共查询到20条相似文献，搜索用时 359 毫秒
1.
剑桥模型只适用于正常固结软黏土,不能描述不等向固结土的应力-应变行为的各向异性特性。基于剑桥模型,在其椭圆屈服面中引入各向异性张量和一个形状参数,建立了一个各向异性屈服面,提出了一个适用于等向和不等向固结软黏土的本构模型。各向异性张量的初始值由初始固结应力状态确定,其演化过程由一个与塑性剪应变和塑性体应变都有关的硬化法则描述。形状参数的引入保证了各向异性屈服面的灵活性和适应性。通过对Boston Blue黏土、高岭土和Otaniemi黏土的三轴试验结果的模拟,验证了模型的模拟能力。 相似文献
2.
3.
天然土体的初始各向异性通常可对其后继循环特性产生显著影响。现有考虑循环载荷作用的土体弹塑性模型,往往采用类似修正剑桥模型的椭圆形屈服面,已有研究表明,该椭圆形屈服面因其拉伸弹性区域偏大,针对天然K0固结状态的土体,其计算精度较差。基于新近提出的广义各向同性硬化准则,在边界面方程中引入初始各向异性张量,并采用空间滑动面破坏准则（SMP）的变换应力法,建立了能考虑饱和黏土初始各向异性的循环边界面塑性模型。分别针对等压和偏压固结的饱和黏土静、动三轴试验进行模拟,结果表明,该模型能合理反映土体的初始各向异性及其后继循环动力特性。 相似文献
4.
由于加荷方式不同,土体在复杂应力状态下在各主应力方向上应力-应变关系表现出显著应力各向异性,在常规三轴试验基础上,采用经典弹塑性理论各向同性土体模型对此不能合理描述。通过真三轴试验,总结应力各向异性柔度矩阵规律,结合试验规律进行相应理论研究,用非线性各向异性弹性矩阵代替弹塑性模型的弹性矩阵,用具有各向异性屈服准则的弹塑性模型描述塑性部分,建立非线性各向异性弹性-塑性模型,可以改善柔度矩阵矩阵形态,反映复杂应力状态下土体应力各向异性特征。 相似文献
5.
饱和软黏土动力学特性循环扭剪试验研究 总被引：2，自引：0，他引：2
以饱和软黏土的循环扭剪试验研究为基础,阐明不固结不排水条件下饱和软黏土的动力学特性。在循环扭剪和循环三轴两种不同试验应力状态下,通过研究不同围压和不同静、动应力组合下饱和软黏土的应力等效破坏关系和应变等效破坏关系,提出在循环荷载作用下饱和软黏土的循环破坏同样遵循Mises屈服准则,且在Mises屈服准则下,饱和软黏土的循环强度趋于不变量。循环破坏的过程可以等效为一种拟静力弹塑性循环蠕变,建立了饱和软黏土循环累积变形随静荷载、循环荷载以及循环破坏振次之间的关系式。上述结论分别从应力和变形两个方面阐述饱和软黏土的动力学特性,与试验应力状态和围压无关,可以推广到一般应力状态下。 相似文献
6.
天然沉积粉质黏土的应力路径试验研究 总被引：1，自引：0，他引：1
天然沉积土在沉积过程中产生了结构性和各向异性,使其受力变形特性与重塑土存在明显的差异。实际工程中的天然土体往往在受荷过程中会经历不同的应力路径,因此,需要开展考虑结构性和各向异性影响的应力路径试验。通过研究不同应力路径下土体的力学特性,为建立复杂应力路径下的合理的本构模型提供试验依据。采用大直径PVC管取样器获取张家港地区地下2.5 m深的粉质黏土不扰动土样,通过GDS三轴仪对土样进行了K0固结不同排水应力路径试验。结果表明,应力路径对不扰动土样的体积变形和剪切变形均有显著影响,且球应力和偏应力对土的体应变和剪应变存在交叉影响。无论以体积变形为主还是剪切变形为主的应力路径下,应力-应变曲线都有明显的屈服性状。通过描绘试验所得各应力路径下的屈服点,获得张家港不扰动土样的屈服轨迹大致呈倾斜的椭圆形状,采用Wheeler模型的屈服面与试验屈服点的吻合程度要优于Nakano模型。 相似文献
7.
