mechanical Properties of Landslide Deposits Triggered by the Wenchuan Earthquake 总被引：3，自引：0，他引：3
Abundant landslide deposits were triggered by the Wenchuan earthquake, providing a rich source of material for subsequent debris flows or slope failures under rainfall conditions. A good understanding of the physical and mechanical properties of the landslide deposits is very important to the research on slope failure mechanisms and the initiation of debris flow. Laboratory biaxial compression tests are used to study the material compositions and water content impacts on the mechanical properties of landslide deposits, and a discrete element method (a bond-contact model) is used to study the particle stiffness, bond force, friction coefficient and confining stress impact on the mechanical behaviors and the relationships between the numerical and experimental parameters. The experimental results show that the failure stress of landslide deposits is decreased with increasing content of fine particles and also with increased water content, especially at the initial increasing stage. Cohesion of the saturated landslide deposits is increased, but the friction angle is decreased with the increase in the fine particle content. Shear strength parameters (the cohesion and friction angle) are decreased with the increasing water content at the initial increasing stage, and then, they slowly decrease. There is a critical value of the water content at 5%–7% (in weight) for the failure stress and shear strength parameters of the landslide deposits. Quadratic equations are presented to describe the relation between the bond force and cohesion, and the numerical friction coefficient and the experimental friction angle. 相似文献
17.
A multiscale DEM-LBM analysis on permeability evolutions inside a dilatant shear band 总被引：1，自引：1，他引：0
This paper presents a multiscale analysis of a dilatant shear band using a three-dimensional discrete element method and a lattice Boltzmann/finite element hybrid scheme. In particular, three-dimensional simple shear tests are conducted via the discrete element method. A spatial homogenization is performed to recover the macroscopic stress from the micro-mechanical force chains. The pore geometries of the shear band and host matrix are quantitatively evaluated through morphology analyses and lattice Boltzmann/finite element flow simulations. Results from the discrete element simulations imply that grain sliding and rotation occur predominately with the shear band. These granular motions lead to dilation of pore space inside the shear band and increases in local permeability. While considerable anisotropy in the contact fabric is observed with the shear band, anisotropy of the permeability is, at most, modest in the assemblies composed of spherical grains. 相似文献
18.
This report presents a numerical investigation of the shear behavior of binary mixtures via a two-dimensional discrete element method. The effect of the coarse particle content on the peak shear strength of mixtures is investigated for different contact-type friction coefficients. A detailed analysis on the anisotropies enables us to understand the microscopic mechanisms that result in the dependency of the peak shear strengths on the coarse particle content. The contributions of different contact types to the peak shear strength are quantified. Lastly, the inter-particles structures are examined when the binary mixtures become coarse-particle-supported structures. 相似文献
19.
研究荷载在岩石中的传递机理对岩石工程性质研究具有重要意义。本文以石灰岩试样为例,使用颗粒流方法来研究这一传递机理。研究试样大小为50 mm× 50 mm,岩石成分使用圆盘颗粒集合体来表征,颗粒间的接触模型采用平行连接模型,岩石的弹性模量、峰值应力和泊松比分别为44.24 GPa、101.05 MPa和0.267;将大于平均接触力的力链作为强力链,得到了外部荷载下试样中的强力链分布情况,研究了试样局部孔隙率、配位数等细观参数对接触力大小的影响,探讨了颗粒摩擦系数不同时外荷达到峰值应力后颗粒的接触力分布情况。结果表明,在全部颗粒接触点中,只有19.8%接触点的接触力大于平均接触力,但这些接触点应变能却占总应变能的75%;当法向接触力与切向接触力比值大于3.5时,试样峰后应力主要由法向接触力控制;与样品破坏前相比,破坏后样品中的局部孔隙率变化不大,只减少了0.002。 相似文献
20.
为了揭示新型注浆成型螺纹桩的承载力特性及桩土接触特性,利用二维离散元（DEM）数值分析不同螺纹间距的桩-土接触特性。在既有螺纹桩-土界面的大型直剪试验方案的基础上,建立模拟试验的离散元模型。通过模拟试验的伺服加载机制,实现在接触面法向上施加恒定的压力,然后水平移动接触面底板进行剪切,得到不同螺纹数下剪切位移与剪切应力的关系曲线、孔隙比分布图和力链传力机制。离散元分析表明,存在一个最优的螺纹间距,使接触面的极限抗剪强度最大;螺纹桩桩土接触面周围土体会出现一个拱形的破坏面,该微观机制与室内试验观察一致。 相似文献