修正了传统隐式回映算法,建立了适用于饱和黏土循环动力分析的边界面塑性模型的完全隐式积分格式。该模型基于无弹性域概念和临界状态理论,采用各向同性、运动硬化准则、旋转的边界面,并引入表征土体结构损伤和重塑程度的损伤变量以反映循环载荷作用下饱和黏土的各向异性、刚度、强度软化及塑性变形累积等特征。针对等压固结 和偏压固结 的饱和高岭黏土的不排水三轴试验进行模拟,采用不同的应变增量步长进行计算,并与试验数据对比,结果表明,修正隐式回映算法应用于该类边界面模型的合理性、积分格式的精确性和稳定性;另外,结合有限元软件自动时间步长的增量迭代解法,对饱和黏土应力控制的不排水动三轴试验进行预测,结果表明,修正的适用于该边界面的塑性模型隐式回映算法可以得到比较合理的数值分析结果,能够反映饱和黏土的循环刚度的退化和强度的弱化等动力特性。 相似文献
8.
复杂应力路径下杭州原状软黏土破坏标准研究 总被引：2，自引：1，他引：1
采用空心圆柱扭剪仪对主应力轴方向固定不变定向不排水剪切应力路径下杭州原状软黏土破坏标准进行试验研究,重点探讨了中主应力参数b、大主应力方向角?及孔压积累对剪切过程中黏土抗剪强度的影响,并提出原状软黏土剪切破坏的标准。试验结果表明,中主应力参数的变化没有对应力应变变化模式和试验应力路径产生影响,随着中主应力参数的增大,黏土抗剪强度的变化并没有呈现出一定的规律性;大主应力方向角对原状软黏土强度的影响反映出原生各向异性对黏土抗剪强度的控制作用;黏土样在剪切后期会产生显著的孔压积累,影响了黏土强度的发挥。考虑中主应力参数等影响因素,通过分析广义剪应力-应变曲线的变化情况,取广义剪应力qJ的峰值作为原状软黏土的剪切破坏标准。 相似文献
9.
在临界状态弹塑性力学的框架内,建立了可以考虑循环荷载作用下各向异性对饱和软土力学特性影响的边界面塑性模型。该模型采用非关联的流动法则,引入了反映土体各向异性的内变量,利用该内变量的初始值描述初始各向异性,采用一种理论更为严谨、模型参数确定更为恰当的旋转硬化法则描述循环加载过程中各向异性的演化,利用更新映射中心的径向映射法则和与塑性偏应变路径长度有关的塑性模量插值规律,保证模型能够模拟循环加载时应力-应变响应的非线性、滞回性、应变累积性等基本特性,解释了模型参数的物理意义和确定方法,特别是给出了一种合理确定描述土体初始各向异性状态变量方法。通过文献中等压固结和偏压固结饱和黏土的循环三轴试验结果与模型预测结果的对比验证了模型的合理性。 相似文献
10.
结构性黏土的压缩变形特性 总被引：1，自引：0，他引：1
海相软黏土的结构性对土体的变形与强度特性有着重要的影响,这种影响与爆炸挤淤置换法处理软基的置换深度直接相关,是海堤基础沉降与稳定性分析的不确定因素。为了探究结构性对海堤地基沉降的影响,并对海相软黏土的压缩特性进行定量分析,建立结构性黏土的压缩变形模型,同时给出模型参数的确定方法。利用文献中的试验数据对模型进行了验证,结果表明模型不仅适用于一维应力状态下的变形分析,能够描述三轴应力状态下结构性黏土的压缩特性。利用所建模型对浙江漩门地区海相软黏土的压缩特性进行模拟,分析表明,模型能较好地考虑结构性对该地区软黏土压缩变形的影响,为该地区海堤沉降的预测提供量化分析的手段,有助于加强结构性黏土地区海堤地基设计与施工的理论基础。 相似文献
11.
Kristian Krabbenhøft Sergio Andres Galindo-Torres Xue Zhang Jørgen Krabbenhøft 《国际地质力学数值与分析法杂志》2019,43(17):2652-2666
A total stress model applicable to clays under undrained conditions is presented. The model involves three strength parameters: the undrained shear strengths in triaxial compression, triaxial extension, and simple shear. The amount of physical anisotropy implied by the model is a function of the relative magnitude of these three strengths assuming a Mises-type plastic potential. Elastoplastic deformation characteristics below failure are accounted for by a hardening law requiring two additional parameters that can be related to the axial strains halfway to failure in triaxial compression and extension. Finally, elasticity is accounted for by Hooke law. The result is a relatively simple model whose parameters can all be inferred directly from a combination of in situ and standard undrained laboratory tests. The model is applied to a problem involving the horizontal loading of a monopile foundation for which full scale tests have been previously conducted. The model shows good agreement with the measured data. 相似文献
12.
Jianhong Jiang Hoe I. Ling Victor N. Kaliakin Xiangyong Zeng Ching Hung 《Acta Geotechnica》2017,12(2):335-348
An anisotropic time-dependent bounding surface model for clays is developed by generalizing a previous time-independent model that adopts a flexible bounding surface. It is based on the framework for coupled elastoplasticity–viscoplasticity for clays and Perzyna’s overstress theory. Three viscoplastic parameters were introduced and explained in detail. The model was validated against undrained creep tests for both isotropically and anisotropically consolidated clays, undrained and drained stress relaxation tests on some undisturbed clays, and undrained triaxial tests with varying strain rates on natural Hong Kong marine deposit clay. The general agreement between the model simulations and test results was satisfactory. The varying effects of lower-level parameters were discussed on the undrained multistage stress relaxation response for normally consolidated soils which had been ignored in literature. The flexibility of the model in capturing the shear strengths, which is the unique feature of the current model, was shown in the simulations of time-dependent triaxial tests on Taipei silty clay. All the simulations show that the proposed model is a relatively practical model considering both anisotropy and time dependency of clays. 相似文献
13.
按照在最佳系泊点受倾斜荷载作用的张紧式吸力锚的破坏机制,建议了利用软土不排水循环剪切强度计算软土中吸力锚循环承载力的极限平衡分析方法。该方法考虑了平均系泊荷载在土中引起的平均剪应力对土体循环剪切强度、进而对锚循环承载力的影响。为了说明该方法的可行性,进行了大量张紧式吸力锚在平均系泊荷载与循环荷载共同作用下的承载力模型试验。依据试验结果确定了锚被竖向拔出土层时系泊点的位移破坏标准,并据此确定了与不同模型试验条件对应的循环承载力。进而利用循环三轴试验确定的土层不排水循环强度随平均应力的变化关系和实测的土层剪切强度,通过极限平衡分析计算了与模型试验对应的循环承载力。计算与模型试验结果比较表明,对于张紧式吸力锚被竖向拔出土层的破坏模式,计算结果比模型试验结果偏大,平均偏大1.9%,绝大多数偏差在10%以内。因此,对于软土中的张紧式吸力锚,如果采用该方法计算与竖向拔出土层破坏模式相应的循环承载力时,将结果减小10%是恰当的。 相似文献
14.
This paper evaluates the performance of a generalized effective stress soil model for predicting the rate independent behaviour of freshly deposited sands, while a companion paper describes model capabilities for clays and silts. Most material parameters can be obtained from standard laboratory data, including hydrostatic or one‐dimensional compression, drained and undrained triaxial shear testing. A compilation of data on compression behaviour allows for estimation of compression parameters when this type of data is not available. Extensive comparisons of model predictions with measured data from undrained triaxial shear tests shows that the model gives excellent predictions of the transition from dilative to contractive shear response as the confining pressure and/or the initial formation void ratio increases. A parametric study of drained response shows that the model describes realistically the variation of peak friction angle and dilation rate as a function of confining pressure and density when compared with an empirical correlation valid for many sands. The proposed formulation predicts a unique critical state locus for both drained and undrained triaxial testing which is non‐linear over the entire range of stresses and is in excellent agreement with recent experimental data. Overall, the model provides excellent predictions of the stress–strain–strength relationships over a wide range of confining pressures and formation densities. Copyright © 2002 John Wiley & Sons, Ltd. 相似文献
15.
软黏土加载速率效应特性试验研究:进展与趋势 总被引：1，自引：0，他引：1
大量的室内和现场试验都表明,软黏土的强度与变形速率相关。为了更深入地认识软黏土的加载速率效应特性,首先分析了一维应力条件下先期固结压力和三轴应力条件下不排水抗剪强度的加载速率效应及应力-应变关系的归一化,探讨了一维和三轴条件下的5个速率方程(2个指数形式和3个对数形式)在拟合黏土先期固结压力和不排水强度加载速率效应上的适用性;使用5个速率方程估计了一维和三轴条件下的加载速率参数,以及拟合了加载速率参数与液塑限的关系,并且分析了复杂应力(十字板剪切和旁压条件)下的非理想土单元体的黏土加载速率效应特性等;讨论了黏土加载速率效应特性在一维和三维、压缩与伸长、不同超固结比(OCR)条件下的统一性;最后,从香港黏土压缩与伸长和不同OCR条件下的剪缩、剪胀特性方面更深入地探讨了软黏土加载速率效应特性,并讨论了典型的剪缩、剪胀方程在黏土的力学特性模拟中的有效性。结果表明,为更好地描述黏土的应力剪胀特性,现有典型的剪胀关系需要更一步改进。 相似文献
16.
A simple critical-state-based double-yield-surface model for clay behavior under complex loading 总被引：9，自引：4，他引：5
The critical state concept has been widely used in soil mechanics. The purpose of this study is to apply this concept in the framework of multi-mechanism elastoplasticity. The developed model has two yield surfaces: one for shear sliding and one for compression. In this model, the location of the critical state line is explicitly considered and related to the actual material density to control the peak strength and the phase transformation characteristics. The stress reversal technique is incorporated into the model for describing clay behavior under complex loading including changes of stress direction. The determination of the model parameters is discussed; it requires only one drained or undrained triaxial test up to failure with an initial isotropic consolidation stage. The model is used to simulate drained and undrained tests under monotonic loading with different over-consolidation ratios on various remolded and natural clays, including true triaxial tests with different Lode’s angles. Drained and undrained tests under cyclic loadings are also simulated by using the set of parameters determined from monotonic tests. The comparison between experimental results and numerical simulations demonstrate a good predictive ability of this new simple model. 相似文献
17.
18.
The paper presents a simple constitutive model for normally consolidated clay. A mathematical formulation, using a single tensor-valued function to define the incrementally nonlinear stress–strain relation, is proposed based on the basic concept of hypoplasticity. The structure of the tensor-valued function is determined in the light of the response envelope. Particular attention is paid towards incorporating the critical state and to the capability for capturing undrained behaviour of clayey soils. With five material parameters that can be determined easily from isotropic consolidation and triaxial compression tests, the model is shown to provide good predictions for the response of normally consolidated clay along various stress paths, including drained true triaxial tests and undrained shear tests. 相似文献
19.
Rakesh J. Pillai I. Bushra R. G. Robinson 《Geotechnical and Geological Engineering》2013,31(2):801-808
Clays treated with lower cement contents often exhibit behaviour similar to stiff clays with planar failure surface under triaxial compression. In the present work the behaviour of a marine clay treated with 5 % cement, subjected to undrained triaxial compression tests is studied. The pre-consolidation pressure of the cemented clay due to the cementation bonding is observed to be very high. It is attempted to model the behaviour of cement treated clay using a bounding surface plasticity formulation as the plastic behaviour of the cemented clays within the yield surface has to be considered. The effect of cementation is included in the model as the pre-consolidation pressure obtained from consolidation tests. The tensile strength due to cementation bonds is included in the equation of the bounding surface. Simulations of the undrained triaxial compression tests on cemented clays are carried out and the results are validated with the experimental results. 相似文献
20.
为了研究上海软黏土的蠕变力学特性,开展了排水和不排水条件下上海软黏土的三轴蠕变力学试验,分析了不同围压水平、加卸荷水平对饱和软黏土蠕变特性的影响,得到了不同试验条件下上海软黏土蠕变的力学特性。试验结果表明:围压水平及加卸荷水平对软黏土蠕变变形有一定影响;土体蠕变变形特性与排水条件密切相关,排水条件下,固结效应削弱了土体蠕变现象;同等条件加载过程中不排水条件下土体变形量大,卸载后不排水条件下土体回弹较明显;不排水蠕变试验加载过程中,孔隙水压力随时间发展的变化规律与土体蠕变变形规律相似;排水蠕变试验加载过程中,固结变形和蠕变变形同时存在,排水量曲线在卸载后没有出现明显下降。 相似文献